Please, help me to set up wireless Internet connection. M...

         Please, help me to set up wireless Internet connection. My router is WRT54GS. I able to get online when computer is wired direct to VPN internet cable.
First, I can’t open password request screen on http://192.168.1.1. 
Second, when "Setup wizard" runs step #6 (“Check the router’s status”), the program asks for the password. Default password “admin” is rejected by the program and I can’t install Linksys software. Just in case I already pressed reset switch on the back of the router but to no avail. 
Third, I don’t find out my Ethernet Adapter Wireless Network Connection and correct router’s IP address using ipconfig/all command after connecting WRT54GS with my computer. Ethernet adapter: DHCP disabled, subnet mask 255.255.255.0, IP address 10.32.132.193, default gate 10.32.132.1.
Tell me please: what’s the matter?

Pensive wrote:
         Please, help me to set up wireless Internet connection. My router is WRT54GS. I able to get online when computer is wired direct to VPN internet cable.
First, I can’t open password request screen on http://192.168.1.1. 
Second, when "Setup wizard" runs step #6 (“Check the router’s status”), the program asks for the password. Default password “admin” is rejected by the program and I can’t install Linksys software. Just in case I already pressed reset switch on the back of the router but to no avail. 
Third, I don’t find out my Ethernet Adapter Wireless Network Connection and correct router’s IP address using ipconfig/all command after connecting WRT54GS with my computer. Ethernet adapter: DHCP disabled, subnet mask 255.255.255.0, IP address 10.32.132.193, default gate 10.32.132.1.
Tell me please: what’s the matter?
hi pensive ,
 Seems interesting , first do this -  push the reset button on the back of router .
push it till 30 seconds , unplug the power cable and plug in the power cable back in After completion of 30 seconds.
then try to log into , 192.168.1.1 again . with the password "admin".
see if it reply?
Else -
strt>cmd>ipconfig /all - post the result ?
pe@c3
Message Edited by meteor on 01-09-2008 05:58 AM
~~~Nobudy's Perfect , i try To Be So ! Each n every moment of maH LYF , AND I THINK dat wats make Me "Different" From others....~~~

Similar Messages

  • Can anyone help me set up wireless internet connection?

    I have 2 computers a windows and the Mac and for the first time I can avail of broadband in my area ,I currently use an ISDN line to connect. So I will recieve a wireless modem which will be connected to the windows computer by a wireless usb adaptor and my question is how do I connect the mac wirelessly to the modem which will be in a different room in the house.
    I would be very grateful for advice .
    Thanks in advance

    It means you don't have a wireless (apple calls it airport) card installed on your computer. So similar to your pc, which uses the USB adapter, there are alternatives for your iMac. You could install an airport card although this might not be the most cost effective way. Your best bet would be to contact a specialist to ensure that your computer is compatible and ready for this product though.
    http://store.apple.com/us/product/M8881LL/A?fnode=MTY1NDA0Mg&mco=MjE0NDc1Mw
    I'd try something like the link below. I have no experience with any product like this for an Apple, so I can't recommend anything or comment on their functionality. I'm sure there are more available as well.
    http://www.macmall.com/macmall/shop/detail.asp?Redir=1&description=Addlogix%2DUS B2%2E0+Wireless+%28IEEE+802%2E11b%2Fg%29+Adapter%2DWirelessNetworking&dpno=7037199

  • Setting up a Wireless Internet Connection on Solaris 10

    I am new to the whole Solaris/unix world and I was just wondering how to set up a wireless internet connection with a solaris 10 machine. I have a linksys router hooked up to a cable modem and a linksys receiver hooked up via USB on the solaris machine. I would greatly appreciate any help anyone can give me.

    Was the router supplied by the ISP or was it bought separately? Are you able to get online when connecting the Mac directly to the router via an ethernet cable? Either way it's best to check the router settings to ensure they are correct.
    I’ve not come across the Zoom routers. Setup should be straight forward though, having gone to their website and downloaded the manual. Do the following:
    1. Plug one end of the RJ-11 cable (included in the box) to the router, the other end to your phone line via the micro-filter.
    2. Plug one end of the ethernet cable (again included in the box) to the appropriate port in the router, the other end to your Mac.
    3. Plug in the power cord and switch on
    4. Fire up your web browser on your Mac (Safari, Camino, Firefox etc)
    5. In the address bar of the web browser type 10.0.0.2 and hit the Return button
    6. A Network Password box will appear. This is to gain access to the router itself. The defaults are, Username = admin, Password = zoomadsl
    7. You’ll now enter the Basic Setup screen. It’s here where you enter the username and password supplied by your ISP. This is NOT your email username/password but your Internet access ones. If you are not sure or don't have them, call your ISP.
    8. Click Save Changes and then click Write Settings to Flash and Reboot. Once the router has reset itself and the Link light comes on and remains steady, you’re online.
    That’s it. Job done
    If you still cannot get access it may be worth resetting the router (there should be a small button in the back which requires the use of a pen or pencil to press) re-entering your ISP information as described above and trying again.
    Let me know how you get on.
    Kryten

  • Best way to set up wireless Internet with my situation?

    Hello All,
    I am looking for a little help. I have a PBG4 and a new imac. I would like them both to have a wireless internet connection. Reason being is that there is no phone line/cable Internet connection in the room the imac is in. The cable internet comes into the living room where i often use my PBG4.
    Is there a way to set up my internet connection, so that the internet cable enters a router and both computers can access the wireless connection with no cabled attached. A USB printer port would be nice also. On paper it looks like the Airport Express can do this. Is this correct? Or am I missing something. I like the fact that is has the music/audio jack is well. While shopping for routers it looks like a lot of them need a home computer to be hard wired into them.
    What would my best option be?
    Thank you for your time in advance. Sorry about my lack of tech knowledge.
    TG

    Tim Gair wrote:
    Is there a way to set up my internet connection, so that the internet cable enters a router and both computers can access the wireless connection with no cabled attached. A USB printer port would be nice also. On paper it looks like the Airport Express can do this. Is this correct?
    Yes, an Airport Express would meet your needs.
    Or am I missing something.
    No you're not.
    While shopping for routers it looks like a lot of them need a home computer to be hard wired into them.
    They can have a computer hard wired in, but for all routers it is not essential.
    iFelix

  • Please help my ipod disconnected from the Internet and wont reconnect and i did the right password

    please help my ipod disconnected from the Internet and wont reconnect and i did the right password

    - Do other devices still connect to the network?
    - Does the iPod connect to other networks?
    - Reset the iPod. Nothing will be lost
    Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Power off and then back on the router.
    - Reset networks settings: Settings>General>Reset>Reset Network Settings
    - iOS: Troubleshooting Wi-Fi networks and connections
    - iOS: Recommended settings for Wi-Fi routers and access points

  • Time Capsule Degrades Wireless Internet Connection: Help?

    Time Capsule Degrades Wireless Internet Connection: I am in FL using Brighthouse Cable as my internet provider (15MG down). The internet connection speed is slower than a dial up connection when wirelessly connected to my network to my Time Capsule. When I remove the Time Capsule and replace it with Brighthouses Netgear router the internet speed are normal (fast). Additionally, the internet speed is OK when I first hit a website, but the speed degrades rapidly as I access additional web pages. I no longer use my Time Capsule and therefore are not getting my back-up protection. (NOTE: I tried Verizon Fios and had the same problem.) Can anyone help?

    Bought the time capsule in Oct 2013.  I have a Sagemcom 2864 modem from Bell but used through Teksavvy.  The 5 ghz has been flaky until I upgraded to Yosemite 10.10.1 I think.  I had a closer look at it and it appears that the wifi is ok.  I was thrown off by the wifi symbol being all animated in the menu bar.  I was able to ping the time capsule via wifi.  All the status lights on the modem looked ok.  Next time it happens, I'll see if I can get some more details.  Do you know if there's anyway to get some logs from the airport utility?

  • Wireless internet connection is poor, wireless internet connection is poor

    Hi..
    I just purchase an iMac desktop and dont know much on how to use them. A couple of questions: when i set up the comp, it suggested that i could transfer my data from another computer to this. I clicked yes, followed the promts. It loaded for 4 hours then said it was succsefull. Both on my imac and my laptop. However, i cant find any of my information, photos, documents etc??
    Second question is: My wireless internet connection seems to be quite poor? Its slower than what is was on my laptop. I went to apple store, went to poor wirelss conection they wanted my serial number so i did that and it just had the loading symbol for aagggeess and nothing happened? ive tried to call Mac support, it said thats is currently closed but didnt say when they open.
    Any help will be appreciated!
    Thanks Cait

    Hello CAit & welcome!
    It loaded for 4 hours then said it was succsefull. Both on my imac and my laptop. However, i cant find any of my information, photos, documents etc??
    Look in the Users folder far another/imported ID to log into.
    Let's seehow the Wifi is under the other account.

  • Slow wireless internet connection using airport extreme

    My wireless internet connection works but is very slow (<80kbs). The problem seems to be with the airport extreme (brand new, purchased in May 07) because my connection is very fast (>6mbs) when i connect by wire to the airport extreme base station. Signal strength is strong, so i can't figure out the problem. Any ideas?
    imac Mac OS X (10.4)

    BK37, I hope you've solved your problem by now. But if not, and for the benefit of others reading this post, let me share what I (finally) discovered when I had virtually the same problem, i.e. 8mbps wired speed, <50kbps wireless speed.
    I tried literally <span style="font-style:italic;">every suggestion I could find in the Airport discussions. First, I can assure you that changing the channel can give you incremental speed improvements in some instances, but for radical drops like yours, it's not the answer. Nor is turning off ipv6, or changing to WEP, or turning off Remote Access, or moving the AEBS, or or or or or....
    With such a radical drop in speed, it's most likely you have a hardware-related blockage somewhere. In my case it was my wiring configuration. My setup was France Telecom Livebox (ADSL modem / ethernet & 802.11g router) --> Ethernet cable --> Linksys RTP 3100 IP phone adapter / router --> Ethernet cable --> AEBS --> 3 Airport Express set up to extend network and run AirTunes. After eliminating every other possible problem, I narrowed it down to the Linksys router, which for reasons I have yet to figure out was trapping the speed to the AEBS. I ethernet cabled both the Linksys router and the AEBS directly to the Livebox and presto! Back to blazing speed.
    Hopefully this info will be helpful to you or some poor soul in the same situation, as I would have loved to have had it myself before I pulled every hair out of my head!
    iMac 21" Intel   Mac OS X (10.4.9)  

  • Laserjet 1022 w error to wireless internet connection

    I installed my wireless laserjet 1102 w.
    It is running, I am able to connect by wireless to the printer and I am able to print but when
    I connected to the page of configuration and try to activate the eprint option I receive the message "error to internet connection".
    So I am not able to receive the printer code to activate eprint.
    My wireless internet connection is correcly running with other wireless devices

    Hello guidogio55,
    Please take a look at this document, and let me know if the troubleshooting steps help to resolve your issue.
    Good luck!
    ↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

  • IMAC Wireless Internet Connection Problems All Of A Sudden

    My Imac is well over a year and a bit old and has been able to connect to my wireless internet connection absolutely fine until the past week and a half. At first the connection wouldn't work and when I would turn my airport on and off and reset the router, it would eventually work, now that is not working at all. My airport status is either showing 'airport is turned on but is not connected to a network' or 'airport has a self-assigned ip address and may not be able to connect to the internet'
    I have formatted my imac twice and still no avail and the last format I tried to join wirelessly straight from boot but it wouldn't join saying 'there is a problem with the wireless connection and you're not connected to the internet.' the annoying thing is I can see the network sitting there and can't join it, my network is also unsecure so no need to input a password. All my home PC's and my Iphone and Blackberry find the network easily enough, although recently the Iphone has began showing only 1 bar of wifi connection.
    I am at my wits end as I am unable to connect at all now, I am all out of ideas and have been bashing my head off a wall for the past day without any connection at all.
    My router is a buffalo AirStation wireless G high power model, my IMAC is an intel core 2 duo 20", if you need anymore information of my hardware I will gladly provide it. I'm running MAC OSX Leopard 10.5, out the box as I've been unable to run any software updates as I can't connect to the internet.
    Please, if anyone can shed any light at all on this issue I would definately try anything.
    Thanks in advance and regards.
    Message was edited by: proxykillah

    Anytime you see a self-assigned IP address in your network prefs you know it surely is a problem
    with your router configuration. Power down all equip ... make sure modem is off for at least 5 minutes
    restart modem, restart iMac ... check your network pref on iMac and make sure it's not 169.x.x.x
    If so you will need to recapture the settings from your ISP's modem to the Buffalo.
    Always use a secure wireless connection (WEP, WPA, WPA2) or else the whole neighborhood will suck down your bandwidth the slow down what your paying for. I use Time Capsules or AEBS (Airport Extreme Base Stations) that allow you to stealth mode and lower signal output and make the device
    as a "closed network" ... meaning no one else can see and tap into your WIFI home network!
    802.11N is better than G. and especially when you can use dual bands 2.4 / 5GHz to stop various home interferences. The backup of Time Machine only makes life much easier also! Xtech

  • Asking to set up an internet connection when we press approve button

    Hi friends can u expalin me
    when i press approve button in the notification it is asking for set up an internet connection wizard
    i am attaching the screen shot can u have a look please
    thanks
    sesh

    Probably you are working on the server itself (windows) i.e the same machine on which you have installed Oracle Applications and the time you press the notification it is trying to send a email for which the wizard comes up.
    Anyways i did not see any screen shot.
    Sam
    http://appstech-sam.blogspot.com

  • Extending a wireless internet connection to another part of a building

    We have a wrt54g wireless router connected to a quest dsl modem. we now want a wireless internet connection in another part of the building which is out of range of the wrt54g. the two areas are about 200 ft apart and i can run a cat5 cable to new area. Can i install a second wrt54g in the new area and how exactly do i configure it for security and connectivity. 
    Thanks
    Gary

    Yes, you can do what you described.   You can run cat5 cable if you want, but it will need to be very high quality (i.e. professional grade) cat5 cable installation to make a 200 foot connection.   If you are doing this yourself, I would suggest you start with good quality cat5e cable for such a long run.   And make sure the cat5e connection works before you string the cable.
    You will also need to convert the second router to a WAP (wireless access point), by making a few simple setting changes.
    For instructions on setting up your system, see my post at:
    http://forums.linksys.com/linksys/board/message?board.id=Wireless_Routers&message.id=108928
    Message Edited by toomanydonuts on 05-01-2009 04:23 AM

  • For those who constantly lose their wireless internet connection using WRT54G

    Ok I was constantly losing my wireless internet connection on my LAN network when using my laptop, I tried everything to no avail,until today. Heres what I did to solve my problem
    1. Upgrade your firmware for the WRT54G to ver.6
    2. Reset your wireless router
    3. Unplug all cables and wires from your Pc and router
    4. Connect your Pc directly to your cable modem and obtain an internet connection
    5. Now transfer files you want to keep from your laptop onto a usb flash drive or burn them to a disk
    6. Reformat your laptop so that it goes back to all factory settings just like when you bought it
    7. When completely done reformatting run software that came with the WRT54G on your desktop pc and follow all instructions,when prompted to type password type the password you last used
    8. Go to your laptop and it should pickup a LAN,click connect, it will ask for the encryption key so type it in(whatever you typed when re-installing your wireless router)
    Congratulations you are now back up and running,install files saved earlier back on your laptop and enjoy.This is what I did and it solved my problem as a matter of fact i typed this from my laptop and has not dropped my wireless internet connection yet.
    NOTE SAVE ANY AND ALL FILES YOU WANT TO KEEP AS REFORMATTING WILL CAUSE YOU TO LOSE DATA!
    IAM IN NO WAY RESPONSIBLE FOR ANY ERRORS OR PROBLEMS THIS PROCEDURE COULD CAUSE IF DONE INCORRECTLY!

    If you bought a version 5 or 6 return it to where you bought and apply the money towards a WRT54GL v1.x  You'll be much happier.  You could spend time online rather than pulling your hair out trying to figure out whats wrong.  I setup 6 Linux based WRT54G's with no issues before I was given the task of setting up a version 6.  Worked for about an hour.  Told the guy to return it for a GL.  Long story short, set it up in a matter of minutes and he was online.  That was 3 weeks ago and he is very happy.

  • ITunes 8.1 works great but killed wireless internet connection

    I installed version 8.1 on both my laptop( PowerBook g4/ OS 10.4.11) and desktop (imac intel / OS 10.5) and after restarting the computer, the wireless internet connection stopped working on both.
    I would open Safari and it would be a blank page and and the circle would keep spinning.
    So I tried my laptop at a different wireless hotspot and had the same result.
    I then tried repairing permissions and I got a list of problems with iTunes/Network Utilities, they repaired and now when I open Safari I get the message that it can not connect to the internet.
    I do get an internet connection using ethernet on both.
    Any ideas on how to fix this problem?

    Did you by any chance also update the firmware on your Apple Airport Extreme (if that's what you have)?
    I thought 8.1 killed my connection to my Apple TV, but it was the faulty firmware (see reports elsewhere in these forums).
    Now that I have rolled back from 7.4.1 on my Airport I plan to try iTunes again (with white knuckles).
    -dan

  • Firefox won't detect coffee shop wireless internet connection, but explorer will, automatically

    Firefox won't detect coffee shop wireless internet connection, but explorer will, automatically

    that's fine, thank you
    but if it doesn't connect
    what's the alternative procedure
    what do I do

Maybe you are looking for