Pls help, flashing gone wrong :(

Could anyone help me, I tried flashing my phone & something went wrong.
Downloaded the french firmware & Flashtool
To be precise, I connected my mobile through usb by pressing vol - , the green light appeared & it showed that my phone is connected in flash mode. After that i pressed thunderbolt button & checked flashmode & popup appeared in which i selected the french firmware i downloaded. I pressed ok. In the main window of flashtool it said loading files to flash, i waited. after two minutes it said device disconnected & said connect your device in flashmode. Then i disconnected my device & re-connected by pressing vol- & its gone. It showed some error while flashing.
Now am unable to switch on my phone nor flashing it again is working Am screwed, can anybody help me ASAP plsssssssssss
The phone does not turn on, the green light appears & a slight vibration when i press the power on button & vanishes in 2 seconds, thats it...
I don't even want ICS anymore, want my mobile working again
Plsssss helpppppppppppp
Solved!
Go to Solution.

I did not check on 32 or 64 bit for flashtools
am using Win 7 32 bit ultimate
I did flash before, but i forgot about USB debugging
My phone is now working fine after the repair through Sony Update Service
thank you arnab, drsanket for your help, deeply appreciated...

Similar Messages

K7T266 Pro 2 Ver 2.0 - Possible flash gone wrong

I have a K7T266 Pro2 Ver 2.0 (as written on the board)
and I recently flashed it with a6593vms.150. Now the computer won't boot.
I've tried clearing the BIOS, no avail.
I've removed the RAM, got three long beeps. Removed the video card, got three long beeps. So it seems that the POST is still being run. BUT, when the sys powers up the 1st D-LED turns green and then it turns Red like all the others. Which seems to indicate a bad proc. I've tested the proc, and it checks out fine. Any other ideas?

Why would you flash BIOS in the first place if it's not broken? And worse you have most probably flashed a WRONG BIOS. This is where you should get your BIOS.
http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=28&NAME=MS-6380%20Ver2.0
You may need to use the BIOS recovery method to flash back to your old BIOS, hopefully you kept a backup for the old one. :P

Flash gone wrong...

Hi all, probably did something stupid here but I'm in need of a point in the right direction.
AMD 2600+
MSI K7N2 Delta-L
1x512 Kingsoton Value Ram KV$400X64C25/512
Saphire Radeon 9600 SE
400W PSU +3.3V/28A | +5V/30A | +12V/11A | -12V/0.8A | +5SB/3A
80 GB Western Digital SE
M6570MS v5.6 110703
Ok, I flashed my bios with a wrong update. Call me stupid, call me whatever but I need a point in the next direction.
I have V6.00 and flashed with an update to V5.6 (6570v56).
When powered on, system will boot and you can enter the BIOS setup. F8 no longer brings up the Boot menu.
If you do not enter the BIOS setup, the screen will turn blank with only a flashing cursor.
The diagnostic LED's on the back freeze on the "TESTING REALTIME CLOCK" combonation.
I cannot forcefully boot from floppy or CD.
I have tried a deep CMOS clear (removed battery, shorted jumpers and unplugged for 45 minutes) and set the FSB jumper to safe mode and I still cannot boot from disk.
Do I need to purchase a new chip?
Thanks,
Nate

Hi,
OK from the info you've just posted. Now this is gonna sound silly! (as your machine worked before the flash), but you look to be woefully underpowered - especially on the +12v Rail it's 11A
A non booting machine can be a classic sign of a lack of sufficient power!
I don't know what they should be for the board your running, but that (11A) is awfully low - recommended is 16A+ (on +12v) for the K7N2 ILSR - and I'm pretty sure the -L should come close.
Read here for more info:
https://forum-en.msi.com/index.php?threadid=31880&sid=
(I suggest you read this in its entirety.)
Also your WD HDD - preferred jumper settings on WD drives are (with no other drives attached to same cable) either No Jumper or Cable select. Weird things can happen if not set correctly (or so I've heard.)
Did you Flash you BIOS for a good reason - if not, you may be able to flash it back to your previous version (if you know what it was) although, I'm not sure about this - other members would though!
I'm gonna have to go now as it's 5.45 in the morning where I am!
If you don't manage to fix your problem start a new thread (or bump this one) listing all hardware being used, your OS, BIOS and short history. There are some good members on this board that aren't here at the moment and may be able to point you in the right direction.
Adjust AGP 8x in BIOS to 4x (you never know it may work.)
RTC - You did put the CMOS battery back in didn't you?
Axel

Firmware flash gone wrong

Hi,
I have the 975X Platinum PowerUp Edition board which uses the Micron® JMB361 chipset.
I needed to flash a sunix PCI card, in order to make it get the it to be used as an IDE card, in my system last night. I used Hirens boot cd and it loaded the drivers for the Jmicron chipset when I booted into DOS. Then when I flashed the card something went wrong and after a couple of screens of garbage it finally said something about Jmicron blah blah blah. Anyway I then booted up my machine and I can use windows fine, but as soon as I transfer data my pc just hangs.
So I was wondering anyone who has the same board can backup there firmware and supply me with the firmware for this Jmicron chipset so that I can reflash it?

I still don't understand what this has to do with JMicron chipset/mainboard at all. The JMicron BIOS is usually updated when you flash your mainboard's BIOS.
What happens if you remove your PCI card?
Quote
fter a couple of screens of garbage it finally said something about Jmicron blah blah blah
It would be good to know what kind of message you actually got. "Something/blah blah blah" doesn't really help, does it?
Quote
as soon as I transfer data
Please be more specific.
Provide full system specs. How many hard drives and optical drives are connected to the system? What ports are they hooked up to?
There are four SATA ports and one IDE port hosted by the Intel ICH7DH Controller and one additional SATA port + a secondary IDE port hosted by the JMicron Controller. If you use only the Intel ports to connect your drives and disable the JMicron Controller in BIOS, do you have problems as well? Please try.

790GX G65 BIOS Flash with M-Flash Gone Wrong

Okay I need some help quickly if anyone has a G65 board. I'm at my friends house and we were updating his BIOS on his G65 board from what I thought was 1.3 to 1.5 with the M-Flash and while the update SEEMED to finish okay, after the restart it failed to POST and load the BIOS. It then starts with the BIOS recovery requested. The problem is its not detecting the USB flash disk with ANY BIOS at all. We've tried 2 different USB Flash Disks and MULTIPLE BIOS IMG files on the Flash Disk and no go. You can see it read the USB Disk, but it doesn't find the BIOS its looking for.
Can anyone tell me with the backup BIOS does it include an extra file or boot IMG to start the process? Also any other sources for 1.44 BIOS? Coolaler seems to be down.

Quote from: Henry on 15-December-09, 14:51:04
Have you read this?:
https://forum-en.msi.com/index.php?topic=119375.0
Yes. It seems as though the boot block has been overwritten or corrupted. CTRL+HOME does nothing. I can't get the board to respond to anything. Its trying to recover the BIOS yet it seems as though the BIOS its looking for on the Flash Disk isn't there. I've put nearly every BIOS file from MSI on the Disk to no avail. I believe the BIOS was 1.3x. I don't know if it was 1.3 or 1.3bx as this is my friends board and we simply checked the version in the BIOS before the flash and it said 1.3.

Adobe Help has gone wrong

I am a relatively naive user of CS5.5. Suddenly, today, when I ask to use the help function for Ai and ID, I get the message:
Adobe AIR: This installation of this application is damaged. Try re-installing or contacting the publisher for assistance.
Re-installing what? Adobe AIR or the whole suite. (why Adobe AIR?)
How do I do it?

Check this link :-
http://helpx.adobe.com/creative-suite/kb/help-application-doesnt-update.html
step by step instruction to fix the issue.

965 Neo flash gone wrong

Hello.
I bought an msi 965F Neo to use with my e6600. I had some Ram problems with the corsair 5400 1gbx2 chips. I upgraded to v1.5 and i had some issues again. I changed my Ram to some kingston chips. The pc wouldn't boot into windows, nor let me setup them again as it freezed always in the same position in the setup.
So i thought it would be better if i downgraded it. I made a bootable disk with the v1.4 bios and used it. The process of downgrading stopped. I don't know if it had finished or not, but the pc stayed there freezed. Now it wouldn't post or anything. Just the lights on the case operate.
Any help?

Ow, please not a Q-Tec again ...
Well, all right:
PEOPLE!!!
Q-TEC PSU
SPOTTED!!!
SAVE YOURSELVES!!!
ftored,
It sadens me to inform you that you bought the most worhless PSU that exists. These things cause nothing but trouble. My advice: take it out of your pc and find a large sledge-hammer and start enjoying yourself...
Really, I've seen too many people with all kind of weird problems and a Q-Tec installed. It's no good at all. They're unstable, bad performers and not safe. I've seen a few boards that were connected to a Q-Tec and were burnt out completely....
Do us and yourself a HUGE favor: Replace your Q-Tec with something good.
NOTE: In case your PSU is made by Q-Technologies, it's not so bad. If it says Q-Tec, it is.

15-d001au bios flash gone wrong .....

hi. after doing a bios update off the hp website, the computer went through the reboot cycle, but it didnt even attempt to restart. just fell to a black screen and has not done a check or anything. i am wondering if this unit is suitable for a win/b key bios restoration or not? everything i have tried as current has failed. what are my options for trying to restore the bios on this laptop? thanks. mangoat

nevermind all, fixed it up with the hp diagnostic software.cheers.

Firefox has suddenly gone wrong. I was successfully running both Firefox and Internet Explorer 8 on Windows 7. I auto-accept upgrades including the most recent Firefox upgrade and the suggested upgrade to Adobe Flash 10.1. But after this, Firefox stopped

Firefox has suddenly gone wrong. I was successfully running both Firefox and Internet Explorer 8 on Windows 7. My laptop is new and has plenty of RAM and HDD. I auto-accept upgrades including the most recent Firefox upgrade and the suggested upgrade to Adobe Flash 10.1. But after this, Firefox stopped working and does not work when I re-load Firefox 3.6. Also IE8 now works very slowly and does not locate major websites like Microsoft without a 'can't find the website message' and having to pressing Return a second time. When I do get to the Mozilla website and click on the button to try to download Firefox 3.6.6, I get this message "Oops! Internet Explorer could not find mozilla3.snt.utwente.nl". Can you help with what has gone wrong? As it stands, I can't use Firefox at all. Note: because Firefox did not work after the upgrade, I've downloaded the IE8 version of the Adobe Flash 10.1. What I really want is to be able to use both Firefox and IE8. But is this possible if they use different versions of Adobe Flash?
== This happened ==
Every time Firefox opened
== About 2-3 days ago ==
== User Agent ==
Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 6.1; Trident/4.0; GTB6.5; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; Media Center PC 6.0; Tablet PC 2.0; .NET4.0C)

I have been having the same problem as the original poster. After upgrading to Ffx 3.6.6, the program asks you to upgrade to Flash Player Plugin 10.1. I download and installed 10.1 only to find videos weren't loading.
In my case, the problem is the previous installation of Flash Player (9.0.47) was somehow messing things up. To fix this, because I already had Flash plugin 10.1 installed I had to uninstall 10.1 using the uninstaller from adobe and then manually remove any files related the old flash player plugin 9.0.47
Here is a run-down of my process:
0. To check if you have a previous installation of the Flash Plugin lurking around, in Firefox go to Tools -> Add-ons -> Plugins (tab). At this point you may seen both Flash plugins.
1. Proceed to uninstall Flash Plugin 10.1. Adobe provides an uninstaller here: http://kb2.adobe.com/cps/141/tn_14157.html
( you have to make sure you have nothing running when you execute the installer).
2. On my Mac (sorry I don't know what it is in Windows) I searched the hard drive for any files/folders with "Shockwave". I found a folder called "Shockwave 10". It wasn't removed by Adobe's uninstaller. For safety I deleted it and then emptied the trash.
3. I then went to My HD -> Library -> Internet Plugins.
Remove the file and folder named "Flash player.old"
4. Restarted; ran the Adobe Flash Player 10.1 installer. Restarted again.
5. Opened up ffx and double checked the plugins list (see step 1). Version 10.1 is installed and available. Went to problem sites to test it out and Success!
Hope this helps.

HT201407 hi..I cant activate my Iphone 5. I bought this from someone who cant remember her apple password and even the email address that she used to set up the account.What am I gonna do now....How can I activate my Iphone. what are my options...pls help

hi..I cant activate my Iphone 5. I bought this from someone who cant remember her apple password and even the email address that she used to set up the account.What am I gonna do now....How can I activate my Iphone. what are my options...pls help me.thank you

Activation Lock in iOS 7 > http://support.apple.com/kb/HT5818
hannibalfromlemery wrote:
.I cant activate my Iphone 5. I bought this from someone
The Apple ID and Password that was Originally used to Activate the iDevice is required.
If you cannot get this information from the seller
Removing a device from a previous owner’s account
You need to return the Device for a refund, as you will not be able to re-activate it.

HT4972 i cant update my iphone 3gs to a more newer ios? it says here error! and the phone flashes some connect to itunes.. an if i connct nothing happens.. help me.. the ipgone wont open . and work pls help me thank you!

i cant update my iphone 3gs to a more newer ios? it says here error! and the phone flashes some connect to itunes.. an if i connct nothing happens.. help me.. the ipgone wont open . and work pls help me thank you!

Hello AlexCornejo,
Thanks for using Apple Support Communities.
The screen you're seeing on your iPhone indicates it is in recovery mode. Now since the device is not appearing in iTunes on your PC, first follow the steps in this article:
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
After following those steps, you should be able to restore your iPhone.
Take care,
Alex H.

Pls, help me , my ipad is disabled as a reult of constant inputing wrong security code by my child on my ipad, i was asked to connect to itunes. The ipad is disabled and cannot do anything to allow me connect to itunes. Pls, What do I do???

Pls, help me , my ipad is disabled as a reult of constant inputing wrong security code by my child on my ipad, i was asked to connect to itunes. The ipad is disabled and cannot do anything to allow me connect to itunes. Pls, What do I do???

This should solve your issue:
http://support.apple.com/kb/HT1212

Safari flash player problem! Pls Help!

Hi, the issue is that if i'm loading a website with a flash player my safari shows me this:
"The page “Electronica / Dance - mp3spy - download mp3” has content of MIME type “application/x-shockwave-flash”, but you don’t have a plug-in installed for this MIME type. A plug-in should be available on this page:
http://www.macromedia.com/shockwave/download/index.cgi?P1ProdVersion=ShockwaveFlash
Do you want to open the page?"
And all the flash adding don't work!! I've tried to install all the falsh plyers and all the staff from the macromedia website, but it is still not working. Thought it was working perfectly before.
Pls help. Any ideas on solving this problem(exept installing again the flash player and rebooting the system)?

This thread may be useful....read ryan m's post about a new "preview" release too - very simple to install this

Pls help, am having problems downloading flash player in windows. keeps asking me to close webplayer

pls help, windows keeps asking me to close webplayer when i try loading flash player

http://forums.adobe.com/message/4041846

Anyone, pls help - my ipad is not opening, only apple logo is flashing on and off... :( pls help

anyone, pls help - my ipad is not opening, only apple logo is flashing on and off... pls help

Have you tried rebooting your iPad?
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.
If that does not work, you can try restoring your iPad iOS Software.
iTunes: Restoring iOS software - Support - Apple
Make sure that you read the article all the way through and pay attention to the last part that talks about using recovery mode.

Pls help, flashing gone wrong :(

Similar Messages

Maybe you are looking for