Please adjust base unit and coversion factor

Hello Frinds,
When I am going to change purchase info record, I am getting the error "Please adjust base unit and coversion factor". Base unit in info record and material master are same.
I don't understand reason for this error. can anybody help me to resolve this issue?
Thanks,
Bhairav

Hello Jürgen,Thanks for your reply.
I have checked the fields you said. In MARA it is showing base unit of measure as EA and where as in EINA it is showing base unit of measure as blank (no value).
How can we correct this issue? System keep on giving this error in ME13. System did not defualt EA in info record base unit of measure field.
Expecting your reply.
Thanks,
Bhairav
Edited by: Hari P Peddi on Jan 4, 2011 1:01 PM

Similar Messages

Diff bet Base Unit and Order Unit

Hi All,
I was going through the table MARA. I found tht there are two columns named 'Base Unit' n 'Order Unit'. I found interestingly that for couple of materials the units are diff in both coloumns (e.g: For a material Base Unit is EA but the Order unit is in KG). What is the diff bet Base unit and Order unit?
Please inform how is it possible to have two diff units for a single material??
Thanks in Adv.

Base Unit of measure is generally the smallest unit that can be used for a material.
But a company may never issue orders in this base unit.
So in the material master, order unit can be configured which may be separate then Base unit.
As a result orders will always will be placed in this unit.
For ex:
Base unit is set an Inch but the company always issues material always in foot.
Therefore in the material master Base unit of measure is set to Inch and Order Unit of measure is set to Foot

I just purchased an airport extreme router to increase the range of my wifi. I have an imac with 10.5.8. I get a flashing yellow light on the base unit and it tells me I need airport utility to install yhe ubnit. Where do I get this and how do I do it?

I just purchased an airport extreme router to increase the range of my wifi. I have an imac with 10.5.8. I get a flashing yellow light on the base unit and it tells me I need airport utility to install yhe ubnit. Where do I get this and how do I do it?

sylviafromhanover wrote:
So I assume that the original modem stays installed with the coaxial cable and the Exrtreme is in addition to that.
Yes, that is correct.
Did you have the instructions that came with your Airport Extreme? Are you sure you have it setup properly? Here is the setup guide:
http://manuals.info.apple.com/en/airportextreme_802.11n_userguide.pdf
Ensure you have everything setup properly. Once you do this and if you are still having trouble, follow Star's instructions.

BT 1500 base unit and 4500 handsets

Hi
Our BT studio 4500 base charging unit recently stopped working after a lightening storm. Not sure if the base unit itself was affected but without the functioning charging unit it's not possible to know.
Rather than replace the 4500 base unit and charger, I'd prefer to buy a single Studio 1500 base unit and use with the two remaining handsets from the 4500. Does anyone know if the two 4500 handsets (which appear to still function) would work with a BT Studio 1500 DECT base set.
Thanks

The fault must be in the main base unit then. Is the red answer machine light illuminated? If so the base has power, so unless there is a "dirty" connector for the phone I think you need to get a replacement.
It might be the plug in transformer - if you a "multi plug" transformer you could test for this.

I have Airport Extreme as the base unit and an Express unit in a room separated by a brick wall to improve signal. Express shows a green light indicating signal but my iPad does not perform well. How can I improve other than hardwire ethernet connection?

I have Airport Extreme as the base unit and an Express unit in a room separated by a brick wall to improve signal. Express shows a green light indicating signal but my iPad does not perform well. How can I improve other than hardwire ethernet connection?

Other suggestions, and more info about the nature of the problem, may be in this Apple tech note.
http://support.apple.com/kb/HT1365
For example, you might find that the brick wall is not the only problem. There may be other devices pumping out enough wireless interference to be making things even worse.
I agree with Bob Timmons that Ethernet is best and most reliable. And that powerline (which I use) is easier and potentially faster than wireless...but only if your power lines do not have electrical devices plugged in which produce electrical noise on the line. Powerline will be slower than Gigabit Ethernet.
Ethernet cable is the only way to ensure that the signal goes directly there in a shielded way for a clear fast signal. Wireless and powerline are much slower because of all the other things the signal has to fight past to get to the other device.

Requistion and Purchase Order - base unit and order unit

People,
I have a basic doubt in MM:
I have a Requisition with a item using the base unit, for instance 20 litres.
When I create a Purchase Order in ME21N passing the requisition and item number, I must be converted to the order unit, correct?
In this case, we have 1 UN (order unit) corresponds to 20Liters (base unit).
I did believe the Purchase would be converted to 1 UN, but I got 20 Liters.
What is correct?
Thanks a lot!

If you maintian the order unit in the mateiral master purchaisng screen than whenever you create the PO system will convenrt in to that order unit and in the Po item details you will see the conversion of base unit to order unit.
now suppose you have more than one order unit than you activate the Variable order unit in the material master and maintiqan the conversion of that and create the diff info record for diff order unit based on the vendor so whne oyu create the PO as per the vendor system will pull the order unit in the PO.
Hope this will give you clear picture.

I have an airport extreme base unit and utility can not find it

I have a 5th gen airport extreme router which works just fine with I plug in an ethernet cord to it … however when I want to use anything else (iPad, iPhone) my router is not showing up in any of the airport utility scans … my wife said yesterday it popped up a question and she either accepted it or said yes and since that point it has not shown up at all … on mac, pcs, iPad, iPhones nothing … I've even tried to do a hard factory restart of the base station and it still hasn't worked ... any ideas?

Hi wusid,
Thanks for using Apple Support Communities. This article has some steps to try if the Airport Extreme isn't appearing on your iOS devices:
AirPort base station doesn't appear in AirPort Utility 1.3 for iOS
http://support.apple.com/kb/TS4601
This article would be for troubleshooting on the Mac:
AirPort base station not seen or "An unexpected error occurred" appears in AirPort Utility 6.3
http://support.apple.com/kb/TS4597
Cheers,
- Ari

Cannot switch base units on Goods Receipt PO copied from Purchase Order

Hi,
I am wondering if there is a simple trick or setting for this or if we have to use a UDF/FMS...
When using Uom for sales and purchasing, you cannot switch between Yes and No for base units on the target document(GRPO) when copying a PO to GRPO.
For example, enter a purchase order selecting 'No' for base units and enter quantity 1 for item with Uom case(25 pcs in a case). 25 are ordered. If the warehouse receives 23 instead of a full case from the supplier, they want to be able to enter 23 on the GRPO(copied from PO). They don't want the warehouse staff calculating what percentage to put in for quantity (23/25 = 0.92), they would just like them to use the drop down box and change the base units to Yes and receive the quantity 23 units.
Any suggestions?

Hi,
How often this would happen? If it is very frequent, my suggestion would be considering it when you create PO. You know, if you could change that option, the link between PO and GRPO will be broken. It is not recommended.
Thanks,
Gordon

Cheking the material for base unit or convert it to base unit.

Hi friends,
I have a requirement asa follows.
I Have an internal table ITAB1 in that i have some 200 records. In that ITAB1 i have
MATNR and MEINS field and iam selecting those fields from MSEG table.
Now my requirment is i have to check for base unit of that particular.
example :
now let us say iam getting in my ITAB1.
MATNR      MEINS
M-123          EA
now i have to check the base material for that material. if both the base unit and what i got i same then its ok.        or    if the both are not same then it should convert to the base unit.
how can i do that.
Regards,
Priyanka.

Hi Priyanka,
To this FM u have to pass the material number, Input unit(itab1-meins), Output unit(Base unit-mara-meins), Quantity. In Importing parameter E_MENGE pass one variable. After FM call u will receive the converted value in this variable.
Just check the where used list of the FM to see the sample code.
    CALL FUNCTION 'MD_CONVERT_MATERIAL_UNIT'
         EXPORTING
              I_MATNR              = P_MATNR
              I_IN_ME              = P_MEEHT "Input unit
              I_OUT_ME             = P_AUSME "Base unit
              I_MENGE              = P_MENGE "Input Quantity
         IMPORTING
              E_MENGE              = I_AUMENGE "Quantity in base unit.
         EXCEPTIONS
              ERROR_IN_APPLICATION = 1
              OTHERS               = 2.
Thanks,
Vinod.

Views and Base unit of Measure is not coming in Chines Lang

HI All
Plz Help me.
I log-In Chines Server, during MM01 the views are coming in English language instead of chines.
and during PO creation The Base unit of Measure is not Coming in Chines Language it is displaying Some number??
I have maintained Source and taget lag in CUnI..but still Im getting this problem..
How to solve this plz help..
Thanks and regards
Ramesh reddy

Hi
Please maintain the translation in the Following Configuration
Logistics - General->Material Master->Configuring the Material Master->Define Structure of Data Screens for Each Screen Sequence
Select the Specific Screen Sequence & Maintain the languages
Similarly please maintain the Translations in the Transaction CUNI for the Base UOM in respective languages
I hope currently in your system only Language EN is maintained
Thanks
Madhav

Units of measure and conversion factor

while executing a session, I get the message 'Please check units of measure and conversion factor', what does it indicate? there are fields like order unit, conversion (purchasing) in creating info records transaction ME11.

in bdc when ever u r working with quantity and price fields it is better to move this fields in to string and do the concatenation kind of stuff..............
reward points if helpful................

Creating info records: units of measure and conversion factor

while executing the session, I get the message 'Please check units of measure and conversion factor', what does it indicate?

resolved

Material Master MATMAS IDOC and base unit of measurement

Hi
We are using SAP standard material master IDOC type MATMAS05 to trigger IDOC. Our material master is having base unit of measure as "G". We are not using ISO unit of measurement. But Material master IDOC, segment E1MARM is populating base unit of meaurement (MEINS) as "GRM".
Any idea why IDOC is picking ISO unit of measurement instead of material master base unit of measurement.
Any idea how to send base unit of measurememt as "G" instead of "GRM" in DOC segment.
Thanks
Nilesh

There are ISO codes for country keys, currency keys, units of measure and shipping instructions. According to SAP design guidelines, you should use ISO codes for an IDoc if they are available. When you set up the IDoc, the SAP codes have to be replaced by ISO codes.
http://help.sap.com/printdocu/core/Print46c/en/data/pdf/BCMIDALEPRO/BCMIDALEPRO.pdf

Ok i work at a military base and there were iPod touch's given out to some units and I have found one and would like to return it but don't know the owner so is there a way to track a name with the serial number?

Ok i work at a military base and there were iPod touch's given out to some units and I have found one and would like to return it but don't know the owner so is there a way to track a name with the serial number? Or how can I find out who owns it?

No. Turn it into the military police.

How can I adjust base and trebble on my 2007, MacBook Pro?

Is there any way to adjust base and trebble for external speakers hooked to my 2007, Macbookpro?

http://itunes.apple.com/us/app/boom/id415312377?mt=12&ign-mpt=uo%3D4

Please adjust base unit and coversion factor

Similar Messages

Maybe you are looking for