Playstation 3 nat problems fix BT hub

The problem is with online gaming on the ps3 where the nat is set to "moderate" rather than "open".
First access you hub settings by typing in 192.168.1.254 then settings/advanced settings/application sharing now with your ps3 turned on select playstation 3 from the game/application menu select it and also select its address from the device menu...apply.
Now the next bit is up to you as I'm no internet security expert but it seems to keep the nat in "open" state.... from application sharing under advanced settings select firewall and disable it then apply.
Now go back to the most overrated game in history...black ops and your nat should be open - this seems to work for most.

Your connection is Openreach Modem -> BT Home Hub 5 -> iMAC.
After a bit of reading - http://www.broadbandchoices.co.uk/guides/hardware/bt-home-hub
Openreach Modem - Optical Network Terminal (ONT).
HH5 - is a 4-port Ethernet Router/Switch
It looks like BT may be locking the MAC addresses of the modem and hh5 with access control lists, so customers cannot connect a device to replace the HH5.
You have an option. Connect one of the HH5 LAN ports to the WAN port of the Airport.
Set the Airport to Bridge mode, no DHCP address distribution, Create a Wireless Network.
You can just ignore the HH5 SSID(s) completely and just connect to the ones you create on the Extreme. The iMac can connect to any LAN port on the Extreme or one of the remaining HH5 LAN ports.
The only challenge you may have is, if the number of IP addresses the HH5 can allocate is limited to 4 (by BT's configuration). It can be verified using more than four (4) devices.
If this works, then there are alternatives where a new LAN within a LAN can be created if the IP address limitation becomes an issue.

Similar Messages

Azureus Nat problem

Hey
I am running a 17 inch imac and experiencing some trouble with my bittorrent client Azureus.
I simply never get the green smiley face. I read the wipi-help from Azureus and confirmed by using their instructions that I do have a NAT problem. I have no firewall running. I did continue reading the explanation in the Wiki but it seems to be PC oriented. Can anybody give me some good info to fix this problem?
By the way will my downloads be faster when I do use a correctly configured NAT?
Samuel
PS I am not using a router just a ADSL Modem

I had the same problem but turned off my firewall, opened the port 59981, turned my firewall back on & it worked straightaway, my d/l speed shot up frpom 20kb to 280kb. My only problem now is that when I am running azereus my internet connection sometimes drops and the only way round it seems to be turning off my mac & cable modem and rebooting. I'm on Telewest Blueyonder cable with a webstar cable modem and it only happens when I'm using Azereus.
Very frustrating!!

Open NAT problems with Xbox One .

When I first got my 1900ac I used Media Priortization to get an open NAT for Call of Duty Advanced Warfare on my Xbox One ; prioritizing the Xbox . It worked fine for about 6 months until I changed cable/net provider to Nextech in Ks. This company uses the 1900ac to hook up it's system for all it's customers ( since I already had one they're using mine ). Unfortunately I'm unable to get an open NAT in this game anymore ; I've tried just about everything , NAT forwarding , triggering , Media Prioritization . Nextech support & Xbox Live support , useless . Tried Portforward . com , nothing . Forwarding port 53 cuts off net connection & doing the static ip change for Xbox didn't help . Almost everything I've looked at seems out of date & I'm at my wits end . It would seem by now Linksys should have solutions available , any ideas ?

Thank you chin_pamz13 for your response . I tried to check if my modem had a public or private ip address but I'm not sure how to do that ; I've read about double NAT's elsewhere . Regardless , I think I've finally found a solution that seems to be working so far . I went to the website " tech - recipes . com " & found an article , " Xbox One open NAT " by Aaron St. Clair . I tried his first suggestion about port triggering , with extra ports I had'nt seen before . That did not work for me so I followed his instructions for putting the Xbox in the DMZ & it's working ! I think my problems from before were the result of improperly setting up the static ip address for my router & Xbox . Previous instructions had me changing the ip in the console along with the router ; Aaron said not to do so in the Xbox , let the router do the work it's supposed to do & make sure the settings in the console are on automatic . In the router at the DMZ , I was'nt sure how to proceed , but at the bottom is a section labeled DHCP reservations list ; clicked on that , saw XboxOne , clicked on that & it filled out the MAC address above for me . Then I went to the Xbox network settings , advanced settings & clicked " automatic " at ip address , subnet & DNS . I checked mutiplayer connections & did the " hold bumper & trigger buttons " trick & finally got an open NAT ; fired up CoD Advanced Warfare & got the open NAT there also . I may have screwed up when I did the port triggering but since the DMZ fix seems to work I'm going to leave things alone . Hope this helps others with open NAT problems .

WRT120N Xbox Nat Problems Again

Yes, somebody else is posting about getting that stupid NAT open on Xbox Live. If any of the solutions posted so far helped I wouldn't be the 1987th person asking.
This is my third router I've used with my xbox over the years. This is not my first rodeo with this problem. I know about the port forwarding, mtu, static IPs, firmware updating, etc. I've done it all several times over. Normally I'd be the one helping somebody else get this problem fixed for them. But for some reason, with this WRT120N router, I've sat here for 8 hours pulling my hair out trying to get this thing working. No matter what I do this NAT won't open. I'm out of ideas and looking for more, please.

Try to reflash the same firmware on your router...reser the router for 30 seconds and reconfigure it from the scratch...
As your Internet Service Providor is Cable follow this link to reconfigure the router.
For the X-Box, try this :
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
On the set-up tab change the MTU Size to 1365 and click Save Settings...
Click on "Administration" tab and disable the option UPnP and click Save Settings...
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 53 and End box type in 3074, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box, click Save Settings once done...
2) Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
3)Click on the Status tab and take note of DNS1 and DNS2 Addresses...
4) Goto the XBox Network Settings and IP Address Settings and select manual IP Settings and assign the following on your Xbox
IP Address :- 192.168.1.20, Subnet Mask :- 255.255.255.0, Default Gateway :- 192.168.1.1...
5) Also assign the DNS Addresses on the Xbox
Use DNS1 and DNS2 Addresses you took note off of the router status tab as Primary DNS & Secondary DNS for the xbox...
6) Turn off your modem, router, and Xbox...Wait for a minute...
7) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the Xbox and test it...it will connect...

Does Mavericks have the problem fixed with working with the Dell UltraSharp U3014 30 inch monitor?

Does Mavericks have the problem fixed with working with the Dell UltraSharp U3014 30 inch monitor?

I have this (or a similar) issue and I did notice something interesting. After I boot into Windows via Bootcamp (where I have the U3014 specfic driver installed) and then reboot into MacOS X (Mavericks) the monitor works flawlessly.
I would hazard a guess that this means bootcamp is retaining the driver used in Windows. Kind of the reverse of the TB GBE adapter driver issue.
To explain my issue for anyone else: the monitor flicks on and off as if the connection was poor. Connecting via HDMI. Connection is fine and as stated, everything works fine in Bootcamp.

I have problem " verify your emal " i can't change account , i removed application and instell again , same problem fix email and " verify email"

i have problem " verify your emal " i can't change account , i removed application and instell again , same problem fix email and " verify email"

The Email ID provided here has CC registered to it in active status. The Email also stands verified. Are you using any other Email ID ?
Let me know if you are facing issue regarding verification by activating the Cc with the email ID provided here.
Regards
Rajshree

Ps3 nat problem

why cant u get a open nat with ps3 always on moderate how do u get it to open ?

This link should help.
NAT Problems on games consoles and computers
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

HT3552 I am billed 3 times for a same item. How can I get the problem fixed? Thanks a lot for your help.

I am billed 3 times for a same item. How can I get the problem fixed? Thanks a lot for yur help. nhuttan448

Go here:
http://www.apple.com/support/itunes/contact/
and follow the instructions to report the issue to the iTunes Store.
Regards.

Xbox360 WRT54GS ver. 6 NAT problems

my xbox 360's NAT is set to strict and prevens me from connecting with a lot of otehr players and my wireless router is a WRT54GS ver. 6

for xbox 360 having NAT problem... you need to call Xbox to ask for the port numbers to open...now if your isp is dsl then call them up and set the modem to bridge to set the rtr to pppoe...in this way we will be able eliminate the multiple NAT issues and for your xbox to work...
CamZ

Route or NAT problem?

Hi Everyone,
We have an ASA 5540 at our data center, with ASA 5505's at most remote sites.
At the sites without layer 3 switches behind the ASA 5505's, we can't reach the data center internal network through the ASA for flow-export, etc.
So, what I'm basically saying is, even though the tunnel is up and everything behind the branch ASA can reach the data center networks fine, the ASA itself cannot reach hosts on the data center network.
I'm hoping to configure these ASA 5505's so I can do flow export and SNMP logging from them, but without this routing or nat problem resolved, they just won't do it.
Doing a packet tracer from the ASA 5505 to the data center server I'm most focused on, reveals this:
BRANCH5505f01# packet input inside icmp 10.15.16.1 8 0 10.1.1.15 detailed
Phase: 1
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
Forward Flow based lookup yields rule:
in id=0xcb0b6698, priority=1, domain=permit, deny=false
        hits=1004755, user_data=0x0, cs_id=0x0, l3_type=0x8
        src mac=0000.0000.0000, mask=0000.0000.0000
        dst mac=0000.0000.0000, mask=0100.0000.0000
        input_ifc=inside, output_ifc=any
Phase: 2
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   10.1.1.15       255.255.255.255 outside
Phase: 3
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   0.0.0.0         0.0.0.0         outside
Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: outside
output-status: up
output-line-status: up
Action: drop
Drop-reason: (rpf-violated) Reverse-path verify failed
I am thinking the problem is NAT related, but with the new ASA NAT rule format due to v9.1... struggling to get a grip on where it is... any thoughts/help are appreciated.
Ken
Here is the relevant config for the Branch ASA and also the relevant config from the data center ASA:
Branch ASA Config Parts:
: Saved
ASA Version 9.1(2)
hostname BRANCHASA5505
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
speed 100
duplex full
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
description LAN_NETWORK
nameif inside
security-level 100
ip address 10.15.6.1 255.255.254.0
interface Vlan2
nameif outside
security-level 0
ip address <outside ip> 255.255.255.248
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object-group network BRANCH_NETWORKS
description BRANCH LOCAL NETWORKS
network-object 10.15.6.0 255.255.254.0
object-group network LAN_NETWORKS
network-object 10.0.0.0 255.0.0.0
network-object 134.200.131.0 255.255.255.0
network-object 134.200.220.0 255.255.255.0
network-object 134.201.2.0 255.255.255.0
network-object 163.243.195.0 255.255.255.0
network-object 172.16.0.0 255.240.0.0
network-object 192.168.0.0 255.255.0.0
network-object 10.1.3.0 255.255.255.0
network-object 10.31.2.0 255.255.255.0
network-object 10.1.1.0 255.255.255.0
network-object 172.26.1.0 255.255.255.0
object-group network NETWORK_MGMT
network-object 10.0.0.0 255.0.0.0
access-list DATACENTER_VPN_ACL remark *******************************************************************
access-list DATACENTER_VPN_ACL remark * FOR VPN CONNECTION TO DATACENTER/VEYANCE NETWORKS *
access-list DATACENTER_VPN_ACL remark *******************************************************************
access-list DATACENTER_VPN_ACL extended permit ip host <outside ip> host <outside ip datacenter asa>
access-list DATACENTER_VPN_ACL extended permit ip object-group BRANCH_NETWORKS object-group LAN_NETWORKS
access-list INSIDE_NONAT extended permit ip object-group BRANCH_NETWORKS object-group LAN_NETWORKS
access-list INSIDE_FILTER extended permit tcp any4 any4 eq www
access-list INSIDE_FILTER extended permit tcp any4 any4 eq 8080
logging host inside 10.1.1.15
flow-export destination inside 10.1.1.15 2055
ip verify reverse-path interface inside
ip verify reverse-path interface outside
nat (inside,outside) source static LAN_NETWORKS LAN_NETWORKS destination static BRANCH_NETWORKS BRANCH_NETWORKS route-lookup
nat (inside,outside) source static BRANCH_NETWORKS BRANCH_NETWORKS destination static NETWORK_MGMT NETWORK_MGMT route-lookup
nat (inside,outside) source dynamic any interface
object network obj_any
nat (inside,outside) dynamic interface
access-group FROM_OUTSIDE in interface outside
route outside 0.0.0.0 0.0.0.0 <outside ip gateway> 1
route outside 10.1.1.15 255.255.255.255 <outside ip datacenter asa> 1
management-access inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
tunnel-group <outside ip datacenter asa> type ipsec-l2l
tunnel-group <outside ip datacenter asa> ipsec-attributes
ikev1 pre-shared-key *****
class-map type regex match-any DomainBlockList
match regex DomainList-Netflix
class-map type inspect http match-all BlockDomainsClass
match request header host regex class DomainBlockList
class-map inspection_default
match default-inspection-traffic
class-map httptraffic
match access-list INSIDE_FILTER
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map type inspect http http_inspection_policy
parameters
protocol-violation action log
class BlockDomainsClass
reset log
policy-map URL-filter-policy
class httptraffic
inspect http http_inspection_policy
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect http
class class-default
flow-export event-type all destination 10.1.1.15
service-policy URL-filter-policy interface inside
prompt hostname context
Datacenter ASA Config Parts:
ASA Version 9.0(1)
hostname DATACENTERASA5540
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
names
interface GigabitEthernet0/0
description *** TO OUTSIDE NETWORK AT DATACENTER ***
speed 100
duplex full
nameif OUTSIDE
security-level 0
ip address <outside ip>
interface GigabitEthernet0/1
description *** TO INSIDE NETWORK ***
nameif INSIDE
security-level 100
ip address 10.1.3.2 255.255.255.0
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group network LAN_NETWORKS
network-object 10.0.0.0 255.0.0.0
network-object 134.200.131.0 255.255.255.0
network-object 134.200.220.0 255.255.255.0
network-object 134.201.2.0 255.255.255.0
network-object 163.243.195.0 255.255.255.0
network-object 172.16.0.0 255.240.0.0
network-object 192.168.0.0 255.255.0.0
network-object 10.1.3.0 255.255.255.0
network-object 10.31.2.0 255.255.255.0
network-object 10.1.1.0 255.255.255.0
network-object 172.26.1.0 255.255.255.0
object-group network DATACENTER_NETWORKS
network-object 10.1.0.0 255.255.0.0
object-group network BRANCH_NETWORKS
network-object 10.15.6.0 255.255.254.0
access-list BRANCH_VPN_ACL remark ****************************************************
access-list BRANCH_VPN_ACL remark * FOR SITE TO SITE VPN TO BRANCH WV USA *
access-list BRANCH_VPN_ACL remark ****************************************************
access-list BRANCH_VPN_ACL extended permit ip host <outside ip> host <outside ip branch asa>
access-list BRANCH_VPN_ACL extended permit ip object-group LAN_NETWORKS object-group BRANCH_NETWORKS
flow-export destination INSIDE 10.1.1.15 2055
flow-export template timeout-rate 1
flow-export delay flow-create 180
ip verify reverse-path interface OUTSIDE
ip verify reverse-path interface INSIDE
no failover
nat (INSIDE,OUTSIDE) source static LAN_NETWORKS LAN_NETWORKS destination static BRANCH_NETWORKS BRANCH_NETWORKS route-lookup
access-group FROM_OUTSIDE in interface OUTSIDE
route OUTSIDE 0.0.0.0 0.0.0.0 <outside ip> 1
route INSIDE 10.0.0.0 255.0.0.0 10.1.3.1 1
route OUTSIDE 10.15.6.0 255.255.254.0 <outside ip branch asa> 1
crypto map OUTSIDE-MAP 156 match address BRANCH_VPN_ACL
crypto map OUTSIDE-MAP 156 set pfs
crypto map OUTSIDE-MAP 156 set peer <outside ip branch asa>
crypto map OUTSIDE-MAP 156 set ikev1 transform-set ESP-3DES-MD5 ESP-3DES-SHA
tunnel-group <outside ip branch asa> type ipsec-l2l
tunnel-group <outside ip branch asa> ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
class class-default
flow-export event-type all destination 10.1.1.15
user-statistics accounting
service-policy global_policy global
smtp-server 172.19.1.137
prompt hostname context
call-home reporting anonymous
Again, any help you can provide is appreciated... will vote for best...

I ran it, with the source IP corrected (it is 10.15.6.2):
BRANCHASA# packet input inside icmp 10.15.6.2 8 0 10.1.1.15 detailed
Phase: 1
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
Forward Flow based lookup yields rule:
in id=0xcb0b6698, priority=1, domain=permit, deny=false
        hits=1203279, user_data=0x0, cs_id=0x0, l3_type=0x8
        src mac=0000.0000.0000, mask=0000.0000.0000
        dst mac=0000.0000.0000, mask=0100.0000.0000
        input_ifc=inside, output_ifc=any
Phase: 2
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   0.0.0.0         0.0.0.0         outside
Phase: 3
Type: UN-NAT
Subtype: static
Result: ALLOW
Config:
nat (inside,outside) source static BRANCH_NETWORKS BRANCH_NETWORKS destination static NETWORK_MGMT NETWORK_MGMT route-lookup
Additional Information:
NAT divert to egress interface outside
Untranslate 10.1.1.15/0 to 10.1.1.15/0
Phase: 4
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   10.15.6.0       255.255.254.0   inside
Phase: 5
Type: NAT
Subtype:
Result: ALLOW
Config:
nat (inside,outside) source static BRANCH_NETWORKS BRANCH_NETWORKS destination static NETWORK_MGMT NETWORK_MGMT route-lookup
Additional Information:
Static translate 10.15.6.2/0 to 10.15.6.2/0
Forward Flow based lookup yields rule:
in id=0xcb12f2f0, priority=6, domain=nat, deny=false
        hits=15824, user_data=0xcb0fdef8, cs_id=0x0, flags=0x0, protocol=0
        src ip/id=10.15.6.0, mask=255.255.254.0, port=0, tag=0
        dst ip/id=10.0.0.0, mask=255.0.0.0, port=0, tag=0, dscp=0x0
        input_ifc=inside, output_ifc=outside
Phase: 6
Type: NAT
Subtype: per-session
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0xcaa712e0, priority=0, domain=nat-per-session, deny=true
        hits=77610, user_data=0x0, cs_id=0x0, reverse, use_real_addr, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=0
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=0, dscp=0x0
        input_ifc=any, output_ifc=any
Phase: 7
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0xcb0bc128, priority=0, domain=inspect-ip-options, deny=true
        hits=91404, user_data=0x0, cs_id=0x0, reverse, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=0
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=0, dscp=0x0
        input_ifc=inside, output_ifc=any
Phase: 8
Type: INSPECT
Subtype: np-inspect
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0xcb0bbc28, priority=66, domain=inspect-icmp-error, deny=false
        hits=4585, user_data=0xcb0bb238, cs_id=0x0, use_real_addr, flags=0x0, protocol=1
        src ip/id=0.0.0.0, mask=0.0.0.0, icmp-type=0, tag=0
        dst ip/id=0.0.0.0, mask=0.0.0.0, icmp-code=0, tag=0, dscp=0x0
        input_ifc=inside, output_ifc=any
Phase: 9
Type: VPN
Subtype: encrypt
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
out id=0xcb0c1218, priority=70, domain=encrypt, deny=false
        hits=708, user_data=0xbf63c, cs_id=0xcb9ad918, reverse, flags=0x0, protocol=0
        src ip/id=10.15.6.0, mask=255.255.254.0, port=0, tag=0
        dst ip/id=10.0.0.0, mask=255.0.0.0, port=0, tag=0, dscp=0x0
        input_ifc=any, output_ifc=outside
Phase: 10
Type: NAT
Subtype: rpf-check
Result: ALLOW
Config:
nat (inside,outside) source static BRANCH_NETWORKS BRANCH_NETWORKS destination static NETWORK_MGMT NETWORK_MGMT route-lookup
Additional Information:
Forward Flow based lookup yields rule:
out id=0xcb12fb00, priority=6, domain=nat-reverse, deny=false
        hits=15837, user_data=0xcb124438, cs_id=0x0, use_real_addr, flags=0x0, protocol=0
        src ip/id=10.15.6.0, mask=255.255.254.0, port=0, tag=0
        dst ip/id=10.0.0.0, mask=255.0.0.0, port=0, tag=0, dscp=0x0
        input_ifc=inside, output_ifc=outside
Phase: 11
Type: FLOW-CREATION
Subtype:
Result: ALLOW
Config:
Additional Information:
New flow created with id 143081, packet dispatched to next module
Module information for forward flow ...
snp_fp_tracer_drop
snp_fp_inspect_ip_options
snp_fp_translate
snp_fp_adjacency
snp_fp_encrypt
snp_fp_fragment
snp_ifc_stat
Module information for reverse flow ...
Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: outside
output-status: up
output-line-status: up
Action: allow

ASA5512 iOS 9.3 inside nat problem

Hi,
I face some nat problem. i have ASA5512 iOS 9.3 its connect outside (ip: 37.10.1.2/29) for internet and inside (ip 10.78.61.1/24) for LAN and server.
I configure dynamic nat for internet its work. In LAN switch has 4 VLAN one server VLAN ip add 10.88.61.0/24.
Now i map a public ip 37.10.1.3 for server 10.88.61.10 from outside internet its work. But when i try to ping server public ip 37.10.1.3 from LAN its not ping but server local ip 10.88.61.10 ping from LAN.
How can solve the issue i need to ping public ip from LAN. ALL LAN VLAN are nat on ASA outside interface (ip: 37.10.1.2/29).
interface GigabitEthernet0/0
description #### Connect TO Internet ####
nameif outside
security-level 0
ip address 37.10.1.2 255.255.255.248
interface GigabitEthernet0/1
description #### Connect TO Core Switch ####
nameif inside
security-level 100
ip address 10.78.61.1 255.255.255.0
access-list outside-in extended permit ip any any
access-group outside-in in interface outside
access-group outside-in in interface inside
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network obj_Ser
host 10.88.61.10
object network obj_Ser_WAN
host 37.10.1.3
nat (inside,outside) source static obj_Ser obj_Ser_WAN
object network obj_any
nat (inside,outside) dynamic 37.10.1.4
same-security-traffic permit intra-interface
Thanks
Afzal

Hi,
Try this NAT:-
nat (inside,inside) source static obj_Ser obj_Ser_WAN
Thanks and Regards,
Vibhor Amrodia

Jumpy scrowl control with mouse.Only with Firefox, not Internet explorer. Problem fixed when I updated to 6. 0.2 but problems returned after about a week.. 0.2

Jumpy scroll wheel control with mouse. Only with Firefox, not Internet explorer.Even pushing the scroll wheel and trying to adjust for a smooth easy scroll the text stops and starts. Problem fixed itself when I updated to 6. 0.2 from an older version but the problem returned after about a week.. The problems go away when I go to web site and scroll but is back when I return to my home page (mozilla firefox)

Good post, and glad to hear you had a solid transition. Mine went well too, though I think I beat the rush.
It's worth noting that the vast and overwhelming majority of headaches people were experiencing were related to download and activation servers (as well as credit check servers for some mobile carriers) being crushed and overwhelmed.
To give you an idea of just how crushed, here are some numbers. In the last year, something in the neighborhood of 8 million iPhones have been sold. That's just shy of 22,000 per day. So the typical traffic is around 22,000 times a day, someone is hitting the server for update/activation.
This weekend, Apple sold 1 million iPhones. In other words, 333,333 phones per day. Holy crap!
As if that wasn't enough, there are 8 million of us out there with the first generation iPhone. Not only do we need to download the new firmware, but we have to install it. The installation process requires hitting the activation server again, to validate the phone. Mind you, not everybody upgraded this weekend, but a few million did. For the sake of argument, we'll assume that's 1 million a day. So, instead of the normall traffic of 22K phones a day, those activation servers got SLAMMED with 1.33 million activations per day.
It ***** that some people had delays and hiccups and a hard time and everything, but completely understandable. With luck things will run more smoothly from here on out.
Trilo

Nokia 6700 USB cable connectivity problem -fixed-

Ok, got my 6700 today. Everything worked like a charm, until I tried to connect it to my PC using the supplied USB cable. I downloaded and installed the latest Nokia PC suite which supports this phone (7.1.30.9) and connected the phone. Vista was unable to install a driver, and the phone was listed in the device manager as 'unknown usb device'. The phone display reported 'no response from host' after plugging in the usb cable.
I searched online for a solution, and tried the following:
- repaired the install of the Nokia connectivity cable driver: no success.
- deinstalled the nokia pc suite, ran the pc suite cleaner, rebooted and reinstalled the pc suite: no success.
- threw away the unknown usb device in the device manager and plugged the cable back in so that Vista would try to install the driver again: no success.
- tried other USB slots (not behind HUB): no success.
At this point I was so frustrated that I decided to take out the supplied 1gb micro sd card and transfer some data to it using a card reader. When I looked in the root of the sd card, I noticed that there was an executable called pc-suite.exe there, among some other files. I decided to delete those files to see if they were causing the problems, I deleted the following files:
- autorun.inf
- launcher.exe
- pc-suite.exe
- qf
Replaced the micro sd card in the phone, plugged in the usb cable and voila: connection! Everything worked like a charm.
During my online search I noticed I wasn't the only one experiencing connectivity problems with the 6700. Maybe this fix will help other people as well, that's why I decided to post it here. ;-)
Peter

Thanks Peter, nice job - same problem, your solution is working. Shame on Nokia - i have so many problems with E52, and now with 6700 - why ? Is it so difficult to make a reliable software ? So disappointed ... maybe Apple is the solution - but after 10 years with Nokia why change with Apple ?

Problem in translation hub

Hi to all, i am new to translation hub . i created a new project under newproject after that i used imported files and imported the some reports(.rex).i am not able to see the priview, when i am clikcing the prieview then i am getting the error. the error message is 'the instruction at "0x73dd1351" referenced memory at "0x00000004". the memory could not be "read" click on ok to terminate the program'
any body please suggest me how fix the problem. please help its very urgent.
Thanks&Regards
Srinivas

I suggest you call Oracle Support. They should be able to help you out.

Problem with usb hub 3.0 to connect printer and hd

Hello,
I have problems with using a usb 3.0 hub to connect a HD and a printer to my Time Capsule. HD is found and works properly. Printer is visible in programms but doesnot work.
How to fix this.
Ciao Pieter

OK, plug the hub back in with the printer.. delete the current setup on the computer and try reinstalling it.
But it tells you something if the printer is not recognised..
Why don't you just share it from the computer.. USB printer are not supposed to be plugged into a network device. They are designed as local printers.

Playstation 3 nat problems fix BT hub

Similar Messages

Maybe you are looking for