PLEASE HELP flashing light and playbook doesn't switch on!!

Hello,
I have my tablet won't switch on and when I try to turn on, the red light and green light flashing 5 times. And then nothing. Unable to turn on.
I tried a reboot by pressing power + volume - and nothing!
I tried to update with BlackBerry Desktop Manager (latest version) and when the update reaches the end error message comes to me and it there was a problem: "A connection to the tablet Could not be ESTABLISHED. Please connect your tablet and try again. "
I also tried to charge it with a 2000mA charger for several hours and still nothing.
I no longer guarantee
Please help me, I do not know what to do.
thank you
sorry for my english

Same thing happened to me yesterday. After the error message, I plugged in the charger. It took quite a while but the tablet started charging. It reinstalled the update when it reached the 20% level. Another update error came up to change my setting. I checked my setting but didn't change anything and just reinstall update again which this time was a success. Hope this would help.

Similar Messages

Can't find a playlist I created on my playlist or computer? I didn't delete it. I don't want to create it again because it took a long time. please help me find and recover.

Can't find a playlist I created on my playlist or computer? I didn't delete it. I don't want to create it again because it took a long time. please help me find and recover.

Playlists only exist as part of the larger iTunes library listing so if you are not seeing it there it doesn't exist anywhere else. I know with my older version of iTunes it is very easy to accidentally delete a playlist. With newer versions it may be possible to recover it with the undo feature in the menu but this likely will only work immediately after the deletion.

HT4623 please help - installed IOS7 and now I am having problems playing Words Free on my Iphone. It gives me a pop up telling me to connect to ITunes but will not connect. Cannot get out and have to continually shut down my phone and start over.

please help - installed IOS7 and now I am having problems playing Words Free on my Iphone. It gives me a pop up telling me to connect to ITunes but will not connect. Cannot get out and have to continually shut down my phone and start over.

Hi, jeantwin.
Thank you for visiting Apple Support Communities.
The steps in the article below may help you resolve the issue with push notifications.
iPad and iPod touch: Unable to use YouTube or Push notifications
http://support.apple.com/kb/ts3305
If the issue persists, try signing out of your Apple ID and then sign back in.
iOS: Changing the signed-in iTunes Store Apple ID account
http://support.apple.com/kb/HT1311
Cheers,
Jason H.

Can I replace the G5 CP units in my pre intel power mac? I get the 3 flash light and am heating them with a hair dryer. It works but needs fixing and I can't afford a new mac

Can I replace the G5 CP units in my pre intel power mac? I get the 3 flash light and am heating them with a hair dryer. It works but needs fixing and I can't afford a new mac

OK, it looks like all but the first G5 1.6 Ghz, & the last 3 G5 Dual Cores will take PC3200 RAM...
Power Macintosh G5 1.8 (PCI-X) PowerMac7,2 1 Power Macintosh G5 2.0 DP (PCI-X) PowerMac7,2 1 Power Macintosh G5 1.8 DP (PCI-X) PowerMac7,2 1 Power Macintosh G5 1.8 DP (PCI) PowerMac7,3 1 Power Macintosh G5 2.0 DP (PCI-X 2) PowerMac7,3 1 Power Macintosh G5 2.5 DP (PCI-X) PowerMac7,3 1 Power Macintosh G5 1.8 (PCI) PowerMac9,1 1 Power Macintosh G5 2.0 DP (PCI) PowerMac7,3 1 Power Macintosh G5 2.3 DP (PCI-X) PowerMac7,3 1 Power Macintosh G5 2.7 DP (PCI-X) PowerMac7,3

PLEASE Help! - Bridge and Premiere CC- "the operation could not be completed" and export error - MAC

Dear Adobe Community,
I got my first imac a few days ago, and i decided to install Adobe CC.
When i want to run Adobe Bridge, says "the operation could not be completed", the same happens with Adobe After Effects.
And I also have a problem with Premiere, when i want to export a project says that premiere must close.
This is the try version, is this a problem of Adobe or Apple? i'm very worried
Help!
Thank you!
Ivana

Muchas gracias!!! Ha funcionado!
El 11/02/2014, a las 00:02, Federico Platon <[email protected]> escribió:
Re: PLEASE Help! - Bridge and Premiere CC- "the operation could not be completed" and export error - MAC
created by Federico Platon in Foros de usuario a usuario - View the full discussion
Confirma que se trata de una cuestión de permisos.
Por cierto te aconsejos actualices la 9.1 a 9.2, posiblemente se habría arreglado así también.
Bueno los pasos son:
2. Select Go from the Finder Menu.
3. Select Computer.
4. Select Macintosh HD.
5. Select Users.
6. Select your user profile.
7. Right click on user profile. Select Get Info.
8. Go to bottom and unlock with admin password to make changes.
9. Make sure your user profile has Read and Write privileges by selecting from dropdown menu.
10. Go down to wheel at very bottom and select Apply to enclosed items. This should allow Adobe Bridge to run properly.
Creo que no se necesita traducción.
Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/6107188#6107188
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/6107188#6107188
To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/6107188#6107188. In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Foros de usuario a usuario at Adobe Community
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/thread/416458?tstart=0.

IF YOU HELP MY NANO upgraded when you install PERFECT BUT DOES NOT APPEAR ON THE SCREEN NOTHING BUT as if you were OFF if turned PLEASE HELP OR MORE AND HAS THE NEW UPDATE

IF YOU HELP MY NANO upgraded when you install PERFECT BUT DOES NOT APPEAR ON THE SCREEN NOTHING BUT as if you were OFF if turned PLEASE HELP OR MORE AND HAS THE NEW UPDATE

iPod not recognized in 'My Computer' and in iTunes for Windows

I want to be a good SAP user but please help me how and can i do the right step about SAP

i want to be a good SAP user but please help me how and can i do the right step about SAP

Hi,
you can start learning SAP from an end-user/key-user perspective with the online learning portal of SAP Learning Hub, business user edition.
Further information can be found here:
SAP Learning Hub
Regards,
Arnold

Please help me download and install Flash Player!

One day, I had no problems viewing Flash on my computer. Then
one day last week, it told me I needed to download Flash Player 8
to view The Vine on E!Online. I haven't been able to download Flash
Player 8 or 9. Or anything from this site, for that matter.
I went here (
http://www.adobe.com/shockwave/download/download.cgi?P1_Prod_Version=ShockwaveFlash&promoi d=BIOW),
clicked download. Clicked the yellow strip that appeared to install
the Active X control or whatever it's called. A pop-up asked if I
wanted to install or do not install. I clicked install, then
nothing happens. No download box shows up or anything.
I've un-installed my flash player (if i even had one) and
have tried so many times to download a new flash player.
PLEASE HELP!

ive uploaded the exe file to my server, so
go
here and save it to your comp, unzip the file, and run the
program.

Please Help- IPod Classic and Mac/Itunes

Hi all,
I'm new here because I have a bit of a problem. Please forgive me for my lack of general computer/Ipod knowledge...
I purchased my MacBook about 4 1/2 years ago. I'm not sure exactly what model I have, but the age should help you determine that.
I also purchased my Ipod about 5 years ago. I think it's the first "video" Ipod that came out. It's 40 Gig, white, and pretty basic.
I've taken exquisite care of my Ipod because I'm just interested in putting my new CD's on it, and taking it with me in the car so I don't have to lug around 40 CD's all the time.
Anyway, for the last 2 years or so, my process of putting new music on my IPod was as follows:
1. Open Itunes
2. Import CD
3. Hook Ipod up to the USB port (my Ipod is not synched)
4. Click and highlight the new CD and drag it to my Ipod
5. After updating, disconnect my Ipod
6. Delete CD off of Itunes libary
This has gone off without a hitch for quite some time.
The other day, I went through this exact process, as I've purchased a new CD, but I had an issue.
After I plugged my Ipod in, Itunes recognized it, as usual. But, on the Ipod screen, it continued to flash "do not disconnect." After a half hour of waiting, it didn't go away. I tried to drag the new songs to my Ipod like usual, and then disconnect, but to no avail.
In the past, when I hooked up my Ipod, after about 20 seconds, the "Do Not Disconnect" screen would disappear, and take me to my main menu (on the Ipod).
Now, that screen doesn't turn off, and I can't get new songs onto the device.
Please help...I'm not very good with any of this, and would very much like to hear my new music.
Thanks for your help!
Jeff

hold the menu and middle buttons down together until the screen on the ipod goes blank. that restarts it then try your normal process again

Please Help - Time Capsule and External hard drive Issues

Recently, I switched from Comcast to AT&T uverse as my internet provider and I started experiencing problems.
(1) I have a 4th generation Apple Time Capsule which I am using as my router.
(2) Connected to the Apple Time Capsule - USB - is an external hard drive (not for backup with Time Machine.)
(3) I have a 2011 Macbook pro which I use to access my file on my time capsule and external hard drive.
(4) I had been using my AT&T portable Hotspot from my cell phone to get internet access on my MacBook pro from remote locations to gain access to my external hard drive which is attached to the time capsule.
(5) On August 2, 2014, I switched from Comcast to AT&T and had the AT&T turn off the router function. (I have been using the router from my apple time capsule)
(6) Under Network I switched to bridge mode.
(7) And since August 2, 2014 my time capsule has not been backup.
THE PROBLEM - I need to be able to use the hotspot function from my cell phone to gain access on the external hard drive using my MacBook Pro which I was able to do before. Now it is showing time capsule under finder but unable to connect.
Do I need to reset my Time Capsule since I have a new service provider. Everything else works fine - meaning able to get internet signal but unable to access my external hard drive and backup my time capsule. Please HELP.

(5) On August 2, 2014, I switched from Comcast to AT&T and had the AT&T turn off the router function. (I have been using the router from my apple time capsule)
(6) Under Network I switched to bridge mode.
(7) And since August 2, 2014 my time capsule has not been backup.
If you got ATT to turn off router function in their modem..
Then 6. is wrong.. You cannot have the Network switched to bridge mode..
You must have it set to dhcp and nat.
That is also why you cannot backup.. the TC is off the network.
Please change back to router mode in the TC.
Ensure the internet tab shows dhcp and you create a wireless network.
Then power down the TC... power down the ATT modem.. wait about 20min (you can try 5min.. but it might not be long enough).
Power up the ATT modem.. wait 2min for things to flash lights in de right blinkin order.. then start the TC.
Open the airport utility and make sure your TC captured the public IP and is now working as the router.
That should fix that end of it.. the hotspot end??
Tell us what happens.

Updating flash player and still doesn't work.

Recently, my games on Facebook and Youtube stopped working and prompted me to upgrade my flash player.
It included the link to Adobe, as do all the sites that require it.
So, I did. It says install successful, but it doesn't work. When I check to see if any version is installed, I see the red x. Please help.
I'm using Windows XP Version 2002 Service Pack 3
I.E. 8 32 bit.
P.S. I can use Firefox and Chrome, but I don't like the quality of how Flash Player runs on them.

Hi, I see from the other thread you commented on that the Kill-bit was your problem. Glad that worked for you:-)
Thread reference: http://forums.adobe.com/thread/829621?tstart=0
If you would, please mark this thread as answered even tho your solution wasn't from here.
Thanks,
eidnolb

Please Help, Flash Player for Mac

I am running Mac OS X 10.7.5. Last night Facebook told me I MUST update to the newest version of Flash Player in order to upload multiple pics. I kept getting plug-in failure messages and then the message saying I need to update my version of Flash.
Problem is I have updated my version of Flash and the plug in still doesn't work. Please help, my business relies on my being able to upload multiple photos daily to social media. What is going on? I have read the forums, the work arounds posted on 4/16. Uninstalled, re-installed, etc. I am still getting flash plug in failures even on Adobe's site. What do I do?

No.
I am in the same boat. I cannot watch flash videos on the BBC website or on BBC iPlayer, although all other flash videos (YouTube for example) are fine.
For reasons that passeth all understanding, they work with the PPC version of Firefox, called TenFourFoxG5.app, once you have anabled plug-ins, as it does not natively support Flash.
You can download TenFourFoxG5 from here:
http://www.floodgap.com/software/tenfourfox/
Now for the intersting bit: TenFourFox, like Firefox, does not support most plug-ins. Unless you are prone to headaches (in which case don't) you can read about that here:
http://code.google.com/p/tenfourfox/wiki/PluginsNoLongerSupported
But there is a workaround!
Open TenFourFox and type in the address bar: about:config (no spaces) and click return. This gives you a warning that it might harm the application. Ignore that and click on 'I'll be careful, I promise' and you get the config file that you can edit - with great care.
Look/search (scroll down) for: tenfourfox.plugins.enabled
Set it to true. (Double click it to toggle it)
Now close TenFourFox, open it again, and Flash will now work, as it now uses the plug-ins that Safari has stored.
I am using Flash 10.1.102.64 in TenFourFox and it works just fine.

Please Help! Drag and drop does not work in Adobe AIR 3.1 (FlashBuilder 4.6)

I am working on a PC is made of air and flashbuilder 4.6.
Drag and drop application does not work in Flash Builder 4.6.
However, the same source will work with Flash Builder 4.5.
Please help me.
<?xml version="1.0" encoding="utf-8"?>
<s:WindowedApplication xmlns:fx="http://ns.adobe.com/mxml/2009"
                              xmlns:s="library://ns.adobe.com/flex/spark"
                              xmlns:mx="library://ns.adobe.com/flex/mx"
                              backgroundColor="#323232" width="100%" height="100%"
                              initialize="init(event)"
                              nativeDragEnter="onDragEnter(event)"
                              nativeDragDrop="onDragDrop(event)">
          <fx:Script>
          <![CDATA[
                    import mx.events.FlexEvent;
                    protected function init(event:FlexEvent):void
                              addEventListener(NativeDragEvent.NATIVE_DRAG_ENTER, onDragEnter);
                              addEventListener(NativeDragEvent.NATIVE_DRAG_DROP, onDragDrop);
                    private function onDragEnter(event:NativeDragEvent):void
                              if (event.clipboard.hasFormat(ClipboardFormats.FILE_LIST_FORMAT))
                                        NativeDragManager.acceptDragDrop(this);
                    private function onDragDrop(event:NativeDragEvent):void
                              var arr:Array;
                              arr = Array(event.clipboard.getData(ClipboardFormats.FILE_LIST_FORMAT));
                              startImage.source = (arr[0] as File).url;
            ]]>
          </fx:Script>
          <s:layout>
                    <s:VerticalLayout/>
          </s:layout>
          <s:BorderContainer id="bc" borderStyle="solid" width="200" height="80%"/>
          <s:Image id="startImage" width="100%" height="100%"
                                         horizontalAlign="center" verticalAlign="middle"/>
</s:WindowedApplication>

Thank you answers, but it was not the answer I wanted.
[Problem]
* Flash Builder 4.5.1(updater) or Flash Builder 4.6
- If you have installed on pc, does not work adobe air drag and drop
[Solution]
1. Reinstalling the Windows 7 (32bit).
2. Install Flash Builder 4.5.
3. Flash Builder 4.5.1 updater and Flash Builder 4.6 does not install.
   (Instead of using Flex SDK 4.6 is set up)
In addition, Windows7 64bit environment does not work drag and drop.
Is there another solution?

Please help, iPod Nano and iTunes issues

1. I can't update my iPod Product Red. I've downloaded the update, and when I click "update" in iTunes, it just sits there for hours saying its updating
2. The first time I start windows, connect my iPod Nano and then start iTunes (or even the other way around, start itunes then connect ipod), my nano doesn't show up in itunes. I need to restart the service after plugging in the nano every single time!
3. I cant restore my iPod Nano either, the same problem with the updating my ipod, the progress screen just goes back and forth for hours without doing anything, infact my nano just seems like it looses synch during both an update and a restore, because the do not disconnect message on the screen goes away once either update or restore process is started.
Please help! This is my first ipod purchase and so far it is really disappointing me and frustrating, thanks
-Alex

1. I can't update my iPod Product Red. I've downloaded the update, and when I click "update" in iTunes, it just sits there for hours saying its updating
2. The first time I start windows, connect my iPod Nano and then start iTunes (or even the other way around, start itunes then connect ipod), my nano doesn't show up in itunes. I need to restart the service after plugging in the nano every single time!
3. I cant restore my iPod Nano either, the same problem with the updating my ipod, the progress screen just goes back and forth for hours without doing anything, infact my nano just seems like it looses synch during both an update and a restore, because the do not disconnect message on the screen goes away once either update or restore process is started.
with that particular set of symptoms, first check on the possibility described in the following document:
iTunes for Windows: iTunes 7 doesn't recognize iPod

Please help (flash intro cs4)!!!

sorry if I posted in the wrong section but I need help.
I have a flash intro and when ever I preview it,the intro background turns to black instead of staying the way it should be.Can somebody please help me out here,I need this flash intro for a website.Please explain this to me in simple terms because im pretty NEW to adobe.
Thanks
Kevin
Note I've tried everything to make the flash background stay the way it was but nothing I do works.

the color is black
watch this intro
http://images.templatemonster.com/screenshots/21000/21016.html
i have this intro. I open it in flash and play it. As soon as the Offbeat idea text goes away the background fades to black instead of staying consistent.

PLEASE HELP flashing light and playbook doesn't switch on!!

Similar Messages

Maybe you are looking for