Please help FX5500 Voltage
Ok I have been searching the net for about a week and have found no conclusive answers. My question is..... What voltage does the FX5500 256Mb card run at? 1.5V or 0.8V? I desprately need to know this as soon as possible. Because I am buying it tommorow. I will be extremely thankfull....... I cant say how much I appreciate any help.
Mattwizz3 : )
Thank you so very very much! I wish this information was in the cards specs.
Thanks for the fast reply.
Mattwizz3
Similar Messages
-
IPhone 5 brightness permanently reduced (Please help, voltage issue??)
Hello,
I really need someone with high expertise to help me. Obviously i appreciate any help given but please dont say point less comment like reboot the phone or turn autobrightness off.
Here is the issue:
I have had several iPhones, right from the first to the 5. Lucky me. But i have always had the same issue. The screen brightness is significantly lower than any other iPhone that I compare it to.
Now i have the iPhone 5, if i compare it to anyone elses the brighness is much lower. Autobrightness is off. When i first got the iPhone the brightness was like everyone elses.
i only use the official charger. I think there may be a problem with the voltage or the electricity in my home as all my iPhones have had this problem. Im not sure when the change happens but the something is damaging the backlight of my iPhones. No idea what.
Please can some one with the same issue or knowledge of physics please help me. I dont want to keep having this issue. I also have a Macbook pro and am fairly sure its happned with this also but have no means of comparison as I dont know any one else with one that comes to my apartment.
Regards
FahadThe iPhone 5 has full Warranty. Make Genius reservation and take to Apple Store. Show the Genius the problem and they will replace your iPhone 5 with a perfect iPhone 5 without problems. If some of iPhone 5 have this problem, it does not matter, Apple makes millions of iPhone 5, some are going to have a problem. When the Genius gives you the new replacement iPhone 5 test it out in the Apple Store before you leave, so you are happy and do not waste anymore of your time.
-
Low voltage (vddq) please help (k7t 266pro2ru
I have just bought a new grapohics card (ASUS V84400 DELUXE GEFORCE 4 TITANIUM 4400) and the program Smart Doctor (included with th graphics card) warns me that my vga card voltage 1.5 is out of safe bound and that my moterboard does'nt supply with reliable 1.5 voltage. Please help me!!!!! I run my graphics card under 4x. Please Help!! ;(
hi
what psu do you use make model
what are its max amps at 3.3 and 5 volts
note not the peak figue which is higher
normally on a sticker or plate on the psu -
P7N Diamond - Voltages all greyed out? - Please help
Hi I have the following
I have just flashed my P7n to 1.16 bios using the flashing tool. I want to change the Memory Voltage to 2.10v as per spec but all the voltages are greyed out in the bios. Please help.
I am running -
P7N Diamond with a Q6600
4 gigs of Corsair DDR2 XMS2-6400C4
8800 GT
and a 550watt PSU
Any help would be most welcome!
Thanks
PaulhSorry Guys,
Just read the thread below, problem solved.
Thanks
Paulh -
Problem Building stable a PC - PLEASE HELP
I managed to get the following system for an affordable price.
1. Processor : AMD Athlon64 2800+
2. Motherboard : MSI K8N Neo2 (MSI 7030) motherboard
3. DDR400 RAM: Kingston KVR400X64C3A/512
4. Power Spply : Targa Tech LC-450E
+3.3V / 28A
+5.0V / 50A
+12V / 18A
-5.0V / 0.8A
5. Graphic : MSI FX5500-TP256
5. DVD Combo : MSI X52P
6. HDD : Western Digital WD-800 80MB SATA
After assembling the pc and install WinXP SP2 and all the supplied driver. I still encounter these problems.
1. Unintentionally shutdown of application/games after a few moment.
2. Unintentionallly reboots of PC especially while testing 3D games/Benchmark.
3. Constant blue screen
II suspect a misconfigured BIOS or insufficient power supply. Hope all of u techie out there can help..PLEASE HELP. I am not those highly technical person.
Can anybody recommend me the BIOS setting suitable for my pc.hi anjebat,
welcome to the forum
1) Enter Bios
2) Cell Menu
3) Memory Voltage = Auto ---> 2.6
4) Dram Settings
5) CAS# Latency (Tcl) Auto --> 3
6) RAS# to CAS# delay (Trcd) Auto --> 3
7) Min RAS# active Time (Tras) Auto ---> 8
8) Row Precharge Time (Trp) Auto --> 3
From pinochio's post see
KVR400X64C3A won't run at 400MHz
if it still gives problems :-
3) Memory Voltage = 2.6 ---> 2.7
If you still have problems
Memtest86+ - Advanced Memory Diagnostic Tool - Test each module in slot1. if both ok test both slots 1&2
To help with bios settings
Bios Guide
Power supply is marginal but may work if you don't add to many devices.
good luck -
PLEASE, PLEASE HELP ME. I'm a computer ignorant woman and need help. I have an IBOOK G4 and I was trying to fix a problem in IPhoto (which never got fixed) and took some guy's bad advice to reset iphoto or something and now my plug-ins are gone too. Or at least the one(s) that were allowing me to listen to on-line discussions and audio recordings.. Can anyone help me? I have gone to UPDATE SOFTWARE and updated Java but that is all. It's like I go to a think were there is an audio thing to listen to and there is a picture of a plug in and it says something like "Plug in not available to listen to this" and then gives you an option to download plug-in but when I do, it says something like "No Plug in was found that was useable" or something alone those lines. Then it has a manual plug-in option but when I clicked that, I entered the frustrated crying zone. Can you help? I will so give you big points! Thank you!
THis is all Greek to me, but maybe it answers your questions???? Thank you Ronda.
ATA Bus:
MATSHITADVD-R UJ-845E:
Model: MATSHITADVD-R UJ-845E
Revision: DMP2
Serial Number:
Detachable Drive: No
Protocol: ATAPI
Unit Number: 0
Socket Type: Internal
Built In Sound Card:
Devices:
Texas Instruments TAS3004:
Inputs and Outputs:
Internal Microphone:
Controls: Left, Right
Playthrough: No
PluginID: TAS
Headphones:
Controls: Mute, Left, Right
PluginID: TAS
Internal Speakers:
Controls: Mute, Left, Right
PluginID: TAS
Formats:
PCM 16:
Bit Depth: 16
Bit Width: 16
Channels: 2
Mixable: Yes
Sample Rates: 32 KHz, 44.1 KHz, 48 KHz
PCM 24:
Bit Depth: 24
Bit Width: 32
Channels: 2
Mixable: Yes
Sample Rates: 32 KHz, 44.1 KHz, 48 KHz
DIMM0/BUILT-IN:
Size: 512 MB
Type: Built-in
Speed: Built-in
Status: OK
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 6
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 6
Dynamic Power Step: Yes
Reduce Processor Speed: No
Automatic Restart On Power Loss: No
Wake On AC Change: No
Wake On Clamshell Open: Yes
Wake On LAN: No
Wake On Modem Ring: Yes
Display Sleep Uses Dim: Yes
Battery Power:
System Sleep Timer (Minutes): 9
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 9
Dynamic Power Step: No
Reduce Processor Speed: Yes
Automatic Restart On Power Loss: No
Wake On AC Change: No
Wake On Clamshell Open: Yes
Wake On Modem Ring: No
Display Sleep Uses Dim: Yes
Reduce Brightness: Yes
Battery Information:
Battery Installed: Yes
First low level warning: No
Full Charge Capacity (mAh): 466
Remaining Capacity (mAh): 466
Amperage (mA): 0
Voltage (mV): 16491
Cycle Count: 247
AC Charger Information:
AC Charger (Watts): 50
Connected: Yes
Charging: No
Hardware Configuration:
Clamshell Closed: No
UPS Installed: No -
My MB is always starting up in safe mode... why? What to do to start-up normally? Please help.
Hi,
I am frequently having troubles with my MB. Different types of troubles. Couldn't solve a single one yet.
I have performed reboot MB in safe mode-- hold down the left shift key after the start up tone till the spinning gear appeared.
Few hours back i performed that, and since then it just starting up in safe mode without holding the any shift key. I have password protected log-in and each time the dialog box shown the safe mode, not the normal boot as it used to be. I restarted so many times, but same result.
I started-up by holding down the Option key, dialog box showing the same thing "safe mode" and same result.
I started-up in single user mode, and then typed reboot, then pressed enter/return button, but dialog box shown the same and it started up in safe mode after entering the password.
While in the safe mode, i have selected the Mac OS X 10.4.11 from the preference pane, then restarted, but all produced the same result, same dialog box showing the safe mode.
I couldn't take the screen shot of that dialog box that appears before starting up.
I am currently using the internet while in safe mode, and using ethernet adapter- a AirStream 1100 F25 external modem attached to the USB port. I don't know if that is good for my MB to use internet on the safe mode.
I used disk utility and verified the disk during the safe mode, i don't know if that is right or wrong to perform that utility in safe mode, but it all appeared as normal. You can see that from the following image.
Few days back, i performed the disk utility to verify disk while on the normal boot. But the result shown the red marks, please see the following image for details.
Hardware Overview:
Model Name: MacBook
Model Identifier: MacBook2,1
Processor Name: Intel Core 2 Duo
Processor Speed: 2 GHz
Number Of Processors: 1
Total Number Of Cores: 2
L2 Cache (per processor): 4 MB
Memory: 1 GB
Bus Speed: 667 MHz
Boot ROM Version: MB21.00A5.B07
SMC Version: 1.13f3
Serial Number: 4*********M
Sudden Motion Sensor:
State: Enabled
BANK 0/DIMM0:
Size: 512 MB
Type: DDR2 SDRAM
Speed: 667 MHz
Status: OK
BANK 1/DIMM1:
Size: 512 MB
Type: DDR2 SDRAM
Speed: 667 MHz
Status: OK
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 10
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 10
Automatic Restart On Power Loss: No
Wake On AC Change: No
Wake On Clamshell Open: Yes
Wake On LAN: Yes
Display Sleep Uses Dim: Yes
Battery Power:
System Sleep Timer (Minutes): 5
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 1
Wake On AC Change: No
Wake On Clamshell Open: Yes
Display Sleep Uses Dim: Yes
Reduce Brightness: Yes
Battery Information:
Battery Installed: Yes
First low level warning: No
Full Charge Capacity (mAh): 2745
Remaining Capacity (mAh): 2745
Amperage (mA): 133
Voltage (mV): 12575
Cycle Count: 507
AC Charger Information:
Connected: Yes
Charging: No
Hardware Configuration:
UPS Installed: No
Intel ICH7-M AHCI:
Vendor: Intel
Product: ICH7-M AHCI
Speed: 1.5 Gigabit
Description: AHCI Version 1.10 Supported
TOSHIBA MK1234GSX:
Capacity: 111.79 GB
Model: TOSHIBA MK1234GSX
Revision: AH008B
Serial Number: Z6M7T4FTT
Native Command Queuing: Yes
Queue Depth: 8
Removable Media: No
Detachable Drive: No
BSD Name: disk0
OS9 Drivers: No
S.M.A.R.T. status: Verified
Volumes:
Macintosh HD:
Capacity: 111.47 GB
Available: 24.09 GB
Writable: Yes
File System: Journaled HFS+
BSD Name: disk0s2
Mount Point: /
TOSHIBA MK1234GSX:
Capacity: 111.79 GB
Model: TOSHIBA MK1234GSX
Revision: AH008B
Serial Number: Z6M7T4FTT
Native Command Queuing: Yes
Queue Depth: 8
Removable Media: No
Detachable Drive: No
BSD Name: disk0
OS9 Drivers: No
S.M.A.R.T. status: Verified
Volumes:
Macintosh HD:
Capacity: 111.47 GB
Available: 24.09 GB
Writable: Yes
File System: Journaled HFS+
BSD Name: disk0s2
Mount Point: /
System Software Overview:
System Version: Mac OS X 10.4.11 (8S2167)
Kernel Version: Darwin 8.11.1
Boot Volume: Macintosh HD
Please help me out. Let me know how to start-up normally. By the way, my superdrive is not detecting DVDs including the OS dvds, but it read and write the CDs. So, It is not possible to reinstall OS early, at least not before the having the back up of the data. Please help me with contingency plan/s or as you think fit.
Thank you. Look forward to your reply.
<Personal Information Edited by Host>Maximillianmann,
depending upon how full “almost full” actually is, that could be the problem.
You can try this, if you have Mac OS X 10.7 or newer installed, to see if it’s not related to your disk being almost full: boot your MacBook Pro into Recovery mode by holding down a Command key and the R key as it starts up. Once the Mac OS X Utilities menu appears, select Disk Utility. On the left-hand side of the Disk Utility window, select your internal disk’s boot partition (typically called “Macintosh HD”). On the right-hand side, press the Verify Disk button if it’s not greyed out; if it is greyed out, or if it reports that errors were found, press the Repair Disk button. Once the verification/repair is completed, exit Disk Utility and select Restart from the Apple menu to restart in normal mode. Once you hear the startup chime, try booting into Safe mode; does it let you do so now? -
Cannot install windows, starting to get really pissed off with this PLEASE HELP
ok, i'm starting to get agitated with this.
i cannot install windows XP, 2003, OR Longhorn on my machine.
right now, i have the following setup:
msi 865pe neo2 motherboard
intel p4 3.2ghz w/HT (factory HS/Fan currently)
1 dimm of PC3200 crucial DDR400
30GB maxtor HD plugged into primary IDE
pioneer dvd/cd drive as sencondary IDE
alps 3.5" floppy drive
antec true blue 480wt PSU
i do the following:
format with maxtor cd
boot from OS cd
start setup, reboot, continue
the farthest i can get is 'registering components/completing installation' i either get a blue screen stop error which isnt the same everytime, or it just locks up and doesnt do anything.
ran the memtest checker and get errors on test #4
i had a DIMM of kingston that gave the same errors, so i RMA'd it and got another. same errors, so i RMA'd again and got a Crucial stick. same errors.
so i RMA'd the motherboard since i figured it had to be that. and it improved from the problems i had earlier. (the problems i had before were worse before.)
below are my BIOS settings. SOMEONE WHO KNOWS PLEASE HELP ME!
advanced bios features:
quick boot - enabled
boot order - floppy, cd, HDD
full logo - disabled
s.m.a.r.t - enabled
num-lock on boot - enabled
floppy swap - disabled
floppy seek - enabled
save rom to HD - no
boot to os/2 - no
hyper threading - disabled
mps revision - 1.4
apic acpi sci irq - disabled
cpu l1 & l2 cache - enabled
bios cacheable - disabled
c000, 32k shadow - disabled
advanced chipset:
dram timing...
configure by spd - enabled
(i dont know what to set timing to, nothing anyone has since said helps)
integrated perfs:
usb controller - enabled (same errors if its disabled too so its not USB)
usb device legacy support - disabled
on chip IDE:
operate mode - legacy mode
ata config - pata only
sata keep enabled - yes (for sata drive i have, error either way)
pata channel selection - both
onboard ethernet, 1394, prmoise ide and audio all DISABLED
pc healt status:
cpu - 49°C/120°F (idle sitting in bios)
system temp - 28°C/82ºF
cpu fan - 2678rpm
nb fan speed - 6490rpm
vcore - 1.456 up to 1.502
3.3v - 3.232v
+5.0v - 5.003v
+12v - 11.680v
-12v - -11.743v
-5.0v - -4.826v
battery - 2.896v
+5V SB - 4.945
freq/voltage control
Dynamic OC - disabled
cpu ratio locked
dram freq - auto
spread spectrum - enabled
cpu bus clock - 200
ddr clock (grayed out) - 400
adjust agp/pci - 66.66/33.33
cpu vcore adjust - no
cpu vcore (grayed out) - 1.5500v
ddr power voltage - 2.65v
agp power voltage - 1.50v
SOMEONE PLEASE HELP ME!!!!!
i'm running out of time, money, patience.
if it cant be solved i'm going to set myself on fire!Quote
Originally posted by REILLY875
Do NOT try the 250 Watt PSU!!, As "Wonk" said if you happen to Blow it, the PSU will most likely Take out the Mo-Bo with it! And maybe the CPU to, due to the Voltage Spike you would get ...I would not put to much Credence into the fact that as of now the +12V and the +3.3V Rails are reading a little low,(I say this because it is indeed a ANTEC), as this could be the Monitoring Hardware, or the Software that might be reading wrong....If I where you I would First set the Memory Timings Manually to 3-4-4-7-8, And up the DRAM (VDIMM) Voltage to 2.7 Volts, and if it still wont Load, I would Definitly try a different DIMM Slot, and Rince and Repeat .....If you dont mind me asking , Why are you running with just 1 Module?....Is it on purpose or are you saving up for More?................Sean REILLY875
yea, i dont plan to run the 250. im gonna wait for the new 480.
thanks for the info about ram timings as well. i havnt gotten any solid answers about what to set it to.
even with new mobo and ram, i'm getting errors in memtest86 #4 test as i always have. i've tried different slots with same problems.
i only have one module because i dont want to waste anymore money on a non-working system. once i get it up and running i'll add another 512. -
790FX-GD70 Ram Problem (PLEASE HELP!!)
Hello all,
I recently installed my 790FX-GD70 motherboard with all the ram and all that
I have 2x4gb RAM but when i put both sticks of ram in i do not get anything on the screen but when i install 1 stick of ram into the 2nd dimm windows loads up and all that but after like 10-15minutes i get a blue screen and at the bottom it says "Dumping Physical Memory to Disc" then it reboots loads back to windows and does the same thing again, but i dont know why when i put 2x 4GB ram the same the computer boots up but nothing comes on the screen.
Any help please?
Really need to fix this.
750W PSU
AMD phenom II 850 @ 3.3GHz
2x4gb ram only 1 allowed
2x ASUS GeForce 550TI's
PLEASE HELP ME!!
Nothing is overclocked.Hello Sorry here are the links to my PSU and RAM!
PSU:
http://www.ebay.co.uk/itm/NEW-QUIET-ARTIC-750W-ATX-PSU-8-PIN-SATA-PCI-E-PFC-120mm-FAN-POWER-SUPPLY-/140722519305?pt=UK_Computing_PowerSupplies_EH&hash=item20c3b73d09#ht_3045wt_1012
RAM:
MTEX 1333MHz-----1111G14JCJ6-----MTC003944
I got these numbers of the ram itself so i don't know which is the model number and the serial number.
And the voltage of the ram is at default. 1.5 i think
I did try and set the voltage to 1.8 and put my 8gb ram in, it booted up to windows and i managed to put 2 sticks of ram in then about 10 minutes later it went to blue screen again and said dumping physical memory to disc
I done a error check of the ram and it came up with no errors. -
I really don't know what else to do anymore i've tried everything! i saw i tried re installing itunes I downloaded quicktime but whatever i try i can't sync any videos into my itunes 11 as in there is nothing I click "Open" like how i usually sync things and then clicked on the video. after that the little window will just dissapear and nothing happens, i'm serious i tried looking for it in the recently added, in the music, in the movies, TV shows, home videos nothing i can't find it anywhere and i know that i SHOULD be able to synce those videos because i synced those videos before. please help me I'm losing my mind!
Generally i found this thread because i've also got troubles with coax output my problem is in choppy sound with scratches and clipping in Windows 7, when i try to play Dolby Digital or DTS audio in movies or even test sounds from speaker control panel. In win xp all works fine - and in win7 only pcm stereo can normaly being output.
I try with different drivers (official and from daniel) and nothing helps...
yep...bios of my motherboard was configured to lower CPU ratio and voltage when idle (C1E option). I turn this option off and all works fine now) -
please help. ive bought a second hand ipod nano, when i connect it to my pc, it does not recognise it in itunes,yet it comes up as a sigma mass usb device. its an ipod nano 8gb?. im running on windows vista,my own ipod classic runs fine.
there is a good chance that this can be related to bad contact in USB lead.. e.g not enough power from IPOD to PC so that pc cannot recognise it. Where I work I get alot of USB devices on pc's that are not recognised and most of the time it is the connection to the device that is not good enough because the flat end of the USB adapter has been gradually bent over time just slightly and now contact is not good. It can also be todo with drivers or If you are using it through a USB hub.
so if it is not working through USB hub try direct. also try in back of PC as these Ports or direct access to main board to pc and would be less trouble some if there was a voltage loss from mainboard in pc to front of unit. -
URGENT (PLEASE HELP) AC Analysis Matrix Singular Error
Hi all (sorry to post on a new thread again Yao) , my project is due tomorrow at 9 am. Therefore please please please help me on this circuit.
I can't perfom AC analysis on the circuit for that there is a matrix singular error. May anyone please tell me what is wrong ??
Please! Thank you!!!
Attachments:
489project2.ms10 105 KBOK, I added a current probe to measure the current thru the multimeter (You could also use a current - controlled voltage source) but no matter what I look at I can't get an ac analysis to give a non-zero gain. I simplified the circuit some more and set the option for the node numbers to show. There is something fundamentally wrong in the area of the ac voltage source V1 and the voltage controlled capacitor. As long as the voltage source is in parallel with the capacitor, the capacitor current will be driven only by the voltage source. The capacitor voltage will always be equal to the voltage source V1. The current source A4 doesn't accomplish anything - its current will just be sunk into the voltage source V1. I thought maybe you really meant to measure the voltage controlled capacitor current and feed that back into one of the inputs of A4 but I can't really tell what you are trying to accomplish. Maybe this will give you some ideas.
Attachments:
489project2r1.ms10 82 KB -
PLEASE HELP!!what is the function of this keithley output source VI?
i would like to know what does "trigger delay","sour delay","NPLC","arm count" do in this example.Please help!! thanks!!=D!!
Attachments:
24xx Swp-I Meas-V gpib.llb 687 KBI didn't open your example (I'm not at my work computer), but here is an explanation of the terms:
Trigger delay is the amount of time between a DMM being given a command to take a reading, and the actual reading being taken. Lets say you want to read the voltage on line A exactly one second after the voltage on line B goes above 2V. You set the DMM for external trigger with line B connected to the external trigger input on the DMM. THen set Trigger Delay for 1 second. Then send the command to read the DMM (Read?). The DMM will become armed (waiting for trigger). When line B goes above 2V, the DMM will wait one more second, then read line A. If you don't want to wait to take a reading, set the trigger to immediate.
Sour stands for source. I've never heard of source delay.
NPLC is the Number of Power Line Cycles. In the U.S., we use 60Hz power (50Hz in Europe), so one power line cycle is 1/60 seconds. When setting NPLC, the DMM will take continuous readings for that length of time, then take an average of all the readings and return this value. Setting NPLC to 10 will make the DMM take readings ofr 10/60, or 1/6 seconds, and return the average of all readings. How many readings can be taken during that time interval depends on the DMM, the range setting, and the resolution setting.
Not sure about "arm count", but "arm" means that the DMM has been given a command to read but has not yet received the trigger to take the reading.
Reading a DMM through GPIB involves a series of events: Arming (GPIB command to read or measure), triggering (immediate or delayed, internal or external), measuring (one measurement or several for averaging), then returning the measurement.
Message Edited by tbob on 05-29-2006 11:54 AM
- tbob
Inventor of the WORM Global -
Please Help! MBP shutting off when plugged in, now not recognizing MagSafe Adapter
I started seeing this problem a few weeks ago, my MacBook Pro just shut off spontaneously while watching a video full-screen. I turned it back on and the problem went away for a while. But now, the shut-downs happen more frequently. It doesn't matter if the MBP is running off of the battery or if its running off of the AC cord, it will just shut off. No warning. No standard shut-down process, everything just stops and a balck screen shows up. After it shuts off, it takes a few seconds to get it to restart, and when it does, the computer's date and time will be reset to some date in 2000. Very strange, I've had this computer for a year and I know people with the same model that have had no such problems. The battery is at 168 cylces (I use this for school, so it was being used everyday throughout the last two semesters), and the Condition is listed as Normal in the System profiler, so I doubt the problem is with the battery, but I could be wrong. I've seen posts about the RAM/PRAM causing the date/time resets. Nevertheless, the MBP has been running normally on the battery, battery life is still the same length of time as it was when I first got the computer, and runs smoothly. Up until last night, the AC MagSafe Adapter was still working, so I only used that as the power source. Everything was fine, but the MBP shut off once or twice while it was plugged in within the last month or so, but the AC would still have a green light, indicating the computer was still recognizing the power source. Now, I can't get the MagSafe to be rocognized at all. The computer is running on battery only, and I've tried resetting the SMC, but I'm unsure if it worked since the MagSafe is still unrecognized. When its plugged in, the System Profiler says it is not connected and not charging.
I'm running on Mac OS X 10.6.8, a 2.4 GHz Intel Core 2 Duo, with a 4GB memory (of which less that half is used). Computer usage is low, so its not like I'm running several programs at once, at most, its two or three at a time, for short periods. My MBP is a 13" aluminum body, doesn't seem to be overheating, has worked fine after long periods of being on and getting hot, I always let it cool down after I feel it getting too warm.
Please help if you can! Thank you!Battery Information:
Model Information:
Manufacturer: DP
Device name: bq20z451
Pack Lot Code: 0000
PCB Lot Code: 0000
Firmware Version: 0201
Hardware Revision: 0002
Cell Revision: 0164
Charge Information:
Charge remaining (mAh): 2037
Fully charged: No
Charging: No
Full charge capacity (mAh): 5078
Health Information:
Cycle count: 168
Condition: Normal
Battery Installed: Yes
Amperage (mA): -917
Voltage (mV): 11235
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 10
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 5
Wake On AC Change: No
Wake On Clamshell Open: Yes
Wake On LAN: Yes
Display Sleep Uses Dim: Yes
Battery Power:
System Sleep Timer (Minutes): 5
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 1
Wake On AC Change: No
Wake On Clamshell Open: Yes
Current Power Source: Yes
Display Sleep Uses Dim: Yes
Reduce Brightness: Yes
Hardware Configuration:
UPS Installed: No
AC Charger Information:
Connected: No
Charging: No
thanks for the quick reply~ -
I have a ram problem, can somebody please help me?
Hello
This is the first time I've put a computer together from scratch (I got some help from a friend though). What I wonder is if there is a manual for the MSI mothercards somewhere on the net because I didn't get any good description in the package, and I can't find the spot for audi and USB inputs. I also would like to know how many memorysticks i can use, because if i put in 3 of them the computer starts to beep. Can somebody please help me?
My specs are:
Q-tec midi Tower
MSI K8N Neo2-FX, nForce3
AMD Athlon 64 3200+ 2.0GHz socket 939
Zalman P4 CNPS-7700-CU
XFX Geforce FX5500 128MB DDR
Samsung Spinpoint P120 200GB
Sony DVD burner DL
Sony floppydisk
Cosair Value S. PC3200 DDR-dimm 512MB unbuffered non-Parity, 64Meg x 64, CL2.5
(I have 3 of these but I can only have 2 at a time or the computer wont work)
// TheGamecriticQuote from: TheGamecritic on 15-September-05, 18:42:56
Hello
This is the first time I've put a computer together from scratch (I got some help from a friend though). What I wonder is if there is a manual for the MSI mothercards somewhere on the net because I didn't get any good description in the package, and I can't find the spot for audi and USB inputs. I also would like to know how many memorysticks i can use, because if i put in 3 of them the computer starts to beep. Can somebody please help me?
My specs are:
Q-tec midi Tower
MSI K8N Neo2-FX, nForce3
AMD Athlon 64 3200+ 2.0GHz socket 939
Zalman P4 CNPS-7700-CU
XFX Geforce FX5500 128MB DDR
Samsung Spinpoint P120 200GB
Sony DVD burner DL
Sony floppydisk
Cosair Value S. PC3200 DDR-dimm 512MB unbuffered non-Parity, 64Meg x 64, CL2.5
(I have 3 of these but I can only have 2 at a time or the computer wont work)
// TheGamecritic
Congrats on 'Rolling your Own' for the first time. I'm certainly no expert although I have sucessfully built a few. Actually, my specs are almost identical except I'm using Kingston Value Ram instead of Cosair. As far as your first question, I assume you mean the internal USB/MB connectors and the MB audio connector(s). The information is in the MSI Neo2 Plat manual although you have to look closely and move back and forth between the MB schemaic and the section(s) describing the connections to get a clear fix. The MB USB connectors are on the side of the MB furthest from the RAM slots and about in the center, (JUSB1 or JUSB2). The audio connector (JAUD1 is located on the same side of the MB as the USB connectors only near the rear panel end, (close to the orange PCI slot). As you, I found that that I could not use three ram sticks as I could in my old K7 board and when I bought two sets of matched ram I found that it didn't like 4 sticks either. Three: Would'nt post Four: Instability and an initial hit in performance; although I was able to finally coax it to 200mhz Dual Channel it wasn't worth it because of the random crashes n Windows I was getting. I have also discovered the hard way that for some reason my board at least is hypersensitive to IDE cables, (Would not recognize any secondary IDE device on Channel 1 until I found the right cable) and it does not like Sound Blaster audio cards prior to Audigy 2 ZS. Actually, it only tolerates a ZS and I had problems and it didn't like my new X-Fi at all until I moved it to the PCI slot closest to my video card. I was getting random BSODS and crashes, (one that took out my OS). Since I move the card things appear to be more stable, so far. Anyway good luck.
Maybe you are looking for
-
How can I get user to enter date & time on a form?
I have a form where I want the user to enter a date and time for an event. The database field is in MYSQL datetime format I've used the datepicker on the form field but it only allows for a date entry not time.(eeven when seetin the width to 22 chars
-
A135-S4527 Host Process for Windows Services stopped...
I have started getting a Windows error: Host Process for Windows Services stopped working and was closed. Laptop runs fine except my network connection says Connection Status: Unknown The service to detect this status is turned off and McAfee stoppe
-
Roaming Profile are not stored completely
Hello NG In our environment we work with NWClient 2 SP1 IR9, ZCM11 SP1a and Roaming profile is activated by a ZCM policy. Now we have the problem, that when a user logout from the workstation, the roaming profile is not stored completely to the home
-
HT201263 how to fix error 9 for recovery
How do I fix error (9) for recovery in i tunes?
-
Cross company incoming payment
we use F-28 to process inter-company USD incoming payment, (customer is in another company code, but both two company use same local currency JPY), the problem is when we enter cash discount, it will generate line item and defaulted to discount accou