Plug any USB device on the airport express

I'm trying to connect, instead of a printer, eaither a hard drive or my iPod to the airpot express. Is it possible to do it somehow?

No. The USB port on an AirPort Express is only designed to work with printers, and won't recognize another type of USB device. The 802.11n AirPort Extreme Base Station supports the connection of a hard or flash disk through its USB port.
(22848)

Similar Messages

Other devices to the Airport Express USB

...I want to connect a USB turntable (Project USB III) to the Airport Express USB port. Is it possible to configured USB devices other than printers?

As of now, the only devices supported are printers You would have to hack the firmware of the airport express to get it to connect to anything else. And I wouldn't even know where to start to do that.

Do I need to buy any extra cables for the airport express??

I was wondering if i need to buy any extra cables for the airport exprees.what kind of cables do i have to get to connect the airport express to my DSL modem?

Typically all you would need is an Ethernet cable (cat5, rj45 end), and it would be connected to the LAN port on the DSL modem, and the Ethernet jack on the AP Express.

Is it possible to plug a USB device into the ipad?

I want to use a verizon air card with my ipad, but need to be able to plug it in to a USB port. Is there an adaptation device for the ipad?

No.

HT5211 My HP 2355 won't show up in AirPrint? I have it plugged in via USB and set it up on my Mac mini with the airport express network. Any advice?

My HP 2355 won't show up in AirPrint? I have it plugged in via USB and set it up on my Mac mini with the airport express network. Any advice?

Unless your HP printer is an AirPrint-ready device, just connecting it to the USB port of the AirPort Express base station will not make it so.
On the other hand, connecting a non-AirPrint printer to the base station's USB port it can be shared out by the base station's print server. Please see the following Apple Support article for details.

Can I plug any USB printer that supports AirPrint into the AirPort Express?

I'm interested in getting the new AirPort Express to print from my iPhone. Will any Airprint printer work with my iPhone and iPad?

Hi autefrum,
It sounds like we are confusing AirPrint printers with printers capable of being used with an AirPort Express for wireless printing.
AirPrint capable printers have wireless built in so you can print "directly" from your iPhone, no AirPort Express needed.
The AirPort Express has a USB port to which you connect a "regular" USB printer so you can print to that wirelessly. Effectively, it makes your standard USB printer an AirPrint printer by supplying the wireless connection. So if you have a USB printer already, the AirPort Express may allow you to print to that.
From the spec page, "USB 2.0 port for connecting a USB printer" and "Wireless printing over USB requires a compatible printer and OS X v10.2.7 or later, Windows XP, Windows Vista, or Windows 7.
ivan

Is it possible to plug in an external HDD to the USB connection on my Airport Express for backups?

Is it possible to plug in an external HDD to the USB connection on my Airport Express for backups? As a kind of cheapo Time Capsule?

Unfortunately no, because the USB port on the AirPort Express will only work with a printer and a Keyapan remote control. Hard drives are not supported.
You would need an AirPort Extreme for that type of functionality.

Murder on the Airport Express (AE 1st Gen cannot find Wireless while plugged in in the same room as the modem, router and Time Capsule

First, the reason for my compounded frustration:
I wrote a lengthy, comprehensive post on this late last night. I submitted it and received a notice at this URL:
https://discussions.apple.com/___sbsstatic___/maintenance.html?start=0&tstart=0
It gave a message: "A yellow sticky bearaing the words, "We'll be back soon." and a typed message reading, "We are busy updating Apple Support Communities for you and will be back shortly." Needless to say, it never came back. This morning as I began trying to reconstruct the very detailed post I wrote last night, the Communities system offered me an opportunity to restore the post from last night. Sadly, it contained only a portion of the first line.
I'm going to try it again. The problem inherent in putting it all in words last night, is that I no longer remember the exact wording of the error messages.
I've never gotten this Airport Express (1st gen, purchased mid 2010) to work. I thought it was working, but working poorly. A green light on the device is, apparently, NOT an indication of connection to the wireless. It wasn't workingl.
Description of devices which use the network:
I have a Broadband network with a modem.
It is connecteed to my 2T Timecapsule (purchased mid 2010).
Connected to that is a 24 port Cisco Router.
Not connecting to that, though showing a solid green light, is my Airport Express (1st Generation, purchased mid 2010)
Connected to the router are many ethernet cables giving hard-wired access to:
Printers (HP 8600 Pro purchased 2012))
MacBook Pro (purchased mid 2010) and
IMAC (purchased mid 2010).
3 Apple TV devices (1st generation purchased early 2011)
1 Apple TV device (2nd generataion purchased August 2012)
Connecting to the Wireless Network are IOS devices (current IOS versions on all)
iPad 2nd generation (purchased the day it was available)
iPad 3rd generation (purchased the day it was available)
iPod (mid 2010)
iPhones (4S)
Description of Layout of Network/House
My home is approximately 70 feet by 25 feet.
All Networking hardware is at one end of the house, the south side.
Airport Express (1st Gen, 2010) has been placed in the middle of the house to boost the wireless access at the north end of the house.
Ethernet cables are installed under flooring with cable ends extending up through flooring, and are availble to all devices with Ethernet ports..
Description of Problem
Investigation of the wireless access dysfunction with the iPad (2nd generation, mid 2010) revealed no connection to the Wireless Network, in spite of glowing green light on Airport Express and Airport Utility screen.
Description of actions taken to correct the problem
Loaded Airport Utility on MacBook Pro.
Airport Express shows green light on screen.
Double clicked on Airport Express Icon
Message that Airport Express was unable to extend the network
Message changes suddenly to something about not finding the Airport Express
Airport Utility searches Airport Express, attempting to read its settings
Message appears: Device not found. Airiport Express was previously part of the network, and offers to let me "forget" the base station.
I exit the error message.
A yellow triangle bearing an exclamation point sits to the left of the Airport Express' Description
Airport Express shows green light (as always)
Clicking the link, "Other AirPort Base Stations" indicates no base stations can be found.
Moved Airport Express to the room at the south end of the house containing all network devices
Plugged it in with clear, completely unobstructed view of Time Capsule.
Light on Airport Express flashes yellow and then turns solid green (like always)
Bring Mac into the room at the south end of the house containing all network devices and the Airport Express with the green light
Close Airport Utility on Mac
Reboot Mac
Open Airport Utility on Mac
Airport Express still shows as it did in 1.1.7. above.
Attempts to check Airport Express' access to Wireless network:
Unplugged Airport Express HEY! THE GREEN LIGHT WENT OUT!!! ;0)
Disconnected all Ethernet cables.
Tested ALL devices for Wireless access.
All devices access the Wireless network extremely well (dot and three curved bars) EXCEPT
IOS Devices tested at the north end of the house. These devices show a blank where the wireless bars should be, and intermittently show a dot.
Followed instructions contained in a similar discussion about Airport Express not functioning:
Unplugged all Networking Hardware
Powered off all Equipment which access the Internet in any possible way.
Powered up all Networking Hardware, one at a time, in the order described in that discussion.
Powered up all Equipment which access the internet, one at a time.
Tested ethernet cablingAll equipment functioning.
Tested Wireless access:
Removed all ethernet cabling
All devices, including IOS devices, access the Wireless Network perfectly EXCEPT any placed in the north end of the house. Those perform exactly as they did in step 3.3.2.
Connected all ethernet cabling.
Plugged Airport Express into socket in the Network Hardware room at the south end of the house. I get exactlyt the same results as before. The lovely green light glows on the Airport Express. Airport Utility reports Airport Express cannot find the Wireless network and also says there are no base stations connected to the internet.
Still in Network Hardware room, I attempt to find other base stations by cabling the Airport Express to the MacBook Pro
Airport Utility shows Airport Express with a green light
I double click the Airport Express Icon
Box says connection is average and status is (green light) Extended Network.
I click Edit
I go through each tab. I note that in the Wireless tab, the Network Mode is as I had set it, "Extend a wireless network".
Under the Network tab I note that "Enable Access Control" is as it should be, NOT selected.
Under the AirPlay tab, I note that "Enable airPlay" is selected.
I click cancel and leave the Edit screens.
Curious to know if Airport Express can find the Wireless network now that the device claims to be functioning as an extended wireless network, I disconnect the ethernet cable from the Airport Express.
I watch the Airport Utility screen closely. Nothing is happening.
With bated breath, I double click on the Airport Express icon.
The popup box shows "extended wireless network"
I click on edit and we start the whole mess over again. (See 1.1-9. above)
Curious to know if cabling the Airport Express to the iMac (almost to middle of house) will offer hope and prosperity to IOS devices at north end, I unplug the Airport Express and carry its now-exhausted little body to the iMac, ethernet cable in hand.
As I unplug the iMac from its ethernet access, I'm informed by Cranky Boy that no way is he going to accept that as a reasonable solution to his problem. He will not live wireless while even one ethernet cable is poking up through a floorboard.
Cranky Boy is reassured when informed that, though the Airport Utility shows the Airport Express connected, merely double clicking on the icon produces the same result as laboriously described in 1.1-9. above.
After quieting Cranky Boy by reconnecting the iMac to the Ethernet, I return the Airport Express to the Network Hardware room.
Again, curious to know ... I reconnect the Airport Express to the MacBook Pro. I want to know if it will exrtend the Wireless network from its position one foot from the Wireless Network.
I close and reopen Airport Utility (as I always do, but forgot to write)
I click on the Airport Express icon (which bears a little green light like the other big boys).
BUT THIS TIME, when I click on the Airport Express icon, the pop-up box says my connection is Excellent, the green light status shows, "Extended Network" and clicking on "Extended Network" produces the same old `Airport Express was unable to extend the Wireless Connection.
I click on the Edit option.
I buzz through all the tabs. I cancel instead of update, leaving everything as it was (as I did the first time)
I decide to go back into edit and select "Internet Options" under the "Internet" tab.
Since I have no idea whatsoever as to what IPV6 is and what it governs, I decide to configure IPV6 to Automatically Connect and then, with a whole new set of opportunities, I leave IPV6 Mode set to "Tunnel" and then I learn that I will get to see what happens when "Enable IPV6 Connection Sharing" is enabled.
I check the other tabs to see if anything has changed in their menus
Jesus Saves and so did I.
Apple updates and so did I.
I am warned that my device and its network services will be temporarily unavailable if I continue.
It seems unaware that I am laughing uncontrollably at the suggestion that my device and its services will be TEMPORARILY AVAILABLE. What? An improvement in performance is warned?
Life continues and so do I.
I breathe deeply to decrease my adrenaline.
Airport Utility flashes a red warning next to the Airport Express Icon and then quickly rethinks the matter and decides to show it as connected.
I click on the Airport Express Icon. This time my connection is only "good".
I click on Extended Network. With a new-found consistency it informs me that my device is unable to extend the Wireless network and it chats with me about using the same Wireless password for my device that is used for the Wireless network access. I did. It is.
I change my settings back to the way they once were, I save like Jesus and Update like Apple
I decide to go back into Edit and modify the settings under the Wireless tab, changing from "Extend Wireless Network" to "Join Wireless Network".
I save.
I click on the Airport Express Icon. My connection has degraded further to "Average"
I click on edit just to see what will happen, but no further information is forthcoming. Settings are as I left them.
I wonder if the Airport Express would extend itself now that it has joined the Wireless Network.
I click the Airport Express Icon.
I click Edit
I change the Network Mode from "Join a Wireless Network" to Extend a Wireless Network. Unfortunately, there was no option for "don't forget where the Wireless Network is!"
I am still "unable to extend the Wireless network"
I disconnect the Airport Express from my MacBook Pro.
After closing and opening Airport Utility, I sit and stare at the Airport Express Icon.
It has no light or error messages
It has a yellow triangle with exclamation point
It has no light or error message
It has a yellow triangle with exclamation point
I finally decide to see what THIS error messages says. It says Device Not Found. Patti Harada's AirPort Express was previously part of your network. Check that it is still in range of your network and is plugged into a power outlet. Click Forget to remove this base station from this network."
I click "Forget". Airport Utility has forgotten the Airport Express ever existed. It has also forgotten how to find it again.
I, however, am unable to forget how much I shelled out for this POS and fear I will never recover from working this intensely and tediously on documenting something so hideously inconsistent in its test results.
I wonder if I should recable the Airport Express to my MacBook Pro
I decide I've had about enough.
I document this ad nauseum in the hopes that someone can read it THOROUGHLY and offer me a solution to my problem. What is my problem? I am so busy fighting off Alligators that I forgot I only came in to drain the swamp! Ah, but I remember now: Cranky Boy can't watch Netflix on his iPad (2nd generation) in the north end of the house.
Any solution that works will do. I'll buy another piece of whatever kind of equipment you think best.

Well, aren't you all that and a bag of chips!!!!
Oh what a relief! What a RELIEF!
That just cleaned up my life. And Cranky Boy is actually smiling!!!
Houston, we've got dots AND BARS!!!
P.S. All my firware and software are always current. If I spent as much time looking for a reset button as I spend checking for software updates, I mighta not needed to work at this!!!!
P.P.S. Airport Utility shows Cranky Boy's iPad as the Airport Express' Wireless Client!!! Who knew?
Thank you so much, m'Lord. I am in your debt. What would you have me do?
Patti in Tucson AZ

I can use a modem 3G in the AirPort express, put it in gate USB of the equipamentos?

I can use a modem 3G in the AirPort express, put it in gate USB of the equipamentos?

No. The USB port on the AirPort Express is designed to be used only for a USB printer.

Has anyone ever plugged into the airport express to get online?

Want to plug my xbox 360 into the airport express to get online so I don't have to move anything around.
Right now my modem & router is in bedroom, & the airport express is in the living room (w/xbox and speakers) to extend wireless signal and throw music to speakers in living room.
I can move it, just lazy and then won't be able to use speakers, and don't want to buy xbox wireless adapter.....
It's already a bridge, it would make sense that I could plug in? maybe not ;}
airport express/ aluminum powerbook g4 Mac OS X (10.4.8)

If you have the AirPort Express Base Station (AX) set up as a remote base station in a WDS configuration, then, yes, you can connect the Xbox 360 to the AX's Ethernet port for Internet connectivity. If it's setup as a wireless client, then no.

Can the Airport Express connect wirelessly to a current modem and be the wireless connection for an external??

I'm confused, I purchased the Airport Express and GDrive external hard drive at the Apple store. I already own a wireless modem that works fine (AT&T). I want to extend the wireless signal to the downstairs where the office is and keep the Airport Express in the office (connected wirelessly to the modem upstairs) plugged into the new GDrive to make that wireless. I want the G Drive in the safe location of the office and that was the sole reason I purchased the Airport Express. Is it possible??

As I said, the USB port on the AirPort Express will not support a hard drive. It will only support compatible printers.
If you want to connect a hard drive, you will need an AirPort Extreme.....not an AirPort Express. See this Apple comparison chart to confirm. Might be a good idea to print it out and take it to the "genius" types.
Compare Apple Wi-Fi base stations AirPort Express AirPort Extreme Time Capsule
But, even if you have an AirPort Extreme the chances that it would "extend" the wireless signal from an ATT router are about zero.

When I plug in external hard drive to airport express it tells me not enough power for the usb port. I have the airport express plugged in to power

Airport express tells me not enough power to usb port for hard drive.
I do have power to Airport express plugged in.

The AirPort Express will not support a hard drive....only a printer.
If you need to connect a hard drive, you need an AirPort Extreme, not an AirPort Express.

I was told at the Apple store that I could simply plug in ( electric power) the Airport Express and it would find my wireless network. I hoped to use it as a way to play music from my iphone. I do not use other Apple routers etc,

The Airport Express is not finding my wireless network. I do not have any of the devices listed below. I have a Belkin wireless router. Can I still use Airport Express ( without plugging an ethernet cable into it) ? Any ideas for how to make it find my network ? It is sitting next to the wireless router-so is in range.
If you already have a wireless network in your home and want to extend its range, AirPort Express can help. Just place it in range of your primary base station — an AirPort Extreme, Time Capsule, or another AirPort Express — and near the area where you want your wireless connection. Launch the easy-to-use AirPort Utility app on your iOS device or Mac, and you’re mere minutes away from long-range Wi-Fi enjoyment.

Hi - you can do what you want to do with AirPlay from your iPhone - but unfortunately it is not as easy as the people in the Apple store told you - your first problem is that you have a non Apple router - you cannot extend a non Apple router wirelessly with the Express - you can only join the network and connect an ethernet device to it - you can however connect via ethernet and have it create a wireless network of its' own - you can set this up from your iPhone or the XP - but this is a complicated setup and would involve many different discussion areas of this forum - therefore I would suggest that you use your 90 days of support and consult directly with Apple to do this - go to this link - http://www.apple.com/support/contact/

HT1515 I want to extend my existing wireless router upstairs to my new smart TV. I have loaded the AirPort Express onto my desktop Mac. In simple terms do I now just plug the AirPort into a socket halfway between the base WiFi and the Smart TV, or do I

I want to extend my existing wireless router by using the AirPort Express for my Smart TV. Can I just plug in the AirPort halfway between the router and the Smart TV and have no direct connection to a computer or the TV, or do I need to plug in next to the TV and somehow connect the AirPort to the TV (ethernet)?

You are asking several different questions. If you need to store your photos, music, and movies on an external volume, you certainly can. Any externally connected hard disk drive will work, connected either directly to your Mac or to your Time Capsule as a shared volume.
You should not rely upon using that as a backup device though. Although you certainly may use it for both purposes, it is a better idea to have dedicated backup devices for a variety of reasons not limited to redundancy. You would not want to simultaneously lose all your pictures as well as your backup. If they are all on the same device, that could happen. Furthermore, a backup cannot back up the volume on which it is running.
As for adding an Extreme or Express, using its LAN port for your iMac, and then enable Internet sharing so you can effectively use the iMac as a "hotspot", you can do that too, but I am unclear on what benefit you believe this arrangement would convey for you.
An Extreme's Guest network is separate from its Main network; that is the reason for having it.

I have both Apple and Android devices. My Android devices will not stay connected to wireless . I have the Airport Express. The Android devices are a Galaxy S4 and Tab 3. These both worked perfectly on my ancient Linksys WRT 120 N wireless router.

I have called Apple support twice and no one can confrm or deny as to whether Android devices can connect with the Airport Express. I have had the it configured 3 times so far and my Galaxy S4 and Galaxy Tab 3 7.0 are useless with the Airport Express.

BTW what did you mean by using my old wireless router as a AP?
Every Wireless router ever made is actually made of two components..
A router and a wireless AP. (AP = Access Point).
To use any wireless router as a AP you simply bypass or turn off the router..
In an Apple router this is called Bridge mode..
In many routers it is known as AP or WAP mode.
But often they do not have the option..
Set it up manually.. we call this WAN bypass as it will bypass the router.
So what you do is open your wireless router setup page in your browser.. go to the LAN setup page.
You need to do two things.
1. Turn off the dhcp server.
2. Set the LAN IP to match the main router..
For instance if your plug it into your apple router and it is at the default IP.. 10.0.1.1 then set the Linksys to 10.0.1.254
The Linksys is then updated.. Plug the ethernet cable from LAN port apple router to LAN port WRT120 (not WAN)
Now with a computer plugged into the apple router or into the Linksys .. by ethernet.. open the IP address you just set.. go to the wireless tab in the setup and give the wireless SSID a suitable name for your other (non-apple) products.. voila.. you have now turned a wireless router into an AP.

Plug any USB device on the airport express

Similar Messages

Maybe you are looking for