Please help: Internet Setup Problems.

So here's the deal. I am trying to connect to the internet through a ethernet cable. I follow everything by the book while setting it up.
I click on System Preferences and go to Network and it says "Ethernet is currently active...and the internet is connected via built-in ethernet." But when I click on Safari, it says I am not connected to the Internet.
I run Network Diag and I get a green light for Ethernet, Network Settings, and ISP, but a red light for Internet and Server.
Any suggestions?
I have tried reseting the modem and all that. The cables are fine. They work on my other computer.

Could be a lot of things, but we'll try some simple things first. If you are connecting directly to your modem and not through a router, then shut down your computer and unplug the modem for 30 seconds. Then, plug in your modem and let it go through it's intialization sequence (the lights blink). When all the lights are reasonable steady, about 30 seconds after plugging it in, plug the Ethernet cable into your computer and boot it up. I know you did this already, but that 30 second wait is sometimes the key.
Now, if that doesn't work, then shut everything off again. Plug in your Ethernet cable to the computer and start it first. Let everything get settled (hopefully that 30 seconds) and then plug in your modem and let that get settled and see what happens.
Now, if it still doesn't work and you're getting an IP address assigned, what does it start with?

Similar Messages

My Itunes is no longer allowing me to manage my music on my phone i can no longer select on my iphone to make playlists and delete music. Please help fix my problem.

My Itunes is no longer allowing me to manage my music on my phone i can no longer select on my iphone to make playlists and delete music. Please help fix my problem. Iphone4s, 32gigs, IOS 7.1.2
I don't know why it stopped working but it happened a month or two ago but the option on this phone that's usually all the way to the left when you select your device but now its not and I don't know what caused it. ive already tried troubleshooting my problem but have found no help.

Hello Salmomma,
Thank you for the details of the issue you are experiencing when trying to connect your iPhone to your Mac. I recommend following the steps in the tutorial below for an issue like this:
iPhone not appearing in iTunes
http://www.apple.com/support/iphone/assistant/itunes/
Additionally, you can delete music directly from the iPhone by swiping the song:
Delete a song from iPhone: In Songs, swipe the song, then tap Delete.
iPhone User Guide
http://manuals.info.apple.com/MANUALS/1000/MA1658/en_US/iphone_ios6_user_guide.p df
Thank you for using Apple Support Communities.
Best,
Sheila M.

[ETL]Could you please help with a problem accessing UML stereotype attributes ?

Hi all,
Could you please help with a problem accessing UML stereotype attributes and their values ?
Here is the description :
-I created a UML model with Papyrus tool and I applied MARTE profile to this UML model.
-Then, I applied <<PaStep>> stereotype to an AcceptEventAction ( which is one of the element that I created in this model ), and set the extOpDemand property of the stereotype to 2.7 with Papyrus.
-Now In the ETL file, I can find the stereotype property of extOpDemand as follows :
s.attribute.selectOne(a|a.name="extOpDemand") , where s is a variable of type Stereotype.
-However I can't access the value 2.7 of the extOpDemand attribute of the <<PaStep>> Stereotype. How do I do that ?
Please help
Thank you

Hi Dimitris,
Thank you , a minimal example is provided now.
Version of the Epsilon that I am using is : ( Epsilon Core 1.2.0.201408251031 org.eclipse.epsilon.core.feature.feature.group Eclipse.org)
Instructions for reproducing the problem :
1-Run the uml2etl.etl transformation with the supplied launch configuration.
2-Open lqn.model.
There are two folders inside MinimalExample folder, the one which is called MinimalExample has 4 files, model.uml , lqn.model, uml2lqn.etl and MinimalExampleTransformation.launch.
The other folder which is LQN has four files. (.project),LQN.emf,LQN.ecore and untitled.model which is an example model conforming to the LQN metamodel to see how the model looks like.
Thank you
Mana

HT5312 i forgot my secret question, please help me this problem. Thanks

I forgot my secret question, please help me this problem. Thanks

Contact iTunes Customer Service and request assistance
Use this Link > Apple Support iTunes Store Contact
And/or see the More Like This section on the right.

Please help with slideshow problems!

Am using Photoshop Elements 8 and trying to make a slideshow. Have tried 4 times now and keep ending up with same problem, cannot reopen project to continue edititing. Won't show up in orginizer and when I find on harddrive and try to open get message " wmv file cannot be opened". How can I save a
slideshow inprogress and be able to reopen and continue to edit and make slideshow? I want to thank anyone who can help me with this in advance as I
have gotten so frustrated that I want to just scream.
Thanks

Thanks for the help, thought I had done so but maybe not. Anyway will have another go at it, now may I ask another
question? I am trying to add audio to slideshow. I have some music I purchased thru amazon as mp3 files but I get
message no codec and when I try to add wmv I get same message. What type of file do I need and how can I add
multiple songs to one slideshow. I have one little wmv file that will go in, but it just replicates itself multiple times until
it fills slide show.
Thanks again, sorry to be a bother, but this thing is driving this old man crazy.
Date: Sun, 26 Dec 2010 20:34:32 -0700
From: [email protected]
To: [email protected]
Subject: Please help with slideshow problems!
You need to save the slideshow project in order to be able to go back later and make changes or additions to an existing slideshow . The wmv file is a final output format.
Now you are most probably using only the Output command: that is what makes the wmv file.
You should also do the Save Project command. (and I make it a practice to do the Save Project command before I do the Output command).
If you look at the Elements Organizer 8 Help, there is a topic on "Create a slide show".
-- Very close to the beginning of that topic is a screen shot of the Sldie Show Editor screen,
-- The bar below the usual menu bar is labeled with a "B" and called the Shortcuts bar.
-- The 1st entry on that Shortcuts bar is "Save Project"
It is the Save Project command that saves the information about which photos, audio, etc you placed in that specific slide show so that you can come back again to do subsequent editing. Save each Project with a unique name.
After completing the Save Project command, you shoud see an "icon" in the Organizer for that slide show.
Note: you must also keep the photo files and audio files which you have used in this slide show: you can't delete them because the project file does NOT contain a copy of the photos, it only has the identification and folder location of the photo and audio files.
>

PLEASE HELP - COLOR SHIFTING PROBLEM on output NTSC monitors

http://www.smmlv.com/testproject/
Above is a link to a layered photoshop file that has a USA map and over a dozen network overlays used in a section of our video. I animate each layer on sepeartely in the video and have noticed a major problem recently, the color of the art does not hold true to placement. I created the art originally in Illustrator and then converted the file to Photoshop at 640x480, 72dpi. This has always worked perfectly in the past to display and animated artwork in FCP.
Right now, in FCP I am using the NTSC DV 3:2 frame size, and the compressor of DV/DVCPRO - NTSC. I have a JVC Profressional DV deck that hooks up through firewire and sends S-Video to my monitors. This setup has always given me a great picture even though it is not completely upcompressed. Using these settings and this art, the color lines on this map in red, light blue, yellow and purple all have a "color shift" to the left about 5 pixels. It makes it appear that the line is where it is in the file, but the color overlaying the line is offset to the left 5 pixels and transperant to about 50%. This occurs only when viewed on some TV's and NTSC monitors and projectors. The strange thing is, some monitors display the color aligned almost perfectly on these maps and other monitors and projectors show this "digital halo" of color shifting really bad. If I take the layered network overlays in these colors and color tint them to black or grey, white, light green, or even light orange, they no longer have the color shifting and the detail is perfect.
Is there any way to fix this problem? I have tried duplicating the sequence and setting the compressor to 8bit Uncompressed, and while my captured footage is not this compression, in theory the art should render at this higher resolution setting. This did nothing to solve the problem.
I also have tried using different Broadcast safe and Y/C corrector filters with different results. The Y/C filter allowed me to reposition the color problem and thus removing most of the problem, but also removing most of the color. Nothing else has allowed me to seemingly move the color into the proper possition.
What is causing this color shift on the displayed NTSC image?
In FCP 4.5 I can see my rendered video in the program viewer screen and besides the pixel compression appearing on the lines, overall the video looks great paused or even better when playing. Then you view it through my deck onto my Pro Sony NTSC 19" color monitor and it also appears great, with a slight color halo to the left of these colors, but the color in the lines are there. If you are a few feet from the screen and know what you are looking for you might see it, but doubtful. Then you view it using the same signal on a 17" Samsung TV and the color shifting makes the map and other art, like the clients blue logo, look horrible, with each color line appearing twice and offset left from each other as if you had double vision. Normally I would think it is the TV causing this, but then we tested this same movie on 2 differnt projectors. The $700 Epson projector displayed everything beautifully, again with only the slightest color halo to the left, but then the Panasonic $4000 projector made everthing in these colors look double vision again. What is going on???
One more thing to keep in mind, my color bars also show this problem with these colors as well as shot footage of these facilities. There are tall red poles in the shots and everything displays fine except for the red pole color looks like it's glowing off the pole to the left.
PLEASE tell me there is a solution to this.

I have tried Degaussing, using filters, changing cables, and testing other monitors and systems on these monitors, everthing I can think of to solve the issue. Is it FCPo or is it the monitors?... or is it a signal strength thing. Can monitors and projectors shift color when the signal is read from a DVD or Mini DV Deck? Is there a fequency difference (Ie: 75mgz or 80 mgz) that might be causing the shift in some monitors and not so badly in others. But if this was true, how would some DVD's (like Baby Einstein DVDs that use really bright colors) display red and blue perfect using these same player and monitor, while my projects is shifting color? Doesn't that rule out the signal from the DVD player if other DVD's do not have this issue?
I have uploaded the original art used, an exported .jpg file from the FCP timeline and sample photos of 2 different monitors to show to show this problem as best I can. http://www.smmlv.com/testproject/
Someone out there must have had this problem before. There's no way a color shift problem like this with Mini DV has gone on this long without someone seeing it.
One last thing about what I have tried... I do understand that with editing in Mini DV instead of uncompressed or HD video I lose a bit of resolution (4:2:2) and I see this compression occuring in some of the areas in the video where these problems persist. But, I did remake the art and rerender this project in an 8bit uncompressed settings and then displayed that up on the screen and I get the same color shift. I keep going in circles trying to find the culprit that is causing the delema.
PLEASE HELP! There are large tours going through our facilities daily and the large screen projector is displaying this problem as well. Let's just hope they don't notice and that their TV's at home or office does not display it on our final DVD's made.

Please help, color printing problems.

I have snow leopard and just bought a new HP officejet 7500 wide format wireless all-in-one. The problem is when I Print from my boyfriend's PC, the pictures are fine but when I print from my imac, the image I see on the monitor isn't what is printed. The colors are off and the picture is way too dark. I've looked on the internet to try to find a solution but haven't really found one. Please help.

Hello
Driver from HP web site
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=mp-86352-1 &cc=us&dlc=en&lc=en&os=219&product=4083652&sw_lang=
instruction for configurationn and use
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01846935&tmp_task=setupCate gory&cc=us&dlc=en&lc=en&os=219&product=4083652&softwareitem=mp-86352-1&sw_lang=# N28
HP printer listing for os 10.6 support is not that clear but "HP Officejet Pro L7500 series" in on the list so you may not need to download driver from hp but only from apple
HTH
Pierre

Please help with AcroIEHelper problem

Hello,
I had perfectly running laptop. Now, with no reason every time I turn on my laptop I get a messege that Windows Installer is preparing to install something. Then Installer asks me to insert a disc with Adobe Acrobat 7.0 Pro. When I insert the disc installer tells me that it can not access a file. Exactly:
Adobe Acrobat 7.1.0 Professional
Error 1304: Error writing to file C:\Program Files\Adobe\Acrobat 7.0\ActiveX\AcroIEHelper.dll.
Verify that you have access to that directory.
I checked that directory and did not find such file. Sometimes, this messege appears when I try to open C: or folders on my Desktop but not always. Once it showed up when I tryed to start IE. Ater I uninstalled Adobe Acrobat this messege stopped showing up. But when I reinstalled Adobe Acrobat it started again.
I have tryed almost every anti-malware I could find - McAfee, Spybot, Spyware Doctor, Malwarebyte's Anti-Malware, Superantispyware, AVG 8.5, Dr. Web - all these programms I ran in both normal and safe modes. I even went to BIOS Setup and returned to factory settings. Nothing helped. I went to malware forum and people did not find any malware in my logs.
Then, I installed WinPatrol that seems to be able managing startup programs. After I desabled SC-Acrobat.exe and Adobe Gamma Loader I do not have this annoying Windows Installer for Adobe Acrobat warning any more when Windows starts. But it still shows up often, but not always when I open C: or folders on my Desktop. I have Windows Vista Home.
So could you please help me with this problem? Thank you.

MamaDragonBoy wrote:
It's already set to "mixed" wireless b and g... should I try setting it to all g? Both my laptop and my husband's are "g"
setting it to g certainly wont hurt anything.

Please Help! Calendar problems :(

Hello there ~
I did a system update the other night and when it was complete, I had to reinstall Facebook. Once I did that, I accidently forgot to un-check the FB calendar (which I realize much too late) and it was causing my today theme calendar appts not to show.
I did a search to see why my calendar appts was not showing, which I ran across a thread on another forum - and it said to delete the CICAL, not the CMIME.. I accidently deleted the CMIME. Someone said to go to BIS and have my service book resent, which would restore the CMIME. I did that, then turned around and deleted the CICAL. Still was having the same problem.
Last night I was trying to figure it out - deleted the Facebook app, trying to select the default calendar.. and it still wouldn't work. When I would add an event - it would do it multiple times, yet still not show my other current events (which is what I am needing it to show!!).
Finally, somone suggested some steps to not only go into the calendar options or the service book - but to go into default services, then pick my default calendar (CICAL). The only "option" that is showing is Facebook and I have no other options. I am guessing that I need my original CICAL restored so I can choose it!! Am I correct?? I seriously wish I would of gotten that info a few days ago BEFORE I deleted my original CICAL!!
Unfortunately - I did not backup anything before I did the service update, which oddly enough caused my assigned ringtones to un-assign themselves.. which I think is strange, but whatever. That is an easy fix, but I desperately need my calendar to show up on my today theme!!
Please HELP!! I really need my calendar to show up on my today theme!!
Thank you!!!!

Welcome to the forums
Send service books to the phone by:
1. Logging in to your carrier's BIS site (where you setup your email)
2. Go to Help and click "Send Service Books"
Next, you have to move all your calendar appointments back into your default calendar (whicever one you want it to be). See this KB article, paying attention to Scenario 1 under Resolution: http://www.blackberry.com/btsc/KB19240
Then go back into options>advanced options>default services and set the default calendar to the one you want it to be.
Cheers,
Kijana
Please remember to:
1. Mark Accept as Solution on the appropriate post once your issue has been resolved
2. Give Kudos to helpful posts (click the star next to the post)
Thanks

Please help! WRT54G problems

hi, i have internet access direct from my modem. we had set up a wireless wrt54g sometime ago in 2004 to share the connection with my laptops. we did not enable any security then and recently i was concerned about it and wanted to create my own SSID name (instead of linksys) with password, so i googled 'secure my wireless router' and then accessed 192.168.1.1 upon which it asked for the admin user and pass. typing in 'admin' and various combinations of the password it wasn't working so i assumed someone had changed it remotely. so i hit the reset button on the modem and after which was able to type admin and enter the setup page for the router. then i must have done something cause now my computer cannot access the internet with the router hooked up, but only with the modem. i restored the router to factory default in the set up page for the router, but still the internet is not working through the router. can someone please help me i'm not a computer whiz, but i know i must have toggled some settings and i can't afford to shell 35 bucks just to get help over the phone for some small tweaking! i can get internet access direct from my modem and i know the cables are in correct order. what happened?

Access the setup page of the router by launching an
Browser and type on the address bar, 192.168.1.1 and press enter. When
it prompts for the username and password, leave the username field
empty and provide password as "admin" (Without quotes)
click on ok.
On the main setup page the ""Internet Connection Type"" should be
on ""Obtain IP Automatically - DHCP “. Click on the Save Settings
button.
Now click on the sub tab ""MAC address clone"".
- Click on enable
Click Clone & click save settings
Check WAN Ip on Status page of router ....
If getting Valid Ip .... try going online
If not ... power cycle for 4-5 minutes & then again check the WAN Ip address .....

Please help me setup us the PPP dialup for OS 8.0

I have not the ability to conduct my own research, for all my methods have failed and I am stranded with no internet at my home.
I have the OS 8.0 as my system of operation. My Control Panel doesn't have the PPP option, as many websites have described. I do not know what to do and feel like a helpless baby. Please help, I'm running out of lollertears!
I just need to know where to enter the access number and user name and password that my ISP has provided me.
Thank you and may the Rofl of Bethlehem live inside you all.
The Roflator of Lollerz Mac OS 8.6 or Earlier Roflastic

Michael
I've checked my old PPC 7600.
I didn't find PPP either-but found it in the TCO/IP help under
connecting via modem(I'M using a router in a network,use DHCP server and remote access):
You have to
1)configure the modem
2)Use remote access
In the help menu for TCP/IP the PPP-Server is mentioned!
May be you have got the Internet Connection Kit-I used it to get to internet(only remote acess worked!).
Good luck

I have just started using WD external hard drives, I use it to save my movies and music on. On more than one occasion, when I connect to my MacBook it erases everything on had on there. Can someone please help with this problem?

I have just started using WD external hard drives, I use it to save my movies and music on. On more than one occasion, when I connect it to my MacBook it erases everything I had save on the hard drive. Can someone please help me with this problem? I am super tired of having to put all of my movies and music on the hard drive just to have it erased again. The products I am using are WD 4TB My Book and 2 TB My Passport external hard drives. When it happens, there is always an icon that reads, EFI, along with the My Book icon. Thank you for your assisstance.

dwgar1322 wrote:
I have just started using WD external hard drives, I use it to save my movies and music on. On more than one occasion, when I connect it to my MacBook it erases everything I had save on the hard drive. Can someone please help me with this problem? I am super tired of having to put all of my movies and music on the hard drive just to have it erased again. The products I am using are WD 4TB My Book and 2 TB My Passport external hard drives. When it happens, there is always an icon that reads, EFI, along with the My Book icon. Thank you for your assisstance.
Yes, you have WD software installed REMOVE IT !!
WD has warned its customers about their huge mistake that their software doesnt work on Mavericks and causes data loss.
(also dont use WD drives anymore)
Read all about it here:
https://discussions.apple.com/thread/5475136?start=255&tstart=0
See their website on removing the destructive WD software here:
http://community.wd.com/t5/External-Drives-for-Mac/External-Drives-for-Mac-Exper iencing-Data-Loss-with-Maverick-OS/td-p/613775
Western Digital External Hard Drives Experiencing Data Loss On OS X Mavericks
http://www.cultofmac.com/252826/western-digital-external-hard-drives-experiencin g-data-loss-on-os-x-mavericks/

PLEASE HELP.. PROBLEM WITH RESTORE

okey, well i have this huge problem. i got my ipod 2 weeks ago from the US, i live in poland and not many people know how these things work so i ask that someone here can help me..
a week ago.. the ipod froze my computer, i could do nothing with it. so i had to restart it.the problem was that my ipod was connected to the computer still.. but my comp wouldnt start so i had to disconnect the ipod.(yes the DO NOT DISCONNECT icon was on the ipod.. but wut else could i do?)
so my ipod froze then, and i had the apple icon the whole time on the screen, so i tried everything, i get so frustrated with the ipod that i just want to throw it out the window. i read some things about the problem on the suppoort page, i reset it about a hundred times.. and finally it started working when i got it into disc mode. Yes i got all happy.. I press the restore buttons in itunes.. and this is what happens.. the ( i dont know how to call it) scroll bar? well the green bar that moves to show that its 'restoring' it freezes in the middle of the process, i uninstalled itunes 10 times.. i even tried restoring on 2 other computers, on one of them it does the same thing and on the other theres some other problem.
PLEASE HELP ME!! I DONT know what to do.
ipod 5th gen 30gb Windows XP

____________________16.06V16, Bus Type ATA, Bus Address [0,0]
USBSTOR\DiskApple__iPod___________1.62, Bus Type USB
Universal Serial Bus Controllers:
Otwarty kontroler hosta PCI do USB SiS 7001, Magistrala PCI 0, urządzenie 2, funkcja 2. Device is working properly.
No IEEE 1394 Host Controller found.
The last connected iPod serial number: ****.
The iPod Service Logging Information:
[SERVICE: 0xB20,22:06:21 INFO] Started C:\Program Files\iPod\bin\iPodService.exe (Mon Nov 20 22:06:21 2006)
[SERVICE: 0xB20,22:06:21 INFO] ##### iPodService starting as a service, version: 7.0.2.16
[SERVICE: 0xB2C,22:06:22 INFO] Timed out... Starting device manager!
[SERVICE: 0xB54,22:06:22 INFO] Listener Window created
[SERVICE: 0xB54,22:07:32 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:07:32 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:07:32 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:07:34 INFO] [InterfaceArrival] \\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
[SERVICE: 0xB54,22:07:34 INFO] device \\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
[SERVICE: 0xB54,22:07:34 INFO] device is an iPod
[SERVICE: 0xB54,22:07:34 INFO] type 0x7 drive 0x1 partition 0x0
[SERVICE: 0xB54,22:07:34 INFO] [-1] set waiting to mount = 1
[SERVICE: 0xB54,22:07:34 INFO] [1] Assigning session 0
[SERVICE: 0xB54,22:07:34 INFO] [1] added device interface "\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}" to m_objDeviceNameMap
[SERVICE: 0xB54,22:07:34 INFO] [1] added state machine 1 to m_objDeviceIdMap
[SERVICE: 0xB54,22:07:34 INFO] [1] added device number 1 to m_objDeviceNumberMap
[SERVICE: 0xB54,22:07:34 INFO] [1] added device interface "\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}" to m_vctDeviceInterfaces
[SERVICE: 0xB54,22:07:34 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:07:34 INFO] [1] input #0 from src #0
[SERVICE: 0xB44,22:07:34 INFO] [1] input #0
[SERVICE: 0xB44,22:07:34 INFO] [MACHINE 1 INPUT #0] - (HDW) CheckDevNode
[SERVICE: 0xB44,22:07:34 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB54,22:07:38 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:07:38 INFO] [1] input #1 from src #0
[SERVICE: 0xB48,22:07:38 INFO] [1] input #1
[SERVICE: 0xB48,22:07:38 INFO] [MACHINE 1 INPUT #1] - (HDW) CheckDevNode
[SERVICE: 0xB48,22:07:38 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB54,22:07:39 INFO] [SIMULATED VOLUME ARRIVAL] generating volume mount for \\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
[SERVICE: 0xB54,22:07:39 INFO] [VolumeArrive] mask = 0x7D
[SERVICE: 0xB54,22:07:39 INFO] looking up device # for \\.\G:
[SERVICE: 0xB54,22:07:39 INFO] type 0x7 drive 0x1 partition 0x1
[SERVICE: 0xB54,22:07:39 INFO] iTunes device #1 found with drive letter G, mask 0x40
[SERVICE: 0xB54,22:07:39 INFO] [1] set waiting to mount = 0
[SERVICE: 0xB54,22:07:39 INFO] looking up device # for \\.\F:
[SERVICE: 0xB54,22:07:39 INFO] type 0x2 drive 0x1 partition 0xffffffff
[SERVICE: 0xB54,22:07:39 INFO] looking up device # for \\.\E:
[SERVICE: 0xB54,22:07:39 INFO] type 0x2 drive 0x0 partition 0xffffffff
[SERVICE: 0xB54,22:07:39 INFO] [SIMULATED INTERFACE ARRIVAL] generating connect event for device 0
[SERVICE: 0xB54,22:07:39 INFO] looking up device # for \\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
[SERVICE: 0xB54,22:07:39 INFO] type 0x7 drive 0x1 partition 0x0
[SERVICE: 0xB54,22:07:39 INFO] looking up device # for \\.\D:
[SERVICE: 0xB54,22:07:39 INFO] type 0x7 drive 0x0 partition 0x2
[SERVICE: 0xB54,22:07:39 INFO] [SIMULATED INTERFACE ARRIVAL] generating connect event for device 0
[SERVICE: 0xB54,22:07:39 INFO] looking up device # for \\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
[SERVICE: 0xB54,22:07:39 INFO] type 0x7 drive 0x1 partition 0x0
[SERVICE: 0xB54,22:07:47 INFO] [VolumeArrive] mask = 0x40
[SERVICE: 0xB54,22:07:47 INFO] looking up device # for \\.\G:
[SERVICE: 0xB54,22:07:47 INFO] type 0x7 drive 0x1 partition 0x1
[SERVICE: 0xB54,22:07:47 INFO] iTunes device #1 found with drive letter G, mask 0x40
[SERVICE: 0xB54,22:07:47 INFO] [1] set waiting to mount = 0
[SERVICE: 0xB54,22:07:47 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:07:47 INFO] [1] input #2 from src #0
[SERVICE: 0xB4C,22:07:47 INFO] [1] input #2
[SERVICE: 0xB4C,22:07:47 INFO] [MACHINE 1 INPUT #2] - (HDW) CheckDevNode
[SERVICE: 0xB4C,22:07:47 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB50,22:07:51 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB50,22:07:51 INFO] [First Connect] Creating connect event for device 1
[SERVICE: 0xB50,22:07:51 INFO] [1] set waiting to mount = 1
[SERVICE: 0xB50,22:07:51 INFO] [1] input #3 from src #0
[SERVICE: 0xB44,22:07:51 INFO] [1] input #3
[SERVICE: 0xB44,22:07:51 INFO] [MACHINE 1 INPUT #3] - (HDW) Interface Arrival
[SERVICE: 0xB44,22:07:51 INFO] [1] progress state is 2, Waiting to mount = 1
[SERVICE: 0xB44,22:07:51 INFO] [1] progress is now 2
[SERVICE: 0xB44,22:07:51 INFO] [1] progress is now 2
[SERVICE: 0xB44,22:07:51 INFO] [MACHINE 1 TRANSITION] - {Unknown} ==> {Connected}
[SERVICE: 0xB44,22:07:51 INFO] [MACHINE 1 ACTIONS] - {Connected}
[SERVICE: 0xB44,22:07:51 INFO] [1] SCSI Inquiry attempt #0
[SERVICE: 0xB50,22:07:52 INFO] [First Connect] Creating mount event for device 1
[SERVICE: 0xB50,22:07:52 INFO] [VolumeArrive] mask = 0x7D
[SERVICE: 0xB50,22:07:52 INFO] looking up device # for \\.\G:
[SERVICE: 0xB50,22:07:52 INFO] type 0x7 drive 0x1 partition 0x1
[SERVICE: 0xB50,22:07:52 INFO] iTunes device #1 found with drive letter G, mask 0x40
[SERVICE: 0xB50,22:07:52 INFO] [1] set waiting to mount = 0
[SERVICE: 0xB50,22:07:52 INFO] [1] input #4 from src #0
[SERVICE: 0xB50,22:07:52 INFO] looking up device # for \\.\F:
[SERVICE: 0xB50,22:07:52 INFO] type 0x2 drive 0x1 partition 0xffffffff
[SERVICE: 0xB50,22:07:52 INFO] looking up device # for \\.\E:
[SERVICE: 0xB50,22:07:52 INFO] type 0x2 drive 0x0 partition 0xffffffff
[SERVICE: 0xB50,22:07:52 INFO] [SIMULATED INTERFACE ARRIVAL] generating connect event for device 0
[SERVICE: 0xB50,22:07:52 INFO] looking up device # for \\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
[SERVICE: 0xB50,22:07:52 INFO] type 0x7 drive 0x1 partition 0x0
[SERVICE: 0xB50,22:07:52 INFO] looking up device # for \\.\D:
[SERVICE: 0xB50,22:07:52 INFO] type 0x7 drive 0x0 partition 0x2
[SERVICE: 0xB50,22:07:52 INFO] [SIMULATED INTERFACE ARRIVAL] generating connect event for device 0
[SERVICE: 0xB50,22:07:52 INFO] looking up device # for \\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
[SERVICE: 0xB50,22:07:52 INFO] type 0x7 drive 0x1 partition 0x0
[SERVICE: 0xB44,22:07:53 INFO] VendorId: Apple
[SERVICE: 0xB44,22:07:53 INFO] ProductId: iPod
[SERVICE: 0xB44,22:07:53 INFO] revision: 1.62
[SERVICE: 0xB44,22:07:53 INFO] vendor bytes:
[SERVICE: 0xB44,22:07:53 INFO] 02 01 00 00 00 00 00 00 00 0B 00 11 91 00 00 00 00 00 00 00
[SERVICE: 0xB44,22:07:53 INFO] [1] firmware version: 1.62 (0x13E)
[SERVICE: 0xB44,22:07:53 INFO] [1] Power State: Powered
[SERVICE: 0xB44,22:07:53 INFO] [1] Checkpoint attempt #0
[SERVICE: 0xB44,22:08:01 ERROR] Did not find first letter of stage
[SERVICE: 0xB44,22:08:01 INFO] got HotPlugState 0
[SERVICE: 0xB44,22:08:01 INFO] [1] serial number 000A270015BEEE43
[SERVICE: 0xB44,22:08:01 INFO] [1] *** CONNECTED - Sending event out, device session 0.
[SERVICE: 0xB44,22:08:01 INFO] [1] input #4
[SERVICE: 0xB44,22:08:01 INFO] [MACHINE 1 INPUT #4] - (HDW) Volume Mount
[SERVICE: 0xB44,22:08:01 INFO] [MACHINE 1 TRANSITION] - {Connected} ==> {Mounted}
[SERVICE: 0xB44,22:08:01 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB44,22:08:01 INFO] [MACHINE 1 ACTIONS] - {Mounted}
[SERVICE: 0xB44,22:08:01 INFO] [1] progress state is 2, Waiting to mount = 0
[SERVICE: 0xB44,22:08:01 INFO] [1] progress state is 2, Waiting to mount = 0
[SERVICE: 0xB44,22:08:13 ERROR] Did not find first letter of stage
[SERVICE: 0xB44,22:08:13 INFO] got HotPlugState 0
[SERVICE: 0xB44,22:08:17 INFO] [1] GetVolumeInformation() failed with error 1005
[SERVICE: 0xB44,22:08:17 INFO] [1] ===== iPod with Video =====
[SERVICE: 0xB44,22:08:17 INFO] [1] progress state is 2, Waiting to mount = 0
[SERVICE: 0xB44,22:08:17 INFO] [1] iPod needs formatting...
[SERVICE: 0xB44,22:08:17 INFO] 22:8:17, year 2006, day of yr. 323, GMT offset 4 isDST 0
[SERVICE: 0xB44,22:08:17 INFO] [1] Perform launch updater check.
[SERVICE: 0xB44,22:08:17 INFO] [1] iTunes located at 'D:\iTunes.exe'
[SERVICE: 0xB44,22:08:17 INFO] [1] progress is now 0
[SERVICE: 0xB44,22:08:17 INFO] [1] *** MOUNT FAILED - Non-FAT32 device, device session 0
[SERVICE: 0xB34,22:08:57 INFO] <0x4> Got Serial #
[SERVICE: 0xBD0,22:09:01 INFO] [1] GetVolumeInformation() failed with error 1005
[SERVICE: 0xBD0,22:09:01 INFO] <0x4> GetFormatType() returned unknown format 4
[SERVICE: 0xBD0,22:09:01 INFO] [1] Progress state is 0, Waiting to disconnect = 0
[SERVICE: 0xD04,22:09:01 INFO] Mounted
[SERVICE: 0xD04,22:09:01 INFO] [1] already mounted!
[SERVICE: 0xD04,22:09:01 INFO] [1] progress state is 0, Waiting to mount = 0
[SERVICE: 0xB34,22:09:03 ERROR] ERROR, mount lock count is 0 but device is not mounted
[SERVICE: 0xBD0,22:09:07 INFO] [1] GetVolumeInformation() failed with error 1005
[SERVICE: 0xBD0,22:09:07 INFO] <0x4> GetFormatType() returned unknown format 4
[SERVICE: 0xBD0,22:09:16 INFO] <0x1> Got Serial #
[SERVICE: 0xB34,22:09:16 INFO] <0x1> Got Serial #
[SERVICE: 0xB34,22:09:20 INFO] [1] GetVolumeInformation() failed with error 1005
[SERVICE: 0xB34,22:09:20 INFO] <0x1> GetFormatType() returned unknown format 4
[SERVICE: 0xBD0,22:09:22 INFO] <0x1> Got Serial #
[SERVICE: 0xBD0,22:09:22 INFO] API is now LOCKED!!!
[SERVICE: 0xB54,22:11:15 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:11:15 INFO] [1] input #5 from src #0
[SERVICE: 0xB48,22:11:15 INFO] [1] input #5
[SERVICE: 0xB48,22:11:15 INFO] [MACHINE 1 INPUT #5] - (HDW) CheckDevNode
[SERVICE: 0xB48,22:11:15 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB54,22:12:22 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:12:22 INFO] [1] input #6 from src #0
[SERVICE: 0xB4C,22:12:22 INFO] [1] input #6
[SERVICE: 0xB54,22:12:22 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:12:22 INFO] [1] input #7 from src #0
[SERVICE: 0xB44,22:12:22 INFO] [1] input #7
[SERVICE: 0xB4C,22:12:22 INFO] [MACHINE 1 INPUT #6] - (HDW) CheckDevNode
[SERVICE: 0xB4C,22:12:22 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB44,22:12:22 INFO] [MACHINE 1 INPUT #7] - (HDW) CheckDevNode
[SERVICE: 0xB44,22:12:22 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB54,22:18:13 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:18:13 INFO] [1] input #8 from src #0
[SERVICE: 0xB48,22:18:13 INFO] [1] input #8
[SERVICE: 0xB48,22:18:13 INFO] [MACHINE 1 INPUT #8] - (HDW) CheckDevNode
[SERVICE: 0xB48,22:18:14 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB54,22:21:48 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:21:48 INFO] [1] input #9 from src #0
[SERVICE: 0xB4C,22:21:48 INFO] [1] input #9
[SERVICE: 0xB54,22:21:48 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:21:48 INFO] [1] input #10 from src #0
[SERVICE: 0xB44,22:21:48 INFO] [1] input #10
[SERVICE: 0xB4C,22:21:48 INFO] [MACHINE 1 INPUT #9] - (HDW) CheckDevNode
[SERVICE: 0xB4C,22:21:48 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB44,22:21:48 INFO] [MACHINE 1 INPUT #10] - (HDW) CheckDevNode
[SERVICE: 0xB44,22:21:48 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB54,22:44:23 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:44:23 INFO] [1] input #11 from src #0
[SERVICE: 0xB48,22:44:23 INFO] [1] input #11
[SERVICE: 0xB48,22:44:24 INFO] [MACHINE 1 INPUT #11] - (HDW) CheckDevNode
[SERVICE: 0xB48,22:44:24 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB54,22:52:27 INFO] [VolumeRemoved] existing mask 0x40, arrive mask 0x20
[SERVICE: 0xB54,22:52:47 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:52:47 INFO] [1] input #12 from src #0
[SERVICE: 0xB4C,22:52:47 INFO] [1] input #12
[SERVICE: 0xB54,22:52:47 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:52:47 INFO] [1] input #13 from src #0
[SERVICE: 0xB44,22:52:47 INFO] [1] input #13
[SERVICE: 0xB4C,22:52:47 INFO] [MACHINE 1 INPUT #12] - (HDW) CheckDevNode
[SERVICE: 0xB4C,22:52:48 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB44,22:52:48 INFO] [MACHINE 1 INPUT #13] - (HDW) CheckDevNode
[SERVICE: 0xB44,22:52:48 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB54,22:52:49 INFO] [VolumeArrive] mask = 0x20
[SERVICE: 0xB54,22:52:49 INFO] looking up device # for \\.\F:
[SERVICE: 0xB54,22:52:49 INFO] type 0x2 drive 0x1 partition 0xffffffff
Windows XP
well i clicked help.. and that didnt do anything either.. ;/

Very frastrated. Please HELP! SX712 problem copying music from latptop to IC recorder

It worked before. I haven't used it for a while. Now, I wasted hours to try to solve this problem to no avail.
When I connected my SX712 IC Recorder to my laptop, I could see 3 folders: MUSIC, PODCAST and VOICE and one file: capability_01.
I copied a bunch of MP4 files to the MUSIC folder and then disconnected the IC Recorder from the laptop.
On the IC Recorder, I pressed the "folder" button. Only MUSIC and BOOKS were shown next to the Conversation icon. The Conversation icon was the only icon showing on the left panel. There was no MUSIC or PODCAST icons or any of the files that I copied over which were visible to me when the IC Recorder was connected to the laptop.
What did I do wrong?
Please HELP!
Many Thanks in advance...Mimi

Hi Mimi! The ICD-SX712 Digital Voice Recorder only supports MP3, WMA, AAC-LC and PCM files. MP4 files are not supported.
If my post answers your question, please mark it as "Accept as Solution"
http://bit.ly/Win-4K

Please Help! Two problems with my iMac at once a week b/4 finals!!!!

First I'd just like to mention that I have no idea which OS X I have so...yeah, sorry. I was depending on this computer to work for my class finals. Anyway, on with the problems.
My school is getting all new computers next year, so they are selling all of their iMacs for ten dollars each. Like an idiot, I bought one. And...so did my brother. But anyway, I got it home and started it up and all that came up was the traditional BIIINNNNGGGG, a white screen(for a second), then a gray one. This little icon comes up in the middle that you can't click on(the cursor doesn't come up)but it's purple and has a little cartoon face on it. This icon only comes up if you are not pressing any keys or click/moving the mouse.
So I went back to school the next day and asked what was up, and they said that they completely wiped the computer and that I would have to buy new OS X install software. Okay...so I went to my computer teacher and he had a few sets of OS X install software.
I brought it home and turned on my computer. I put in the disk that said OS X Install and it went in. The computer whirred for a bit, then spit the disk back out. So I decided to try a different disk because I thought that maybe the computer already had the contents of that disk on it. I put in the Applications disk, and now it refuses to come out. I have tried plugging the keyboard into different ports(there are two, with two others on the keyboard itself for the mouse) and everything. I looked inside through the little slot(discs go right into the computer-no hard drive or disk tray that slides out) on the front and the disc is spinning but nothing is happening.
Please help me with both my wiped computer problem and my stuck disc problem. I have tried to give as much detail to help anyone who can help me. Please, WHAT CAN I DO?!
iMac Mac OS X (10.0.x) I have an OS X. No idea which one...
iMac Mac OS X (10.0.x) I have an OS X. No idea which one...
iMac Mac OS X (10.0.x) I have an OS X. No idea which one...

The full retail install disks are available here and at any Apple Store and many computer retailers. Also, check the system requirements. Be sure your Mac has firewire and enough ram to run Tiger. At this point you might be able to find the disks at a slightly discounted price because of the coming release of 10.5 Leopard. But be sure it is the black disk, boxed version if possible.
EDIT: And the install disc for Tiger is a DVD, so be sure your iMac has DVD.
This may help to narrow down the model iMac you have.
-mj
[email protected]
Message was edited by: macjack

Please help: Internet Setup Problems.

Similar Messages

Maybe you are looking for