Please help!! - usb power problems

Hi guys,
i posted this on the USB board but no one has been able to help me so far. I am having the following, very frustrating problem:
Hope someone can help me out. I bought a belkin 7 port usb2 hub and it has been working perfectly until 2 weeks ago. I now keep on getting low power warnings when i plug it into my computers usb 2 ports. So far i have done the following:
1) replaced usb hub for a new one.
2) checked the hub works with windows machine usb 2 ports - it does.
3) reset the power supply to the usb port (unplugged mac for 10 mins, held down power button while it is unplugged, then plugged it back in) - searched for this on apple help pages.
4) checked all USB ports work - they do.
5) checked these forums and can;t find anything.
6) Have reinstalled OS X
System profiler recognises the hub and displays the following information about it;
Hub:
Version: 0.00
Bus Power (mA): 500
Speed: Up to 480 Mb/sec
Product ID: 0x0237
Vendor ID: 0x050d
When i start up the computer the green lights on the hub all flash and then disappear.
I have recently bought a new ipod shuffle and it has caused all types of start up and standby problems with the computer (computer wont start up if it is attached and wont standby if it is attached). Could this have caused the problem? I have now disconnected the shuffle from the hub and still it doesn't work
In my mind (which is not that technical) if I can reboot the USB ports it should work again. Is that correct? How would I do it?
Sorry for such a long and rambling post, I can't think of a logical explanation for it to no longer work.
Many thanks in advance for any help or advice
20 inch intel imac Mac OS X (10.4.8)

Hi, I use the same hub,,a suggestion..turn every
OFF..unplug ALL cables to mac..and hub.
Reconnect just power/keyboard/mouse & hub -
Restart..
if everything is ok - add 1 usb at a time -
restarting each time
I did this & everything was fine N dandy -- if you
have a faulty item it will show up when you restart -
Also have you reset everything & done Permissions
etc..L
Thanks, just tried that but the computer wont even let me plug the hub in on its own without flashing up the low power notice. Something is telling the computer that it can't power the hub, just after start up. not sure what though...

Similar Messages

My Itunes is no longer allowing me to manage my music on my phone i can no longer select on my iphone to make playlists and delete music. Please help fix my problem.

My Itunes is no longer allowing me to manage my music on my phone i can no longer select on my iphone to make playlists and delete music. Please help fix my problem. Iphone4s, 32gigs, IOS 7.1.2
I don't know why it stopped working but it happened a month or two ago but the option on this phone that's usually all the way to the left when you select your device but now its not and I don't know what caused it. ive already tried troubleshooting my problem but have found no help.

Hello Salmomma,
Thank you for the details of the issue you are experiencing when trying to connect your iPhone to your Mac. I recommend following the steps in the tutorial below for an issue like this:
iPhone not appearing in iTunes
http://www.apple.com/support/iphone/assistant/itunes/
Additionally, you can delete music directly from the iPhone by swiping the song:
Delete a song from iPhone: In Songs, swipe the song, then tap Delete.
iPhone User Guide
http://manuals.info.apple.com/MANUALS/1000/MA1658/en_US/iphone_ios6_user_guide.p df
Thank you for using Apple Support Communities.
Best,
Sheila M.

[ETL]Could you please help with a problem accessing UML stereotype attributes ?

Hi all,
Could you please help with a problem accessing UML stereotype attributes and their values ?
Here is the description :
-I created a UML model with Papyrus tool and I applied MARTE profile to this UML model.
-Then, I applied <<PaStep>> stereotype to an AcceptEventAction ( which is one of the element that I created in this model ), and set the extOpDemand property of the stereotype to 2.7 with Papyrus.
-Now In the ETL file, I can find the stereotype property of extOpDemand as follows :
s.attribute.selectOne(a|a.name="extOpDemand") , where s is a variable of type Stereotype.
-However I can't access the value 2.7 of the extOpDemand attribute of the <<PaStep>> Stereotype. How do I do that ?
Please help
Thank you

Hi Dimitris,
Thank you , a minimal example is provided now.
Version of the Epsilon that I am using is : ( Epsilon Core 1.2.0.201408251031 org.eclipse.epsilon.core.feature.feature.group Eclipse.org)
Instructions for reproducing the problem :
1-Run the uml2etl.etl transformation with the supplied launch configuration.
2-Open lqn.model.
There are two folders inside MinimalExample folder, the one which is called MinimalExample has 4 files, model.uml , lqn.model, uml2lqn.etl and MinimalExampleTransformation.launch.
The other folder which is LQN has four files. (.project),LQN.emf,LQN.ecore and untitled.model which is an example model conforming to the LQN metamodel to see how the model looks like.
Thank you
Mana

HT5312 i forgot my secret question, please help me this problem. Thanks

I forgot my secret question, please help me this problem. Thanks

Contact iTunes Customer Service and request assistance
Use this Link > Apple Support iTunes Store Contact
And/or see the More Like This section on the right.

Please help with slideshow problems!

Am using Photoshop Elements 8 and trying to make a slideshow. Have tried 4 times now and keep ending up with same problem, cannot reopen project to continue edititing. Won't show up in orginizer and when I find on harddrive and try to open get message " wmv file cannot be opened". How can I save a
slideshow inprogress and be able to reopen and continue to edit and make slideshow? I want to thank anyone who can help me with this in advance as I
have gotten so frustrated that I want to just scream.
Thanks

Thanks for the help, thought I had done so but maybe not. Anyway will have another go at it, now may I ask another
question? I am trying to add audio to slideshow. I have some music I purchased thru amazon as mp3 files but I get
message no codec and when I try to add wmv I get same message. What type of file do I need and how can I add
multiple songs to one slideshow. I have one little wmv file that will go in, but it just replicates itself multiple times until
it fills slide show.
Thanks again, sorry to be a bother, but this thing is driving this old man crazy.
Date: Sun, 26 Dec 2010 20:34:32 -0700
From: [email protected]
To: [email protected]
Subject: Please help with slideshow problems!
You need to save the slideshow project in order to be able to go back later and make changes or additions to an existing slideshow . The wmv file is a final output format.
Now you are most probably using only the Output command: that is what makes the wmv file.
You should also do the Save Project command. (and I make it a practice to do the Save Project command before I do the Output command).
If you look at the Elements Organizer 8 Help, there is a topic on "Create a slide show".
-- Very close to the beginning of that topic is a screen shot of the Sldie Show Editor screen,
-- The bar below the usual menu bar is labeled with a "B" and called the Shortcuts bar.
-- The 1st entry on that Shortcuts bar is "Save Project"
It is the Save Project command that saves the information about which photos, audio, etc you placed in that specific slide show so that you can come back again to do subsequent editing. Save each Project with a unique name.
After completing the Save Project command, you shoud see an "icon" in the Organizer for that slide show.
Note: you must also keep the photo files and audio files which you have used in this slide show: you can't delete them because the project file does NOT contain a copy of the photos, it only has the identification and folder location of the photo and audio files.
>

PLEASE HELP.. PROBLEM WITH RESTORE

okey, well i have this huge problem. i got my ipod 2 weeks ago from the US, i live in poland and not many people know how these things work so i ask that someone here can help me..
a week ago.. the ipod froze my computer, i could do nothing with it. so i had to restart it.the problem was that my ipod was connected to the computer still.. but my comp wouldnt start so i had to disconnect the ipod.(yes the DO NOT DISCONNECT icon was on the ipod.. but wut else could i do?)
so my ipod froze then, and i had the apple icon the whole time on the screen, so i tried everything, i get so frustrated with the ipod that i just want to throw it out the window. i read some things about the problem on the suppoort page, i reset it about a hundred times.. and finally it started working when i got it into disc mode. Yes i got all happy.. I press the restore buttons in itunes.. and this is what happens.. the ( i dont know how to call it) scroll bar? well the green bar that moves to show that its 'restoring' it freezes in the middle of the process, i uninstalled itunes 10 times.. i even tried restoring on 2 other computers, on one of them it does the same thing and on the other theres some other problem.
PLEASE HELP ME!! I DONT know what to do.
ipod 5th gen 30gb Windows XP

____________________16.06V16, Bus Type ATA, Bus Address [0,0]
USBSTOR\DiskApple__iPod___________1.62, Bus Type USB
Universal Serial Bus Controllers:
Otwarty kontroler hosta PCI do USB SiS 7001, Magistrala PCI 0, urządzenie 2, funkcja 2. Device is working properly.
No IEEE 1394 Host Controller found.
The last connected iPod serial number: ****.
The iPod Service Logging Information:
[SERVICE: 0xB20,22:06:21 INFO] Started C:\Program Files\iPod\bin\iPodService.exe (Mon Nov 20 22:06:21 2006)
[SERVICE: 0xB20,22:06:21 INFO] ##### iPodService starting as a service, version: 7.0.2.16
[SERVICE: 0xB2C,22:06:22 INFO] Timed out... Starting device manager!
[SERVICE: 0xB54,22:06:22 INFO] Listener Window created
[SERVICE: 0xB54,22:07:32 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:07:32 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:07:32 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:07:34 INFO] [InterfaceArrival] \\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
[SERVICE: 0xB54,22:07:34 INFO] device \\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
[SERVICE: 0xB54,22:07:34 INFO] device is an iPod
[SERVICE: 0xB54,22:07:34 INFO] type 0x7 drive 0x1 partition 0x0
[SERVICE: 0xB54,22:07:34 INFO] [-1] set waiting to mount = 1
[SERVICE: 0xB54,22:07:34 INFO] [1] Assigning session 0
[SERVICE: 0xB54,22:07:34 INFO] [1] added device interface "\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}" to m_objDeviceNameMap
[SERVICE: 0xB54,22:07:34 INFO] [1] added state machine 1 to m_objDeviceIdMap
[SERVICE: 0xB54,22:07:34 INFO] [1] added device number 1 to m_objDeviceNumberMap
[SERVICE: 0xB54,22:07:34 INFO] [1] added device interface "\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}" to m_vctDeviceInterfaces
[SERVICE: 0xB54,22:07:34 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:07:34 INFO] [1] input #0 from src #0
[SERVICE: 0xB44,22:07:34 INFO] [1] input #0
[SERVICE: 0xB44,22:07:34 INFO] [MACHINE 1 INPUT #0] - (HDW) CheckDevNode
[SERVICE: 0xB44,22:07:34 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB54,22:07:38 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:07:38 INFO] [1] input #1 from src #0
[SERVICE: 0xB48,22:07:38 INFO] [1] input #1
[SERVICE: 0xB48,22:07:38 INFO] [MACHINE 1 INPUT #1] - (HDW) CheckDevNode
[SERVICE: 0xB48,22:07:38 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB54,22:07:39 INFO] [SIMULATED VOLUME ARRIVAL] generating volume mount for \\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
[SERVICE: 0xB54,22:07:39 INFO] [VolumeArrive] mask = 0x7D
[SERVICE: 0xB54,22:07:39 INFO] looking up device # for \\.\G:
[SERVICE: 0xB54,22:07:39 INFO] type 0x7 drive 0x1 partition 0x1
[SERVICE: 0xB54,22:07:39 INFO] iTunes device #1 found with drive letter G, mask 0x40
[SERVICE: 0xB54,22:07:39 INFO] [1] set waiting to mount = 0
[SERVICE: 0xB54,22:07:39 INFO] looking up device # for \\.\F:
[SERVICE: 0xB54,22:07:39 INFO] type 0x2 drive 0x1 partition 0xffffffff
[SERVICE: 0xB54,22:07:39 INFO] looking up device # for \\.\E:
[SERVICE: 0xB54,22:07:39 INFO] type 0x2 drive 0x0 partition 0xffffffff
[SERVICE: 0xB54,22:07:39 INFO] [SIMULATED INTERFACE ARRIVAL] generating connect event for device 0
[SERVICE: 0xB54,22:07:39 INFO] looking up device # for \\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
[SERVICE: 0xB54,22:07:39 INFO] type 0x7 drive 0x1 partition 0x0
[SERVICE: 0xB54,22:07:39 INFO] looking up device # for \\.\D:
[SERVICE: 0xB54,22:07:39 INFO] type 0x7 drive 0x0 partition 0x2
[SERVICE: 0xB54,22:07:39 INFO] [SIMULATED INTERFACE ARRIVAL] generating connect event for device 0
[SERVICE: 0xB54,22:07:39 INFO] looking up device # for \\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
[SERVICE: 0xB54,22:07:39 INFO] type 0x7 drive 0x1 partition 0x0
[SERVICE: 0xB54,22:07:47 INFO] [VolumeArrive] mask = 0x40
[SERVICE: 0xB54,22:07:47 INFO] looking up device # for \\.\G:
[SERVICE: 0xB54,22:07:47 INFO] type 0x7 drive 0x1 partition 0x1
[SERVICE: 0xB54,22:07:47 INFO] iTunes device #1 found with drive letter G, mask 0x40
[SERVICE: 0xB54,22:07:47 INFO] [1] set waiting to mount = 0
[SERVICE: 0xB54,22:07:47 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:07:47 INFO] [1] input #2 from src #0
[SERVICE: 0xB4C,22:07:47 INFO] [1] input #2
[SERVICE: 0xB4C,22:07:47 INFO] [MACHINE 1 INPUT #2] - (HDW) CheckDevNode
[SERVICE: 0xB4C,22:07:47 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB50,22:07:51 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB50,22:07:51 INFO] [First Connect] Creating connect event for device 1
[SERVICE: 0xB50,22:07:51 INFO] [1] set waiting to mount = 1
[SERVICE: 0xB50,22:07:51 INFO] [1] input #3 from src #0
[SERVICE: 0xB44,22:07:51 INFO] [1] input #3
[SERVICE: 0xB44,22:07:51 INFO] [MACHINE 1 INPUT #3] - (HDW) Interface Arrival
[SERVICE: 0xB44,22:07:51 INFO] [1] progress state is 2, Waiting to mount = 1
[SERVICE: 0xB44,22:07:51 INFO] [1] progress is now 2
[SERVICE: 0xB44,22:07:51 INFO] [1] progress is now 2
[SERVICE: 0xB44,22:07:51 INFO] [MACHINE 1 TRANSITION] - {Unknown} ==> {Connected}
[SERVICE: 0xB44,22:07:51 INFO] [MACHINE 1 ACTIONS] - {Connected}
[SERVICE: 0xB44,22:07:51 INFO] [1] SCSI Inquiry attempt #0
[SERVICE: 0xB50,22:07:52 INFO] [First Connect] Creating mount event for device 1
[SERVICE: 0xB50,22:07:52 INFO] [VolumeArrive] mask = 0x7D
[SERVICE: 0xB50,22:07:52 INFO] looking up device # for \\.\G:
[SERVICE: 0xB50,22:07:52 INFO] type 0x7 drive 0x1 partition 0x1
[SERVICE: 0xB50,22:07:52 INFO] iTunes device #1 found with drive letter G, mask 0x40
[SERVICE: 0xB50,22:07:52 INFO] [1] set waiting to mount = 0
[SERVICE: 0xB50,22:07:52 INFO] [1] input #4 from src #0
[SERVICE: 0xB50,22:07:52 INFO] looking up device # for \\.\F:
[SERVICE: 0xB50,22:07:52 INFO] type 0x2 drive 0x1 partition 0xffffffff
[SERVICE: 0xB50,22:07:52 INFO] looking up device # for \\.\E:
[SERVICE: 0xB50,22:07:52 INFO] type 0x2 drive 0x0 partition 0xffffffff
[SERVICE: 0xB50,22:07:52 INFO] [SIMULATED INTERFACE ARRIVAL] generating connect event for device 0
[SERVICE: 0xB50,22:07:52 INFO] looking up device # for \\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
[SERVICE: 0xB50,22:07:52 INFO] type 0x7 drive 0x1 partition 0x0
[SERVICE: 0xB50,22:07:52 INFO] looking up device # for \\.\D:
[SERVICE: 0xB50,22:07:52 INFO] type 0x7 drive 0x0 partition 0x2
[SERVICE: 0xB50,22:07:52 INFO] [SIMULATED INTERFACE ARRIVAL] generating connect event for device 0
[SERVICE: 0xB50,22:07:52 INFO] looking up device # for \\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}
[SERVICE: 0xB50,22:07:52 INFO] type 0x7 drive 0x1 partition 0x0
[SERVICE: 0xB44,22:07:53 INFO] VendorId: Apple
[SERVICE: 0xB44,22:07:53 INFO] ProductId: iPod
[SERVICE: 0xB44,22:07:53 INFO] revision: 1.62
[SERVICE: 0xB44,22:07:53 INFO] vendor bytes:
[SERVICE: 0xB44,22:07:53 INFO] 02 01 00 00 00 00 00 00 00 0B 00 11 91 00 00 00 00 00 00 00
[SERVICE: 0xB44,22:07:53 INFO] [1] firmware version: 1.62 (0x13E)
[SERVICE: 0xB44,22:07:53 INFO] [1] Power State: Powered
[SERVICE: 0xB44,22:07:53 INFO] [1] Checkpoint attempt #0
[SERVICE: 0xB44,22:08:01 ERROR] Did not find first letter of stage
[SERVICE: 0xB44,22:08:01 INFO] got HotPlugState 0
[SERVICE: 0xB44,22:08:01 INFO] [1] serial number 000A270015BEEE43
[SERVICE: 0xB44,22:08:01 INFO] [1] *** CONNECTED - Sending event out, device session 0.
[SERVICE: 0xB44,22:08:01 INFO] [1] input #4
[SERVICE: 0xB44,22:08:01 INFO] [MACHINE 1 INPUT #4] - (HDW) Volume Mount
[SERVICE: 0xB44,22:08:01 INFO] [MACHINE 1 TRANSITION] - {Connected} ==> {Mounted}
[SERVICE: 0xB44,22:08:01 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB44,22:08:01 INFO] [MACHINE 1 ACTIONS] - {Mounted}
[SERVICE: 0xB44,22:08:01 INFO] [1] progress state is 2, Waiting to mount = 0
[SERVICE: 0xB44,22:08:01 INFO] [1] progress state is 2, Waiting to mount = 0
[SERVICE: 0xB44,22:08:13 ERROR] Did not find first letter of stage
[SERVICE: 0xB44,22:08:13 INFO] got HotPlugState 0
[SERVICE: 0xB44,22:08:17 INFO] [1] GetVolumeInformation() failed with error 1005
[SERVICE: 0xB44,22:08:17 INFO] [1] ===== iPod with Video =====
[SERVICE: 0xB44,22:08:17 INFO] [1] progress state is 2, Waiting to mount = 0
[SERVICE: 0xB44,22:08:17 INFO] [1] iPod needs formatting...
[SERVICE: 0xB44,22:08:17 INFO] 22:8:17, year 2006, day of yr. 323, GMT offset 4 isDST 0
[SERVICE: 0xB44,22:08:17 INFO] [1] Perform launch updater check.
[SERVICE: 0xB44,22:08:17 INFO] [1] iTunes located at 'D:\iTunes.exe'
[SERVICE: 0xB44,22:08:17 INFO] [1] progress is now 0
[SERVICE: 0xB44,22:08:17 INFO] [1] *** MOUNT FAILED - Non-FAT32 device, device session 0
[SERVICE: 0xB34,22:08:57 INFO] <0x4> Got Serial #
[SERVICE: 0xBD0,22:09:01 INFO] [1] GetVolumeInformation() failed with error 1005
[SERVICE: 0xBD0,22:09:01 INFO] <0x4> GetFormatType() returned unknown format 4
[SERVICE: 0xBD0,22:09:01 INFO] [1] Progress state is 0, Waiting to disconnect = 0
[SERVICE: 0xD04,22:09:01 INFO] Mounted
[SERVICE: 0xD04,22:09:01 INFO] [1] already mounted!
[SERVICE: 0xD04,22:09:01 INFO] [1] progress state is 0, Waiting to mount = 0
[SERVICE: 0xB34,22:09:03 ERROR] ERROR, mount lock count is 0 but device is not mounted
[SERVICE: 0xBD0,22:09:07 INFO] [1] GetVolumeInformation() failed with error 1005
[SERVICE: 0xBD0,22:09:07 INFO] <0x4> GetFormatType() returned unknown format 4
[SERVICE: 0xBD0,22:09:16 INFO] <0x1> Got Serial #
[SERVICE: 0xB34,22:09:16 INFO] <0x1> Got Serial #
[SERVICE: 0xB34,22:09:20 INFO] [1] GetVolumeInformation() failed with error 1005
[SERVICE: 0xB34,22:09:20 INFO] <0x1> GetFormatType() returned unknown format 4
[SERVICE: 0xBD0,22:09:22 INFO] <0x1> Got Serial #
[SERVICE: 0xBD0,22:09:22 INFO] API is now LOCKED!!!
[SERVICE: 0xB54,22:11:15 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:11:15 INFO] [1] input #5 from src #0
[SERVICE: 0xB48,22:11:15 INFO] [1] input #5
[SERVICE: 0xB48,22:11:15 INFO] [MACHINE 1 INPUT #5] - (HDW) CheckDevNode
[SERVICE: 0xB48,22:11:15 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB54,22:12:22 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:12:22 INFO] [1] input #6 from src #0
[SERVICE: 0xB4C,22:12:22 INFO] [1] input #6
[SERVICE: 0xB54,22:12:22 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:12:22 INFO] [1] input #7 from src #0
[SERVICE: 0xB44,22:12:22 INFO] [1] input #7
[SERVICE: 0xB4C,22:12:22 INFO] [MACHINE 1 INPUT #6] - (HDW) CheckDevNode
[SERVICE: 0xB4C,22:12:22 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB44,22:12:22 INFO] [MACHINE 1 INPUT #7] - (HDW) CheckDevNode
[SERVICE: 0xB44,22:12:22 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB54,22:18:13 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:18:13 INFO] [1] input #8 from src #0
[SERVICE: 0xB48,22:18:13 INFO] [1] input #8
[SERVICE: 0xB48,22:18:13 INFO] [MACHINE 1 INPUT #8] - (HDW) CheckDevNode
[SERVICE: 0xB48,22:18:14 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB54,22:21:48 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:21:48 INFO] [1] input #9 from src #0
[SERVICE: 0xB4C,22:21:48 INFO] [1] input #9
[SERVICE: 0xB54,22:21:48 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:21:48 INFO] [1] input #10 from src #0
[SERVICE: 0xB44,22:21:48 INFO] [1] input #10
[SERVICE: 0xB4C,22:21:48 INFO] [MACHINE 1 INPUT #9] - (HDW) CheckDevNode
[SERVICE: 0xB4C,22:21:48 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB44,22:21:48 INFO] [MACHINE 1 INPUT #10] - (HDW) CheckDevNode
[SERVICE: 0xB44,22:21:48 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB54,22:44:23 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:44:23 INFO] [1] input #11 from src #0
[SERVICE: 0xB48,22:44:23 INFO] [1] input #11
[SERVICE: 0xB48,22:44:24 INFO] [MACHINE 1 INPUT #11] - (HDW) CheckDevNode
[SERVICE: 0xB48,22:44:24 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB54,22:52:27 INFO] [VolumeRemoved] existing mask 0x40, arrive mask 0x20
[SERVICE: 0xB54,22:52:47 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:52:47 INFO] [1] input #12 from src #0
[SERVICE: 0xB4C,22:52:47 INFO] [1] input #12
[SERVICE: 0xB54,22:52:47 INFO] [DevNodesChanged]
[SERVICE: 0xB54,22:52:47 INFO] [1] input #13 from src #0
[SERVICE: 0xB44,22:52:47 INFO] [1] input #13
[SERVICE: 0xB4C,22:52:47 INFO] [MACHINE 1 INPUT #12] - (HDW) CheckDevNode
[SERVICE: 0xB4C,22:52:48 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB44,22:52:48 INFO] [MACHINE 1 INPUT #13] - (HDW) CheckDevNode
[SERVICE: 0xB44,22:52:48 INFO] Connection Detection Status - 0x180600A, device '\\?\usbstor#disk&venapple∏_ipod&rev1.62#000a270015beee43&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
[SERVICE: 0xB54,22:52:49 INFO] [VolumeArrive] mask = 0x20
[SERVICE: 0xB54,22:52:49 INFO] looking up device # for \\.\F:
[SERVICE: 0xB54,22:52:49 INFO] type 0x2 drive 0x1 partition 0xffffffff
Windows XP
well i clicked help.. and that didnt do anything either.. ;/

Bootcamp Windows battery life - USB power problem?

Hi,
While the battery life on my MBP is ok under Windows (3 hours), it's not great when compared to booting into OSX where I get at least 30% more. It's easy (and right) to blame Windows inefficiencies when running XP or Vista, MS have massively improved energy performance under Windows 7. Looking into this a bit, I've found there is now a new tool to help investigate energy problems:
POWERCFG /ENERGY
The generated power report shows that I have five cases of "USB Device not Entering Suspend". In otherwords (even though I don't have any devices plugged in) the USB components are burning at full power and not allowing Windows to suspend them to save energy. This may well explain why I'm not getting the battery life I could be, and it's really not Windows fault.
Does anyone else see this? I'm on MBP5.5 w/ Win7 Pro x64.
Hopefully a future Bootcamp will enable full power management support..
Cheers,
Chris.

Hello,
the core of the problem is the quality of the Boot Camp drivers.
The boot camp drivers allow very limited power management, therefore there is no real possibility to run Vista or WindowsXP without heavily using battery resources.
I don't think there will be any improvements in the future as Apple in not really committed to deliver better drivers (the present BootCamp power management drivers have remained virtually unchanged since BootCamp 1.2 beta, March 2007).
Just have a look at the threads about BootCamp especially about the problems that are plaguing the new MacBook Pro (mid 2009) i.e. poor sound quality and no microphone in Windows.
Cheers
Luca

PLEASE HELP - COLOR SHIFTING PROBLEM on output NTSC monitors

http://www.smmlv.com/testproject/
Above is a link to a layered photoshop file that has a USA map and over a dozen network overlays used in a section of our video. I animate each layer on sepeartely in the video and have noticed a major problem recently, the color of the art does not hold true to placement. I created the art originally in Illustrator and then converted the file to Photoshop at 640x480, 72dpi. This has always worked perfectly in the past to display and animated artwork in FCP.
Right now, in FCP I am using the NTSC DV 3:2 frame size, and the compressor of DV/DVCPRO - NTSC. I have a JVC Profressional DV deck that hooks up through firewire and sends S-Video to my monitors. This setup has always given me a great picture even though it is not completely upcompressed. Using these settings and this art, the color lines on this map in red, light blue, yellow and purple all have a "color shift" to the left about 5 pixels. It makes it appear that the line is where it is in the file, but the color overlaying the line is offset to the left 5 pixels and transperant to about 50%. This occurs only when viewed on some TV's and NTSC monitors and projectors. The strange thing is, some monitors display the color aligned almost perfectly on these maps and other monitors and projectors show this "digital halo" of color shifting really bad. If I take the layered network overlays in these colors and color tint them to black or grey, white, light green, or even light orange, they no longer have the color shifting and the detail is perfect.
Is there any way to fix this problem? I have tried duplicating the sequence and setting the compressor to 8bit Uncompressed, and while my captured footage is not this compression, in theory the art should render at this higher resolution setting. This did nothing to solve the problem.
I also have tried using different Broadcast safe and Y/C corrector filters with different results. The Y/C filter allowed me to reposition the color problem and thus removing most of the problem, but also removing most of the color. Nothing else has allowed me to seemingly move the color into the proper possition.
What is causing this color shift on the displayed NTSC image?
In FCP 4.5 I can see my rendered video in the program viewer screen and besides the pixel compression appearing on the lines, overall the video looks great paused or even better when playing. Then you view it through my deck onto my Pro Sony NTSC 19" color monitor and it also appears great, with a slight color halo to the left of these colors, but the color in the lines are there. If you are a few feet from the screen and know what you are looking for you might see it, but doubtful. Then you view it using the same signal on a 17" Samsung TV and the color shifting makes the map and other art, like the clients blue logo, look horrible, with each color line appearing twice and offset left from each other as if you had double vision. Normally I would think it is the TV causing this, but then we tested this same movie on 2 differnt projectors. The $700 Epson projector displayed everything beautifully, again with only the slightest color halo to the left, but then the Panasonic $4000 projector made everthing in these colors look double vision again. What is going on???
One more thing to keep in mind, my color bars also show this problem with these colors as well as shot footage of these facilities. There are tall red poles in the shots and everything displays fine except for the red pole color looks like it's glowing off the pole to the left.
PLEASE tell me there is a solution to this.

I have tried Degaussing, using filters, changing cables, and testing other monitors and systems on these monitors, everthing I can think of to solve the issue. Is it FCPo or is it the monitors?... or is it a signal strength thing. Can monitors and projectors shift color when the signal is read from a DVD or Mini DV Deck? Is there a fequency difference (Ie: 75mgz or 80 mgz) that might be causing the shift in some monitors and not so badly in others. But if this was true, how would some DVD's (like Baby Einstein DVDs that use really bright colors) display red and blue perfect using these same player and monitor, while my projects is shifting color? Doesn't that rule out the signal from the DVD player if other DVD's do not have this issue?
I have uploaded the original art used, an exported .jpg file from the FCP timeline and sample photos of 2 different monitors to show to show this problem as best I can. http://www.smmlv.com/testproject/
Someone out there must have had this problem before. There's no way a color shift problem like this with Mini DV has gone on this long without someone seeing it.
One last thing about what I have tried... I do understand that with editing in Mini DV instead of uncompressed or HD video I lose a bit of resolution (4:2:2) and I see this compression occuring in some of the areas in the video where these problems persist. But, I did remake the art and rerender this project in an 8bit uncompressed settings and then displayed that up on the screen and I get the same color shift. I keep going in circles trying to find the culprit that is causing the delema.
PLEASE HELP! There are large tours going through our facilities daily and the large screen projector is displaying this problem as well. Let's just hope they don't notice and that their TV's at home or office does not display it on our final DVD's made.

I have just started using WD external hard drives, I use it to save my movies and music on. On more than one occasion, when I connect to my MacBook it erases everything on had on there. Can someone please help with this problem?

I have just started using WD external hard drives, I use it to save my movies and music on. On more than one occasion, when I connect it to my MacBook it erases everything I had save on the hard drive. Can someone please help me with this problem? I am super tired of having to put all of my movies and music on the hard drive just to have it erased again. The products I am using are WD 4TB My Book and 2 TB My Passport external hard drives. When it happens, there is always an icon that reads, EFI, along with the My Book icon. Thank you for your assisstance.

dwgar1322 wrote:
I have just started using WD external hard drives, I use it to save my movies and music on. On more than one occasion, when I connect it to my MacBook it erases everything I had save on the hard drive. Can someone please help me with this problem? I am super tired of having to put all of my movies and music on the hard drive just to have it erased again. The products I am using are WD 4TB My Book and 2 TB My Passport external hard drives. When it happens, there is always an icon that reads, EFI, along with the My Book icon. Thank you for your assisstance.
Yes, you have WD software installed REMOVE IT !!
WD has warned its customers about their huge mistake that their software doesnt work on Mavericks and causes data loss.
(also dont use WD drives anymore)
Read all about it here:
https://discussions.apple.com/thread/5475136?start=255&tstart=0
See their website on removing the destructive WD software here:
http://community.wd.com/t5/External-Drives-for-Mac/External-Drives-for-Mac-Exper iencing-Data-Loss-with-Maverick-OS/td-p/613775
Western Digital External Hard Drives Experiencing Data Loss On OS X Mavericks
http://www.cultofmac.com/252826/western-digital-external-hard-drives-experiencin g-data-loss-on-os-x-mavericks/

Please help, color printing problems.

I have snow leopard and just bought a new HP officejet 7500 wide format wireless all-in-one. The problem is when I Print from my boyfriend's PC, the pictures are fine but when I print from my imac, the image I see on the monitor isn't what is printed. The colors are off and the picture is way too dark. I've looked on the internet to try to find a solution but haven't really found one. Please help.

Hello
Driver from HP web site
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=mp-86352-1 &cc=us&dlc=en&lc=en&os=219&product=4083652&sw_lang=
instruction for configurationn and use
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01846935&tmp_task=setupCate gory&cc=us&dlc=en&lc=en&os=219&product=4083652&softwareitem=mp-86352-1&sw_lang=# N28
HP printer listing for os 10.6 support is not that clear but "HP Officejet Pro L7500 series" in on the list so you may not need to download driver from hp but only from apple
HTH
Pierre

Very frastrated. Please HELP! SX712 problem copying music from latptop to IC recorder

It worked before. I haven't used it for a while. Now, I wasted hours to try to solve this problem to no avail.
When I connected my SX712 IC Recorder to my laptop, I could see 3 folders: MUSIC, PODCAST and VOICE and one file: capability_01.
I copied a bunch of MP4 files to the MUSIC folder and then disconnected the IC Recorder from the laptop.
On the IC Recorder, I pressed the "folder" button. Only MUSIC and BOOKS were shown next to the Conversation icon. The Conversation icon was the only icon showing on the left panel. There was no MUSIC or PODCAST icons or any of the files that I copied over which were visible to me when the IC Recorder was connected to the laptop.
What did I do wrong?
Please HELP!
Many Thanks in advance...Mimi

Hi Mimi! The ICD-SX712 Digital Voice Recorder only supports MP3, WMA, AAC-LC and PCM files. MP4 files are not supported.
If my post answers your question, please mark it as "Accept as Solution"
http://bit.ly/Win-4K

PLEASE HELP : Major IPOD Problem

Please Help:
Recently I downloaded the new Itunes(Itunes 7). After downloading it I was prompted to upgrade my Ipod (30g Video) to the new system (1.2). Almost immediatly after finishing this download my Ipod turned off, and is now frozen and will not turn on. Also, my computer doesn't recognize when my Ipod is plugged in, nor does the "Do not disconnect" screen come up, my Ipod stays blank. I called Apple they told me that I can send in my Ipod for it to be fixed, but the hard drive on the Ipod will be wiped. I recently bought a new computer and do not have any of my songs in my library, this is over 2000 (2000 + dollars) songs I have bought that I am currently on the verge of losing.
I have tried various USB ports, two different computers, restarting my Ipod, talking to apple technichal support, putting my Ipod into disk mode, manually trying to get the compter to recognize the Ipod through the manager, and smashing on my desk out of anger hoping that something might happen (just kdding). I believe thats everything, any other ideas you have are greatly appreciated.
If anybody has any ideas on how can get my computer to recognize the Ipod is plugged in so I can back up all the songs (via my computer, ipod...copy all music files) would be greatly appreciated, that way when I send in my Ipod and then get it back, I can put my songs back on.
Thank you in advance!
Windows Windows XP

one thing that you can try is something my dad taught me. This works great especiall if you have a PC.
When i had to replace my laptop and was worried about losing all of my purchased songs from itunes, i was told to plug the ipod into the computer BEFORE installing itunes. it will read on your computer as a mass storage device and then all you need to do is simply go into the folders and copy all of the files into your "my music" folder (or whatever folder you choose). After that, you need to install/reinstall itunes and when it searches your computer for music, ALL of your music (including purchased songs) will show up and all will be okay.
Just a few hints;
although this seems very simple, if you're a simple person like i am, you'll expect to see the songs on your ipod show up with normal/regular titles.....THEY WONT. They'll show up as letter-number combinations, but the music is all there.
In short;
1. uninstall/delete itunes
2. Plug in our ipod (but don't reinstall itunes yet)
3. copy ALL of the files you can find on your ipod
4. reinstall itunes
5. let it search your computer for music
you should be fine at this point.
I hope this helps!

Please Help! Two problems with my iMac at once a week b/4 finals!!!!

First I'd just like to mention that I have no idea which OS X I have so...yeah, sorry. I was depending on this computer to work for my class finals. Anyway, on with the problems.
My school is getting all new computers next year, so they are selling all of their iMacs for ten dollars each. Like an idiot, I bought one. And...so did my brother. But anyway, I got it home and started it up and all that came up was the traditional BIIINNNNGGGG, a white screen(for a second), then a gray one. This little icon comes up in the middle that you can't click on(the cursor doesn't come up)but it's purple and has a little cartoon face on it. This icon only comes up if you are not pressing any keys or click/moving the mouse.
So I went back to school the next day and asked what was up, and they said that they completely wiped the computer and that I would have to buy new OS X install software. Okay...so I went to my computer teacher and he had a few sets of OS X install software.
I brought it home and turned on my computer. I put in the disk that said OS X Install and it went in. The computer whirred for a bit, then spit the disk back out. So I decided to try a different disk because I thought that maybe the computer already had the contents of that disk on it. I put in the Applications disk, and now it refuses to come out. I have tried plugging the keyboard into different ports(there are two, with two others on the keyboard itself for the mouse) and everything. I looked inside through the little slot(discs go right into the computer-no hard drive or disk tray that slides out) on the front and the disc is spinning but nothing is happening.
Please help me with both my wiped computer problem and my stuck disc problem. I have tried to give as much detail to help anyone who can help me. Please, WHAT CAN I DO?!
iMac Mac OS X (10.0.x) I have an OS X. No idea which one...
iMac Mac OS X (10.0.x) I have an OS X. No idea which one...
iMac Mac OS X (10.0.x) I have an OS X. No idea which one...

The full retail install disks are available here and at any Apple Store and many computer retailers. Also, check the system requirements. Be sure your Mac has firewire and enough ram to run Tiger. At this point you might be able to find the disks at a slightly discounted price because of the coming release of 10.5 Leopard. But be sure it is the black disk, boxed version if possible.
EDIT: And the install disc for Tiger is a DVD, so be sure your iMac has DVD.
This may help to narrow down the model iMac you have.
-mj
[email protected]
Message was edited by: macjack

Please help with AcroIEHelper problem

Hello,
I had perfectly running laptop. Now, with no reason every time I turn on my laptop I get a messege that Windows Installer is preparing to install something. Then Installer asks me to insert a disc with Adobe Acrobat 7.0 Pro. When I insert the disc installer tells me that it can not access a file. Exactly:
Adobe Acrobat 7.1.0 Professional
Error 1304: Error writing to file C:\Program Files\Adobe\Acrobat 7.0\ActiveX\AcroIEHelper.dll.
Verify that you have access to that directory.
I checked that directory and did not find such file. Sometimes, this messege appears when I try to open C: or folders on my Desktop but not always. Once it showed up when I tryed to start IE. Ater I uninstalled Adobe Acrobat this messege stopped showing up. But when I reinstalled Adobe Acrobat it started again.
I have tryed almost every anti-malware I could find - McAfee, Spybot, Spyware Doctor, Malwarebyte's Anti-Malware, Superantispyware, AVG 8.5, Dr. Web - all these programms I ran in both normal and safe modes. I even went to BIOS Setup and returned to factory settings. Nothing helped. I went to malware forum and people did not find any malware in my logs.
Then, I installed WinPatrol that seems to be able managing startup programs. After I desabled SC-Acrobat.exe and Adobe Gamma Loader I do not have this annoying Windows Installer for Adobe Acrobat warning any more when Windows starts. But it still shows up often, but not always when I open C: or folders on my Desktop. I have Windows Vista Home.
So could you please help me with this problem? Thank you.

MamaDragonBoy wrote:
It's already set to "mixed" wireless b and g... should I try setting it to all g? Both my laptop and my husband's are "g"
setting it to g certainly wont hurt anything.

Please help...Problem with 3D Applet using JRE 1.5

Hi all,
I have an applet which uses sun opengl 1.3.1 plugin to render some 3D graphics. It is working fine with JRE 1.4.2_06, but not showing the 3D graphics with the latest JRE 1.5 release. I tried to repaint using available API with no success.
Please help asap,
Thanks in advance
prasad

I wonder if you have the same problem as me... Maybe we can find a solution for us both, no need for me to open a new thread for this topic then...
I wrote an applet using Swing and compiled it using JavaSDK 1.4.x. I also installed the 1.4.x JRE for both of my test browsers. In Mozilla 1.1 the applet displays properly all the time. In IE6 SP1 it sometimes works as intended but sometimes the applet simply stops working, as per my Java Console somewhere after invoking the "start" method. Parts of the applet simply become gray and when I resize it - I have a JFrame in my applet - the whole JFrame becomes gray and does not respond to input nor it redraws itself. Shutting down IE does not close the JFrame(although the java console reports normal program termination and cleanup) and the only way to close it is through the task manager. I am using Windows 98SE btw.
Does it sound similiar to your problem? It happens ONLY with IE, not with Mozilla. Anybody has an idea on what it could be? I doubt there's an error in my code...

Please help! connection problems

ok I've been working on this for several hours now and can't figure it out. I just moved back home and my connection was working some yesterday but I can't get it to work anymore.
It says I'm connected but it won't receive any packets. I changed the SSID name and removed the old SSID's. I reinstalled my wireless pci card drivers and switched pci slots. I updated the router's firmware (it's WRT54G). I changed Advanced Wireless Settings as suggested: Beacon Interval: 50; lowered Fragmentation and RTS threshholds by 40 each. I switched the router to channel 11.
I've tried repairing the connection many times (some times it works, most times it won't renew IP address); I've also reset the router many times.
My computer skills are intermediate but certainly not advanced. I can't directly connect it to the modem via cable b/c I don't have the necessary hardware (modem card?). I talked to tech support and I was able to "ping yahoo.com," google, etc successfully but it just won't receive packets...Please help!

The best thing to do at this point is to go back over setting up the wireless security settings again and make sure that while you are setting up these settings that you connect an Ethernet cable from that computer to the router then perform a power cycle
You need to remove the power cable from the Linksys router, then remove the power cable from the modem, wait about 60 seconds, then plug in the modem, then plug in the Linksys router. Wait about 3 minutes while the modem and router sync back up. Once all light are back on,disconnect the ethernet cable and now try to connect.
Here are instructions to follow if you need them
Setting up your wireless connection in your router.
*** Step #5 = you can choose the type of encryption that fits your set-up, the example I give is: WPA/TKIP+AES
***Also Pay close attention to the security and security key information and make sure it matches. (What is entered in the router must be entered in the computer.
1.Open Internet Explorer and type 192.168.1.1 into the address bar.
2.You will now get a sign-in box, User Name = (Leave Blank)
                                                       Password = admin (all lower case letters)
3.Once the set-up page opens, click on the Wireless Tab as youwill need to change the settings. A) Wireless Network Mode = Mixed
              B) Wireless Network Name (SSID) = Choose any name and do not use Linksys.
              C) Wireless Channel = 1, 6 or 11 is best, so see which work best for you.
              D) Wireless SSID Broadcast = Enabled.
4. Now go to the bottom of the page and click on save settings.
5. Click on the Wireless Security Sub tab.
              A) Security Mode: WPA
              B) WPA Algorithms: TKIP + AES
              C) WPA Shared Key: Type 24 letters, and numbers using lower and upper case letters
              D) Group Key Renewal: 3600
6. Once again go to the bottom of the page and click on Save Settings.
7. Now you can close out of this page.
8. You will now need to enter the security info into your computer. I will now give you 2 links, depending which operating system you have, Vista or XP you will follow the one you have.
Vista = http://www.home-network-help.com/wireless-adapter-configuration-in-vista.html
XP = http://www.home-network-help.com/wireless-adapter.html
Now try to make a wireless connection.
Good Luck,
Ttech

Please help!! - usb power problems

Similar Messages

Maybe you are looking for