.Plist error on system reboot

every time I restart my macbook Pro I get the following message in Textedit. It occurred after using the Ken Burns fade in iMovie. TIA
LocalizedDescrioption.plist
<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">
<plist version="1.0">
<dict>
<key>LOCALIZABLE</key>
<dict>
<key>localizedStyleName</key>
<string>Ken Burns</string>
</dict>
</dict>
</plist>

No, we don't do personal email service here, it is a community forum. Ask and answer here.
You would be wise not put your "partner"s email address on a public forum. Spam, perverts and all will invade that email address. Especially one named as that email address is. Edit your post above to remove it.
See the instructions below and you help her out... Good luck.
First thing? Check the File Free at Options > Status, what is the number at File Free?
Now, remove the battery of your device, hold a minute, replace and reboot. What is the File Free now?
Read this: http://www.blackberryforums.com/general-blackberry-discussion/116396-managing-your-bb-memory-lost-ca...
And this: http://www.blackberryforums.com/general-blackberry-discussion/112029-losing-call-logs-sms-emails-opt...
Additional links to read:
http://www.blackberry.com/btsc/search.do?cmd=displayKC&docType=kc&externalId=KB15345&sliceId=SAL_Pub...
http://www.blackberry.com/btsc/search.do?cmd=displayKC&docType=kc&externalId=KB14320&sliceId=SAL_Pub...
http://www.blackberry.com/btsc/dynamickc.do?externalId=KB14213&sliceId=SAL_Public&command=show&forwa...
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Similar Messages

Remote system reboots due to error when exporting config.

I have a PXI-8196 controller operating on a network in a PXI-1052 chassis. I am trying to export the config and the remote system reboots due to system error.

Your Computer looks to be a Late 2010 iMac, if so is the RAM spec as shown below?
Maximum Memory
16 GB
Memory Slots
4 - 204-pin PC3-10600 (1333 MHz) DDR3 SO-DIMM

I can't see my Canon MG5220 printer... Initially I was getting "there is a communication error" so I rebooted everything, reset the printing system, reinstalled the driver and still NO luck! It seems to see the scanner, but never the printer. HELP!

I can't see my Canon MG5220 printer... Initially I was getting "there is a communication error" so I rebooted everything, reset the printing system, reinstalled the driver and still NO luck! I see no printers available in the Print & Scan area. If I click "+" it seems to see the scanner, but never the printer. HELP!

The printer component uses a different protocol to advertise itself on the network compared to the scanner component and it can take several seconds longer to appear after the scanner has.
That said, with the introduction of AirPrint, the MG should be seen as Bonjour Multifunction in the Add Printer window, as shown below.
Selecting this Bonjour Multifunction entry will create a printer using AirPrint and a scanner using the iCA driver.
So do you see the MG5220 as Bonjour Multifunction or just Bonjour?

Where to find system reboot error message

I saw some error message associated with dbora when I reboot the linux system. But the message disappears very fast. Where is the system reboot error message stored? Or what command that I can use to view the error message?
Thanks!

/var/log
If you can not find logs there, ask your Linux administrator for the location.
Vishal V.

Safari hangs and forces a system reboot

This happens more frequently recently. Out of the blue, Safari (v8.0.3) under OS X 10.10.2 freezes OS X completely and the system reboots. It happens on simple HTML only websites that don't require any scripts - e.g. forums. The screen resolution appears to be lowered when logging back in, but once the system has loaded everything seems to be normal (even Safari remembers all the sites).
Aside from the ongoing WiFi issues, Yosemite is the first Apple OS that seems to crash frequently on me...
Who else is experiencing these issues?
2012 MacBook Pro Retina
16 Gb, 512 Gb SSD

1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
The test works on OS X 10.7 ("Lion") and later. I don't recommend running it on older versions of OS X. It will do no harm, but it won't do much good either.
Don't be put off by the complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. As I wrote above, it changes nothing. It doesn't send or receive any data on the network. All it does is to generate a human-readable report on the state of the computer. That report goes nowhere unless you choose to share it. If you prefer, you can act on it yourself without disclosing the contents to me or anyone else.
You should be wondering whether you can believe me, and whether it's safe to run a program at the behest of a stranger. In general, no, it's not safe and I don't encourage it.
In this case, however, there are a couple of ways for you to decide whether the program is safe without having to trust me. First, you can read it. Unlike an application that you download and click to run, it's transparent, so anyone with the necessary skill can verify what it does.
You may not be able to understand the script yourself. But variations of it have been posted on this website thousands of times over a period of years. The site is hosted by Apple, which does not allow it to be used to distribute harmful software. Any one of the millions of registered users could have read the script and raised the alarm if it was harmful. Then I would not be here now and you would not be reading this message. See, for example, this discussion.
Nevertheless, if you can't satisfy yourself that these instructions are safe, don't follow them. Ask for other options.
4. Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
5. Try to test under conditions that reproduce the problem, as far as possible. For example, if the computer is sometimes, but not always, slow, run the test during a slowdown.
You may have started up in "safe" mode. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
6. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
7. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(1236 ' 0.5 0.25 10 1000 15 5120 1000 25000 1 1 0 100 ' 51 25600 4 10 25 5120 102400 1000 25 1000 80 40 500 300 85 25 20480 262144 20 2000 524288 604800 5 );k=({Soft,Hard}ware Memory Diagnostics Power FireWire Thunderbolt USB Bluetooth SerialATA Extensions Applications Frameworks PrefPane Fonts Displays PCI UniversalAccess InstallHistory ConfigurationProfile CFBundleIdentifier 'com\.apple\.' -\\t N\\/A 'AES|atr|udit|msa|dnse|ax|ensh|fami|FileS|fing|ft[pw]|gedC|kdu|etS|is\.|alk|ODSA|otp|htt|pcas|ps-lp|rexe|rlo|rsh|smb|snm|teln|upd-[aw]|uuc|vix|webf' OSBundle{Require,AllowUserLoa}d 'Mb/s:per sec:ms/s:KiB/s:%:total:MB:total' 'Net in:Net out:I/O wait time:I/O requests:CPU usage:Open files:Memory:Mach ports:File opens:Forks:Failed forks:System errors' 'tsA|[ST]M[HL]' PlistBuddy{,' 2>&1'}' -c Print' 'Info\.plist' );f=('\n%s'{': ','\n\n'}'%s\n' '\nRAM details\n%s\n' '%s %s\n' '%s\n'"${k[22]}"'%s\n' {Privacy,Mode}': %s\n' '\n   ...and %s more line(s)\n' 'RSSI: %s\nNoise: %s\nTx rate: %s\n' '\nContents of %s\n   '"${k[22]}"'mod date: %s\n   '"${k[22]}"'checksum: %s\n%s\n' '%d MB: %s\n' );c=(879294308 4071182229 461455494 3627668074 1083382502 1274181950 1855907737 2758863019 1848501757 464843899 2636415542 3694147963 1233118628 2456546649 2806998573 2778718105 842973933 2051385900 3301885676 891055588 998894468 695903914 1443423563 4136085286 3374894509 1051159591 892310726 1707497389 523110921 2883943871 3873345487 );s=(' s/[0-9A-Za-z._]+@[0-9A-Za-z.]+\.[0-9A-Za-z]{2,4}/EMAIL/g;/faceb/s/(at\.)[^.]+/\1NAME/g;/\/Shared/!s/(\/Users\/)[^ /]+/\1USER/g;s/[-0-9A-Fa-f]{22,}/UUID/g;' ' s/^ +//;/de: S|[nst]:/p;' ' {sub(/^ +/,"")};/er:/;/y:/&&$2<'${p[4]} ' s/:$//;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: (E[^m]|[^EO])|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[9]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Genesy|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' BEGIN { FS=":";if(system("sw_vers -productVersion|grep -q ^10\.1")) d="^'"${k[21]}"'launch(d\.peruser\.[0-9]+|ctl\.(Aqua|Background|System))$";} { if($2~/[1-9]/) { $2="status: "$2;printf("'"${f[4]}"'",$1,$2);} else if(!d||$1!~d) print $1;} ' ' { sub(/ :/,"");print|"tail -n'${p[10]}'";} ' ' NR==2&&$4<='${p[7]}' { print $4;} ' ' ($1~"wir"&&$2>'${p[22]}')||($1~/P.+ts:/&&$2>'${p[19]}') { print $1" "int($2);} ' '/YLD/s/=/ /p' ' { q=$1;$1="";u=$NF;$NF="";gsub(/ +$/,"");print q":"$0":"u;} ' ' /^ {6}[^ ]/d;s/:$//;/([^ey]|[^n]e):/d;/e: Y/d;s/: Y.+//g;H;${ g;s/ \n (\n)/\1/g;s/\n +(M[^ ]+)[ -~]+/ (\1)/;s/\n$//;/( {8}[^ ].*){2,}/p;} ' 's:^:/:p;' ' !/ /{print};END{if(NR<'{${p[12]},${p[13]}}')printf("^'"${k[21]}"'.+")} ' '|uniq' ' 1;END { if(NR<'{${p[14]},${p[21]}}') printf("^/[Sp].+|'${k[21]}'");} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:.+//p;' '&&echo On' '/\.(bundle|component|framework|kext|mdimporter|plugin|qlgenerator|saver|wdgt)$/p' '/\.dylib$/p' ' /Temp|emac/{next};/(etc|Preferences|Launch[AD].+)\// { sub(".","");print $0"$";} END { split("'"${c[*]}"'",c);for(i in c) print "\t"c[i]"$";} ' ' /^\/(Ap|Dev|Inc|Prev)/d;/((iTu|ok).+dle|\.(component|mailbundle|mdimporter|plugin|qlgenerator|saver|wdgt))$/p;' ' $2=="=" { gsub(/[()"]/,"",$3);print $3;} ' ' /^\// { sub("/dev/","",$1);printf("%s: %s\n",$1,$9);} ' '>&-||echo No' '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[2]}'{$2=$2-1;print}' ' BEGIN { M1='${p[16]}';M2='${p[18]}';M3='${p[8]}';M4='${p[3]}';} !/^A/{next};/%/ { getline;if($5<M1) o["CPU"]="CPU: user "$2"%, system "$4"%";next;} $2~/^disk/&&$4>M2 { o[$2]=$2": "$3" ops/s, "$4" blocks/s";next;} $2~/^(en[0-9]|bridg)/ { if(o[$2]) { e=$3+$4+$5+$6;if(e) o[$2]=o[$2]"; errors "e"/s";next;};if($4>M3||$6>M4) o[$2]=$2": in "int($4/1024)", out "int($6/1024)" (KiB/s)";} END { for(i in o) print o[i];} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|BKAg|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/)||(/v6:/&&$2!~/A/) ' ' $1=="op" {m=$3};$1~"lN" {N=$2};$1~"lR" {S=$2};$1~"Tx" {T=$2};$1~/^st/ {s=$2};$1~"li"&&$3!~"wpa2" {printf("'"${f[5]}"'",toupper($3))};END { if(S*N*T&&(S-N<'${p[5]}'||T<'${p[20]}')) printf("'"${f[8]}"'",S,N,T);if(s~/^r/&&m!~/^st/) printf("'"${f[6]}"'",m);} ' ' BEGIN { FS=":";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]$1;} ' ' BEGIN { split("'"${p[1]}"'",m);FS=":";} $2<=m[$1]{next} $1<9 { o[$1]=o[$1]"\n   "$3" (UID "$4"): "$2;} $1==9&&$5!~"^/dev" { o[$1]=o[$1]"\n   "$3" (UID "$4") => "$5" (status "$6"): "$2;} $1==10&&$5 { p="ps -c -ocomm -p"$5"|sed 1d";p|getline n;close(p);if(n) $5=n;o[$1]=o[$1]"\n   "$5" => "$3" UID ("$4"): "$2;} $1~/1[12]/ { o[$1]=o[$1]"\n   "$3" (UID "$4", error "$5"): "$2;} END { n=split("'"${k[27]}"'",u,":");for(i=n+1;i<n+5;i++)u[i]=u[2];split("'"${k[28]}"'",l,":");for(i in o) print "\n"l[i]" ("u[i]")\n"o[i];} ' ' /^ {8}[^ ]/{print} ' ' BEGIN { L='${p[17]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n   "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n   [N/A]";"cksum "F|getline C;split(C, A);C=A[1];"stat -f%Sm "F|getline D;"file -b "F|getline T;if(T~/^Apple b/) { f="";l=0;while("'"${k[30]}"' "F|getline g) { l++;if(l<=L) f=f"\n   "g;};};if(T!~/^(AS.+ (En.+ )?text(, with v.+)?$|(Bo|PO).+ sh.+ text ex|XM)/) F=F"\n   '"${k[22]}"'"T;printf("'"${f[9]}"'",F,D,C,f);if(l>L) printf("'"${f[7]}"'",l-L);} ' ' s/^ ?n...://p;s/^ ?p...:/-'$'\t''/p;' 's/0/Off/p' 's/^.{52}(.+) <.+/\1/p' ' /id: N|te: Y/{i++} END{print i} ' ' /kext:/ { split($0,a,":");p=a[1];k[S]='${k[25]}';k[U]='${k[26]}';v[S]="Safe";v[U]="true";for(i in k) { s=system("'"${k[30]}"'\\ :"k[i]" \""p"\"/*/I*|grep -qw "v[i]);if(!s) a[1]=a[1]" "i;};if(!a[2]) a[2]="'"${k[23]}"'";printf("'"${f[4]}"'",a[1],a[2]);next;} !/^ *$/ { p="'"${k[31]}"'\\ :'"${k[20]}"' \""$0"\"/*/'${k[32]}'";p|getline b;close(p);if(b~/ /||b=="") b="'"${k[23]}"'";printf("'"${f[4]}"'",$0,b);} ' '/ en/!s/\.//p' ' NR>=13 { gsub(/[^0-9]/,"",$1);print;} ' ' $10~/$L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9|"sort|uniq";} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?'${k[32]}'$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' ' /l: /{ /DVD/d;s/.+: //;b0'$'\n'' };/s: /{ / [VY]/d;s/^ */- /;H;};$b0'$'\n'' d;:0'$'\n'' x;/APPLE [^:]+$/d;p;' '/^find: /!p;' ' /^p/{ s/.//g;x;s/\nu/:/;s/(\n)c/\1:/;s/\n\n//;p;};H;' ' BEGIN{FS="= "} /Path/{print $2} ' ' /^ *$/d;s/^ */   /;p;' ' s/^.+ |\(.+$$//g;p;' '1;END{if(NR<'${p[15]}')printf("^/(S|usr/(X|li))")}' ' /2/{print "WARN"};/4/{print "CRITICAL"};' ' /EVHF|MACR|^s/d;s/^.+: //p;' ' $3~/^[1-9][0-9]{0,2}(\.[1-9][0-9]{0,2}){2}$/ { i++;n=n"\n"$1"\t"$3;} END{ if(i>1)print n} ' s/{'\.|jnl: ','P.+:'}'//;s/ +([0-9]+)(.+)/\2 \1/p' ' /es: ./{ s/^.+://;b0'$'\n'' };/^ +C.+ted: +[NY]/H;/:$/b0'$'\n'' d;:0'$'\n'' x;/: +N/d;s/\n.+//p;' ' 1d;/:$/b0'$'\n'' $b0'$'\n'' /(D|^ *Loc.+): /{ s/^.+: //;H;};/(B2|[my]): /H;d;:0'$'\n'' x;/[my]: [AM]|m: I.+p$|^\/Vo/d;s/(^|\n) [ -~]+//g;s/(.+)\n(.+)/\2:\1/;s/\n//g;/[ -~]/p;' 's/$/:(0|-(4[34])?)$/p' '|sort'{'|uniq'{,\ -c},\ -nr} ' s/^/'{5,6,7,8}':/;s/ *: */:/g;p;' '/e:/{print $2}' ' /^[(]/{ s/....//;s/$/:/;N;/: [)]$/d;s/\n.+ ([^ ]+).$/\1/;H;};${ g;p;} ' 's/:.+$//p' '|wc -l' /{\\.{kext,xpc,'(appex|pluginkit)'}'\/(Contents\/)?'Info,'Launch[AD].+'}'\.plist$/p' 's/([-+.?])/\\\1/g;p' 's/, /\'$'\n/g;p' ' BEGIN{FS=":"} { printf("'"${f[10]}"'",$1/1048576,$2);} ' ' /= D/&&$1!~/'{${k[24]},${k[29]}}'/ { getline d;if(d~"t") D=D"\n"$1;} END { print D;} ' ' NR>1&&$3!~/0x|\.([0-9]{3,}|[-0-9A-F]{36})$/ { print $3":"$2;} ' '|tail -n'${p[6]} ' $1>1 { $NF=$NF" x"$1;} /\*/ { if(!f) f="\n\t* Code injection";} { $1="";} 1;END { print f;} ' ' s/.+bus /Bus: /;s/,.+[(]/ /;s/,.+//p;' ' { $NF=$NF" Errors: "$1;$1="";} 1 ' ' 1s/^/\'$'\n''/;/^ +(([MNPRSV]|De|Li).+|Bus): ./d;s/:$//;p;' 's/,.+"//p' '|grep -q e:/' '/[^ .]/p' '{ print $1}' ' BEGIN{ FS=": "} /^C/ { getline t;if(a[split(t,a)]) print $2;} ' ' 1s/^/\'$'\n''/;3,4d;$d;/^ +D|Of|Fu| [0B]/d;s/^ {4}|:$//g;p;' ' BEGIN { FS=":";} NR==1 { print "\n"$1"\n";} /:$/ { l=$1;next;} $1~"S"&&$2!~3 { getline;next;} /^ {6}I/ { i++;sub(/,.+/,"");L[i]=l$2;if(i=='${p[24]}') nextfile;} END { for(j=0;j<i;j++) print L[i-j];} ' ' /services =/,/[\}]/!d;/[=\}]/!p ' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps crontab kextfind top pkgutil "${k[30]}\\" echo cksum kextstat launchctl smcDiagnose sysctl\ -n defaults\ read stat lsbom 'mdfind -onlyin' env pluginkit scutil 'dtrace -q -x aggsortrev -n' security sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil lsof test osascript\ -e netstat mdls route egrep 'dscl . -read' );c2=(${k[21]}loginwindow\ LoginHook ' /L*/P*/loginw*' "'tell app \"System Events\" to get properties of login items'" 'L*/Ca*/'${k[21]}'Saf*/E* -d 2 -name '${k[32]} '~ $TMPDIR.. $ -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 $' -i '-nl -print' '-F \$Sender -k Level Nle 3 -k Facility Req "'${k[21]}'('{'bird|.*i?clou','lsu|sha'}')"' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$Message' -k Sender kernel -k Message CRne '0xdc008012|calling|(mplet|nabl)ed|ry HD|safe b' -k Message CReq 'bad |Can.t l|corru|dead|fail|GPU |hfs: Ru|inval|Limiti|v_c|NVDA|pagin|Purg|error|Refus|TCON|tim(ed? ?|ing )o|WARN' " '-du -n DEV -n EDEV 1 10' 'acrx -o%cpu,comm,ruid' "' syscall::recvfrom:return {@a[execname,uid]=sum(arg0)} syscall::sendto:return {@b[execname,uid]=sum(arg0)} syscall::open*:entry {@c[execname,uid,copyinstr(arg0),errno]=count()} syscall::execve:return, syscall::posix_spawn:return {@d[execname,uid,ppid]=count()} syscall::fork:return, syscall::vfork:return, syscall::posix_spawn:return /arg0<0/ {@e[execname,uid,arg0]=count()} syscall:::return /errno!=0/ {@f[execname,uid,errno]=count()} io:::wait-start {self->t=timestamp} io:::wait-done /self->t/ { this->T=timestamp - self->t;@g[execname,uid]=sum(this->T);self->t=0;} io:::start {@h[execname,uid]=sum(args[0]->b_bcount)} tick-10sec { normalize(@a,2560000);normalize(@b,2560000);normalize(@c,10);normalize(@d,10);normalize(@e,10);normalize(@f,10);normalize(@g,10000000);normalize(@h,10240);printa(\"1:%@d:%s:%d\n\",@a);printa(\"2:%@d:%s:%d\n\",@b);printa(\"9:%@d:%s:%d:%s:%d\n\",@c);printa(\"10:%@d:%s:%d:%d\n\",@d);printa(\"11:%@d:%s:%d:%d\n\",@e);printa(\"12:%@d:%s:%d:%d\n\",@f);printa(\"3:%@d:%s:%d\n\",@g);printa(\"4:%@d:%s:%d\n\",@h);exit(0);} '" '-f -pfc /var/db/r*/'${k[21]}'*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cght] ! -name .?\* ! -name \*ag $ -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true $ -execdir stat -f:%Sc:%N -t%F {} \;' '/S*/*/Ca*/*xpc*' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' /\ kMDItemContentTypeTree=${k[21]}{bundle,mach-o-dylib} :Label "/p*/e*/{aut*,{cron,fs}tab,hosts,{[lp],sy}*.conf,mach_i*/*,pam.d/*,ssh{,d}_config,*.local} {/p*,/usr/local}/e*/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t {/S*/,/,}L*/{Lau,Sec}*/*t .launchd.conf" list '-F "" -k Sender hidd -k Nle 3' /Library/Preferences/${k[21]}alf\ globalstate --proxy '-n get default' -I --dns -get{dnsservers,info} dump-trust-settings\ {-s,} '' -n1 '-R -ce -l1 -n5 -o'{'prt -stats prt','mem -stats mem'}',command,uid' -kl -l -s\ / '--regexp --files '${k[21]}'pkg.*' '+c0 -i4TCP:0-1023' ${k[21]}dashboard\ layer-gadgets '-d /L*/Mana*/$USER' '-app Safari WebKitDNSPrefetchingEnabled' '-Fcu +c0 -l' -m 'L*/{Con*/*/Data/L*/,}Pref* -type f -size 0c -name *.plist.???????' kern.memorystatus_vm_pressure_level '3>&1 >&- 2>&3' '-F \$Message -k Sender kernel -k Message CReq "'{'n Cause: -','(a und|I/O |jnl_io.+)err','USBF:.+bus'}'"' -name\ kMDItem${k[20]} -T\ hfs '-n get default' -listnetworkserviceorder :${k[20]} :CFBundleDisplayName $EUID {,'/{S*/,}'}'L*/{,Co*/*/*/L*/}{Cache,Log}s $TMPDIR../C -type f -size +'${p[11]}'M -exec stat -f'%z:%N' {} \;' \ /v*/d*/*/*l*d{,.*.$UID}/* '-app Safari UserStyleSheetEnabled' "-o ',\"name\":\"[^\"]+' L*/A*/Fi*/P*/*/a*.json" users/$USER\ HomeDirectory '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' ' -F "\$Time \$Sender \$(RefProc): \$Message" -k Level Nle 3 -k Facility R'{'ne "user|','eq "'}'console" -k Message CRne "^[ }]|deprec|sandbox ex" ' getenv '/ "kMDItemDateAdded>=\$time.now(-'${p[23]}')&&kMDItem'${k[20]}'=*"' -m\ / print\ system );N1=${#c2[@]};for j in {0..19};do c2[N1+j]=SP${k[j]}DataType;done;l=({Restricted\ ,Lock,Pro}files POST Battery {Safari,App,{Bad,Loaded}\ kernel,Firefox}\ extensions System\ load boot\ args FileVault\ {2,1} {Kernel,System,Console}\ log Activity SMC Login\ hook 'I/O per process' 'High file counts' UID Daemons Agents XPC\ cache Startup\ items {Admin,Root}\ access Stylesheet Library\ paths{,' ('{shell,launchd}\)} Font\ issues Firewall Proxies DNS TCP/IP Wi-Fi 'Elapsed time (sec)' {Root,User}\ crontab {Global,User}' login items' Spotlight Memory\ pressure Listeners Widgets Parental\ Controls Prefetching Nets Volumes {Continuity,I/O,iCloud,HID,HCI}\ errors {User,System}\ {caches/logs,overrides} Shutdown\ codes Heat Diagnostic\ reports Bad\ plists Free\ space VM Bundles{,' (new)'} 'Trusted certs ('{system,user}\) );N3=${#l[@]};for i in {0..8};do l[N3+i]=${k[5+i]};done;F() { local x="${s[$1]}";[[ "$x" =~ ^([\&\|\<\>]|$) ]]&&{ printf "$x";return;};:|${c1[30]} "$x" 2>&-;printf "%s \'%s\'" "|${c1[30+$?]}" "$x";};A0() { Q=6;v[2]=1;id -G|grep -qw 80;v[1]=$?;((v[1]))||{ Q=7;sudo -v;v[2]=$?;((v[2]))||Q=8;};v[3]=`date +%s`;date '+Start time: %T %D%n';printf '\n[Process started]\n\n'>&4;printf 'Revision: %s\n\n' ${p[0]};};A1() { local c="${c1[$1]} ${c2[$2]}";shift 2;c="$c ` while [[ "$1" ]];do F $1;shift;done`";((P2))&&{ c="sudo $c";P2=;};v=`eval "$c"`;[[ "$v" ]];};A2() { local c="${c1[$1]}";[[ "$c" =~ ^(awk|sed ) ]]&&c="$c '${s[$2]}'"||c="$c ${c2[$2]}";shift 2;local d=` while [[ "$1" ]];do F $1;shift;done`;((P2))&&{ c="sudo $c";P2=;};local a;v=` while read a;do eval "$c '$a' $d";done<<<"$v";`;[[ "$v" ]];};A3(){ v=$((`date +%s`-v[3]));};B1() { v=No;! ((v[1]))&&{ v=;P1=1;};};eval "`type -a B1|sed '1d;s/1/2/'`";B3(){ v[$1]="$v";};B4() { local i=$1;local j=$2;shift 2;local c="cat` while [[ "$1" ]];do F $1;shift;done`";v[j]=`eval "{ $c;}"<<<"${v[i]}"`;};B5(){ v="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`egrep -v "${v[$1]}"<<<"$v"|sort`;};eval "`type -a B7|sed '1d;s/7/8/;s/-v //'`";C0() { [[ "$v" ]]&&sed -E "$s"<<<"$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v"|sed -E "$s";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { B4 0 0 63&&C1 1 $1;};C4() { echo $'\t'"Part $((++P)) of $Q done at $((`date +%s`-v[3])) sec">&4;};C5() { sudo -k;pbcopy<<<"$o";printf '\n\tThe test results are on the Clipboard.\n\n\tPlease close this window.\n';exit 2>&-;};for i in 1 2;do eval D$((i-1))'() { A'$i' $@;C0;};';for j in 2 3;do eval D$((i+2*j-3))'() { local x=$1;shift;A'$i' $@;C'$j' $x;};';done;done;trap C5 2;o=$({ A0;D0 0 N1+1 2;D0 0 $N1 1;B1;C2 27;B1&&! B2&&C2 28;D2 22 15 63;D0 0 N1+2 3;D0 0 N1+15 17;D4 3 0 N1+3 4;D4 4 0 N1+4 5;D4 N3+4 0 N1+9 59;D0 0 N1+16 99; for i in 0 1 2;do D4 N3+i 0 N1+5+i 6;done;D4 N3+3 0 N1+8 71;D4 62 1 10 7;D4 10 1 11 8;B2&&D4 18 19 53 67;D2 11 2 12 9;D2 12 3 13 10;D2 13 42 70 101 25;D2 65 6 76 13;D2 45 20 52 66;D4 66 7 37 14;D4 17 8 15 38;D0 9 16 16 77 45;C4;B2&&D0 35 49 61 75 76 78 45;B2&&{ D0 28 17 45;C4;};D0 12 40 54 16 79 45;D0 12 39 54 16 80 45;D4 31 25 37 15&&{ B4 0 8 103;B4 8 0;A2 18 74;B6 8 0 3;C3 32;};B2&&D4 19 21 0;B2&&D4 40 10 42;D2 2 0 N1+19 46 84;D2 44 34 43 53;D2 25 22 20 32;D2 33 0 N1+14 51;D4 69 29 35 104 75 96;D4 70 29 36 104 75 96;D2 34 21 28 35;D4 35 27 29 36;A1 40 59 81;B3 18;A1 33 60 82;B8 18;B4 0 19 83;A1 27 32 39&&{ B3 20;B4 19 0;A2 33 33 40;B3 21;B6 20 21 3;};C2 36;D4 50 38 5 68;B4 19 0;D5 37 33 34 42;B2&&D4 46 35 45 55;D4 38 32 31 43;B2&&D4 59 4 65 76 91;D4 63 4 19 44 75 95 96;B1&&{ D4 53 5 55 75 69&&D4 51 6 58 31;D4 56 5 56 97 75 98&&D0 0 N1+7 99;D2 55 5 27 84;D4 61 5 54 75 70;D4 14 5 14 12;D4 15 5 72 12;C4;};D4 16 5 73 12;A1 13 44 74 18;C4;B3 4;B4 4 0 85;A2 14 61 89;B4 0 5 19 102;A1 17 41 20;B7 5;C3 8;B4 4 0 88;A2 14 24 89;C4;B4 0 6 19 102;B4 4 0 86;A2 14 61 89;B4 0 7 19 102;B5 6 7;B4 0 11 73 102;A1 18 77 107 94 74||{ B2&&A1 18 26 94 74;}&&{ B7 11;B4 0 0 11;C3 23;};A1 18 26 94;B7 11;B4 0 0 11;C3 24;D4 60 14 66 92;D4 58 14 67 93;D4 26 4 21 24;D4 42 14 1 62;D4 43 37 2 90 48;D4 41 10 42;D2 48 36 47 25;A1 4 3 60&&{ B3 9;A2 14 61;B4 0 10 21;B4 9 0;A2 14 62;B4 0 0 21;B6 0 10 4;C3 5;};D4 9 41 69 100;D2 29 21 68 35;D2 49 21 48 49;B4 4 22 57 102;A1 21 46 56 74;B7 22;B4 0 0 58;C3 47;D4 54 5 7 75 76 69;D4 52 5 8 75 76 69;D4 57 4 64 76 91;D2 0 4 4 84;D2 1 4 51 84;D4 21 22 9 37;D0 0 N1+17 105; A1 23 18 28 89;B4 0 16 22 102;A1 16 25 33;B7 16;B4 0 0 34;D1 31 47;D4 64 4 71 41;C4;B4 4 12 26 89 23 102;for i in {0..3};do A1 0 N1+10+i 72 74;B7 12;B4 0 0 52;C3 N3+5+i;((i))||C4;done;A1 24 22 29;B7 12;B3 14;A2 39 57 30;B3 15;B6 14 15 4;C3 67;A1 24 75 74;B3 23;A2 39 57 30;B3 24;B6 23 24 4;C3 68;B4 4 13 27 89 65;A1 24 23;B7 13;C3 30;B4 4 0 87;A2 14 61 89 20;B4 0 17;A1 26 50 64;B7 17;C3 6;D0 0 N1+18 106;D4 7 11 6;A3;C2 39;C4;} 4>&2 2>/dev/null;);C5
Copy the selected text to the Clipboard by pressing the key combination command-C.
8. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
9. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
exec bash
and press return. Then paste the script again.
10. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
11. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, a series of lines will appear in the Terminal window like this:
[Process started]
        Part 1 of 8 done at … sec
        Part 8 of 8 done at … sec
        The test results are on the Clipboard.
        Please close this window.
[Process completed]
The intervals between parts won't be exactly equal, but they give a rough indication of progress. The total number of parts may be different from what's shown here.
Wait for the final message "Process completed" to appear. If you don't see it within about ten minutes, the test probably won't complete in a reasonable time. In that case, press the key combination control-C or command-period to stop it. Then go to the next step.
12. When the test is complete, or if you stopped it because it was taking too long, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with the words "Start time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
13. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "You are not authorized to post." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
14. This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I may not agree with them.
Copyright © 2014, 2015 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

System reboots

The operating system starts normally and after a short period, it reboots. Can not find the problem. I have installed the latest drivers 4 all of my devices. It reboots faster when i play a game. Hitman Contracts, Thief 3 Deadly Shadows. The CPU temp will under load go up to about 50.C. Might that be the problem? Please help!!!
Mainboard : S-478 Intel 865PE Neo2-PFISR
VGA: Saphire Raddeon 9700 128mb
Ram: Geil GD3200-512DC 2x256mb PC3200 DDR CL2 2,5-2,9V 400MHz
CPU: Pentium 4 S-478 2,6GHz 800MHz 512kb Boxed Northwood
OS: WinXP Pro SP1 DirectX9b
PWR: Enermax Whisper 430w, 3,3V/38A, +5V/44A, +12V/20A,
HD: 80gb WD ATA 100

Quote
Originally posted by DassPriesT
Everything worked stable for 3 days, and suddenly when i was transfering 10gb of data over LAN the system reboots again. When i started transfering data over again the same happened. What is wrong???
Hi,
Do you receive an error message? "Your system will reboot in 60seconds please save all work"
I would just like to be sure you do not have Sasser......
Del UK

System reboots with audigy2 value. get irql less than or not equil. please help new c

hello my name is carlos
my system reboots at random (more in games) with audigy 2 value..
could someone please advise me on the problem i have with my new audigy 2 card. i would like to get it working and not have to get another card. i got this one because my onboard sound is so junky with midi music and has a poor s/n on recording. the blaster card seems to meet my expectations except for the reboots.
i have read on forums about this same issue with ati video cards in the 9200+ range so i thought that might be the cause but i went back to the onboard audio and the problem went away.
at random my system reboots. i get an error.. irql_not less than or equil or something like that and then it reboots. i let it submit to microsoft and they only say its a problem with a device driver. i have all the updated drivers for all my hardware at this point. i have all the windows updates as well. my xp is legal. i dont think its the power supply but.. could it be? the readings with my digital meter are normal. i have an older but quality digital multi tester. got it when in college. so i know its accurate. it reads 4.9 on 5 and 2.2 on 2. all this info because of the information i have read already. is the audigy a power hungry card? cause i dont get any reboots when i use the onboard sound and my ati video so what ever is going on it has something to do with the sound card.
i cant find a newer driver on the driver site for it except for the beta. so i assume there is no updated driver for the card.
i have a ups backup system. it has come on but it has never caused a computer hang when it has. its a 250 watt unit with plenty of battery backup. same battery backs up my ham radio equip. i am going to reinstall the card and see if in some chance it is munipulating the waveform to the supply. the power to the machine reads 22 volts.
i have had some issues with the power company recently. they had to do some major repairs because i was having problems with flickers. but they fixed... [Show more]

thank you for your reply to my problem.
sorry i missed that detail in my information. that is one of the things i checked. video is on 6 and audio is on 7. i dont see any other devices sharing those irqs in the device manager irq information. or any other devices on same irqs or i/o
before anyone mentions it i also have 3 fans sucking air. my case is actually an old server case with lots of vent holes in front and side. i was thinking of getting some of the slot fans and blowing on video and sound card. could this be the issue? the monitor app says my sytem temp is 82 degrees. 27 on processor.
i appreaciate the input. i ran it all night last night with nero media player running with visulations on. the music was still playing but the video was locked up when i checked it this morning? nothing but mushrooms on my screen from the visulation. i dont know if something happened with nero (most likely this time) but thats the first time that error came up. the odd thing about this really is that it may go for hours and not do this but it seems to do it more when we play demanding games. i ran the machine yesterday for hours on my inverter (ups system) from the batteries with no problem. its output is just a little hotter than my house voltage 27 volts and my line volatage is about 9. but it may reboot before i get this post completed. it ran without problem for 7 hours with all the major games i have until the batteries ran down. (two high capacity 2 volt deep cycles on the outside deck)its really odd. its almost at random. at this point i suspect that i have a power supply problem of some sort. im gonna get a new supply by friday and see if that hel
ps.
i have to wonder who makes the best supply? anyone have any sujestions? perhaps whats really causing this is the capacitors in the supply cant sustain a clean output with the shaky power supplied by aep at my home. aep says that they fixed the problem but i still see flickers. i dont have any problems with the power on anything else in my home. im a little particular. lights that flicker bug me. its not a serious flicker just a slight diming that i have tried to catch with a dvm meter and cant. i have a 350 watts supply but its probably not the best made supply out there. i bought it at a local place that sells off brand computer parts. my fault i guess.. i've had it for maybe 3 years. i had a supply go bad back then and ruin a hard dri've on me. im bad for giving more info than needed but im just a yacker. thanks for the help..

System reboots if inactive

Hello,
Sins I upgraded to leopard I had this strange bug that make my system reboot if I'm inactive for ~1 hour.
I hopped it would be better after 10.5.1 but that upgrade didn't help. =(
I'm having a macbook with the energy saving option on never turn of hard disk or put computer to sleep.
Anyone have an idea of whats wrong please tell me.

+"...The problem I had with Eytv was that I had a setting that enabled the computer to wake so it could go on line and get updated TV schedules. This happen at some point < one hour."+
So If I understand right my problem could be because of Aurora, for it set to wake my computer then it's morning. I will try to run a day without anything that have with aurora to do and see if it's get better. ;)
Well here is a long list with programs I had running and the log message from last night when I went to bed until I woke up.
*Program list (all up-to-date)*
iTunes
Transmission
Dock
Finder
Quicksilver
SystemUIServer
Loginwindow
GrowlHelperApp
mdworker
ATSServer
Aurora Wakeup Helper
AppleSpell.service
Spotlight
PenTableDriver
iTunes Helper
SteerMouse Manager
UserEventAgent
TabletDriver
ssh-agent
pboard
lauchd
*Log from (LOG DATABASE QUERIES >> All Messages)*
11/18/07 12:00:04 AM Mail[543] IPCClient: Server port 0 is invalid; looking it up again...
11/18/07 12:09:04 AM login[527] DEAD_PROCESS: 527 ttys000
11/18/07 12:10:01 AM com.apple.launchd[258] ([0x0-0x12012].com.apple.finder[397]) Exited: Terminated
11/18/07 12:18:28 AM login[1066] USER_PROCESS: 1066 ttys000
11/18/07 12:36:52 AM [0x0-0xd00d].com.apple.dock[392] CPSPostEventRecordTo failed -600 /System/Library/CoreServices/Dock.app/Contents/Resources/Widgets.wdgt/
11/18/07 12:36:52 AM [0x0-0xd00d].com.apple.dock[392] CPSPostEventRecordTo failed -600 /System/Library/CoreServices/Dock.app/Contents/Resources/Widgets.wdgt/
11/18/07 12:40:23 AM login[1066] DEAD_PROCESS: 1066 ttys000
11/18/07 12:40:25 AM login[1112] USER_PROCESS: 1112 ttys000
11/18/07 12:41:47 AM login[1112] DEAD_PROCESS: 1112 ttys000
11/18/07 12:42:06 AM com.apple.launchd[258] (0x10e300.Locum[1123]) Exited: Terminated
11/18/07 10:13:01 AM Aurora[1458] deleting stale playlists
11/18/07 10:13:01 AM Aurora[1458] found playlist "(null)" for old playlist "WakeUp"
11/18/07 10:13:01 AM Aurora[1458] found playlist "(null)" for old playlist "WakeUp"
11/18/07 10:13:02 AM [0x0-0xba0ba].de.metaquark.Aurora[1458] 2007-11-18 10:13:02.513 wakeup_helper[1460:10b] de.metaquark.Aurora: scheduling wakepoweron for 2007-11-19 06:43:00 +0100
11/18/07 10:13:03 AM Aurora[1458] checking for startup alarms
11/18/07 10:13:03 AM Aurora[1458] auto-running alarm "WakeUp (old)" (2007-11-18 10:13:00 +0100)
11/18/07 10:13:03 AM Aurora[1458] Fetching iTunes playlists...
11/18/07 10:13:03 AM Aurora[1458] deleting stale playlists
11/18/07 10:13:03 AM Aurora[1458] found playlist "(null)" for old playlist "WakeUp"
11/18/07 10:13:03 AM Aurora[1458] found playlist "(null)" for old playlist "WakeUp"
11/18/07 10:13:03 AM Aurora[1458] Playlists fetched
11/18/07 10:13:03 AM Aurora[1458] .sdef error: Operation could not be completed. (NSXMLParserErrorDomain error 1549.)
11/18/07 10:13:03 AM Aurora[1458] line number: 2
11/18/07 10:13:04 AM Aurora[1458] .sdef error: Operation could not be completed. (NSXMLParserErrorDomain error 1549.)
11/18/07 10:13:04 AM Aurora[1458] line number: 2
11/18/07 10:13:05 AM Aurora[1458] Warning: this alarm has no playlist set, using the default playlist
11/18/07 10:14:03 AM dashboardadvisoryd[1465] fetch-parsers: unable to fetch data from read stream
11/18/07 10:14:03 AM dashboardadvisoryd[1465] fetch: unable to fetch data from read stream while fetch advisory list

System reboot itself randomely and black sreen

I have this MB (Bios 7.6, Msi K7N2 DELTA ILSR (M6570)) since Dec 2003 without problems, very stable.Last week i decide to upgrade Bios (7.8) and at that point pc was booting itself randomely also geting some blackscreen....
I re-install Xp, i re-flash Bios back to 7.6 and still getting the same problems.
If someone have some advice or any hint. Please let me know. Thanks....

System reboots might be attributed to various factors like Memory, PSU and software crashes.
Well to start off disable the system restart option in Startup & recovery option in system properties. To reach there :
Right Click My Computer->Advanced->startup and recovery
Uncheck restart computer on error
Now After doing the above step will come to know if any application or drivers are causing a reboot. You will usually get a memory dump and name of the file causing the dump.
Secondly check for system temps, are any of the fans noisy?? not working???
Check the idle and load temps
feel the air coming out of the PSU exhasut, is it mild warm or really cooked up??
Last but not the least check whether this occurs in any particular application/game or whether you can reproduce the crash/reboot. This will provide insight to resolving the problem quickly and effectively.
hope this helps
Thanks
Rajiv

Input system error, the system is being restarted

I get this message "input system error, the system is being restarted" when i press the spacebar when texting. It freezes after every word for about 3 seconds then back to normal. but keeps doing it every time i press speacebar. any help?

Hi and Welcome to the Community!
Anytime random strange behavior or sluggishness creeps in, the first thing to do is a battery pop reboot. With power ON, remove the back cover and pull out the battery. Wait about a minute then replace the battery and cover. Power up and wait patiently through the long reboot -- ~5 minutes. See if things have returned to good operation. Like all computing devices, BB's suffer from memory leaks and such...with a hard reboot being the best cure.
Best!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

I had to reboot my iMac, it froze... When I went to reboot it started up as usual... Made power sound, showed apple logo (white screen)... And pin wheel started after 3 to 4 mins., went tblack screen with error messages. Rebooted 5x, won't go paspinwheel

I had to reboot my iMac, it froze... When I went to reboot it started up as usual... Made power sound, showed apple logo (white screen)... And pin wheel started after 3 to 4 mins., went to black screen with error messages. Rebooted 5x, shot off power source, disconnected external devices... Now won't go past pinwheel... Since it does not go to black screen, I cannot convey error messages... Please advise what I could try... Thank you... I have an iMac 2009... Upgrade operating system to new system this spring... Don.

It is guitardad's again... I read past topics on this issue... As I am not overly computer savvy, I want to be careful that I don't mess things up further... Of course the extended warranty is done... There is talk about booting from the system disc... I'm not sure if this is the first thing to do or not... Can the support community, advise me on what logical steps I should take ( in order) or direct me to a website and/ or you tube video that walks one safely through the processes... Once again thank you for reading and offering your advice... I am on fixed $$$ so I'm trying to avoid calling apple, unless I have no options and/or the suggestions do not resolve the issues... Tx again Don.

Critical error and random reboots

I have gotten critical errors and random reboots lately =( and it really stinks.. anyone who know what the problem might be?
Is it my 40gb IDE hardrive I just put in?
And it only happens in games

How is your HD doing for heat? When my HDs started getting hot my system kept crashing and rebooting as well. My other thought is to try and uninstall, then re-install video drivers (with the latest drivers of course). There have been times when my system has crashed becasue my vid drivers were on the fritz. Anyways, those are just some of my thoughts.
and just like cultie said, check the jumpers to make sure they are on the correct master/slave pins.

Please help system reboots

All of the stuff I have is listed in my gig. My system has been randomly rebooting. Windows XP installed ok and the system runs ok enough for me to surf the web. It kind of has me stumped I can be on it for a long time and surf the web and it is fine, I have only installed one game simpsons hit and run and after playing that for a little while the system reboots. Sometimes it happens when I am not playing a game too . I used to have a Geforce 4 in the system and the reboots would happen after playing the simpsons for like 1 minute or 2 so I installed a radeon becuase I was planning to upgrade anyway. The system was running more stable with the radeon but today it rebooted on me again after playing the simpsons lfor like an hour. It would reboot and tell me the system recovered from a serious error BPCode:d1 yadda yadda os_ver and some other stuff. I set it to not reboot from an error and today it quit out of the simpsons and sent me to the desktop, I told it to shut down and thats when it gave me a blue screen and said something to the effect of ERROR_IRQL_NOT_ LESS_THAN. I tried testing my RAM and it passed 9 out of 11 tests but I had to go to work so I did not test it fully. Back when I had the geforce 4 in there i tried setting the FSB to 201 and that helped with overall system stability but it still rebooted alot. Tried uping RAM voltage to 2.70 and that helped a little too but system still reboots. I read in another post you guys said not to have SATA+PATA enabled but wouldn't the system not find CD-ROMS if I was set to SATA only? If anyone has seen this before or has any ideas please let me know any ideas or what else you might need to know. I will check RAM tonight and let memtest run all tests and check back here but if anyone has any ideas about this then please let me know.

Hey, NovJoe asked you about memory timings and that was the first thing I was going to ask you too. I have a similar system I'll list on the bottom. I have the Corsair 512x2 PC3700 @3,4,4,8 timing.....My system used to reboot itself A LOT. For NO apparant reason, no matter what I was doing, playing a game, chating online, or surfing websites. I've always had something wrong with my system so I can't tell you exactly what will help, but maybe you can check out some things and decide if you want to change them.
I guess first, you need to make sure all your voltage settings are right. Your processor will run OK with the stock voltages, but uping them a little doesnt hurt. I have mine at 1.55...
Your memory timings should be set at 2.7....The Bios auto is 2.5, but there have been a lot of posts and reviews that say uping the memory voltage to 2.7 (even PC3200), will give you better stability. I have mine at 2.75 because I overclock....I wouldnt recommend anything above 2.7 for you though unless you choose to...I've learned AGP voltages should be at 1.5, nothing more.
On the software side, my random reboots and lockups has 75% of the time corrupted important windows system files. Sometimes a little icon will appear at the corner next to the time, other times I will get no message. Run "chkdsk" through "Start" ~> "Run" and type "CHKDSK" in. If you have, good, but this is only one program to run. Disk Defragmenter also checks for corrupt files and will let you know if you have any.
Your reboots could be due to a corrupt file, and it doesnt have to be a Windows file either. I installed "CORECENTER" at least 3 time, fresh installs and updates, and I didnt have to run the program for it to corrput my system. I ended up deleting it and have not used it since.
I guess if your not sure a program is the problem, the last resort you should take is to format your system. I've formatted at least 15 times (my luck) and I'm sorry to say I've gotten used to it...I just partition my hard drive and store EVERYTHING important on it...so that if Windows refuses to boot or locks up and doesnt want ot start, I can safely partition the WINDOWS parition without loosing any of my data. Windows will even let you have partions with different file systems such as NTFS or FAT32 at the same time....(this is my case).
Ahhhh....I was writing my specs and I REMEMBERED SOMETHING! Corny i know, i'm on medication ...... anyway....try to run your MAT..found in BIOS under "Frequency and Voltage" (or something like that) to "FAST"....I know if I set it to "Ultra", my system was a little less reliable. Try changing your memory speeds in the same options list to "AUTO" or "200", give one a try because you should be running your memory at either one of these speeds. I assume "200" will give you a more reliable system because it is not workig faster than its rated speed.
Write back and tell me if any of this helped. It took me months of playing around and with my luck, to get this far, and things are working for me. It took a while to know and get a feeling of working with the BIOS to know my system well enough. If its not the hardware, then blame Microsoft .....serisouly though, it could be them and a nice format is needed (sorry to tell you)
MY SPECS:
X-Alien case with 4xx watt power supply...I wanted your case badly but was short on $...and then a week later after ordering the case I had the money..my luck
MSI 865PE NEO2 LS
Pentium4 2.4C ~>2.8 with 233FSB @ 1.55v MAT set to "SLOW"
Corsair TwinX PC3700 512x2 AT 3,4,4,8 @ 2.75v set to "AUTO"
ATI Radeon 9700 non-pro @ 1.5v
Zalman Alum/Copper Heatink/Fan
Santa Cruz sound card
Western Digital Special Edition 120gig hard drive w/ 8meg cache
*AGP/PCI bus frequency should be something like 66/33, greyed out but u can highlight it and change it
**AGP Aperture size get to 64....it should be no higher than 128

BlackScreen and System Reboot with MSI GTX 660 OC TF

Please Svet, or another adm/technnical supporter, I need help!
I have a MSI GTX 660 2gb/ddr5 TF OC s/n 602-V287-04SB1208202249.
I'm having some issues in some games (like Batman Arkham City, Dead Island, Mirror's Edge, Tomb Raider 2013): A few moments after I start to play I just receive a blackscreen, sound bug (like a CD scratched) and the pc reboots.
I already uninstalled the driver with driver sweeper (not in safe mode), reinstalled, installed a old driver and the issue continues. I updated the bios to the NV287MH211 bios. Not helped. I formatted my system too.
I bought another psu, the problem persists.
My system is:
Intel Core i5 3570k 3.4~3.8ghz
Board Gigavyte GA-Z77X-D3H v1.0 (F16 bios)
8gb ram ddr3 kingstom 1333mhz
Psu OCZ ZT550w
Windows 7 64bit
I have a Zotac GTX 460, I tested him and have no problem with the games.
I have no idea what to do anymore.
I will attach a screenshot from bluescreen viewer, the error that appears when I can finish the game without system reboot (ctrl+alt+del) and a log from gpu-z with the moment of the crash.
Thank you for the help, and sorry for my english.
Blue Screen viewer:
Batman crash error:
Gpu-z log:
http://www.mediafire.com/view/?ywskyvjfwyj3ub3
Edit:
I tested Borderlands 2 and after few minutes playing the blackscreen happened, then I just hit ctrl+alt+del, the screen goes white and I listen the sound of disconnected hardware. NVidia Kernel mode sttoped work. I also installed NVidia 320.00 beta driver without solution to the problem.
Apparently, this issue only happens when I play some games that need more gpu use. I'm not sure about this.

Quote from: flobelix on 22-May-13, 02:38:25
Besides you are bumping your thread which is prohibited (>>Please read and comply with the Forum Rules.<<) your addressing one member (in this case even the admin) is bad behavior and will keep others from helping you (as only Svet is asked).
Sorry for that. I don't know everyone in here. I only ask for Svet because another topics that I saw. But in the start of my post I put "or another adm/technical supporter".
I really sorry for that.
Anyway I need help for everyone who can helps me.
Again, sorry for my english too.

System reboots with high CPU load: Advice?

I built this system (in sig) just under a week ago; all works fine. 3 days ago, when running a game (specifically; Dark Age of Camelot, 2x instances == 100% CPU load) the PC rebooted 3 times in a row.
Shortly thereafter, I reinstalled the OS (Win XP Pro SP1 + all windows updates) and the PC continued working fine for about 30 hours, then again began to reboot. At this time I disconnected the 2nd hard drive I had installed.
Just a little bit ago, it again rebooted out of the blue. The system halts, the hard drive spins down and back up, then the system reboots.
This smacks, to me, of a power supply issue. 4 hours of memtest86 resulted in no errors.
CPU is running at 28 degrees idle at the moment, I've seen it go as high as 52 when it's been operating at 100% for several hours without a break. Case temperature is 34 degrees at idle, and I have seen it peak at 42. I don't think temperature is the issue here, but I could be wrong. I have 3 fans in the case, all 80mm- side rear and top mounted; side intake, rear and top exhaust.
Okay anyway... thoughts? I am thinking power supply. I am pretty noobish at this whole business and I get the impression that the PS that came with my case is crapola.

Heh 50+ has always just set off alarm bells in my head. No reason and good to hear that the temps I'm getting are reasonable. I was freaking out that my case's cooling sucked, 'cause I laid the fans out as best I could. What really freaked me out was the Core Center utility that MSI provides, gave some seriously weird temperatures. Now using Motherboard Monitor 5 and it seems to give much more reasonable temps. (Ex: Core Center would report temp at 55c idle, going down to 32c 10 seconds later, then 44 as soon as I moved the mouse.... all over the place. MbM5 seems to provide much more realistic scaling in the temps.)
As for Oklahoma, southwest part a bit up from the texas border- little town called Duncan. It's hot, it's humid, and I've already had to hide in the storm cellar a couple of times from nasty storms. Just moved here 2 months ago after being on the pacific my whole life. :D

.Plist error on system reboot

Similar Messages

Maybe you are looking for