Please help,My speed has more than halved.

Hi
I have a 20mb line which i usually get about 10mb off,it has recently dropped to 1.5mb,and  everything is freezing and buffering here are my stats.Any help is greatly appreciated.
Connection information
Line state
Connected
Connection time
0 days, 3:25:06
Downstream
2,272 Kbps
Upstream
1,050 Kbps
ADSL settings
VPI/VCI
0/38
Type
PPPoA
Modulation
ITU-T G.992.5
Latency type
Interleaved
Noise margin (Down/Up)
32.0 dB / 5.5 dB
Line attenuation (Down/Up)
31.0 dB / 16.4 dB
Output power (Down/Up)
20.8 dBm / 12.4 dBm
Loss of Framing (Local)
26
Loss of Signal (Local)
2
Loss of Power (Local)
0
FEC Errors (Down/Up)
168 / 72
CRC Errors (Down/Up)
0 / N/A
HEC Errors (Down/Up)
N/A / 130313
Error Seconds (Local)
2

Hi you have a very high noise level which is what is causing your low speed i suggest you try these first Have you tried the quiet line test? - dial 17070 option 2 - should hear nothing - best done with a corded phone. if cordless phone you may hear a 'dull hum' which is normal
also you could try the hints given by poster RogerB in this link they may help http://community.bt.com/t5/BB-in-Home/Poor-Broadband-speed/m-p/14217#M8397
Then someone here may be able to help and offer more advice.
This is a customer to customer self help forum the only BT presence here are the forum moderators
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

Similar Messages

  • Speed's more than halved

    For a year or two we have had consistant speeds of around 230kbps download, which isn't exactly amazing, but it has done us fine. But since a few weeks ago the speeds have dropped to more than half of this at between 30-110kbps download.
    We changed router to the home hub about 2 months ago, but after having to deal with it's problems we swapped to an older router, however this broke and so we are back on the home hub. However our speeds have significantly dropped for no reason that we are aware of.
    I thought I should post here before calling BT and telling them. What can I do to bring the speed back up?
    I just did a speedtest on speedtester.bt.com and got this result;
    Download speedachieved during the test was - 803 Kbps
     For your connection, the acceptable range of speedsis 200-1000 Kbps.
     Additional Information:
     Your DSL Connection Rate :1427 Kbps(DOWN-STREAM), 899 Kbps(UP-STREAM)
     IP Profile for your line is - 1000 Kbps

    if you are regularly unplugging the leads or resetting the hub the both have the same effect in that the exchange thinks there is a line problem and increases the noise margin. The more you frequently reset the enchange ups the noise margin.  The optimum noise margin for the Hub is 6.  Without resets the hub will try to return to the optimum of 6 with a resulting increase in down sync.  Connecting to master socket may improve your connection
    If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
    If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

  • Broadband has more than halved in speed...why?

    Just switched to BT from TalkTalk (they were extremely slow, 2.5Mbps on a good day, and the internet went down every 5 minutes)
     Switch went ahead without a problem and we had speeds of approximately 6Mbps for the first few days. All extremely happy with the speed. Then, before the 10 day beginning period had finished, the speed plummeted down to 2.5Mbps and has stayed there. The 10 day period is now up. We are paying more for BT than for TalkTalk, and you've proved to us that you CAN provide us with a 6Mbps service. In fact, the details which came through estimated us at 8Mbps, with a PROMISED MINIMUM of 6 and a maximum of 12.
    Can anyone from BT please explain to me why you are delivering the same speed (2.5Mbps) as the previous ISP, when you are promising a MINUMUM of over double that, and charging more?

    Welcome to this forum. This is a BT domestic customer to customer help forum, any messages posted here do not go to BT. The only BT employees on this forum are the forum moderators.
    Its possible one of the forum members may be able to help you.
    To enable forum members to help you, please could you look at Helping forum members to help you which asks you to do a few checks first, and has some helpful hints.
    When you have done that, please post the results here, so members can offer advice. Thank you.
    There are some useful help pages here, for BT Broadband customers only, on my personal website.
    BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

  • Value help has more than 500 results

    Hi,
    We´re running CRM 2007 Version 6.0.
    I have integrated a field with a search help, that has more than 500 results. But in the search result popup only 500 results are shown. How can I provide access to the 500+ results to the enduser?
    I´m creating the search help via
    CREATE OBJECT rv_valuehelp_descriptor
        TYPE
          cl_bsp_wd_valuehelp_f4descr
        EXPORTING
          iv_help_id                  = 'search_help'   "search help name
          iv_help_id_kind             = if_bsp_wd_valuehelp_f4descr=>help_id_kind_name
          iv_input_mapping            = lt_inmap
          iv_output_mapping           = lt_outmap
          iv_trigger_submit           = abap_true.
    Thanks for help.
    Greetings,
    Sven

    Hi Sven Keller    ,
    u r using search help that u created in se11.Goto that search help there is a drop down(Dailog Type )
    in which 3 values r there.
    Select -
    A dailog depends on set of values or C dailog with value restriction ---as per ur need.
    see help for this field by pressing F1.
    regards,
    hem

  • An operation has more than one setup activity-error message

    Hi All,
    I have a queue which is failing and giving error message "An operation has more than one setup activity".
    I have  debugged it but of no use.
    In SAP R3 planned order data is created and is being sent to APO system through a CIF interface in queue.
    In APO system,planned order data is integrated to process order,during this they are getting the subject mentioned error.
    Kindly help me how to rectify this error.
    Please help...Thanks in advance.

    Hi,
    Back again...hopefully below should solve your issue.
    Check if any of the co-product (of the main assembly) has GR processing time. Are there any phantom component in the BOM, if yes, please check the co-products in phantom assembly as well.
    Any co-products /phantom assembly should be assigned to APO related Produce phase.
    Otherwise, you can remove the GR processing time for co-products (make it zero) and sync the master data and then try.
    This should solve the issue.
    Let know if this helps.
    Regards,
    NR

  • Error using JAX-WS to consume a WS that has more than one parameter

    I am trying to create a web service proxy in JDeveloper using JAX-WS for an OAM web service from a WSDL (identity/oblix/WebServices/CompositeWebServices/WSDL/um_view_interface.wsdl). I received the following error when I try to run the proxy:
    Exception in thread "main" com.sun.xml.ws.model.RuntimeModelerException: runtime modeler error: SEI test.profile.OblixIDXMLPortType has method oblixIDXMLUmView annotated as BARE but it has more than one parameter bound to body. This is invalid. Please annotate the method with annotation: @SOAPBinding(parameterStyle=SOAPBinding.ParameterStyle.WRAPPED)
    at com.sun.xml.ws.model.RuntimeModeler.validateDocBare(RuntimeModeler.java:1267)
    at com.sun.xml.ws.model.RuntimeModeler.processDocBareMethod(RuntimeModeler.java:1256)
    at com.sun.xml.ws.model.RuntimeModeler.processMethod(RuntimeModeler.java:628)
    at com.sun.xml.ws.model.RuntimeModeler.processClass(RuntimeModeler.java:416)
    at com.sun.xml.ws.model.RuntimeModeler.buildRuntimeModel(RuntimeModeler.java:267)
    at com.sun.xml.ws.client.WSServiceDelegate.buildRuntimeModel(WSServiceDelegate.java:715)
    at weblogic.wsee.jaxws.spi.WLSProvider$ServiceDelegate.buildRuntimeModel(WLSProvider.java:427)
    at com.sun.xml.ws.client.WSServiceDelegate.addSEI(WSServiceDelegate.java:703)
    at com.sun.xml.ws.client.WSServiceDelegate.getPort(WSServiceDelegate.java:347)
    at weblogic.wsee.jaxws.spi.WLSProvider$ServiceDelegate.getPort(WLSProvider.java:409)
    at com.sun.xml.ws.client.WSServiceDelegate.getPort(WSServiceDelegate.java:330)
    at com.sun.xml.ws.client.WSServiceDelegate.getPort(WSServiceDelegate.java:312)
    at javax.xml.ws.Service.getPort(Service.java:92)
    at test.profile.OblixIDXMLService.getOblixIDXMLPort(OblixIDXMLService.java:79)
    at test.profile.OblixIDXMLPortClient.main(OblixIDXMLPortClient.java:23)
    Process exited with exit code 1.
    It seems like the OAM web service (um_view_interface.wsdl) is not WS-I BP 1.1 compliant. It expects two elements under the body. WS-I BP 1.1 specifies that there should be only one child in the body of the element.
    The expected request body would look like this, there are two elements under the body:
    <soapenv:Body>
    <authentication xmlns="http://www.oblix.com/">
    <login>loginname</login>
    <password>pass</password>
    <domain>dc=test,dc=org</domain>
    </authentication>
    <request application="userservcenter" function="view" mode="dataonly" version="NPWSDL1.0" xmlns="http://www.oblix.com/OblixXMLLocalSchema">
    <params xmlns="">
    <ns1:uid xmlns:ns1="http://www.oblix.com/">cn=tester,cn=Users,dc=test,dc=org</ns1:uid>
    </params>
    </request>
    </soapenv:Body>
    Has anyone encountered the similar problem? Is there a solution to this problem?
    Your help is appreciated!

    Can u pls share ur solution if u have found a way 2 create a web service with 2 ports.I have not yet found a solution so far and nobody reacted to all my posts in the different fourms. It seems nobody is implementing web services with two ports using the EJB annotations technology.

  • Need help in EMAIL Sending -  more than 255 character length

    Hi Guys,
    Please help me in sending the Email attachment which has more than 255 character lengh using 'TXT format.
    if i create an internal table having a field of type char225.
    then break ur each record into many parts having len <= 255.
    how can i mingle both lines to single line in the output list.
    Please help me ..
    thanks in advance..
    Prabhu

    Hi,
    Check the following link:
    http://www.sap-img.com/abap/sending-email-with-attachment.htm
    Regards,
    Bhaskar

  • Material has more than one plant, only show the price for the first on

    Hi:
    I am having the standard price for the material with the different plants ,I am seeing only one Material and Standard price(if a material has more than one plant, only show the price for the first one In the report ):
    plant :de87 Material: 60020601 Standard price: 1237.00
    plant:PT01 Material :60020601 Standard price: 634.00
    In the report I am seeing DE87 with the standard price :1237.00 .
    I am extracting from the 0MATERIAL_ATTR
    Please help me how can I display all plants with the material and std price. In my data source there is no PLANT
    rgrds
    Kumar

    Hi:
    Report is running on 0MATERIAL(Transactional master data),Data sourc: 0MATERIAL_ATTR,
    We are having the standard price in the 0MATERIAL ,(Standard price is combination of plant and Material) .Plant is not available in the material,so in the report its displaying only first result
    plant :de87 Material: 60020601 Standard price: 1237.00 --->Displaying this
    plant:PT01 Material :60020601 Standard price: 634.00
    In the above we are having the same material but different plant and different standard price. so I need to display the both in the report.
    Rgrds
    kumar

  • How to print a graph in which internal table has more than 32 entries?

    hiii experts
    i am trying to make a line graph using 'gfw_pres_show' function module.
    but in report internal table has more than 32 entries
    so how can i print a graph having more than 32 entries?

    Hi ricky_lv,
    According to your description, there is main report and subreport in it, when the subreport spans across multiple pages, you want to show column headers on each page. If that is the case, we can set column headers visible while scrolling in main report.
    For detail information, please refer to the following steps:
    In design mode, click the small drop down arrow next to Column Groups and select Advanced Mode.
    Go to your Row Groups pane, click on the first static member.
    In properties grid, set FixData to True.
    Set RepeatOnNextPage to True.
    Here is a relevant thread you can reference:
    https://social.technet.microsoft.com/Forums/en-US/e1f67cec-8fa3-4c5d-86ba-28b57fc4a211/keep-header-rows-visible-while-scrolling?forum=sqlreportingservi
    The following screenshots are for your reference:
    If you have any more questions, please feel free to ask.
    Thanks,
    Wendy Fu
    If you have any feedback on our support, please click
    here.
    Wendy Fu
    TechNet Community Support

  • Auto creation of child requests when parent request has more than one group

    Hi,
    I have created a request dataset which has a child form for AD Group. While raising a request, if I add more than one group, how to process the approval flow. Because I will be having different different approvers for different different groups. Is there any way to create child requests automatically when we submit a request with more than one group? I am using OIM 11.1.1.5.0.
    I know in OIM 11g, whenever user raises request for more than one beneficiary/target-resource then OIM breaks that request into Child Requests. But this is not happening when I add more than one group in the same resource. Do I need to write my own code for DataValidator to split parent request into child requests upon validating child form? If so, is it going to impact the existing feature which is creating child request when parent has more than one user/resource.
    Please let me know.

    No not possible OOTB in current version. Check {thread:id=2318652} for more information.
    -Bikash

  • While clearing document has more than 999 line items system not allowing

    Hi,
    We have an issue with FI-Customer Clearing. While clearing the error is appearing as document has more than 999 line items. after the detailed checking we found that there are lots of line items posted to Real Exchange Rate diff that to COPA.
    To reduce the maximum line items SAP is suggesting to deactivate the Real exchange rate diff.postings to COPA.
    Regards,
    R.Kumar.

    Hi,
    Please check SAP Note 1353125
    Thanks

  • Slow script warning when prompt choice list has more than 100 elements

    Hi,
    Has anyone experienced this issue in Internet Explorer version 7 and above? If the prompt has more than 100 elements (my current use-case), the prompt does not get rendered and I get the slow/busy script warning in Internet Explorer. I have not experienced this in Firefox or Chrome.
    Any help is appreciated
    OBIEE 11.1.1.5

    Thanks you, friends!
    That to resolve my issue, i made next things:
    1) turn off a limit items for my list
    2) used SPQuery.ListItemCollectionPosition
    property,
    3) and corrected little mistake in my CAML Query.
    May be a punkt #2 will be enough, don't you :)
    from MSDN forum...

  • Problem with closing other firefox windows when window in use has more than 1 tab open

    If I have multiple firefox windows open, and the one that I am using has more than one tab open, when I try to close one of the windows that I am not using by hovering over the firefox icon on the taskbar, then clicking the cross on the other windows, a message appears asking me if I want to close a window with more than one tab open. This means that firefox is trying to close the window that I'm using, not the one I'm trying to close. Please note this only happens when I hover over the icon on the taskbar then click the cross for the window I want to close. If I open the window properly, then click the cross on the window itself, it works fine.
    Just wanted to know if anyone else has this problem, and if they do, then mozilla should probably fix it in their next update, it's getting really annoying now

    I can't find a bug on file for this on https://bugzilla.mozilla.org/ (although there are many taskbar-related issues under review).
    (1) Just to confirm, do you both have "Show tab previews in the Windows taskbar" turned off here:
    orange Firefox button (or Tools menu) > Options > Tabs
    (2) Have you tried disabling Firefox use of hardware graphics acceleration?
    You usually need to restart Firefox in order for this to take effect, so save all work first (e.g., mail you are composing, online documents you're editing, etc.).
    orange Firefox button (or Tools menu) > Options > Advanced
    On the "General" mini-tab, uncheck the box for "Use hardware acceleration when available"
    If you restart Firefox, do you notice any changes?

  • Dynamic Calc member has more than 100 children

    In my db, I've a dynamic calc member, in say hierarchy Accounts, that has more than 100 members under it (children).
    I'm using MaxL scripts to update the Accounts hierarchy i.e. adding new members, tagging UDA's etc.
    However, the MaxL command is erroring out with a Network Error: Cannot Recieve/Send data. I understand if I try doing the update via
    EAS and try to save the outline, it gives me the more than 100 children warning but still allows me to save it but via MaxL I cannot force
    it to do so.
    This is just a warning and shouldn't MaxL still save the outline? Is there something else that am missing or is there any solution for this issue.
    This is a Sparse dimension. More members will be added to the hierarchy monthly, thereby not reducing the count below hundred.
    Any help/advise is much appreciated. Thanks.
    @deepak

    I am envisioning an entire sparse Accounts dimension with all of the upper levels dynamic. If it is like most accounts dimensions I have seen it has a lot of level zero members and a lot of parent rollups. looking at top level members could be very slow (relative to if they were calculated or dense). We have all done interesting things in our cubes to gain some performance measure trading off calculation and retrieval performance. Doing something like this is an area where a testing is crital

  • VLD-0201:Table has more than one primary key

    hi
    i'm working with OWB 9.2,I was imported the table from database,when i validating that it is giving message:
    VLD-0201:Table has more than one primary key
    vld-0209:Duplicate unique key i.e:cust_acc and SYS_C00435 detected.
    Can i use this table and generate the mapping with out any errors?
    Any help will be very generate.

    Hi Ashok,
    I'm quite curious how you managed to get a table with 2 PK's.
    I tried it myself:
    =======================================================
    SQL>create table x(c1 number constraint pk1 primary key,c2 number constraint pk2 primary key, c3 date);
    create table x(c1 number constraint pk1 primary key,c2 number constraint pk2 primary key, c3 date)
    ERROR at line 1:
    ORA-02260: table can have only one primary key
    SQL>ed
    Wrote file afiedt.buf
    1* create table x(c1 number constraint uk1 unique,c2 number constraint uk2 unique, c3 date)
    SQL>/
    Table created.
    =====================================================
    As you can see, trying to create a table with more than 1 PK is impossible. With Unique Key, that IS possible (see second example).
    I don't expect mappings to function properly with such an error message.
    Is it possible for you to drop the table in the database, correct the definition of the table in OWB and then deploy that corrected version to the database?
    If on the other hand the table on the database is correct (i.e. has only one PK) then the import into OWB obviously did not go well and I'd suggest you drop the imported definition and try to import it again.
    Cheers, Patrick

Maybe you are looking for