Please help: programs shut down after 60 sec's

*Please help me:* Since two weeks or so (may be, after I updated my QuickTime), every program I opened *shuts down after roughly 60 seconds*. It is not closed but it gets out of the writing mode so that I need to click on the page first before being able to continue writing again (Word, email, also this thread). If I do not always look at my page I loose words and have to retype them again. Also, with backspacing it occurs: it gets out of the enter mode. I am not aware I changed anything in the user mode of my dear power book.
Thank you for helping! rororoger

rororoger:
Welcome to Apple Discussions.
Try starting up in Safe Mode. If can do so successfully, log in, Empty Trash, Restart normally and log in.
If issue persists Repair Disk
Insert Installer disk and Restart, holding down the "C" key until grey Apple appears.
Go to Installer menu (Panther and earlier) or Utilities menu (Tiger) and launch Disk Utility.
Select your HDD (manufacturer ID) in the left panel.
Select First Aid in the Main panel.
(Check S.M.A.R.T Status of HDD at the bottom of right panel, and report if it says anything but Verified)
Click Repair Disk on the bottom right.
If DU reports disk does not need repairs quit DU and restart.
If DU reports errors Repair again and again until DU reports disk is repaired.
If DU reports errors it cannot repair you will need to use a utility like Tech Tool Pro or Disk Warrior
cornelius

Similar Messages

  • I have joined adobe photoshop but the program shut down after just one minute, why? I cannot use it!

    I have joined adobe photoshop but the program shut down after just one minute, why? I cannot use it!

    Without proper system information and other details nobody can tell you anything. If the program shuts down after a while then presumably it fails to verify your activation, so refer to this:
    Sign in, activation, or connection errors | CS5.5 and later
    Mylenium

  • HELP Program shuts down when try to capture video

    Every time I click on capture the program shuts down. I've used this program many times with no problem but now it won't even reconize my camera. And when I try to capture it shuts down completely. Anyone know what to do?

    There is nothing wrong with FCE 2 as a program - it should not be necessary to upgrade it.
    Have you tried plugging and unplugging the FireWire cable from both the computer and the camera.
    Also see if iMovie will recognise the camera. if it won't you will know the problem is probably not the fault of FCE.
    It is also possible that FCE may be corrupted in which case you should re-install it after having first uninstalled it by deleting ALL the files listed in this article:-
    http://docs.info.apple.com/article.html?artnum=93688
    Good Luck.
    Ian.

  • Need Help--G450 Shuts down after few miutes

    I have a G450 laptop, purchased in the month of June. I am using Win 7. From yesterdays onwrads when ever i am switching it on it gets shut down with in few minutes. After taht if I am restarting it never restarted. I left it for 30 Minutes and then try to switch it on. It again restarted but with in few minutes ir shut down. The laptop is not getting heated up, so I do not think its a problem of Heat Sink and Fan Issue. Please help....

    press f8 to load safe mode and check if issue persists.
    or try to perform clean windows installation.

  • Please help - applications shutting down randomly

    Evening everyone,
    I've used macs for a few years now and am in the process of moving my mum from the crappy family PC over to my old iMac G5, which is just over 3 years old. The G5 is staying at home so mum can use it and I'm going back to uni on Tuesday with my MacBook.
    I've set mum up with a new user account, her iPhoto library is on the computer but the iTunes library and a load of backup stuff is on a Western Digital My Book Home edition external hard drive as there's not enough room on the G5. Just as I was starting to show mum how to use the mac (at times a painful process - she's not the best at learning new computer things) the G5 went and showed me up. It's being pretty slow at opening applications and loading photos in iPhoto and it is also quitting applications without any notice or obvious cause.
    The problem seems to be only in mum's user account which confuses me as it's pretty much pristine. I've scanned it with ClamxAV for viruses and found none and am in the process of scanning the external HD. One weird thing is that sometimes (but not all) after an app has shut itself down unannounced a finder window will open at a specific folder on the WD Hard Drive. It's a random photo file, originally I had mum's iPhoto library on the external drive but have sinced freed plenty of space for it on the G5 hard drive as I feel its more reliable, but there are still copies of all the photos on the hard drive. I really cant see why it sometimes links back to this one though.
    Sorry, I know this is a really long post but thought I'd try and give as much info as possible - I need to get this sorted before I go back to uni on Tuesday otherwise mum won't be able to use the computer and I'm not back again until Christmas! I'd really appreciate your help and any ideas/suggestions you guys could offer. These forums have always been very useful for troubleshooting in the past, just hope my first post can work out as well!

    The following may help:
    Help - a program unexpectedly
    Apps unexpectedly quit

  • Please help me shut down imessage from the computer?

    Hello,
    I've recently sold my Iphone and unfortunatelly iMessage is still activated on it so I'm not receiving messages from my Iphone friends... I've tried and deleted the phone as one of my products on apples account but this didn't helped I have my apple account info and the serial number of the phone as well as the telephone number it's connected to... Thank you in advance for any help guys!
    Apple account: [email protected]
    Serial number: 7R1131M4A4S
    Phone number: +46 761110115

    Asked and answerd many times...
    http://support.apple.com/kb/ts5185

  • AFTER UPDATE GREY SCREEN NO SOUND THEN SHUTS DOWN AFTER 30  SECONDS PLEASE HELP

    AFTER UPDATE GREY SCREEN APPEARS WHEN POWER BUTTON PRESSED NO START UP SOUND THEN SHUTS DOWN AFTER 30  SECONDS AND REPEATS ITS SELF PLEASE HELP

    As for now, only thing that helped was an archive and install with preserve user settings. Seems after the reinstall of 10.4. everything that was weird has become normal again. I hope very much this state stays on for a while - or ever!
    A comment to everybody: with problems that are common you get a lot of help from friendly users in here, but if like in my situation things get a bit more uncommon than the usual querks and troubles your bound to go through a whole workflow of tests and algorithms - i did learn some new things but eventually I had to go for the ultimate - the reinstall (of course, erase and install would have been more work.) and it's frustrating not to find out how it came to this problem. I wish I could nail it down to something I did mistakenly - i guess I'll find out next time.
    THANKS THOUGH to those who replied.
    Keywan

  • When running on battery power, my MBP shuts down after 30 mins..please help

    this has been happening for the last two weeks; whenever i run my MBP on battery, it goes blank/shuts down after about 30 mins...would start back on, but shut down even before the login screen comes! i checked the battery display under the laptop-it showed 3 green lights!! TIA!! i bought my MBP off the apple website last september!

    With your symptoms, most likely, yes. If you have a 17" MBP, you are out of spec (based on Apple's specification of 80% health for 300 cycles). If you have a 15" MBP, you're in spec (84% health), but your symptoms indicate a problem (i.e. a defective battery). So, contact AppleCare!
    You can't calibrate now. I asked because if a battery goes too long (150-220 cycles) without calibration, the "sudden loss of power" can result.
    Hope this helps...
    Graham, that's why I inquired about calibration, but with the OP's cycle count, that's not the issue. Also, FYI the "battery condition" information is part of System Profiler with Leopard; the OP lists Tiger, and did post all the information available under Tiger.

  • Hi my iMAc 27 inch starts up to the grey screen with apple logo and loading bar underneath it loads halfway then freezes up and shut down after a while please help

    Hi my iMAc 27 inch starts up to the grey screen with apple logo and loading bar underneath it loads halfway then freezes up and shut down after a while please help

    Try the tips listed here Mac OS X: Gray screen appears during startup - Apple Support

  • Flash shuts down after start up screen - please help

    I had a strange problem develop yesterday. Whenever I start
    Flash 8 the start up screen shows for a moment, then disappears and
    the program shuts down and never starts. I ran Ad-Aware, Spybot,
    HijackThis and even did a file search by date to see if anything
    appeared on my computer that would cause this but I found nothing.
    I have Flash MX installed as well and it was doing the same thing
    when I tried that. I repair/installed Flash 8 - didn't work, then
    uninstalled Flash 8 and installed again and it's still doing the
    same thing. I suppose I could uninstall MX too and try again but I
    suspect that's not the problem. Any thoughts?

    Your capacitors are leaking, this is a known issue with Rev A G5 iMacs, and they should be replaced, along with the logic board. Take it in and if t stays up long enough, try to clone it to an external drive to save your data. I use SuperDuper! to do this.
    Let us know how you make out,

  • Help! While editing a photo in CS3 the program shut down and will not reopen my psd file.

    Help! While editing a photo in CS3 the program shut down and will not reopen my psd file. The error message reads "cannot complete your request because of a program error" -- it is a very large file (I have been saving it all along) and I had just "flattened layers" and went to open up a new, blank photo file when it shut down. Is there anyway to get this file to open? Any advice would be greatly appreciated! (p.s. after reading a couple of similar threads, I have a feeling it's hopeless. But I'd also like to know WHY this might have happened!) Thanks in advance!

    Thank you. I appreciate you taking the time to respond and for sharing the article--I did panic. Here are the details of my system:
    Model: HP p7-1247c
    Processor: AMD A8-3820 APU with Radeon HD Graphics
    Installed Memory: 8 GB (7.48 usable)
    System Type: 64-bit
    Windows 7 Home Premium
    I am using Photoshop CS3. It seems that I can work on photos and save them. But I am unable to open them back up. I have tried saving the files as psd and tiff with the same result. The error message is:  "cannot complete your request because of a program error"
    The interesting thing is that I can open up InDesign and "place" the psd file within InDesign (then export and save as a jpeg). So I don't think the files are necessarily corrupted. I uninstalled Photoshop and reinstalled it last night, but there's no change.
    If you have any ideas, I'd appreciate it. Or, should I repost my question with this more complete info? Thank you!

  • EXTERNAL HD WONT SHUT DOWN AFTER SHUTTING DOWN LOGIC ,HELP

    When Im done recording in logic and after I close down the session and shut logic down. I then try to shut down my external HD and I get a message saying " LOGIC IS STILL IN USE AND EXTERNAL HD CAN NOT BE SHUT DOWN, TRY QUITTING APPLICATIONS AND THEN SHUT DOWN" Logic is already shut down and there are no other applications running and it wont let me shut down my external HD. I tried to switch HD's and it still wont shut down after I close all applications. PLEASE HELP....
    Message was edited by: philip j

    When you say shut down, you mean "eject" right?
    Will it, incidently, eject during a session when you haven't used Logic at all?
    One thing you should make sure of with your external HD is that it is formatted correctly - it needs to "un" journalled... may not be the problem, but worth checking.
    What kind of external HD is it?

  • How can I Recover an iMovie project after the program shuts down unexpectedly?

    I was working on an iMovie when the program shut down unexpectedly.  I had worked on this project many times before and it always showed up in my project library.  After the shutdown, however, I tried to open up the project and it is no longer in the project library.  I can find it in the finder but when I click on it, it will open iMovie but the project is not listed.  It has to be in there somewhere!  How can I recover it?  Please hlep!

    There are numerous reports here on the forum about this issue (I've been bitten by it too). It's becoming an epidemic.
    Here's one thread:
    https://discussions.apple.com/message/21157327#21157327
    The recent update to iMovie '11 (to version 9.0.9) may have fixed this, but it's impracticable to test, given the random nature of the problem.
    The best solution is to always have Time Machine running when editing in iMovie. Also, with larger projects, it's a good idea to duplicate the project from time to time. To duplicate, while in Project Library view (where all your projects are listed), select File > Duplicate Project. Project files are relatively small, as they mainly reference the associated Event (or Events), as well as keeping track of your edits, titles, transitions, music and so forth.
    John

  • Mail shuts down after 3 secs on ipad 1

    Can anyone help with this, my mail shuts down after approx 3 secs of opening on my ipad, have cleared all mail from desk top pc but still happens??

    Try turning the account off and on : Settings > Mail, Contacts, Calendars , then tap the account on the right, slide Mail to 'off', exit settings and go back into the Mail app, and then go back to Settings and slide Mail back to 'on'
    If that doesn't work then try closing the Mail app completely : from the home screen (i.e.not with the Mail app 'open' on-screen) double-click the home button to bring up the taskbar, then press and hold any of the apps on the taskbar for a couple of seconds or so until they start shaking, then press the '-' in the top left of the Mail app to close it, and touch any part of the screen above the taskbar so as to stop the shaking and close the taskbar.
    Also do a reset : press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.

  • Mac shuts down after 5 minutes  Help!!!!

    My computer: imac G3, DV Special Edition, 500Mhz, 384 mb ram, 80 gig hard drive
    This is an odd one...like many others before me the computer just died one day. it would not start up, no sounds, just dead. A few minutes later I tried to turn it on and it came on, but 5 minutes later, it died.
    This is the strange part. I took the plug from the socket and waited a few minutes, then pluged the computer back up. It came on. But only for a few mintes and again shut off.
    This time I left the plug in the socket, waited a few minutes and tried again. Nothing.
    I then took the plug out waited about 30 minutes and it came back on for about 5 minutes and shut down. It only seems to come on if I let the computer sit idle with the plug out.
    I have noticed that the computer does not keep time properly.
    What I have done.
    1. I have pressed the Cuda Button, and yes it did start up, but only for about 5 minutes.
    2. I have tried to reinstall the system hardware, but the computer dies before completion.
    Should I replace the battery? What else can be done?
    Help!

    I have the same problem. I don't have good news, though. I have replaced the battery, pressed the reset button, even replaced the power supply board (not the video board -- which is the only thing I have decided I'm not willing to do). My computer usually shuts down after 5 minutes, but will sometimes stay working fine for a couple of hours. I managed to update the firmware and OS to the very latest, but still it dies. Mine will also occasionally flicker and freeze, which can be restarted by holding down the power button.
    I would replace the video board, except the people trying that don't have quite the same problem (theirs don't start up at all), and there is no source I've found that would have new boards, so you would get a bad board, or the same problem eventually. Some people point to a transformer on the video board, but again the symtoms are not quite the same (they smell burt electronics or hear a hissing/crackling sound before it dies.
    I have just packed mine away and I'm working on a new G5, but I sure hope the old iMac can be fixed so my kids can use it. I just didn't want you to have to go down the same road just to find nothing helped. Good luck, and if you have any new ideas, I would be glad to hear them.

Maybe you are looking for

  • Itunes won't display my episode descriptions

    Hey, I'm hoping someone can help me out. I'm pretty new at this. I just submitted my first podcast to itunes and the listing won't display me episode descriptions. Would someone be so kind as to check my RSS file? The URL of the RSS file is www.indig

  • Mapping with dynamic sql

    Ok boys, another homework problem gone awry... I'm trying to create a mapping function to sort by NAME...here's the code: ----------CREATE MEMBER----------------- CREATE OR REPLACE TYPE BODY item_ot AS   MEMBER FUNCTION mapping    RETURN VARCHAR2 IS

  • My imac is getting slower. Is there a tool to get rid of waist (temp files etc.)

    I am sure there is a tool in the apple software availabe, to speed up again may iMac.

  • IPhone crashing and locking up

    iPhone locking up mainly using safari. Having to do a hard reset to recover. Is anyone having the same problem? Has during other apps besides safari. I hope they are planning a firmware update real soon. Makes a great iPod though.

  • Related to struts validation form

    Hi all, When entering validations on a form in validation.xml, If you have a fieldA with "depends=required,maxlength" and FieldB with "depends=required,email". If when i give fieldA with 40characters but its permitted length is 20 and FieldB is empty