Plese Help, router configuration
I need help because my wireless function is not working. I remember once before i had assistance in an automatic reconfigure program for linksys, but i forgot how to get to it online. Help Please
Message Edited by seshun on 11-23-200611:53 AM
hi , here is where u can find the automatic configuration tool ... www.linksysfix.com and then select "easy link connect"
Similar Messages
-
Need urgent help in configuring Client to Site IPSec VPN with Hairpinning on Cisco ASA5510 - 8.2(1).
The following is the Layout:
There are two Leased Lines for Internet access - 1.1.1.1 & 2.2.2.2, the latter being the Standard Default route, the former one is for backup.
I have been able to configure Client to Site IPSec VPN
1) With access from Outside to only the Internal Network (172.16.0.0/24) behind the asa
2) With Split tunnel with simultaneous assess to internal LAN and Outside Internet.
But I have not been able to make tradiotional Hairpinng model work in this scenario.
I followed every possible sugestions made in this regard in many Discussion Topics but still no luck. Can someone please help me out here???
Following is the Running-Conf with Normal Client to Site IPSec VPN configured with No internat Access:
LIMITATION: Can't Boot into any other ios image for some unavoidable reason, must use 8.2(1)
running-conf --- Working normal Client to Site VPN without internet access/split tunnel
ASA Version 8.2(1)
hostname ciscoasa
domain-name cisco.campus.com
enable password xxxxxxxxxxxxxx encrypted
passwd xxxxxxxxxxxxxx encrypted
names
interface GigabitEthernet0/0
nameif internet1-outside
security-level 0
ip address 1.1.1.1 255.255.255.240
interface GigabitEthernet0/1
nameif internet2-outside
security-level 0
ip address 2.2.2.2 255.255.255.224
interface GigabitEthernet0/2
nameif dmz-interface
security-level 0
ip address 10.0.1.1 255.255.255.0
interface GigabitEthernet0/3
nameif campus-lan
security-level 0
ip address 172.16.0.1 255.255.0.0
interface Management0/0
nameif CSC-MGMT
security-level 100
ip address 10.0.0.4 255.255.255.0
boot system disk0:/asa821-k8.bin
boot system disk0:/asa843-k8.bin
ftp mode passive
dns server-group DefaultDNS
domain-name cisco.campus.com
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group network cmps-lan
object-group network csc-ip
object-group network www-inside
object-group network www-outside
object-group service tcp-80
object-group service udp-53
object-group service https
object-group service pop3
object-group service smtp
object-group service tcp80
object-group service http-s
object-group service pop3-110
object-group service smtp25
object-group service udp53
object-group service ssh
object-group service tcp-port
object-group service udp-port
object-group service ftp
object-group service ftp-data
object-group network csc1-ip
object-group service all-tcp-udp
access-list INTERNET1-IN extended permit ip host 1.2.2.2 host 2.2.2.3
access-list CSC-OUT extended permit ip host 10.0.0.5 any
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq www
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq https
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq ssh
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq ftp
access-list CAMPUS-LAN extended permit udp 172.16.0.0 255.255.0.0 any eq domain
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq smtp
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq pop3
access-list CAMPUS-LAN extended permit ip any any
access-list csc-acl remark scan web and mail traffic
access-list csc-acl extended permit tcp any any eq smtp
access-list csc-acl extended permit tcp any any eq pop3
access-list csc-acl remark scan web and mail traffic
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq 993
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq imap4
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq 465
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq www
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq https
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq smtp
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq pop3
access-list INTERNET2-IN extended permit ip any host 1.1.1.2
access-list nonat extended permit ip 172.16.0.0 255.255.0.0 172.16.0.0 255.255.0.0
access-list DNS-inspect extended permit tcp any any eq domain
access-list DNS-inspect extended permit udp any any eq domain
access-list capin extended permit ip host 172.16.1.234 any
access-list capin extended permit ip host 172.16.1.52 any
access-list capin extended permit ip any host 172.16.1.52
access-list capin extended permit ip host 172.16.0.82 host 172.16.0.61
access-list capin extended permit ip host 172.16.0.61 host 172.16.0.82
access-list capout extended permit ip host 2.2.2.2 any
access-list capout extended permit ip any host 2.2.2.2
access-list campus-lan_nat0_outbound extended permit ip 172.16.0.0 255.255.0.0 192.168.150.0 255.255.255.0
pager lines 24
logging enable
logging buffered debugging
logging asdm informational
mtu internet1-outside 1500
mtu internet2-outside 1500
mtu dmz-interface 1500
mtu campus-lan 1500
mtu CSC-MGMT 1500
ip local pool vpnpool1 192.168.150.2-192.168.150.250 mask 255.255.255.0
ip verify reverse-path interface internet2-outside
ip verify reverse-path interface dmz-interface
ip verify reverse-path interface campus-lan
ip verify reverse-path interface CSC-MGMT
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-621.bin
no asdm history enable
arp timeout 14400
global (internet1-outside) 1 interface
global (internet2-outside) 1 interface
nat (campus-lan) 0 access-list campus-lan_nat0_outbound
nat (campus-lan) 1 0.0.0.0 0.0.0.0
nat (CSC-MGMT) 1 10.0.0.5 255.255.255.255
static (CSC-MGMT,internet2-outside) 2.2.2.3 10.0.0.5 netmask 255.255.255.255
access-group INTERNET2-IN in interface internet1-outside
access-group INTERNET1-IN in interface internet2-outside
access-group CAMPUS-LAN in interface campus-lan
access-group CSC-OUT in interface CSC-MGMT
route internet2-outside 0.0.0.0 0.0.0.0 2.2.2.5 1
route internet1-outside 0.0.0.0 0.0.0.0 1.1.1.5 2
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
aaa authentication enable console LOCAL
http server enable
http 10.0.0.2 255.255.255.255 CSC-MGMT
http 10.0.0.8 255.255.255.255 CSC-MGMT
http 1.2.2.2 255.255.255.255 internet2-outside
http 1.2.2.2 255.255.255.255 internet1-outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map internet2-outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map internet2-outside_map interface internet2-outside
crypto ca trustpoint _SmartCallHome_ServerCA
crl configure
crypto ca certificate chain _SmartCallHome_ServerCA
certificate ca xyzxyzxyzyxzxyzxyzxyzxxyzyxzyxzy
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as
quit
crypto isakmp enable internet2-outside
crypto isakmp policy 10
authentication pre-share
encryption aes
hash md5
group 2
lifetime 86400
telnet 10.0.0.2 255.255.255.255 CSC-MGMT
telnet 10.0.0.8 255.255.255.255 CSC-MGMT
telnet timeout 5
ssh 1.2.3.3 255.255.255.240 internet1-outside
ssh 1.2.2.2 255.255.255.255 internet1-outside
ssh 1.2.2.2 255.255.255.255 internet2-outside
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy VPN_TG_1 internal
group-policy VPN_TG_1 attributes
vpn-tunnel-protocol IPSec
username ssochelpdesk password xxxxxxxxxxxxxx encrypted privilege 15
username administrator password xxxxxxxxxxxxxx encrypted privilege 15
username vpnuser1 password xxxxxxxxxxxxxx encrypted privilege 0
username vpnuser1 attributes
vpn-group-policy VPN_TG_1
tunnel-group VPN_TG_1 type remote-access
tunnel-group VPN_TG_1 general-attributes
address-pool vpnpool1
default-group-policy VPN_TG_1
tunnel-group VPN_TG_1 ipsec-attributes
pre-shared-key *
class-map cmap-DNS
match access-list DNS-inspect
class-map csc-class
match access-list csc-acl
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class csc-class
csc fail-open
class cmap-DNS
inspect dns preset_dns_map
service-policy global_policy global
prompt hostname context
Cryptochecksum: y0y0y0y0y0y0y0y0y0y0y0y0y0y
: end
Neither Adding dynamic NAT for 192.168.150.0/24 on outside interface works, nor does the sysopt connection permit-vpn works
Please tell what needs to be done here, to hairpin all the traffic to internet comming from VPN Clients.
That is I need clients conected via VPN tunnel, when connected to internet, should have their IP's NAT'ted against the internet2-outside interface address 2.2.2.2, as it happens for the Campus Clients (172.16.0.0/16)
I'm not much conversant with everything involved in here, therefore please be elaborative in your replies. Please let me know if you need any more information regarding this setup to answer my query.
Thanks & Regards
maxsHi Jouni,
Thanks again for your help, got it working. Actually the problem was ASA needed some time after configuring to work properly ( ?????? ). I configured and tested several times within a short period, during the day and was not working initially, GUI packet tracer was showing some problems (IPSEC Spoof detected) and also there was this left out dns. Its working fine now.
But my problem is not solved fully here.
Does hairpinning model allow access to the campus LAN behind ASA also?. Coz the setup is working now as i needed, and I can access Internet with the NAT'ed ip address (outside-interface). So far so good. But now I cannot access the Campus LAN behind the asa.
Here the packet tracer output for the traffic:
packet-tracer output
asa# packet-tracer input internet2-outside tcp 192.168.150.1 56482 172.16.1.249 22
Phase: 1
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
MAC Access list
Phase: 2
Type: FLOW-LOOKUP
Subtype:
Result: ALLOW
Config:
Additional Information:
Found no matching flow, creating a new flow
Phase: 3
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 172.16.0.0 255.255.0.0 campus-lan
Phase: 4
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 192.168.150.1 255.255.255.255 internet2-outside
Phase: 5
Type: ACCESS-LIST
Subtype: log
Result: ALLOW
Config:
access-group internnet1-in in interface internet2-outside
access-list internnet1-in extended permit ip 192.168.150.0 255.255.255.0 any
Additional Information:
Phase: 6
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 7
Type: CP-PUNT
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 8
Type: VPN
Subtype: ipsec-tunnel-flow
Result: ALLOW
Config:
Additional Information:
Phase: 9
Type: NAT-EXEMPT
Subtype: rpf-check
Result: ALLOW
Config:
Additional Information:
Phase: 10
Type: NAT
Subtype:
Result: DROP
Config:
nat (internet2-outside) 1 192.168.150.0 255.255.255.0
match ip internet2-outside 192.168.150.0 255.255.255.0 campus-lan any
dynamic translation to pool 1 (No matching global)
translate_hits = 14, untranslate_hits = 0
Additional Information:
Result:
input-interface: internet2-outside
input-status: up
input-line-status: up
output-interface: internet2-outside
output-status: up
output-line-status: up
Action: drop
Drop-reason: (acl-drop) Flow is denied by configured rule
The problem here as you can see is the Rule for dynamic nat that I added to make hairpin work at first place
dynamic nat
asa(config)#nat (internet2-outside) 1 192.168.150.0 255.255.255.0
Is it possible to access both
1)LAN behind ASA
2)INTERNET via HAIRPINNING
simultaneously via a single tunnel-group?
If it can be done, how do I do it. What changes do I need to make here to get simultaneous access to my LAN also?
Thanks & Regards
Abhijit -
Well ... I just spent a wonderful hour and a half (not) bouncing around VZ technical support, etc. trying to get assistance regarding configuring my DSL router.* Between the low-quality Skype connection to India and my lack of success, I'm a little bummed out right now.
Could one of you perhaps help me? I'm trying to configure a single, wire-attached network node (port 4 of the router) so that it can only consume up to 320 Kbps of my 750 Kbps (7.5 Mbps) DSL bandwidth ... no matter what. This results from this node consuming virtually all of the circuit's bandwidth when streaming or during bulk file transfers.
I have tried to remedy the problem using priority with no discernible impact.
The Quality of Service (QoS) element called Traffic Shaping (Services | QoS | Traffic Shaping), described on Page 51 of the VZ DSL-2750B User Manual , appears to be the ideal solution to my problem. Repeated attempts at activating this QoS have all resulted in no throttling of bandwidth consumption.
My most recent attempt was to define the device on Port 4 as the DMZ host ... and then apply a new rule (320 TX, 320 RX) to this interface. Again, no joy.
Does anyone have any experience with this service on this router?
Am I chasing my tail trying to configure the router without validating that my circuit is not configured with "Fastpath (PSE) inactive"?
If the circuit configuration is a potential problem, which office should I ask for at VZ customer service?
Here is the information from the System page of the Router Control Panel:
Gateway ID: PX2M1BC000000
Software Version: 5.4.12.1.44
Release Date: Feb 19 2012
Platform: D-Link DSL-2750B
Board Tag:... Ntag-5_4_12_1_44
Compilation Flags:... LIC=/home/bat/bat/dlink_bcm96328_5_4_12_1/20120219_1343/conf/jpkg_bcm9636x_dlink.lic CONFIG_RG_PROD_IMG=y DIST=DLINK_DSL2750B
I'll note that the Router provides a notification that "RX QOS might not operate when Fastpath (PSE) is active" when I update the router configuration page concerning Traffic Shaping. Because Fastpath is not mentioned in the User Manual, I'm guessing that Fastpath (PSE) might be a configurable attribute of the circuit servicing my PoP, but I have no idea if this is the case.
I searched for relevant messages on this board ... without success. If this has already been addressed, please provide a link, and accept my apologies. (My Google-Fu tends to be weak.)The asterisk in the first post refers to the following summary of events:
10:40 - Attempt to solve my configuration question using VZ chat begins.
10:49 - VZ chat agent Danish refers me to phone support. (Chat ID number is 020813176471 if you're with VZ and are interested.)
10:50 - Call VZ phone support.
11:02 - Talk with Angel. Because she has not heard of, nor received training in, "traffic shaping," she says my question about configuring this VZ DSL modem must be addressed by "Premium Technical Support." She transfers me.
11:13 - Talk with Pamela. Premium Technical Support only responds to questions about 3d party products. Because my question concerns a VZ DSL modem, Basic Technical Support is responsible. She transfers me.
11:17 - Talk with Joe. He says either the vendor (D-Link) or premium technical support is required. Because I had already tried with D-Link (they referred me to Verizon, as this modem was built exclusively for VZ), I explained what I had already experienced, and described how I wanted "assistance configuring my VZ DSL modem, specifically a feature described on page 51 of the User Manual." He transfers me.
11:23 - The automated phone system asks for my 12-digit customer ID. I wasn't able to find it fast enough, and rolled through to Financial Services. Eventually Trig picked up, listened to my story, and transferred me to "Technical Support" providing the direct dial number, just in case (866.945.79xx).
11:32 - Entered the phone queue. Lots of hissing and clicks.
11:35 - Talk with Monika. (The voice clarity from this point onward was on the order of 1st-generation Skype. Between the horrible language problem -- Monika is in India don'cha know -- and the lousy line quality, this was the most frustrating.) No matter what I said, I couldn't convey the reason for my call. I asked to talk with a supervisor, which Monika related was not possible. She also related that she could not transfer me to an American POC or supervisor.
12:01 - Hung up the phone ... and started down the path that led to my post immediately above.
I was repeatedly queried about the account name and number throughout the process. Conveying this information was especially challenging during the Indian call segment. -
I have a PC and a need help to configure my external hard disk on my network. Thanks
I have a PC and a need help to configure my external hard disk on my network. Thanks
If you mean you wish to plug a USB drive into the Airport Extreme router (or TC not express) that is easy..
The disk must be formatted FAT32.. as if.. stay away from FAT .. or HFS+ ie Mac OS extended Journaled.
Format the disk on a Mac is best.. and even use GUID partition scheme not MBR.
The PC has no issue writing and reading files because this is a network drive.. The PC does not write to the drive.. it writes files to the Airport OS which writes and reads the disk and passes the info using standard windows SMB.. To the windows computer it will be a Windows NT server.. FAT32 setup.
If your setup is different.. to my hugely guessed assumptions.. give details.. always helps to have.. make and model.
Make and model of disk.. make and model of router.. how the setup will be done.. what windows OS you run.. etc etc.
As it stands your question could have nothing to do with apple at all.. other than you posted in a forum so I guess there is something apple in there somewhere. -
Visualizing SAP XI routing configuration across the system landscape
Hi Experts
Iam facing some challenges in visualizing SAP XI routing configuration across the system landscape (Development, Quality, Production). Basically routing is based on a field (technical target system). Depending on the environment we have different target systems (different Mainframe DB that represent the same target system) configured.
Any word/excel/ppt/pdf templates or any comments that could help visualizing routing would be highly appreciated.
Thanks! SantoshHi Santhosh,
If you are worrieed about how your Business Systems will change when you move from Dev to QA to PROD for the Configuration in your ID, then the answer is simple.
You can create transport target for your Business System and so when you migrate the ID objects from dev to Qa and so on, the business Systems will be automatically replaced.
Take a look at this blog,
/people/sap.india5/blog/2005/11/03/xi-software-logistics-1-sld-preparation
Regards,
Bhavesh -
Hello Gurus
I need help to configure SAP Router in my server, can somebody guide me the process how to configure it.
Details of my server
SAP Version - 640
Oracle - 10.2.0.2.0
O/S - Windows - 2003 Server/ SP1
Thanks & Regards
ShishirHi,
check Note 30289 - SAProuter documentation
document is attached to note.
regards,
kaushal -
Hi All,
I need help on Configuring the Site to Site VPN from Cisco 2811 to Websense Cloud for web Traffic redirect
2811 having C2800NM-ADVIPSERVICESK9-M
2811 router connects to the Internet SW then connects to the Internet router.
Note- For Authentication am using the Device ID & Pre share key. I am worried as all user traffic goes with PAT and not firing up my tunnel for port 80 traffic. Can you please suggest what can be the issue ?
Below is router config for VPN & NAT
crypto keyring ISR_Keyring
pre-shared-key hostname vpn.websense.net key 2c22524d554556442d222d565f545246
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp keepalive 10
crypto isakmp profile isa-profile
keyring ISR_Keyring
self-identity user-fqdn [email protected]
match identity user vpn-proxy.websense.net
crypto ipsec transform-set ESP-NULL-SHA esp-null esp-sha-hmac
crypto map GUEST_WEB_FILTER 10 ipsec-isakmp
set peer vpn.websense.net dynamic
set transform-set ESP-NULL-SHA
set isakmp-profile isa-profile
match address 101
interface FastEthernet0/1
description connected to Internet
ip address 216.222.208.101 255.255.255.128
ip access-group HVAC_Public in
ip nat outside
ip virtual-reassembly
duplex full
speed 100
no cdp enable
crypto map GUEST_WEB_FILTER
access-list 101 permit tcp 192.168.8.0 0.0.3.255 any eq www
access-list 103 deny ip 192.168.8.0 0.0.3.255 host 85.115.41.187 log
access-list 103 deny ip 192.168.8.0 0.0.3.255 host 85.115.41.181 log
access-list 103 deny ip 192.168.8.0 0.0.3.255 host 85.115.41.182 log
access-list 103 deny ip 192.168.8.0 0.0.3.255 86.111.216.0 0.0.1.255
access-list 103 deny ip 192.168.8.0 0.0.3.255 116.50.56.0 0.0.7.255
access-list 103 deny ip 192.168.8.0 0.0.3.255 86.111.220.0 0.0.3.255
access-list 103 deny ip 192.168.8.0 0.0.3.255 103.1.196.0 0.0.3.255
access-list 103 deny ip 192.168.8.0 0.0.3.255 177.39.96.0 0.0.3.255
access-list 103 deny ip 192.168.8.0 0.0.3.255 196.216.238.0 0.0.1.255
access-list 103 permit ip 192.168.8.0 0.0.3.255 any
ip nat pool mypool 216.222.208.101 216.222.208.101 netmask 255.255.255.128
ip nat inside source list 103 interface FastEthernet0/1 overload
ip nat inside source route-map nonat pool mypool overloadHow does Websense expect your source IPs in the tunnel? 192.168.8.0 0.0.3.255 or PAT'ed 216.222.208.101 ?
Check
show crypto isakmp sa
show crypto ipsec sa
show crypto session
You'd better remove the preshared key from your post. -
Why do my router configuration site look like this?
Why do my router configuration site look like this:
it may be corrupted... try downloading a new firmware for your linksys router using this site... http://linksys.com/downloads and choose the model and version of the router that your using... also try turning the firewalls off... that would help
♥ Registered TradeMark Since 1987 ♥ -
Configuring Airport Extreme by replacing and old router configuration?
I have seen now a You Tube video explaining the possibility to install Airport Extreme and configuring it by replacing with an old router configuration. This will be my case because I have now a 3Com wireless router but Im waiting for a new Airport Extreme. What I would like to know is how to do that and what connections needed. If I understand well the explanations from YouTube, Airport Extreme must be connected to the internet through the ADSL modem but at the same time the old router must be turned on. It this correct?
What manual is that? Is it one that is available on Apple's website? I'm going to do a search for it.
You won't believe what happened. I just came up to check my email, and the Airport Utility just opened by itself and said it had found my AXn (which it had before also when I tried to configure it like you said to do). I went through the screens again and clicked Update yet again (like I had before) and instead of blinking yellow, the **** thing is solid green. I think I have a ghost in my house!!!
Well, thank you for all of your help! Do you have any insight into my other question about the AEBSn giving out a solid signal to my MBP, but when I click on Safari, it says that I'm not connected to the internet? I'm wondering if when I was setting up the AEBSn, the internet connection went to my computer instead of the AEBSn. I know I'm not describing this right, but it's like when I got my new iMac and tried to plug in the ethernet from the cable modem, it wouldn't recognize my iMac, but if I plugged it into my MBP it would. I had to reset the cable modem and then plug it in. The signal must have bypassed the AEBSn at some point and gone straight to my iMac (it's hardwired via ethernet cord from back of the AEBSn). It was broadcasting the internet signal at one point after my wife got it set up the first time because I was able to surf wirelessly on my MBP in the basement.
Message was edited by: Bunky -
I put some programe in icloud but not my account how can i re enstole again in my iphone but in my account in apple plese help my
Please help me??????
-
Lots of Nano problems... Plese help me!
I HAVE A NEW NANO THAT DOSEN´T WORK. IT WORKS WHEN IT´S NOT CONNECTED TO MY COMPUTER BUT WHEN I CONNECT IT THE DISPLAY SHOWS "DO NOT DISCONNCT". BUT THATS NOT ALL, ITUNES DOSEN´T FIND IT WHEN I CONNECT IT AND MY INFO ON THE NANO SAYS I ONLY GOT 2,7GB LEFT BUT THERE´S NOTHING ON IT. I GET AN ERROR MESSAGE WHEN I REINSTALL ITUNES. IT SAYS THAT I HAVE TO RUN "CHKDSK". I HAVE TRIED EVERY STEP ON THE APPLE FAQ PAGES. PLESE HELP ME!
firstly you can check to see if you ahve the latest version of itunes. to disconnect your ipod, try safley removing the hardware. all ipods only have 1.7 because its some of it used by the apple ipod system iteself. apple didnt say 2gb for your music, they just said 2gb ipod lol
-
Can't access router configuration
I have a wireless router WRT54GC. It worked fine until I got a new linker. Now I can neither connect wirelessly from my laptop (although the laptop says the connection is fine). Nor can I access the router configuration; the URL for the configuration program has changed since the new linker was installed, and I can ping it successfully, but via browser does not connect. Hard to do much without getting to the router configuration.
When you are trying to setup page of your Router are you getting any kind of error message?
Try to Disable the Firewall and Antivirus on your Router and then check if you are able to access the setup page of your Router, If still not then you can Hardwired a different computer to the router and then try to login to the setup page of your router, if still doesn't work then you can unplug the power from the router, wait for 30sec and then replug the power to the linksys router and then check if you are able to access the setup page of your router.
If still you are unable to access the setup page of your Router then you can Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router... -
I have old G5 and It;s not switching on can you plese help me
Dear All
I have old G5 and It;s not switching on can you plese help me
regardsHi ...
Best to post your topic here > Older Hardware: Apple Support Communities -
HT201303 I forgot answer my security questions plese help me
i forgot answer my security questions plese help me
Click here for information. If the option to have the answers emailed to you isn't available or doesn't work(the email may take a few hours to arrive), contact the iTunes Store staff via the link in the 'Additional Information' section of that article.
Nobody on these boards can reset them for you.
(91141) -
HT201210 why registered my iphone 5 plese help me
plese help me my iphone is locke i want registered?
see this link for stolen iphones http://discussions.apple.com/thread/3978740?tstart=0
Maybe you are looking for
-
SQL error with LIKE clause in statement
Can anyone explain how an SQL statement with a LIKE clause is executed properly? Seems like it ought to be cut and dried, no pun intended! When I run the following and set the requestor name = ?, and correctly type in the entire name, a result set (a
-
Possible entries for selection screen field
Hi, I have created a custom DDIC table Z_TAB which contains 3 fields of type char. The table contains about 100 rows of data. I want that at the selection screen, for each selection field a list of entries in the table should appear. E.g. Data rows:
-
ICloud error in Mail whenever macbook put to sleep
Hey whenever I wake my MBP from sleep I get an error in Mail and no new mail gets delivered. Does anyone have a solution? Thanks
-
Voicemail alert repeats when opening voicemail?
This has been happening for so long I don't remember when it started, but maybe with iOS 8, or one of the subsequent updates?? The issue is this: I miss a call, and the caller leaves me a message. I have on of the older 'Classic' sounds set as my voi
-
Why Does CC or Apps in CC become unusable after a few weeks or Months?
Seem that ever since Adobe has forced many of its users to use CC and CC Apps that they stop working or will not upgrade after a few weeks to a month or two. ADobe needs to fix this really annoying problem that generally requires uninstalling and rei