Please help me with scsi HD Problem

Please help me with scsi HD Problem.
Hi for the life of me I cant resolve this.
I have a ms-6378 ver.3 board with 1.1g AMD
i could not install windows 2000 on a Seagate 73Gig 68 pin SCSI Drive ultra wid. after giveing up i added a IDE HD and install win2k SP2 and added the SCSI card all still worked ok
but as soon as i added the hardrive it locks up and it will
not compleat the load of win2k and tried a smoler drive 18Gig 68 pin SCSI Drive. but it will not load windows 2000. i am stumpt. ;(

It sounds like an IRQ conflict. Make sure you diable the primary and secondary channels for the IDE ports to free up the IRQ resources for the SCSI drives. If you are using a separate SCSI controller, make sure it is in the proper PCI slot and does not share IRQ's with other cards.

Similar Messages

Please help me with an AOL problem

I have been on the phone with Apple and AOL with this problem and both say to call the other one. I am about to run out of time to return my iPhone if this doesn't work.
I have two AOL accounts. The first one [email protected] is listed in iTunes and is my default account. In settings this account has all the information regarding incoming and outcoming servers. I have changed the outgoing port number for 567, 25, 234 (?), and cwmx.com with the SSL on and off. I have tried with the wifi on and off. I am just not getting any emails, can't send any, although they go into outbox and just sit. This is my personal consulting business account and I cannot communicate with my clients.
The second account - in settings doesn't have any incoming or outgoing server information listed and I can get and send emails. When it checks for emails, it says there are three emails waiting to be send (from the mxxx account). Go figure.
Please, please help me address this problem. Thank you in advance

Whoa, slow down…
The settings for SMTP for AOL or AIM Mail are:
• port 587
• SSL enabled
• authentication via password
That's it. What's up with 567, 25, and 234? Or, with cwmx.com and SSL on or off? Only the settings listed above will work correctly.
If the alternate account does not have any values set for SMTP, where is it getting the data and how is it operating properly?

I'm getting the run-around. Can someone please help me with a rebate problem?

I purchased a Samsung W/D from Best Buy with the free vacuum offer. It was delivered and I submitted my rebate request. The submission page said to wait 6 to 8 weeks for processing. I waited 8 weeks and then became concerned. When I called the rebate center they said they had no record of my submission. Obviously, the online process failed. I understand technology doesn't always work, but the operator and manager told me I would now not be able to get my rebate and only offered a mailing address to complain. I am EXTREMELY frustrated. First, because the only reason I purchased these units was for the rebate and now I cannot return them to Best Buy because of the time elapsed. Second, if I was aware that there was a problem with the submission I would have been able to fix the situation. The website said all was OK, and all the information said to wait 6-8 weeks. Why would I have checked in before that time? Now I'm told I'm too late to fix it??? All I want is the vacuum cleaner I was promised when I purchased the W/D. Can someone please help me?

Hello ChadMelton,
I have a hard time passing up offers for free products, so I understand how such an offer could influence your decision to buy. I'm wholly disappointed to read, though, that your rebate experience didn't go smoothly and that the manufacturer seems to have been less than cooperative. I would be frustrated too under such circumstances!
I was unable to locate your purchase using the information you provided when you signed up for Best Buy Unboxed. I would like to look into this situation on your behalf, but will need more information to begin. If you will please send me a private message that includes your full name, telephone number, order number and/or the Customer Service PIN from your purchase receipt, I'll get started.
I'm very grateful that you wrote to us with your concerns.
Sincerely,

Please help me with my apple problems!

I have a iphone 4. My husband has a iphone 3gs and a ipad2. When we set his ipad up it linked my phone to both of his devices.All of my contacts have went to him and if he deletes one it deletes off of my phone. Everything of ours even phone numbers have linked together and its really aggravating. Someone please help me if you know the solution, please!!!!!!

This is happening because you're syncing all devices with iCloud and you're using the same Apple ID for iCloud on all the devices. You need either use a different iCloud account on your phone to keep your contacts separate, or stop syncing your contacts with iCloud (not recommended since syncing contacts prevents loss).
On your phone:
Settings > iCloud > (scroll down) > Delete Accout > Keep contacts on phone > set up new iCloud account with different Apple ID
or to stop syncing:
Settings > iCloud > Contacts > OFF

Please help me with this strange problem again!

Hi gurus,
I can't, for the life of me, figure out why this does not work in a procedure but works in an anonimous block.
The XML is like this (part of it),
<CaseNotification messageProducedDateTime="2005-07-20T13:58:11-05:00" xmlns="http://www.courts.state.mn.us/CourtXML/2.0.0">
               <NotificationAdminHeader caseNumberKey="87CR0569" xmlns="http://www.courts.state.mn.us/CourtXML/2.0.0">
                    <CaseCountyIdentifier>87</CaseCountyIdentifier>
                    <CaseLocationText>Yellow Medicine County</CaseLocationText>
                    <BaseCaseTypeText>Adult</BaseCaseTypeText>
                    <CaseCategoryText>Criminal</CaseCategoryText>
                    <PartyIdentifier partyKey="854">
                         <PartyCaseAssociationText>Jurisdiction</PartyCaseAssociationText>
                    </PartyIdentifier>
                    <PartyIdentifier partyKey="123637">
                         <PartyCaseAssociationText>Defendant</PartyCaseAssociationText>
                    </PartyIdentifier>
               </NotificationAdminHeader>
               <InterimConditionsNotification>
                    <TriggeredDateTime>2005-07-20T13:57:53-05:00</TriggeredDateTime>
                    <NotificationEvent>InterimConditionsDeleted</NotificationEvent>
                    <InterimConditionsOrder orderEventKey="1760110">
                         <OrderDate>2005-07-20</OrderDate>
                         <OrderedBy judgeKey="00001J">
                              <JudgeName>
                                   <PersonGivenName>John</PersonGivenName>
                                   <PersonMiddleName>P.</PersonMiddleName>
                                   <PersonSurName>Smith</PersonSurName>
                                   <PersonFullName>Smith, John P.</PersonFullName>
                              </JudgeName>
                              <JudicialAgencyIdentifier>MN011015J</JudicialAgencyIdentifier>
                         </OrderedBy>
                         <CourtCaseNumber documentVersion="1" effectiveDateTime="2005-06-06T00:00:00-06:00">
                              <MNCISCaseNumber>
                                   <CountyNumber>87</CountyNumber>
                                   <CaseType>CR</CaseType>
                                   <YearFiled>05</YearFiled>
                                   <SequenceNumber>69</SequenceNumber>
                              </MNCISCaseNumber>
                              <CaseNumberIdentifier caseNumberKey="87CR0569">87-CR-05-69</CaseNumberIdentifier>
                         </CourtCaseNumber>
                         <ConditionSubject>
                              <Party partyKey="123637" currentNameIndicator="true">
                                   <StandardName>
                                        <PersonGivenName>Clanry</PersonGivenName>
                                        <PersonSurName>Ogavitz</PersonSurName>
                                        <PersonFullName>Ogavitz, Clanry</PersonFullName>
                                   </StandardName>
                                   <PartyCaseAssociationText>Defendant</PartyCaseAssociationText>
                              </Party>
                         </ConditionSubject>
                         <InterimConditions>
                              <InterimConditionText>Anger management</InterimConditionText>
                              <InterimConditionAmount>0</InterimConditionAmount>
                         </InterimConditions>
                         <InterimConditions>
                              <InterimConditionText>Attend AA (Alcoholics Anonymous)</InterimConditionText>
                              <InterimConditionAmount>5000</InterimConditionAmount>
                         </InterimConditions>
                    </InterimConditionsOrder>
               </InterimConditionsNotification>
          </CaseNotification>
The code is basically the same except that in the procedure the passing clause gets a differnt param, which is the passed in param from the procedure.
xmltable
                         xmlnamespaces
                         ---     'http://schemas.xmlsoap.org/soap/envelope/' as "saop",
                              'http://www.courts.state.mn.us/CourtXML/2.0.0' as "ic"
                         'for $ics in //ic:CaseNotification/ic:InterimConditionsNotification/ic:InterimConditionsOrder[@orderEventKey = $val/oeKey]/ic:InterimConditions
                         return
                         <ic:ICS>
                              <ic:ICSText>{$ics/ic:InterimConditionText}</ic:ICSText>
                              <ic:ICSAmount>{$ics/ic:InterimConditionAmount}</ic:ICSAmount>
                         </ic:ICS>'
                         passing p_XMLDoc, xmlelement("oeKey", v_OEKey) as "val"
                         columns
                         ICSText          varchar2(100)      path '/ic:ICS/ic:ICSText',
                         ICSAmount     number           path '/ic:ICS/ic:ICSAmount'
The strange thing is the procedure gets the ic:ICSText with the namespace value, which is http://www.courts.state.mn.us/CourtXML/2.0.0, so the finaly result is
the whole thing: <InterimConditionText xmlns="http://www.courts.state.mn.us/CourtXML/2.0.0">Anger management</InterimConditionText>.
I get the correct values when testing with the anonimous code!
What did I do wrong? Please help!
Thank you.
Ben

Hi gurus,
OK, I did another test. I ran the same PL/SQL anonymous block that gets the correct element value in 10.2.0.3.0 and it gets the same wrong value: the element name plus the namespace value and the data itself. It gets the correct element value in 10.2.0.1.0 (my local database).
Could anyone help me with this?
Thanks!
Ben

Please please please help me with this bizarre problem!!!

Hi there,
I am not an expert on web design and I am also not a complete newbie. I have built web designs before - and used frames and done it all on dreamweaver - however my target frames aren't working on this website and I'm not sure why???
I have two frames on my index page - one left and one right - the left is the menu and the right is the content of which ever button is selected from the menu in the left frame. However the targets don't work - when clicking on the buttons (links) it makes a new window pop up.
I have named the frames and saved the frame set as index.html.
The coding says for the shop button:
<td><a href="Shop.html" target="_right" onmouseover="MM_swapImage('Image4','','Images/Shop Button RO.jpg',1)" onmouseout="MM_swapImgRestore()"><img src="Images/Shop Button.jpg" name="Image4" width="163" height="56" border="0" id="Image4" /></a></td>
I have tried renaming the frames - tried a different computer - tried just about everything I can think of - it has always worked for me before but since building this site it doesn't! Have I missed something????
Please please help me - it's been driving me up the wall for 2 weeks!!!
Thanks in advance for yourhelp.
Pink
xxx

I haven't used frames since the late 1990s, so can't be of much help :-)
Here's a tutorial that may help:
http://www.dwfaq.com/tutorials/Frames/framesets1.asp
Page 4 shows how to link pages correctly
Is there a specific reason why you are still using frames... they are very old hat and hardly used anymore these days :-)
Here's the reason why frames are evil:
http://apptools.com/rants/framesevil.php
Nadia
Adobe® Community Expert : Dreamweaver
Unique CSS Templates | Tutorials | SEO Articles
http://www.DreamweaverResources.com
Web Design & Development
http://www.perrelink.com.au
http://twitter.com/nadiap

Please help me with this ipad problem

it like some kind of ios error it like it turned in to ipod,iphone ios
and i cant restore when i try it said an error occured 3194 or 1601 or 1600
and i try to restore in my ipad it didnt finish yet it is in progress for 1 day now!!!!!!
and my device is jailbreak but i didnt use installous i only use it for like winterboard and gravipad or barrel i buy all the app
PLEASE PLEASE HELP ME!!!!!!!!!!

I'm not good at English (i am thai) and what is op mean and yes you are right this is my other account.
Next time I will do better แบบทำเนี่ยนเนี่ยนอะไอ้เฟยเรามาขอให้ช่วยอแปไรเราก็ซื้อเองหมดอยากสนับสนุน apple ไม่เคยไช้เลยไอ้app cake ไรนั่นเราใช้แต่โปรแกรมเสริมเช่นwinter board barrel folder lock ไรเงี้ยเพราะ apple ไม่สามารถทำได

Please help me with an html problem

I am trying to get a one figure that I got from a jTextField to be displayed above a another figure in a different jTextField in a jTextArea. I have tried to use html whoever I have had some trouble doing so I have used the following code.
float num1, num2, a, b, result1, result2;
        num1 = Float.parseFloat(jTextField1.getText());
           a = num1;
            result1 = a;
                num2 = Float.parseFloat(jTextField2.getText());
                    b = num2;
                        result2 = b;
jTextArea1.setText(String.valueOf("<html>result1<br>result2"));The code displays <html>result1<br>result2" rather than the figures that I put into the jTextFields, which I did suspect it would it also displays it on the same line, which I did not suspect. Can anbody tell me how to display the figures in the two jTextFields in the JTextArea one above the other please. Thank you.

I guess I'll be honest with you the reason that I use a load floats is because I am very inexperienced at programming. I have only been programming for a month and have had to teach myself from books and internet documentation. I just found something that worked and repeated it over and over again and that is the reason. I know that my code looks very sloppy but it is the only way that I can do it because I am so inexperienced. The reason that I haven't learnt decent code is because I am working against the clock. I am a Freelance Macro Economist and have been working on l my own economic perspective tha could solve a lot of the economic problems in my country and some others too.
Unfortunately it is likely that there is going to be a large recession possibly world wide (mainly due to the high levels of debt). Anyway I have to develope a new taxation system to be able to control fiscal policy on a monthly basis so that there is a way of controlling inflation when the economy crashes because monetary policy works on the basis of people being in debt so if the economy crashes and people can't pay off the debt then monetary policy will no longer be able to control inflation.
Anyway to develope the taxation model I have to be able to prove that it can be altered on a monthly basis and that means that I have to write a computer program to do it. I have a degree in accounting an finance and have absolutely no expierence in computer programming but I only have a short time to complete my work.
I live in England and have actually had quite a lot of success with my work and have been working with three of the four main political parties. I don't know where you live but my work might help your economy too.
Anyway that's the reason why I am don't know what I am talking about.
Oh yeah Thank you for your help and I a having given you a duke star for providing me with a useful answer.

Please help me with Nokia N95 Problem.

If anyone can help with this I’d be much appreciated, I have a N95 on contract with T-Mobile. When I try to play videos from myspace, or you tube etc… I get a message telling me the following.
“Hello, Either you either have JavaScript turned off or an old version of macromedia's flash player click here to get the latest flash player”.
I then get the option of clicking on a link within the previous sentence statement that directs me to acrobat downloads home page where I get the following message.
“We are unable to locate a web player that matches your platform and browser. Please visit our table of recommended web players”
This is deeply frustrating as in nearly every other way I feel the phone is perfect. If Any one can hep me fix this problem I’d be much appreciated.

I'm in exactly the same situation as daperk... Love the phone BUTthe selling point for me was the internet access so when i began surfing found that most me the sites i went to i couldn't see the content and also would sometimes recieved a message saying i didn't have enough memory now considering i have a 2 gig card in it this didn't seem right i looked for any settings to allocate more space to internet browser but can't find anything... Regarding the utube program on the phone why supply it if it doesn't work?? I have the same problem i can see them in the menu but when i select one it doesn't play... I'm new here and only came here looking for a solution to the flash player issue but now i'm here i noticed posts refering to handsets crashing this i have to mention is another problem i have encountered... I'm doing something and the phone just freezes up leaving the only thing i can do is turn the power off and on to reset it... As i said at the start love the phone... But just wish it did what it said on the tin...

Please help me with my applecare problems

I got an applecare protection plan from apple when I got my imac (intel core duo). I entered everything on the first page and pressed continue. At the top it says 'Choose protection type' and has a -select- thing. I press it and there is only one choice. It is blank. After trying it and pressing next, it says please choose protection type 2600,39. (or some kind of random numbers, i dont remember) Is there something wrong with my serial number? Does this have to do with apple about to change serial number formats? PS: I tried it with my PC and the same thing happened.
HELP ME

Geowge,
Welcome to Apple Discussions!
Did you purchase your iMac directly from Apple, and did you purchase AppleCare at the same time? If so, your AppleCare plan should have been enrolled automatically. To check this, go the main Apple Support page here, and look on the right side of the screen where you will see a section marked, "About Your Support Coverage." Enter your serial number and click, "go." If your AppleCare has been enrolled successfully, you will see this information. If it indicates that you have only the one-year standard warranty, your best bet is to contact AppleCare administration at 800-275-2273.
I hope this helps.
Joe

Please help me with two Java problems

Hello,
I have 2 Java problems to work on and wondered if someone can help please?
1. I've created an array, but I have to now create a text file and write a program to read the array from the file. I have no idea where to start the program!
2.public class SumExample1 {
/* To determine if a number lies between 1 and 1000
* @param args the command line arguments
public static void main(String[] args) {
int num;
System.out.print("Enter a number: ");
num = TextIO.getInt();
if ((num >=1) && (num<=1000))
System.out.println("OK");
else
System.out.println ("Not OK");
Ive used a GUI to create some fields and buttons to press. How can I make it perform this little program?
Many thanks,
K

I recommend you read the tutorials on basic (file) IO and Swing (and Event Listeners if you want to make your GUI alive). Perhaps have a look at the Scanner class and BufferedInputStream. That should give you enough to start and write the program yourself. Try working in the command prompt first, should be easier, then once the logic works wrap it in a Swing GUI.
You can find the tutorials here:
http://download.oracle.com/javase/tutorial/
Swing:
http://download.oracle.com/javase/tutorial/uiswing/index.html
Basic IO:
http://download.oracle.com/javase/tutorial/essential/io/index.html
Hope this helps.
PR

Someone please help me with this sync problem

Ok here we go. I have had my laptop for a little over two years. Ever since i got my iphone 4 last summer it has been such a pain. I have backed up my phone and synced it multiple times on my computer. Every so often though i plug my iphone into the computer and it recognizes it in itunes but asks me to either set as new iphone or restore from back up. I have tried to restore from back up and it says that the back up has failed even though there is obviously a back up on the computer. I have set as new and it works fine for a day or two and then i got to resync and same problem. I have completly unistalled itunes and all its files and redownloaded it and it worked for a week or so and then same problem. I have also had my computer reset to factory settings (for an unrelated issue) and it worked the first time but then stopped working. I have tried everything i can imagine and am at the end of my rope with this phone. im so ready to call it quits and get something different cause this is so frustrating.

How do you do what? Plug the iPhone into a USB port directly on your computer, or disconnect other USB devices? To disconnect a USB device unplug it from the computer. If it is a disk drive eject it first using the Eject icon in the System Tray. To plug the iPhone into a USB port directly on the computer insert the USB end of the sync cable into a USB port on the computer.
If you are using all of the ports on your computer get a hub and plug low power devices into the hub (e.g., keyboard, mouse). Or get a hub with its own power supply and plug your high power devices (disk drives, DVD drive) into it.

Please Help me with this flash problem, my life is depending on this!

If you visit www.fishtv.tv there is a flash document on the
left side, it is a box with pictures scrolling. I NEED to know how
what to open it with, and how to add a picture into it. Please if
you have any information how to accomplish this task reply to this
thread, OR send me an email at [email protected] It will be
very much appreciated, thanks.

SWF is to FLA the same way JPG is to PSD. SWF is the compiled
(think flattened) format. Like urami
once said, you can't get the egg back after making the
omelette. There are SWF decompilers (search
google or this forum) out there but most will (if not all)
will merely allow you to obtain the
"guts" of an swf - you will not really end up with the
original FLA again. MUCH easier to try and
locate the FLA or rebuild the site. Surely there's a back-up
of the source somewhere?
--> **Adobe Certified Expert**
--> www.mudbubble.com
--> www.keyframer.com
willager wrote:
> i have the swf file, and i open it in flash and it shows
the final product, I dont know how to get it back to its orginal
file.

Please help me with PL/SQL problem

Hi to all
This is my problem. I have a database with several tables. I will mention just some important for this problem. I have a table called Invoice, where I have following atributes
sifrac number(9) not null primary key,
datrac date default sysdate,
sifkup number(5),
sifprod number(5) not null,
ukcena number(5,2)
Then I have table called History of customer where I have
constraint pk_istkup primary key(sifrac,sifkup),
sifrac number(9) constraint fk_sifrac2 references racun(sifrac),
sifkup number(5) constraint fk_sifkup3 references kupac(sifkup) this is primary key in a table customer,
datrac date default sysdate,
ukcena number(5,2) this is total price of purchased stuff per one invoice.
What I would like to do now is make a trigger before insert or update table Invoice which check table History of customer and make a calculation of all total prices per one customer and if that customer made a purchase which is more than 1000 dollars then it have to make a calculation of total price*discount percent.How can I do that.
Thanks to all in advance

Billy Verreynne wrote:
LKBrwn_DBA wrote:
This type of functionality (a business rule to compute discount) would normally be added at the application level and not in a trigger. Why? Does business rule code need Java to be expressed correctly? Does Java (or whatever application layer language) used provide a better set of instructions for doing business rules than PL/SQL? Is business code written using a special keyboard and a pretty font?
And what happens when new system feeds invoice data for new department/division directly into the database, bypassing the app layer? What happens to that app layer business logic now?
It is a fallacy that business rules and logic needs to reside in a separate layer as that is somehow better. I disagree. LKBrwn_DBA didn't mention Java as an application layer. And he was not strict about it. So yes it is possible to use a trigger. But business logic tends to be changed fequently. So the rules for the logic might change. I would implement such logic using a pacakged pl/sql api. Triggers I would use for data validations and checks that are less likely to be changed.
As always it depends. But the general advice to have a certain level of business logic (e.g. apis) and another level of data integration and consitency layer (e.g. constraints and triggers) is a good advice.
As for bypassing the application layer. If an new system is able to do that, it can wreck even more havoc. A good anti mechanism is to expose only the APIs layer in a separate schema. The new system will have access to the schema and to the packages that are specified there. But it won't have direct dml to the tables.
Main question for me would be: Is that a business rule or is it a data integration rule (e.g. keep redundant data in different tables harmonized). This influences where the logic will be implemented.
Edited by: Sven W. on Oct 2, 2009 8:59 AM

Please help me with the debugger problem

I got some error information from ST22 shows below.
Information on where terminated
Termination occurred in the ABAP program "CL_GUI_FRONTEND_SERVICES======CP" -
in "CONSTRUCTOR".
The main program was "SAPMSSY1 ".
In the source code you have the termination point in line 28
of the (Include) program "CL_GUI_FRONTEND_SERVICES======CM002".
I want to locate the codes where the error happens, so I think I can set a breakpoint at source codes as below, but the SAP system gives me the error: the breakpoints could not be created due to incorrect entry.
program: SAPMSSY1
include: CL_GUI_FRONTEND_SERVICES======CM002
row: 28
Could you please give me some ideas how to set the breakpoint? Thanks a lot.
Best,
Bing

Hi
Execute the program in the Debuggin mode.
In the Debugger Window
Select Breakpoint -> Break point at -> Breakpoint at source code Menu Item and enter the details of the program/include/line no..
Activate the System Debugger On from the Settings Menu.
Hope this would help you.
Murthy
Edited by: Kalyanam Seetha Rama Murthy on Jul 18, 2008 7:20 AM

Please help me with scsi HD Problem

Similar Messages

Maybe you are looking for