Please Help: Activity Units allocated in Full during Partial Confirmation
Dear All
I am facing a problem and need your help. When going for partial confirmation of a process order the system is allocating the full Costing Activity units. For example the process order is of 1000 units production and for 1000 unit production we have defined following controlling activities with certain rations
Setup
Machine
Labor
Factory Overhead
The unit of these activities are totally allocated even if i am going for a partial confirmation or i finally confirmed the process order even for 800 units. The unit and cost of these activities is charged on the basis of 1000 initially planned units.
Please help me urgently as we are having severe problems in Costing of process orders
Regards
Bilal Athar
Dear Siva
I have checked n OPK4 last tab page (Services --> Tick on Propose)
Its already ticked
And we are processing the confirmation through COR6N and here system is not displaying the activities automatically
Tell me what to do
Regards
Bilal Athar
Similar Messages
-
Please help, cannot compare images in full screen mode
I am not able to compare 2 images in full screen mode. I am using a MBP and a ACD 23". The main image will remain in the ACD while the image being compare is being shown in the MBP.
I am able to compare images in the viewer mode.
My main display is the ACD 23 which I selected using the display preferences under 'Arrangement' with the menu bar located on the ACD. In Aperture, Secondary Viewer is set to Blank.
I had also tried different combinations of Main Viewer and Secondary Viewer settings but was not successful.
Am I missing something? Anyone have the solution?Thanks in advance for any help.
norhengAnyone have any suggestions to using Aperture to edit images using a MBP and ACD so that it best utilize Aperture full screen mode in comparing and narrowing down to the pick.
I am now trying to use the MBP as the main display and ACD as the secondary. This way I am able to compare images with the MBP in the Browser mode and the ACD display the compare images full screen. It work with the secondary display - ACD set to mirror, span and alternate mode.
It would be best if only one screen is use and hence save energy consumption (reducing global warming and bill, if it help).
Thanks in advance for any suggestions or and solutions.
norheng -
Please help, i cannot purchase the full feat. It only tell that connot be completed.
GUys help me, i already downloaded the app but i can't purchase the full feature of the garageband. It only tell that purchase cannot be completed.
but for some reason, after I did that in-app purchase, that section has disappeared.
After the in-app purchase you have many more patches in your library. This way, the "Legacy" may have been scrolled out of view. Scroll the library pane upwards to reveal the patches at the bottom of the pane.
To scroll the pane, drag it upwards or use the scroll bars.
Only, GarageBand does not show any scrollbars, if they are not enabled in the System Preferences > General. Either enable the scroll bars there or simply try to drag the Library panel upward, even without the scrollbars showing. Or enable the scrollbars like shown below and scroll all the way up and to the left.
Instead of scrolling, you could also simply type "Legacy" into the search field on top of the library inspector pane (highlihted in Blue n the screenshot above). -
Please help activating EDU version of Master collection purchased from reseller
Last week I purchased the Adobe CS5 Master collection (Teacher and student edition) from a reseller and received the software package last Thursday (16th Feb).
On that same day, I followed the instructions and visited www.adobe.com/go/eduverify to register the product and receive my registration code.
I entered the customer support portal, logging in with my Adobe ID
I completed the online student edition order fulfilment form, in which I provided the Coupon code which was printed in the upper left corner of the Student Edition order fulfillment process instructions (inside my Adobe Student Edition box)
I attached a digital copy of my proof of eligibility (enrollment details from my college)
I have waited more than 3 working days for my e-mail from Adobe instructing me how to retrieve my serial number.
It has NOT arrived in any of my email inboxes (I have checked my online spam folders)
I have contacted and asked support (on a chat form) to help. They did not help at all, just explained that i needed to do what I have described above. I told them I had done that. They proceeded to tell me again that I needed to do that. I told them I had already done that. ...and etc. ad nauseum ....until I closed the chat window rather than type abuse at their obtuseness.
I have now also sent an email with my enrollment proof attached to [email protected]
I need to get my software unlocked. Is there anything anyone can suggest that might speed this process along a little so I can collect my registration code and get started using the software? someone special I need to contact? something special i need to do?
thanks in advance for any advice or help.
A very frustrated, hopefully soon to be, user.
Davidthanks acrwil16,
I should have explained that I am in Australia, so a telephone call is a little more complicated than if I lived in USA.
Apart from the call costs, I need to know the time zone I am calling to so I can pick an appropriate time to call, and I think they have a few over there, as we do here.
david -
Please help with better sql plan - full test case
Hello,
here is my test case:
SQL> create table ib_auth_devices(dv_id number(12) primary key , dv_cl_id number(12));
Table created.
SQL> create table ib_clients (cl_id number(12) primary key);
Table created.
SQL> alter table ib_auth_devices add constraint fk1 foreign key(dv_cl_id) references ib_clients(cl_id);
Table altered.
SQL> create table ib_tokens (to_dv_id number(12) primary key);
Table created.
SQL> alter table ib_tokens add constraint to_dv_id foreign key(to_dv_id) references ib_auth_devices(dv_id);
Table altered.
SQL> create table ib_auth_cards(au_dv_id number(12) primary key);
Table created.
SQL> alter table ib_auth_cards add constraint au_dv_id foreign key(au_dv_id) references ib_auth_devices(dv_id);
Table altered.
SQL> insert into ib_clients values(1);
1 row created.
SQL> insert into ib_clients values(2);
1 row created.
SQL> insert into ib_clients values(3);
1 row created.
SQL> insert into ib_clients values(4);
1 row created.
SQL> insert into ib_clients values(5);
1 row created.
SQL> commit;
Commit complete.
SQL> insert into ib_auth_devices values(1 , 1);
1 row created.
SQL> insert into ib_auth_devices values(2 , 2);
1 row created.
SQL> insert into ib_auth_devices values(3,3);
1 row created.
SQL> insert into ib_auth_devices values(4,4);
1 row created.
SQL> commit;
Commit complete.
SQL> insert into ib_tokens values(1);
1 row created.
SQL> insert into ib_tokens values(2);
1 row created.
SQL> insert into ib_tokens values(3);
1 row created.
SQL> insert into ib_auth_cards values(1);
1 row created.
SQL> insert into ib_auth_cards values(2);
1 row created.
SQL> commit;
Commit complete.
SQL> select cl_id from ib_clients;
CL_ID
1
2
3
4
5
SQL> select cl_id from ib_clients cli , ib_auth_devices ad
2 where
3 cli.cl_id = ad.dv_cl_id;
CL_ID
1
2
3
4
SQL> select * from ib_tokens;
TO_DV_ID
1
2
3
SQL> select * from ib_auth_cards;
AU_DV_ID
1
2
SQL> select * from ib_clients;
CL_ID
1
2
3
4
5
SQL> select * from ib_auth_devices;
DV_ID DV_CL_ID
1 1
2 2
3 3
4 4
SQL> exec dbms_stats.gather_table_stats(user , 'IB_AUTH_DEVICES' , cascade => true);
PL/SQL procedure successfully completed.
SQL> exec dbms_stats.gather_table_stats(user , 'IB_TOKENS' , cascade => true);
PL/SQL procedure successfully completed.
SQL> exec dbms_stats.gather_table_stats(user , 'IB_CLIENTS' , cascade => true);
PL/SQL procedure successfully completed.
SQL> exec dbms_stats.gather_table_stats(user , 'IB_AUTH_CARDS' , cascade => true);
PL/SQL procedure successfully completed.
SQL> l
1 select cli.cl_id from ib_clients cli , ib_auth_devices ad,
2 (select dv_cl_id as cl_id
3 from ib_auth_cards, ib_auth_devices
4 where
5 au_dv_id = dv_id
6 ) cards,
7 ( select dv_cl_id as cl_id
8 from ib_tokens, ib_auth_devices
9 where
10 to_dv_id = dv_id
11 ) tokens
12 where
13 cli.cl_id = ad.dv_cl_id
14 and cards.cl_id(+)= cli.cl_id
15 and cards.cl_id is null
16 and tokens.cl_id(+)= cli.cl_id
17* and tokens.cl_id is null
SQL> r
1 select cli.cl_id from ib_clients cli , ib_auth_devices ad,
2 (select dv_cl_id as cl_id
3 from ib_auth_cards, ib_auth_devices
4 where
5 au_dv_id = dv_id
6 ) cards,
7 ( select dv_cl_id as cl_id
8 from ib_tokens, ib_auth_devices
9 where
10 to_dv_id = dv_id
11 ) tokens
12 where
13 cli.cl_id = ad.dv_cl_id
14 and cards.cl_id(+)= cli.cl_id
15 and cards.cl_id is null
16 and tokens.cl_id(+)= cli.cl_id
17* and tokens.cl_id is null
Execution Plan
0 SELECT STATEMENT Optimizer=CHOOSE (Cost=5 Card=4 Bytes=128)
1 0 FILTER
2 1 HASH JOIN (OUTER)
3 2 FILTER
4 3 HASH JOIN (OUTER)
5 4 NESTED LOOPS (Cost=1 Card=4 Bytes=24)
6 5 TABLE ACCESS (FULL) OF 'IB_AUTH_DEVICES' (Cost=1
Card=4 Bytes=12)
7 5 INDEX (UNIQUE SCAN) OF 'SYS_C008299' (UNIQUE)
8 4 VIEW (Cost=1 Card=2 Bytes=26)
9 8 NESTED LOOPS (Cost=1 Card=2 Bytes=18)
10 9 TABLE ACCESS (FULL) OF 'IB_AUTH_DEVICES' (Cost
=1 Card=4 Bytes=24)
11 9 INDEX (UNIQUE SCAN) OF 'SYS_C008303' (UNIQUE)
12 2 VIEW (Cost=1 Card=3 Bytes=39)
13 12 NESTED LOOPS (Cost=1 Card=3 Bytes=27)
14 13 TABLE ACCESS (FULL) OF 'IB_AUTH_DEVICES' (Cost=1 C
ard=4 Bytes=24)
15 13 INDEX (UNIQUE SCAN) OF 'SYS_C008301' (UNIQUE)
Statistics
0 recursive calls
12 db block gets
9 consistent gets
0 physical reads
0 redo size
364 bytes sent via SQL*Net to client
431 bytes received via SQL*Net from client
2 SQL*Net roundtrips to/from client
8 sorts (memory)
0 sorts (disk)
1 rows processedAny ideas about rewriting this query to achive better performance ?
Oracle version 8.1.7
Best Regards.
GrzegorzThe answer to this question totally depends on the real volumes you have in your tables. Your test case is probably not showing us these volumes.
However, I see some needless table accesses, so it's probably safe to conclude that this rewrite will speed something up:
SQL> create table ib_auth_devices(dv_id number(12) primary key , dv_cl_id number(12));
Tabel is aangemaakt.
SQL> create table ib_clients (cl_id number(12) primary key);
Tabel is aangemaakt.
SQL> alter table ib_auth_devices add constraint fk1 foreign key(dv_cl_id) references ib_clients(cl_id);
Tabel is gewijzigd.
SQL> create table ib_tokens (to_dv_id number(12) primary key);
Tabel is aangemaakt.
SQL> alter table ib_tokens add constraint to_dv_id foreign key(to_dv_id) references ib_auth_devices(dv_id);
Tabel is gewijzigd.
SQL> create table ib_auth_cards(au_dv_id number(12) primary key);
Tabel is aangemaakt.
SQL> alter table ib_auth_cards add constraint au_dv_id foreign key(au_dv_id) references ib_auth_devices(dv_id);
Tabel is gewijzigd.
SQL> insert into ib_clients values(1);
1 rij is aangemaakt.
SQL> insert into ib_clients values(2);
1 rij is aangemaakt.
SQL> insert into ib_clients values(3);
1 rij is aangemaakt.
SQL> insert into ib_clients values(4);
1 rij is aangemaakt.
SQL> insert into ib_clients values(5);
1 rij is aangemaakt.
SQL> insert into ib_auth_devices values(1 , 1);
1 rij is aangemaakt.
SQL> insert into ib_auth_devices values(2 , 2);
1 rij is aangemaakt.
SQL> insert into ib_auth_devices values(3,3);
1 rij is aangemaakt.
SQL> insert into ib_auth_devices values(4,4);
1 rij is aangemaakt.
SQL> insert into ib_tokens values(1);
1 rij is aangemaakt.
SQL> insert into ib_tokens values(2);
1 rij is aangemaakt.
SQL> insert into ib_tokens values(3);
1 rij is aangemaakt.
SQL> insert into ib_auth_cards values(1);
1 rij is aangemaakt.
SQL> insert into ib_auth_cards values(2);
1 rij is aangemaakt.
SQL> exec dbms_stats.gather_table_stats(user , 'IB_AUTH_DEVICES' , cascade => true);
PL/SQL-procedure is geslaagd.
SQL> exec dbms_stats.gather_table_stats(user , 'IB_TOKENS' , cascade => true);
PL/SQL-procedure is geslaagd.
SQL> exec dbms_stats.gather_table_stats(user , 'IB_CLIENTS' , cascade => true);
PL/SQL-procedure is geslaagd.
SQL> exec dbms_stats.gather_table_stats(user , 'IB_AUTH_CARDS' , cascade => true);
PL/SQL-procedure is geslaagd.
SQL> set autotrace on explain
SQL> select cli.cl_id
2 from ib_clients cli
3 , ib_auth_devices ad
4 , ( select dv_cl_id as cl_id
5 from ib_auth_cards
6 , ib_auth_devices
7 where au_dv_id = dv_id
8 ) cards
9 , ( select dv_cl_id as cl_id
10 from ib_tokens
11 , ib_auth_devices
12 where to_dv_id = dv_id
13 ) tokens
14 where cli.cl_id = ad.dv_cl_id
15 and cards.cl_id(+)= cli.cl_id
16 and cards.cl_id is null
17 and tokens.cl_id(+)= cli.cl_id
18 and tokens.cl_id is null
19 /
CL_ID
4
1 rij is geselecteerd.
Uitvoeringspan
0 SELECT STATEMENT Optimizer=CHOOSE (Cost=10 Card=4 Bytes=128)
1 0 FILTER
2 1 HASH JOIN (OUTER)
3 2 FILTER
4 3 HASH JOIN (OUTER)
5 4 NESTED LOOPS (Cost=4 Card=4 Bytes=24)
6 5 TABLE ACCESS (FULL) OF 'IB_AUTH_DEVICES' (Cost=3 Card=4 Bytes=12)
7 5 INDEX (UNIQUE SCAN) OF 'SYS_C001354381' (UNIQUE) (Cost=1 Card=1 Bytes=3)
8 4 VIEW (Cost=3 Card=2 Bytes=26)
9 8 NESTED LOOPS (Cost=3 Card=2 Bytes=18)
10 9 INDEX (FULL SCAN) OF 'SYS_C001354385' (UNIQUE) (Cost=2 Card=2 Bytes=6)
11 9 TABLE ACCESS (BY INDEX ROWID) OF 'IB_AUTH_DEVICES' (Cost=2 Card=1 Bytes=6)
12 11 INDEX (UNIQUE SCAN) OF 'SYS_C001354380' (UNIQUE) (Cost=1 Card=1)
13 2 VIEW (Cost=3 Card=3 Bytes=39)
14 13 NESTED LOOPS (Cost=3 Card=3 Bytes=27)
15 14 INDEX (FULL SCAN) OF 'SYS_C001354383' (UNIQUE) (Cost=2 Card=3 Bytes=9)
16 14 TABLE ACCESS (BY INDEX ROWID) OF 'IB_AUTH_DEVICES' (Cost=2 Card=1 Bytes=6)
17 16 INDEX (UNIQUE SCAN) OF 'SYS_C001354380' (UNIQUE) (Cost=1 Card=1)
SQL> select cli.cl_id
2 from ib_clients cli
3 , ib_auth_devices ad
4 where cli.cl_id = ad.dv_cl_id
5 and not exists
6 ( select 'dummy'
7 from ib_auth_cards
8 where au_dv_id = ad.dv_id
9 )
10 and not exists
11 ( select 'dummy'
12 from ib_tokens
13 where to_dv_id = ad.dv_id
14 )
15 /
CL_ID
4
1 rij is geselecteerd.
Uitvoeringspan
0 SELECT STATEMENT Optimizer=CHOOSE (Cost=8 Card=1 Bytes=9)
1 0 FILTER
2 1 NESTED LOOPS (Cost=4 Card=1 Bytes=9)
3 2 TABLE ACCESS (FULL) OF 'IB_AUTH_DEVICES' (Cost=3 Card=1 Bytes=6)
4 2 INDEX (UNIQUE SCAN) OF 'SYS_C001354381' (UNIQUE) (Cost=1 Card=1 Bytes=3)
5 1 INDEX (UNIQUE SCAN) OF 'SYS_C001354385' (UNIQUE) (Cost=1 Card=1 Bytes=3)
6 1 INDEX (UNIQUE SCAN) OF 'SYS_C001354383' (UNIQUE) (Cost=1 Card=1 Bytes=3)Regards,
Rob. -
Please Help. OS Installation Freezing, Shutdown during memtest
Hi everyone. I've decided to build my first computer. I spent quite alot of time trying to install windows 8.1 because it kept freezing on the 'getting files ready for installation' step.
After trying 8 or so times unsuccessfully, I took out my second memory stick (located in slot 4) and ran the install again, It worked fine on the first try.
(note: before successful installation one time, I tried to turn the computer on, pressed the power button, but nothing happened. I don't know if this was the cause of it, but i unplugged all peripherals and the computer powered up fine).
I then installed the latest drivers for my GPU, etc with no problems. (with both memory sticks in)
Decided to run memtest86 (with ram1 in slot 2, and ram 2 in slot 4 as instructed by my mobos manual) and after about 2 hours (0 errors showing), my computer just shut itself off, then after about a minute or so, it restarted and the test continued (automatically). About 3 minutes after that it shut off again (this time it didn't restart). When I tried to turn it on again, it didn't do so. After about 5 minutes I was able to turn it on again
I'm not too knowledgeable on these things and am hoping someone could help me out with recommendations. Has anyone ever experienced this?
I just ran Ram #1 in dimm slot 2 overnight using memtest86, and it seems to check out. Swapped Ram #2 with Ram #1 in dimm slot 2 and will run for the next 5(6?) hours.
After that, upon someones recommendation I will run ram#1 (since its proven to be good), in Dimm slot 4 and see if the issue is with the dimm slot.
After that, I am completely clueless what to check next if that is fine.
My build:
i7 4770k
MSI z87 g45 motherboard
MSI Gtx 770 gaming edition
Corsair RM650
G.Skill Ripjaws X – 2x4
Corsair h80i
CM Storm Scout 2 Case
LG DVD/RW
Samsung 840 evo 120gb
WD Caviar Blue 1tb
Thanks so much!Quote from: badboy2k on 15-February-14, 01:42:18
why I suggested setting it manually is G-Skill on the ripjaws have skewed SPD and XMP profiles on them to increase the performance on ASUS boards only and cause problems elsewhere as they made a deal years ago to do that for there boards BIOS implementations to get higher performance numbers and cause problems else where!
so Manually setting them would get around them Inbuilt SPD sets by setting more typical Values for RAM in general if that makes sense to you!
Ahh, so that's why... interesting. That's kind of a bugger, especially for new builders like me.
Anyways, I will make sure to make these changes as soon as I can. Then run Intel burn test for a while as Xmad mentioned, and if that goes well, hopefully i can move on to GPU benchmarks and be happy! -
Please help! My itunes just stops during sync, but says "Sync In Progress"
Ok I've tried syncing my iphone to itunes and it just says Sync in Progress. It never stops. Now it makes it through the "Backing up iPhone" portion but as soon as it gets to syncing contacts, it just sits there saying its "Syncing contacts with "iphone"". Now Im not sure why its doing this, this just happened out of nowhere, so I've even restored the phone twice, once as a new phone and then again with the option it left from restoring it the first time. It syncs the music, apps, and videos when I uncheck everything in the Info tab, such as contacts, calendar, etc. So its something to do with everything in the Info tab. But how do i fix this problem?? =\
It sounds like when replacing the hard drive for whatever reason your contacts were not loaded on your new drive. Syncing the device does not put contacts on your drive.
If you still have the old drive, you could reinstall it and export the contacts from whatever contact management app you use, then remove the old drive and reinstall the new drive, importing the contacts back into your contact management app.
If you have your contacts backed up elsewhere, that would be the simplest solution. Simply restore them or import them back into your contact management app.
Personally, I would not trust the iTunes backup as a solution for keeping my contacts. I choose to use MobileMe and Google contacts to provide backups and sync points for my contacts. -
Please help me exit "full screen mode." I am unable to see the Safari menu bar.
I have never used this tool. Please help me to "exit the full screen mode." I am unable to see the toolbar in Safari.
kennedy0520 wrote:
THANK YOU FOR RESPONDING. Is there a way to adjust settings in Safari, like my homepage? So far I am not pleased with the IPad. Wish I had looked at other tablets before buying. the main thing I don't like is Safari. I welcome any positive comments. Thanks.
Safari doesn't include a Home page, but does allow for a multitude of book marks. In addition, there numerous other browsers available in the apps store. Some of them will allow for setting Home page if it is that important to you (personally, I don't miss it).
The bookmarks bar can be be hidden from the setting app. There is no real tool bar in Safari.
You might want to take a look through the User Guide and learn a little more about how the iPad works, if you haven't already.
http://manuals.info.apple.com/en_US/ipad_user_guide.pdf -
XML Data Set with Spry Slides - Please Help
Hi, I'm trying to combine XML Data Set with sliding tabs.
I've created two keys responsible for sliding the tabs:
<a id="previous" href="#"
onclick="sp1.showPreviousPanel();">Previous</a>
<a id="next" href="#"
onclick="sp1.showNextPanel();">Next</a>
Then XML Data Set is used to populate the tabs, but only a
single tab remains visible, and a "Next/Previous" buttons are used
to move to the next tab. And this is where the problem arises.
The problem is that, every time I refreash the gallery or
load it for the first time, I have to press TWICE the "Next" button
to move to the next image. After that, its all fine, and slides
well. It's only the FIRST time when loaded.
Please help.
Here's the full code:
<div id="images_gal" >
///////////////////////////////////////// The menu - the
culprit///////////////////////////////////////////
<div id="menu_next">
<a id="previous" href="#"
onclick="sp1.showPreviousPanel();">Previous</a>
<a id="next" href="#"
onclick="sp1.showNextPanel();">Next</a>
</div>
//////////////////////////////////////// The Sliding Panels
Gallery ////////////////////////////////////////////////////
<div id="example2" class="SlidingPanels" tabindex="0" >
<div class="SlidingPanelsContentGroup"
spry:region="dsSpecials">
<div spry:repeat="dsSpecials" id="{first}"
class="SlidingPanelsContent{second}"><div class="top_gal"
></div><div class="main_gal"><img
src="images/Galery/{third}" alt="Digital_Signage" width="600"
height="304" />
<p class="screen_gal"><a href="#"
onclick="MM_openBrWindow('film1.html','Coloris','width=340,height=260,
top=250, left=250')">CLICK TO VIEW</a></p>
</div><div
class="bottom_gal"></div></div>
</div>
</div>Anyone has any idea why I need a DOUBLE Click to start moving
the sliding panels?
I've just completed two tutorials by Don Booth.
1/Building a Spry Sliding Panels widget
2/Building a photo album with the Spry framework
But what I try to COMBINE them - display the photos in
sliding panels, I also need to DOUBLE click the "next" buton before
it starts scrolling.
Why is that Double Click needed? Help Please.
Here's my code for the combined version:
<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0
Transitional//EN" "
http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">
<html xmlns="
http://www.w3.org/1999/xhtml">
<head>
<meta http-equiv="Content-Type" content="text/html;
charset=utf-8" />
<title>Untitled Document</title>
<style type="text/css">
a {
position:relative;
left:23px;
top:127px;
z-index:10000;
color: #FF0000;
</style>
<script type="text/javascript"
src="photo_album_samples/includes/xpath.js"></script>
<script type="text/javascript"
src="photo_album_samples/includes/sprydata.js"></script>
<script type="text/javascript"
src="Spry/SprySlidingPanels.js"></script>
<link type="text/css" rel="stylesheet"
href="Spry/SprySlidingPanels.css">
</head>
<body>
<div >
<a href="#" onclick="sp1.showPreviousPanel();">Previous
Panel</a>
<a href="#" onclick="sp1.showNextPanel();" >Next
Panel</a>
</div>
<div id="panelwidget" class="SlidingPanels" >
<div class="SlidingPanelsContentGroup"
spry:region="dsGallery" >
<div spry:repeat="dsGallery" class="SlidingPanelsContent"
id="p1"><img
src="photo_album_samples/thumbnails/{@thumbpath}"/></div>
</div>
</div>
<script type="text/javascript">
var dsGallery = new
Spry.Data.XMLDataSet("photo_album_samples/photos.xml",
"gallery/photos/photo");
</script>
<script type="text/javascript">
var sp1 = new Spry.Widget.SlidingPanels("panelwidget");
</script>
</body>
</html> -
I have mac book pro, 15inch server color, 2008 modal, few days before I was watching movie at the same time I was chating on face book, suddenly my mac stuck so I just tried to force shutdown, by pressing shadown key for 7sec, and after I try to turn on, but nothing comes on display it's black ad if it's off, but laptop fan is on the led is on its heat is as if it's working, after I tried to reset then it's started making beep noses for ten times and again same thing nothing comes on display black, but sounds like fan is on and led blink, please help me
Hi Aparana.rahul,
The beeps during the startup of your MacBook Pro indicate that it may need to be serviced. See this article for further information -
OS X Mavericks: If you hear beeps when your computer starts up
http://support.apple.com/kb/PH14206
Note that while the article title says it is for computers running Mac OS X 10.9 Mavericks, the same information applies to other versions.
Thanks for using Apple Support Communities.
Best,
Brett L -
Syncing problem with 3Gs, please help!
I just bought the new iphone. I then sync'd my old phone one last time with iTunes 8, then plugged in the new phone assuming that the backed-up sync would carry to my new phone. It seems the new phone only sees a sync from a few months ago, so not all of my settings and texts and emails have carried over. Please help!
Just did a full restore on my 3GS and when it restored it properly restored the latest/desired backup set of everything.
-
Please help urgently - can't download App World
Dear all,
I posted yesterday about how I've lost access to WhatsApp on my Blackberry Z10. I'm a lecturer and use WhatsApp to communicate with my students so it is urgent that I get back on ASAP. I could not get the application to update or download so I deleted it but that has not helped. The root problem seems to be that App World is gone from my BB, and I can't get it back either.
I have tried several methods of downloading App World and none of them work.
1. If I enter the URL appworld.blackberry.com in the browser on my BB, I get the error "Unable to open appworld://"
2. If I visit www.blackberry.com/appworld/download as instructed on the BB website, it states:
"Simply visit www.blackberry.com/appworld/download from your smartphone to download. Or, enter an email address that’s integrated with your BlackBerry smartphone below and click submit to have a download link sent to you."
When I enter the URL www.blackberry.com/appworld/download in my BB browser it simply refreshes the same page with the same instructions.
3. If I enter the email address integrated with my BB, it sends me an email with the following URL in it:
http://mobileapps.blackberry.com/devicesoftware/entry.do?code=appworld
Currently, entering this URL on my PC or in my BB yields an "HTTP Status 500" exception report. Previously (last night), the same URL was giving the following instruction: "Downloads via a USB connection are not enabled for this product. Please visit our mobile download site using the browser on your Blackberry." But I was using the browser on my BlackBerry and not a USB connection.
4. Searching around the web desperately for a workaround, I found a suggestion to download BlackBerry App World directly from the web at this link. However, when I downloaded this file to my BB and tried to open it, it just said "Unable to open file".
I'm now out of ideas! Please help.Hi @tom-81030
Thats strange! To confirm, what happens if tyou open BlackBerry World and search for WhatsApp?
This should allow you to see WhatsApp and provide a Install option (link).
If searching for the app doesnt produce any results, try scanning the following QR Code using BlackBerry World on your device. To do this, open BlackBerry World, swipe down from the top of your screen and tap Scan Barcode.
Let me know if this helps!
Did someone help you? Click Like! Did a post solve your issue? Click Accept as Solution!
Follow me on Twitter or Google+ and subscribe to the Inside BlackBerry Help Blog -
I have not been able to use the presenter installation. The installation process finishes well by says the download installation was a sucess, however, the icon to begin using the app is not shown anywhere. Please help!!!
Hi There,
Can you confirm if you were able to download Presenter 10 successfully, Can you please paste the screen shot of the downloaded file for Presenter 10? Can you please check in control panel >Program and features and check if you are able to see Adobe Presenter 10 as a installed program?
Regards,
Mayank -
Goods movement during operation confirmation
Hi Gurus
Currently My system is backflushing all the components when i partially confirm the operation through Co11n T-code, which i dont want. I want the backflushing should happen only after the final confirmation of the operation.
Is there any configuration change required to stop the backflushing only during partial confirmation.
Thanks in advance,
Quantum.Hi
In SAP U can do backflush in 3 ways
Indicator: Backflush
Determines whether the backflush indicator is set in the production order. Here, a 3-level hierarchical logic is applied:
1. In the routing, the backflush indicator is set in the component assignment.
2. In the material master record, the backflush indicator has the characteristic "Always backflush".
3. In the material master record, the backflush indicator has the characteristic "Work center decides",
the indicator being set in the work center.
If at all u dont want to Backflush at the time of Confirmation in CO11N, partial confirmation , dont set any backflush indicator in any level, u can go for Manual Goobs issue Using MB1A, So that u can confirm Goods issue , and final component u can confim By setting Auto goods recipt with the help of Control Key for the last operation in routing.
i Hope this will help.
madhu -
My icloud activation lock is on my iphone, which requires an activation login to access the homescreen, but when i log in with the apple ID on the phone, it says the apple ID is not meant to unclock this iphone 5 ios 8.0.2. please help me solve this.
Yes the phone belongs to me. It was purchased from United Kingdom Vodafone to West Africa, i had to factory unlock to use any sim in it. so it belongs to me. I did the activation myself, now after updating my iphone to the latest update, it required a user id and password to activate the phone, but anytime i enter the details, it tells me the user Id is not correct but the password is correct..
Maybe you are looking for
-
I am getting followong error XML Parsing Error: undefined entity Location: chrome://weave/content/options.xul Line Number 6, Column 3: <setting id="weave-account" type="string" title="&account.label;" /> --^
-
Clementine can't play files with special characters
I saw Clementine can't play some mp3 files - it would just say "error loading file". So I opened an mp3 from the terminal and found out that the problem was the characters in the file name. For example, it wouldn't play "Schiller - Tired (mit Jaël).m
-
Create a new class which extends DataGrid
Can someone give me a simple example on how to create a new class that extends DataGrid. Still having a little trouble understanding classes. Thanks for any help. Jeremy
-
I need to know how to stop a notification that keeps coming up when playing a spades game, that keeps telling me to go to the game center. I even shut off the notifications in the settings, this is an anoying problem
-
How to combine munltiple album songs under one ablum?
I have looked all around the iTunes Help section and just can't seem where to find out how to combine album songs under one album in the cover flow view. I know it's confusing so here is a picture of what I mean. The circled part is what I want to be