Playing a Music Video takes too long to start

I have a 2 hour 45 minute music video on my Ipod. I can either watch the video or just hear the music from my song list (no video).
The video will start playing in a few seconds, but playing as a "song" will start after a few minutes. This does not look as normal, Wonder if this happens to all?
AMD 2.4 Ghz Windows XP Pro 1 Gb Ram Ipod 5g Black 60 Gb

I'm confused...
When you go to videos-->music videos and play the video, does it or does it not work?
Now when you play it under music, does it work?
Which one does it take long to load in?
btabz

Similar Messages

TS1702 Since updating ipad to 7IOS videos take too long to download and when playing they often stop

Since updating my ipad to 7IOS videos are too slow to download and often stop when playing. Any suggestions?

Since updating my ipad to 7IOS videos are too slow to download and often stop when playing. Any suggestions?

Ssh X11 forwarding takes too long to start any app. remotely

Hi,
I have a bizzare problem with %subject% for some time already.
Affected are all my Arch linux installations (all with: systemd, openbox (without Display Manager), and latest updates):
1. home desktop (core 2 duo, 2.4GHz, 3GB RAM).
2. one testing desktop in virtualbox on the desktop from prev. point.
3. work laptop (Intel Core i5, 4GB RAM).
All of these are connected via cable to the same home network 100MB router (using openwrt on asus wl-500g).
Normal ssh transmissions, like entering commands, or transfer of data via scp (even large amount of data for testing purposes because of this) works quick like expected.
The problem is, that if I try to start app. remotely via ssh X forwarding from and to any of these (affected also bidirectional), it takes always aprox. 2 minutes to start the app.
Afterwards, it works fast and fine.
Doesn't change anything, whether the X server is running on the server's side or not.
Have been testing it with some lightweight apps too, but makes no difference if it's e.g. mousepad, gedit, thunderbird, always the same 2 min. delay at their start.
Also, some time ago, I had an older (more than 10 years) laptop, also with Arch installed, using LXDE, and connected via wifi to this same router, which worked perfectly without any delay. Also the same time ago, I was yet running Ubuntu on the home desktop, when I installed Arch to the virtualbox mentioned in point 2, and the problem was already present on the virtual pc, but not on the Ubuntu or the older laptop with Arch I had before.
Later, when I switched home desktop to Arch (or I got new laptop in the work), the issue appeared instantly on the new Arch installations.
The sshd configuration is the basic from the package, with X forwarding enabled of course, thus no strange changes of mine.
I monitored the ssh communications with tcpdump, not to read the encrypted data itself , but to see whether the data is flowing, and there are flow outages (absolute quiet except of below mentioned exceptions) in the mentioned 2 minutes duration till app. startup:
- after ssh authentication, there is about 1 minute silence, when after this 1st minute some few data is flowing
- next, there is another 1 minute silence, after which the app. finally starts
I've also gathered ssh debugging informations, from both, server (where I'm connecting and trying to start app. remotely) and client, with description when waiting has been detected.
server:
/usr/sbin/sshd -ddd
debug2: load_server_config: filename /etc/ssh/sshd_config
debug2: load_server_config: done config len = 501
debug2: parse_server_config: config /etc/ssh/sshd_config len 501
debug3: /etc/ssh/sshd_config:15 setting ListenAddress 0.0.0.0
debug3: /etc/ssh/sshd_config:16 setting ListenAddress ::
debug3: /etc/ssh/sshd_config:35 setting LogLevel INFO
debug3: /etc/ssh/sshd_config:42 setting PermitRootLogin no
debug3: /etc/ssh/sshd_config:52 setting AuthorizedKeysFile .ssh/authorized_keys
debug3: /etc/ssh/sshd_config:68 setting PermitEmptyPasswords no
debug3: /etc/ssh/sshd_config:71 setting ChallengeResponseAuthentication no
debug3: /etc/ssh/sshd_config:92 setting UsePAM yes
debug3: /etc/ssh/sshd_config:94 setting AllowAgentForwarding yes
debug3: /etc/ssh/sshd_config:95 setting AllowTcpForwarding yes
debug3: /etc/ssh/sshd_config:97 setting X11Forwarding yes
debug3: /etc/ssh/sshd_config:98 setting X11DisplayOffset 10
debug3: /etc/ssh/sshd_config:99 setting X11UseLocalhost yes
debug3: /etc/ssh/sshd_config:104 setting UsePrivilegeSeparation sandbox
debug3: /etc/ssh/sshd_config:106 setting Compression delayed
debug3: /etc/ssh/sshd_config:109 setting UseDNS no
debug3: /etc/ssh/sshd_config:120 setting Subsystem sftp /usr/lib/ssh/sftp-server
debug1: sshd version OpenSSH_6.1p1
debug3: Incorrect RSA1 identifier
debug1: read PEM private key done: type RSA
debug1: private host key: #0 type 1 RSA
debug3: Incorrect RSA1 identifier
debug1: read PEM private key done: type DSA
debug1: private host key: #1 type 2 DSA
debug3: Incorrect RSA1 identifier
debug1: read PEM private key done: type ECDSA
debug1: private host key: #2 type 3 ECDSA
debug1: rexec_argv[0]='/usr/sbin/sshd'
debug1: rexec_argv[1]='-ddd'
debug3: oom_adjust_setup
Set /proc/self/oom_score_adj from 0 to -1000
debug2: fd 3 setting O_NONBLOCK
debug3: sock_set_v6only: set socket 3 IPV6_V6ONLY
debug1: Bind to port 22 on ::.
Server listening on :: port 22.
debug2: fd 4 setting O_NONBLOCK
debug1: Bind to port 22 on 0.0.0.0.
Server listening on 0.0.0.0 port 22.
debug3: fd 5 is not O_NONBLOCK
debug1: Server will not fork when running in debugging mode.
debug3: send_rexec_state: entering fd = 8 config len 501
debug3: ssh_msg_send: type 0
debug3: send_rexec_state: done
debug1: rexec start in 5 out 5 newsock 5 pipe -1 sock 8
debug1: inetd sockets after dupping: 3, 3
Connection from CLIENT_IP port 43333
debug1: Client protocol version 2.0; client software version OpenSSH_6.1
debug1: match: OpenSSH_6.1 pat OpenSSH*
debug1: Enabling compatibility mode for protocol 2.0
debug1: Local version string SSH-2.0-OpenSSH_6.1
debug2: fd 3 setting O_NONBLOCK
debug3: ssh_sandbox_init: preparing seccomp filter sandbox
debug2: Network child is on pid 6379
debug3: preauth child monitor started
debug3: privsep user:group 99:99 [preauth]
debug1: permanently_set_uid: 99/99 [preauth]
debug3: ssh_sandbox_child: setting PR_SET_NO_NEW_PRIVS [preauth]
debug3: ssh_sandbox_child: attaching seccomp filter program [preauth]
debug1: list_hostkey_types: ssh-rsa,ssh-dss,ecdsa-sha2-nistp256 [preauth]
debug1: SSH2_MSG_KEXINIT sent [preauth]
debug1: SSH2_MSG_KEXINIT received [preauth]
debug2: kex_parse_kexinit: ecdh-sha2-nistp256,ecdh-sha2-nistp384,ecdh-sha2-nistp521,diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 [preauth]
debug2: kex_parse_kexinit: ssh-rsa,ssh-dss,ecdsa-sha2-nistp256 [preauth]
debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] [preauth]
debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] [preauth]
debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-512,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 [preauth]
debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-512,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 [preauth]
debug2: kex_parse_kexinit: none,[email protected] [preauth]
debug2: kex_parse_kexinit: none,[email protected] [preauth]
debug2: kex_parse_kexinit: [preauth]
debug2: kex_parse_kexinit: [preauth]
debug2: kex_parse_kexinit: first_kex_follows 0 [preauth]
debug2: kex_parse_kexinit: reserved 0 [preauth]
debug2: kex_parse_kexinit: ecdh-sha2-nistp256,ecdh-sha2-nistp384,ecdh-sha2-nistp521,diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 [preauth]
debug2: kex_parse_kexinit: [email protected],[email protected],[email protected],ecdsa-sha2-nistp256,ecdsa-sha2-nistp384,ecdsa-sha2-nistp521,[email protected],[email protected],[email protected],[email protected],ssh-rsa,ssh-dss [preauth]
debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] [preauth]
debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] [preauth]
debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-512,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 [preauth]
debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-512,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 [preauth]
debug2: kex_parse_kexinit: none,[email protected],zlib [preauth]
debug2: kex_parse_kexinit: none,[email protected],zlib [preauth]
debug2: kex_parse_kexinit: [preauth]
debug2: kex_parse_kexinit: [preauth]
debug2: kex_parse_kexinit: first_kex_follows 0 [preauth]
debug2: kex_parse_kexinit: reserved 0 [preauth]
debug2: mac_setup: found hmac-md5 [preauth]
debug1: kex: client->server aes128-ctr hmac-md5 none [preauth]
debug2: mac_setup: found hmac-md5 [preauth]
debug1: kex: server->client aes128-ctr hmac-md5 none [preauth]
debug1: expecting SSH2_MSG_KEX_ECDH_INIT [preauth]
debug3: mm_key_sign entering [preauth]
debug3: mm_request_send entering: type 4 [preauth]
debug3: mm_key_sign: waiting for MONITOR_ANS_SIGN [preauth]
debug3: mm_request_receive_expect entering: type 5 [preauth]
debug3: mm_request_receive entering [preauth]
debug3: mm_request_receive entering
debug3: monitor_read: checking request 4
debug3: mm_answer_sign
debug3: mm_answer_sign: signature 0x13e3f80(100)
debug3: mm_request_send entering: type 5
debug2: monitor_read: 4 used once, disabling now
debug2: kex_derive_keys [preauth]
debug2: set_newkeys: mode 1 [preauth]
debug1: SSH2_MSG_NEWKEYS sent [preauth]
debug1: expecting SSH2_MSG_NEWKEYS [preauth]
debug2: set_newkeys: mode 0 [preauth]
debug1: SSH2_MSG_NEWKEYS received [preauth]
debug1: KEX done [preauth]
debug1: userauth-request for user USERNAME service ssh-connection method none [preauth]
debug1: attempt 0 failures 0 [preauth]
debug3: mm_getpwnamallow entering [preauth]
debug3: mm_request_send entering: type 6 [preauth]
debug3: mm_request_receive entering
debug3: monitor_read: checking request 6
debug3: mm_answer_pwnamallow
debug2: parse_server_config: config reprocess config len 501
debug3: mm_answer_pwnamallow: sending MONITOR_ANS_PWNAM: 1
debug3: mm_request_send entering: type 7
debug2: monitor_read: 6 used once, disabling now
debug3: mm_getpwnamallow: waiting for MONITOR_ANS_PWNAM [preauth]
debug3: mm_request_receive_expect entering: type 7 [preauth]
debug3: mm_request_receive entering [preauth]
debug2: input_userauth_request: setting up authctxt for USERNAME [preauth]
debug3: mm_start_pam entering [preauth]
debug3: mm_request_send entering: type 45 [preauth]
debug3: mm_request_receive entering
debug3: monitor_read: checking request 45
debug1: PAM: initializing for "USERNAME"
debug1: PAM: setting PAM_RHOST to "CLIENT_IP"
debug1: PAM: setting PAM_TTY to "ssh"
debug2: monitor_read: 45 used once, disabling now
debug3: mm_inform_authserv entering [preauth]
debug3: mm_request_send entering: type 3 [preauth]
debug2: input_userauth_request: try method none [preauth]
debug3: mm_request_receive entering
debug3: monitor_read: checking request 3
debug3: mm_answer_authserv: service=ssh-connection, style=
debug2: monitor_read: 3 used once, disabling now
debug1: userauth-request for user USERNAME service ssh-connection method publickey [preauth]
debug1: attempt 1 failures 0 [preauth]
debug2: input_userauth_request: try method publickey [preauth]
debug1: test whether pkalg/pkblob are acceptable [preauth]
debug3: mm_key_allowed entering [preauth]
debug3: mm_request_send entering: type 20 [preauth]
debug3: mm_key_allowed: waiting for MONITOR_ANS_KEYALLOWED [preauth]
debug3: mm_request_receive_expect entering: type 21 [preauth]
debug3: mm_request_receive entering [preauth]
debug3: mm_request_receive entering
debug3: monitor_read: checking request 20
debug3: mm_answer_keyallowed entering
debug3: mm_answer_keyallowed: key_from_blob: 0x13e1e20
debug1: temporarily_use_uid: 1000/100 (e=0/0)
debug1: trying public key file /home/USERNAME/.ssh/authorized_keys
debug1: Could not open authorized keys '/home/USERNAME/.ssh/authorized_keys': No such file or directory
debug1: restore_uid: 0/0
Failed publickey for USERNAME from CLIENT_IP port 43333 ssh2
debug3: mm_answer_keyallowed: key 0x13e1e20 is not allowed
debug3: mm_request_send entering: type 21
debug2: userauth_pubkey: authenticated 0 pkalg ssh-dss [preauth]
debug1: userauth-request for user USERNAME service ssh-connection method password [preauth]
debug1: attempt 2 failures 1 [preauth]
debug2: input_userauth_request: try method password [preauth]
debug3: mm_auth_password entering [preauth]
debug3: mm_request_send entering: type 10 [preauth]
debug3: mm_auth_password: waiting for MONITOR_ANS_AUTHPASSWORD [preauth]
debug3: mm_request_receive_expect entering: type 11 [preauth]
debug3: mm_request_receive entering [preauth]
debug3: mm_request_receive entering
debug3: monitor_read: checking request 10
debug3: PAM: sshpam_passwd_conv called with 1 messages
debug1: PAM: password authentication accepted for USERNAME
debug3: mm_answer_authpassword: sending result 1
debug3: mm_request_send entering: type 11
debug3: mm_request_receive_expect entering: type 46
debug3: mm_request_receive entering
debug1: do_pam_account: called
debug3: PAM: do_pam_account pam_acct_mgmt = 0 (Success)
debug3: mm_request_send entering: type 47
Accepted password for USERNAME from CLIENT_IP port 43333 ssh2
debug3: mm_auth_password: user authenticated [preauth]
debug3: mm_do_pam_account entering [preauth]
debug3: mm_request_send entering: type 46 [preauth]
debug3: mm_request_receive_expect entering: type 47 [preauth]
debug3: mm_request_receive entering [preauth]
debug3: mm_do_pam_account returning 1 [preauth]
debug3: mm_send_keystate: Sending new keys: 0x13e1c40 0x13e34c0 [preauth]
debug3: mm_newkeys_to_blob: converting 0x13e1c40 [preauth]
debug3: mm_newkeys_to_blob: converting 0x13e34c0 [preauth]
debug3: mm_send_keystate: New keys have been sent [preauth]
debug3: mm_send_keystate: Sending compression state [preauth]
debug3: mm_request_send entering: type 24 [preauth]
debug3: mm_send_keystate: Finished sending state [preauth]
debug1: monitor_read_log: child log fd closed
debug1: monitor_child_preauth: USERNAME has been authenticated by privileged process
debug3: mm_get_keystate: Waiting for new keys
debug3: mm_request_receive_expect entering: type 24
debug3: mm_request_receive entering
debug3: mm_newkeys_from_blob: 0x13f3b20(122)
debug2: mac_setup: found hmac-md5
debug3: mm_get_keystate: Waiting for second key
debug3: mm_newkeys_from_blob: 0x13f3b20(122)
debug2: mac_setup: found hmac-md5
debug3: mm_get_keystate: Getting compression state
debug3: mm_get_keystate: Getting Network I/O buffers
debug3: mm_share_sync: Share sync
debug3: mm_share_sync: Share sync end
debug3: ssh_sandbox_parent_finish: finished
debug1: PAM: establishing credentials
debug3: PAM: opening session
User child is on pid 6387
debug1: PAM: establishing credentials
debug1: permanently_set_uid: 1000/100
debug2: set_newkeys: mode 0
debug2: set_newkeys: mode 1
debug1: Entering interactive session for SSH2.
debug2: fd 7 setting O_NONBLOCK
debug2: fd 9 setting O_NONBLOCK
debug1: server_init_dispatch_20
debug1: server_input_channel_open: ctype session rchan 0 win 2097152 max 32768
debug1: input_session_request
debug1: channel 0: new [server-session]
debug2: session_new: allocate (allocated 0 max 10)
debug3: session_unused: session id 0 unused
debug1: session_new: session 0
debug1: session_open: channel 0
debug1: session_open: session 0: link with channel 0
debug1: server_input_channel_open: confirm session
debug1: server_input_global_request: rtype [email protected] want_reply 0
debug1: server_input_channel_req: channel 0 request x11-req reply 1
debug1: session_by_channel: session 0 channel 0
debug1: session_input_channel_req: session 0 req x11-req
debug3: sock_set_v6only: set socket 10 IPV6_V6ONLY
debug2: fd 10 setting O_NONBLOCK
debug3: fd 10 is O_NONBLOCK
debug1: channel 1: new [X11 inet listener]
debug2: fd 11 setting O_NONBLOCK
debug3: fd 11 is O_NONBLOCK
debug1: channel 2: new [X11 inet listener]
debug1: server_input_channel_req: channel 0 request exec reply 1
debug1: session_by_channel: session 0 channel 0
debug1: session_input_channel_req: session 0 req exec
debug2: fd 3 setting TCP_NODELAY
debug3: packet_set_tos: set IP_TOS 0x10
debug2: fd 14 setting O_NONBLOCK
debug2: fd 13 setting O_NONBLOCK
debug2: fd 16 setting O_NONBLOCK
debug2: channel 0: read 210 from efd 16
debug2: channel 0: rwin 2097152 elen 210 euse 1
debug2: channel 0: sent ext data 210
debug2: channel 0: read 380 from efd 16
debug2: channel 0: rwin 2096942 elen 380 euse 1
debug2: channel 0: sent ext data 380
debug2: channel 0: read 121 from efd 16
debug2: channel 0: rwin 2096562 elen 121 euse 1
debug2: channel 0: sent ext data 121
### Here started the waiting on the server's side, and continued later till the start of app.:
debug1: X11 connection requested.
debug2: fd 12 setting TCP_NODELAY
debug2: fd 12 setting O_NONBLOCK
debug3: fd 12 is O_NONBLOCK
debug1: channel 3: new [X11 connection from 127.0.0.1 port 46968]
debug2: channel 3: open confirm rwindow 2097152 rmax 16384
debug2: channel 0: read 62 from efd 16
debug2: channel 0: rwin 2096441 elen 62 euse 1
debug2: channel 0: sent ext data 62
debug1: X11 connection requested.
debug2: fd 15 setting TCP_NODELAY
debug2: fd 15 setting O_NONBLOCK
debug3: fd 15 is O_NONBLOCK
debug1: channel 4: new [X11 connection from 127.0.0.1 port 46972]
debug2: channel 4: open confirm rwindow 2097152 rmax 16384
debug2: channel 3: rcvd adjust 51268
debug2: channel 3: rcvd adjust 65536
debug2: channel 3: rcvd adjust 65536
debug2: channel 3: rcvd adjust 65536
debug2: channel 3: rcvd adjust 65536
debug2: channel 3: rcvd adjust 32768
debug2: channel 3: rcvd adjust 147456
debug2: channel 3: rcvd adjust 55788
debug2: channel 3: window 32740 sent adjust 32796
client:
ssh -Xvvv USERNAME@SERVER_IP mousepad
OpenSSH_6.1p1, OpenSSL 1.0.1c 10 May 2012
debug1: Reading configuration data /etc/ssh/ssh_config
debug2: ssh_connect: needpriv 0
debug1: Connecting to SERVER_IP [SERVER_IP] port 22.
debug1: Connection established.
debug1: identity file /home/USERNAME/.ssh/id_rsa type -1
debug1: identity file /home/USERNAME/.ssh/id_rsa-cert type -1
debug1: identity file /home/USERNAME/.ssh/id_dsa type 2
debug1: identity file /home/USERNAME/.ssh/id_dsa-cert type -1
debug1: identity file /home/USERNAME/.ssh/id_ecdsa type -1
debug1: identity file /home/USERNAME/.ssh/id_ecdsa-cert type -1
debug1: Remote protocol version 2.0, remote software version OpenSSH_6.1
debug1: match: OpenSSH_6.1 pat OpenSSH*
debug1: Enabling compatibility mode for protocol 2.0
debug1: Local version string SSH-2.0-OpenSSH_6.1
debug2: fd 3 setting O_NONBLOCK
debug3: load_hostkeys: loading entries for host "SERVER_IP" from file "/home/USERNAME/.ssh/known_hosts"
debug3: load_hostkeys: found key type ECDSA in file /home/USERNAME/.ssh/known_hosts:4
debug3: load_hostkeys: loaded 1 keys
debug3: order_hostkeyalgs: prefer hostkeyalgs: [email protected],[email protected],[email protected],ecdsa-sha2-nistp256,ecdsa-sha2-nistp384,ecdsa-sha2-nistp521
debug1: SSH2_MSG_KEXINIT sent
debug1: SSH2_MSG_KEXINIT received
debug2: kex_parse_kexinit: ecdh-sha2-nistp256,ecdh-sha2-nistp384,ecdh-sha2-nistp521,diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1
debug2: kex_parse_kexinit: [email protected],[email protected],[email protected],ecdsa-sha2-nistp256,ecdsa-sha2-nistp384,ecdsa-sha2-nistp521,[email protected],[email protected],[email protected],[email protected],ssh-rsa,ssh-dss
debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected]
debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected]
debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-512,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96
debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-512,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96
debug2: kex_parse_kexinit: none,[email protected],zlib
debug2: kex_parse_kexinit: none,[email protected],zlib
debug2: kex_parse_kexinit:
debug2: kex_parse_kexinit:
debug2: kex_parse_kexinit: first_kex_follows 0
debug2: kex_parse_kexinit: reserved 0
debug2: kex_parse_kexinit: ecdh-sha2-nistp256,ecdh-sha2-nistp384,ecdh-sha2-nistp521,diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1
debug2: kex_parse_kexinit: ssh-rsa,ssh-dss,ecdsa-sha2-nistp256
debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected]
debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected]
debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-512,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96
debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-512,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96
debug2: kex_parse_kexinit: none,[email protected]
debug2: kex_parse_kexinit: none,[email protected]
debug2: kex_parse_kexinit:
debug2: kex_parse_kexinit:
debug2: kex_parse_kexinit: first_kex_follows 0
debug2: kex_parse_kexinit: reserved 0
debug2: mac_setup: found hmac-md5
debug1: kex: server->client aes128-ctr hmac-md5 none
debug2: mac_setup: found hmac-md5
debug1: kex: client->server aes128-ctr hmac-md5 none
debug1: sending SSH2_MSG_KEX_ECDH_INIT
debug1: expecting SSH2_MSG_KEX_ECDH_REPLY
debug1: Server host key: ECDSA ABC123...
debug3: load_hostkeys: loading entries for host "SERVER_IP" from file "/home/USERNAME/.ssh/known_hosts"
debug3: load_hostkeys: found key type ECDSA in file /home/USERNAME/.ssh/known_hosts:4
debug3: load_hostkeys: loaded 1 keys
debug1: Host 'SERVER_IP' is known and matches the ECDSA host key.
debug1: Found key in /home/USERNAME/.ssh/known_hosts:4
debug1: ssh_ecdsa_verify: signature correct
debug2: kex_derive_keys
debug2: set_newkeys: mode 1
debug1: SSH2_MSG_NEWKEYS sent
debug1: expecting SSH2_MSG_NEWKEYS
debug2: set_newkeys: mode 0
debug1: SSH2_MSG_NEWKEYS received
debug1: Roaming not allowed by server
debug1: SSH2_MSG_SERVICE_REQUEST sent
debug2: service_accept: ssh-userauth
debug1: SSH2_MSG_SERVICE_ACCEPT received
debug2: key: /home/USERNAME/.ssh/id_rsa ((nil))
debug2: key: /home/USERNAME/.ssh/id_dsa (0x)
debug2: key: /home/USERNAME/.ssh/id_ecdsa ((nil))
debug1: Authentications that can continue: publickey,password
debug3: start over, passed a different list publickey,password
debug3: preferred publickey,keyboard-interactive,password
debug3: authmethod_lookup publickey
debug3: remaining preferred: keyboard-interactive,password
debug3: authmethod_is_enabled publickey
debug1: Next authentication method: publickey
debug1: Trying private key: /home/USERNAME/.ssh/id_rsa
debug3: no such identity: /home/USERNAME/.ssh/id_rsa
debug1: Offering DSA public key: /home/USERNAME/.ssh/id_dsa
debug3: send_pubkey_test
debug2: we sent a publickey packet, wait for reply
debug1: Authentications that can continue: publickey,password
debug1: Trying private key: /home/USERNAME/.ssh/id_ecdsa
debug3: no such identity: /home/USERNAME/.ssh/id_ecdsa
debug2: we did not send a packet, disable method
debug3: authmethod_lookup password
debug3: remaining preferred: ,password
debug3: authmethod_is_enabled password
debug1: Next authentication method: password
USERNAME@SERVER_IP's password:
debug3: packet_send2: adding 48 (len 68 padlen 12 extra_pad 64)
debug2: we sent a password packet, wait for reply
debug1: Authentication succeeded (password).
Authenticated to SERVER_IP ([SERVER_IP]:22).
debug1: channel 0: new [client-session]
debug3: ssh_session2_open: channel_new: 0
debug2: channel 0: send open
debug1: Requesting [email protected]
debug1: Entering interactive session.
debug2: callback start
debug2: x11_get_proto: /usr/bin/xauth -f /tmp/ssh-mHE6faU7YJF2/xauthfile generate :0 MIT-MAGIC-COOKIE-1 untrusted timeout 1200 2>/dev/null
debug2: x11_get_proto: /usr/bin/xauth -f /tmp/ssh-mHE6faU7YJF2/xauthfile list :0 2>/dev/null
debug1: Requesting X11 forwarding with authentication spoofing.
debug2: channel 0: request x11-req confirm 1
debug2: fd 3 setting TCP_NODELAY
debug3: packet_set_tos: set IP_TOS 0x10
debug2: client_session2_setup: id 0
debug1: Sending command: mousepad
debug2: channel 0: request exec confirm 1
debug2: callback done
debug2: channel 0: open confirm rwindow 0 rmax 32768
debug2: channel_input_status_confirm: type 99 id 0
debug2: X11 forwarding request accepted on channel 0
debug2: channel 0: rcvd adjust 2097152
debug2: channel_input_status_confirm: type 99 id 0
debug2: exec request accepted on channel 0
### After successful authentication, here above started the first waiting, where after first 1 min. continued with:
debug2: channel 0: rcvd ext data 210
debug2: channel 0: rcvd ext data 380
debug2: channel 0: rcvd ext data 121
debug3: Copy environment: XDG_SESSION_COOKIE=0d937ee20c7e42bdbf828421a30eaa2f-1357144247.348263-1841400888
debug3: Copy environment: XDG_SESSION_ID=5
debug3: Copy environment: XDG_RUNTIME_DIR=/run/user/1000
debug2: channel 0: written 711 to efd 6
### After another 1 min. continued with + started the app.
debug1: client_input_channel_open: ctype x11 rchan 3 win 65536 max 16384
debug1: client_request_x11: request from 127.0.0.1 46968
debug2: fd 7 setting O_NONBLOCK
debug3: fd 7 is O_NONBLOCK
debug1: channel 1: new [x11]
debug1: confirm x11
debug2: channel 0: rcvd ext data 62
Xlib: extension "RANDR" missing on display "localhost:10.0".
debug2: channel 0: written 62 to efd 6
debug1: client_input_channel_open: ctype x11 rchan 4 win 65536 max 16384
debug1: client_request_x11: request from 127.0.0.1 46972
debug2: fd 8 setting O_NONBLOCK
debug3: fd 8 is O_NONBLOCK
debug1: channel 2: new [x11]
debug1: confirm x11
debug2: channel 1: window 2045884 sent adjust 51268
debug2: channel 1: window 2031616 sent adjust 65536
debug2: channel 1: window 2031616 sent adjust 65536
debug2: channel 1: window 2031616 sent adjust 65536
debug2: channel 1: window 2031616 sent adjust 65536
debug2: channel 1: window 2031616 sent adjust 32768
debug2: channel 1: window 1949696 sent adjust 147456
debug2: channel 1: window 2041364 sent adjust 55788
debug2: channel 1: rcvd adjust 32796
debug1: client_input_channel_open: ctype x11 rchan 5 win 65536 max 16384
debug1: client_request_x11: request from 127.0.0.1 46974
debug2: fd 9 setting O_NONBLOCK
debug3: fd 9 is O_NONBLOCK
debug1: channel 3: new [x11]
debug1: confirm x11
debug2: channel 1: rcvd adjust 32800
It's quite strange, as I have no more ideas what to check next.
Any ideas pls?
thx in advance.

Have finally found a solution for this problem: http://serverfault.com/questions/490352 … w-to-start
Now the applications do start immediately via SSH X11 forwarding as expected.
The following three lines helped:
ip6tables -A INPUT -i lo -j ACCEPT
ip6tables -A OUTPUT -o lo -j ACCEPT
ip6tables -A FORWARD -i lo -o lo -j ACCEPT
While until now, all ip6 traffic has been forbidden (to drop all ip6 traffic) at the start of the system of course.
Nevertheless, I don't understand it, why the ip6 localhost has to be granted this way even if the /etc/ssh/sshd_config is configured for ip4 only "AddressFamily inet"?
I thought, that this way the sshd will be using ip4 protocol only (including for the X11 forwarding), then why does it still need the ip6?

Help! my macbook air (late 2008) takes too long to start up when i switch it on, what can i do to solve this problem?

the start up takes over 10min but after it starts up it works ok until i fix a usb to it then it starts to freeze every 2min. what can i do? please help me out. Thanks

Thanks for your response.
I have tried creating a new account but it didn't fix the problelm.
How do i safe boot?
when you say "safe booting" do you mean restarting/shutdown and restart? because i restarted my macbook air while holding down the shift key while it was starting up but there was not luck either, the problem was still there when i restarted it again.

Having lagging problems with YouTube videos, it simply takes so long for the red bar to completely load and the videos frequently pause and take too long to restart playing again.

I have been having lagging problems with YouTube videos for a number of months now. It simply takes so long for the red bar to completely load and the videos frequently pause and take too long to restart playing again. Even with little 2 and 3 minute videos.
I have a fast computer and my webpages load really, really fast. I have FireFox 4 browser and a Vista Home Premium 64-bit OS. So I don't have a slow computer or web browser. But these slow YouTube vids take way too long to load for some reason.
Does anyone have any idea how I can speed up YouTube?

Hi
The forums are customer to customer in the first instance, Only the mods (BT) will ask for personal information through a email link. Would you mind posting your Hub stats & BT speed test results this will help all with diagnosis-
To post the full stats from your router
for home hub - 192.168.1.254
Navigate to ADSL Settings or use the A-Z at the top right
Click on More Details and then post the results.
Run BT speed tester and post the results from http://speedtester.bt.com/
If possible it would be best to connect to the BT master socket this will rule out any telephone/broadband extension wiring also consider the housing of the hub/router as anything electrical can cause problems as these are your responsibility, if these are found to be the case Openreach (engineer) will charge BT Broadband, which will be passed onto you, around £130.00.
Noisy line! When making telephone calls, if so this is not good for your broadband, you can check-
Quite line test dial 17070 option 2 and listen - should hear nothing best done with old type analogue phone digital (dect) will do but may have slight hiss If you hear noise- crackling pops etc, report it as a noisy line on your phone, don’t mention broadband, Bt Faults on 151.
As for your FTTC its available in some areas between 40% & 80% of customers in enabled areas can receive it!
Mortgage Advisor 2000-2008
Green Energy Advisor 2008-2010
Charity Health Care Provider Advisor 2010-
I'm alright Jack....

Page takes too long to load because of videos

Hi. I have a website that I made, but the page takes too long to load because there are videos on it. Is there any way to stop the videos from auto-loading and instead only load when someone clicks on them to play?

There are several ways to have videos on a page without having them load until they are selected to play. A couple are:
1 - Opening Item in a New, Precisely Sized Window. This test site has 9 videos on the page: PhotoPresenter Animated Slideshow Themes.
2 - QT Movies via Export for Web in QT Player. This method is more difficult to implement.
OT

Takes too long buffering on you tube, cannot see some videos at all.

Takes too long buffering on Youtube, cannot see some videos at all. Have gone out of youtube and come back in again. have restarted the computer several times. Have come back later and tried again with the same results.

I don't have this problem - but a bunch of other people have youtube problems since upgrading to Yosemite.Yosemite 10.10.1 causing Safari not to play YouTube videos...

ITunes 7.6 No Audio When Playing a Music Video or Movie

I just installed iTunes 7.6.0.29 (It was released today).
There is no audio when playing a music video or a movie that I've purchased. Movie trailers and music videos in the iTunes store have no audio either. Videos from iTunes University that I've downloaded (such as an MIT lecture) play fine w/ audio.
Music audio (such as tracks I've purchased or tracks on the iTunes store) play fine.
QuickTime videos, such as a QT video on my desktop play fine. Windows Media Player works fine too.
So, why don't music videos and movies play (w/audio) on iTunes 7.6??

I'm experiencing what appears to be the exact same issue. I just installed iTunes 7.6.
Video but no audio:
Purchased iTunes TV episodes
Streamed video trailers in the iTunes Store
Works fine:
All music files, including protected files purchased through iTunes
The standalone Quicktime player performs normally with MOV files. Windows Media Player still performs normally.
I found an old support doc complaining of a similar issue with a previous iTunes release and tried the suggested fix: Uninstalling Quicktime and reinstalling it using the standalone installer (Quicktime 7.4). I also reinstalled iTunes. Neither solved the issue.
I'm very disappointed that I can no longer access the files I've purchased. I hope this is fixed very soon.

Ipod takes too long to connect

I just bought an 80 gb 5.5 gen ipod last week and everything was great, but now when i plug it into the PC it takes too long to detect it as a disc drive and once i open the itunes it takes too long to show the info i have stored, and sometimes only shows the music folder (no movies, tvshows, podcasts, etc) Is something wrong with my ipod?
Maybe is because of the songs and videos i already have... but i have more than 60 gb free.
It has also crashed twice while using the search feature, it just resets for itself.
Windows XP Pro 1.5 Ghz, 512 mb RAM

Alright so I found the answer to part of my question just now. Thinking when I first got my iPod Touch, I remembered that backups weren't as long. Then I thought to when things started getting worst, and I figured out that it started when I put too many apps on my iPod. So i removed all of them and my backup was the fastest I've seen in a while. Then I just but back the ones I really wanted and everything seems fine....for now.

AME CS6 rendering with AE and Pr takes too long

Hi Guys,
Need some help here. i have rendered a 30 secs mp4 video with 1920 x 1080 HD format 25 frames w/o scripting in AME for 4 hours!
Why does it take too long? I have rendered a 2 minute video with same format w/ scripting but only spare less than 30 minutes for rendering.
Im using After Effects and Premium Pro both CS6 and using Dynamic Link in AME.
What seems to be wrong in my current settings?
Any help would be appreciated.
Thanks!

This may be a waste of time, but it won't take a minute and is something you should always do whenever things go strangely wrong ............ trash the preferences, assuming you haven't done it already.
Many weird things happen as a result of corrupt preferences which can create a vast range of different symptoms, so whenever FCP X stops working properly in any way, trashing the preferences should be the first thing you do using this free app.
http://www.digitalrebellion.com/prefman/
Shut down FCP X, open PreferenceManager and in the window that appears:-
1. Ensure that only FCP X is selected.
2. Click Trash
The job is done instantly and you can re-open FCP X.
There is absolutely no danger in trashing preferences and you can do it as often as you like.
The preferences are kept separately from FCP X and if there aren't any when FCP X opens it automatically creates new ones . . . instantly.

Can't play youtube music videos on facebook

hi everyone, i was wondering, am i the only person who can't play music-videos from youtube - on facebook? i don't have this problem on chrome [which belongs to google, and so is youtube..]
it started in the last few days, or weeks, before i updated my firefox. i can't play youtube music-videos posted on facebook from facebook, but i can play them only from youtube.com.
when i try to play a video that has music in it, i get this message:
"this video contains content from RECORDLABEL. it is restricted from playback on certain sites. watch on youtube"
i also sometimes get a message that a certain video can't be played from playlists, but i can watch the video from its page [i don't know if it's related..].
my friends who use chrome can play music-videos on facebook, and i tried for myself and it plays the videos and doesn't show any restrictions messages.
i didn't try on explorer [bleh] or opera.
so my question again is, do you have the same problem too?
i can play this video on facebook: [it's funny as hell, watch it!]
http://www.youtube.com/watch?v=717vb7kLKKk
but i can't play this one on facebook, only on youtube: [and other music-videos, i can give you a million examples]
http://www.youtube.com/watch?v=eP-c2E1j8Qo
thanks :]

"11 people have this problem", hm... maybe i should try from a different computer. any ideas what might be the problem? if it's because of an addon i have, country, anything?

Can't play purchased music videos on my IPad

I've purchased a number of American Idol music videos via ITunes. However they will not show up nor play on my IPad. I just switched over to ICloud and still can't access or play my music videos. They play fine on my PC monitor. Any suggestions? I work in hospice and would like to share some of the music videos with my patients.

I do too. I get this image.

HT1386 copying files in itunes takes too long

When I drag music files into the iPhone's playlist, the copying takes too long. I am running 11 and have a 4

Wait on the update to finish downloading and installing.
If the device is in recovery mode there is really nothing that can be done besides restoring it.

Why does iPhone videos take so long to come up on the Apple TV?

Why does iphone videos take so long to come up on the apple tv?
1080P has a large file size but are there ways to get it to start to play faster?
Hard wiring it into the LAN helped a bit but what is really slowing it down? WPA2?
Thanks,

could be the wifi speed as in 56Mbit vs. newer 300Mbit version
or interfearing from other wifi networks which use the same channel
or microwave or dect phones which also operate on the 2.4Ghz band

Sometimes my computer takes too long to connect to new website. I am running a pretty powerful work program at same time, what is the best solution? Upgrading speed from cable network, is it a hard drive issue? do I need to "clean out" the computer?

Many times my computer takes too long to connect to new website. I have wireless internet (time capsule) and I am running a pretty powerful real time financial work program at same time, what is the best solution? Upgrading speed from cable network? is it a hard drive issue? do I only need to "clean out" the computer? Or all of the above...not to computer saavy. It is a Macbook Pro osx 10.6.8 (late 2010).

Almost certainly none of the above! Try each of the following in this order:
Select 'Reset Safari' from the Safari menu.
Close down Safari; move <home>/Library/Caches/com.apple.Safari/Cache.db to the trash; restart Safari.
Change the DNS servers in your network settings to use the OpenDNS servers: 208.67.222.222 and 208.67.220.220
Turn off DNS pre-fetching by entering the following command in Terminal and restarting Safari:
defaults write com.apple.safari WebKitDNSPrefetchingEnabled -boolean false

Playing a Music Video takes too long to start

Similar Messages

Maybe you are looking for