Plymouth causes tty1 to tty6 to hang during boot

Hello,
During the boot process of my Arch installation the screen is halted at terminal login and password, where I previously had configured Arch to automatically start X. Now, I've also noticed that tty2 to tty6 are not available in the beginning and then every 10 seconds one extra comes available. The cause, has something to do with Plymouth.
I installed Plymmouth, but failed to get it running. Then I inunstalled, removed the hooks from /etc/
mkinitcpio.conf. Also rebuilt initrd image, but somehow Plymouth still tries to start. I've added a bootlog in which the problem is very clearly reported (from line 163 or so). (I'm not sure how to post, so I just post the link to pastebin)
How can I solve this problem?
http://pastebin.com/FR6AW7Ak
Last edited by Archer22 (2014-09-23 07:52:57)

jasonwryan wrote:
Please read the Etiquette entry on how to post (https://wiki.archlinux.org/index.php/Fo … ow_to_Post): note the one topic per thread to make things manageable.
Are you sure that you removed plymouth from your initrd?
Not a Sysadmin issue, moving to NC...
I edited my post. Yes I think removed Plymouth from initrd through the following command:
# mkinitcpio -p linux
Is there anyway I can check? Also, I was thinking maybe the fallback image is used, where plymouth is still configured to start?

Similar Messages

K8N Neo 2 Platinum -- Hanging during boot --RESOLVED--

Heres the problem...
My system will hang during boot at anytime, from bios initalization to full windows boot (No BSOD ever and where the pc hangs in the boot proccess is totally random). And the only way to get past the hang is do a soft reset. I have to restart my system up to 3 times before I get a good boot, but once the pc is up and running, it stay running till I shut it down. (no hangs)
Now if I shut it down after the system has been running for a while, the pc will restart normally without any hangs. The hangs only occur after the pc has been down for a time.
I have reseated all the connectors, the memory (even tried different slots), add-in cards, cpu.
I have a clean install of Windows XP Pro (hard drives have been repartitioned and reformatted as NTFS)
All fans are spinning up fine, all temps are within norm, power supply voltages are within norm.
No phsysical signs of bad caps on the system board.
I ran ran Memtest86 for 18 hours striaght with no errors.
Ran CPU stress test with no problems.
No IRQ,DMA,etc conflicts found.
Windows records no errors during a freeze and I have checked for unwanted services/proccess as well.
I have tried min install to no avail.
Bois is retaining its settings (so bios battery is good)
I do not over clock anything. Bios is set to discover all important setting automaticly. (Bios setting are the same now as they were 6 months ago)
I am down to a possible cold solder joint on the system board?
This problem started to occur about a month ago.
If someone has seen this exact problem and has a resolution, well I would appreciate it if you passed along your knowladge
I am down to my last option of RMAing my system board. No. I have not replaced any components due to the fact I don't have extras lieing around nor can I spend the money just to troubleshoot :(
Specs..
Athlon 64 3500+
2 gig (pqi TURBO 1GB 184-Pin DDR SDRAM DDR 400 (PC 3200) Unbuffered System Memory Model PQI3200-1024SB) Ran in Dual config
Geforce 6800 (BFG 6800 GT oc)
Creative X-Fi XtremeMusic
Antec NeoPower 480
2 WD 36gig SATA Raptors in raid 0 (system partition)
2 WD 120gig IDE in raid 0 (data partition)
Windows XP Pro
all drivers and bios are manufacture ref and up-to-date.
Ok I won't go into all the details of why I missed this but it turns out the northbridge heatsink fan had stopped spinning and thus the hangs during boot due to overheating (hhmmm, when I step back and look at this the symptoms point right to overheating).
This also expains why after several attempts at booting up, once the pc was up it would run like a champ. The chip would of course overheat and cause random freezes. Now due to the placement of the chip and the design of the heatsink once there was enough airflow over the heatsink the chip would remain cool enough to prevent further freezing of the system.
What helped to facilitate this is that I have a ducted fan system installed in the bottom of my case which directs a substantal amount of fresh air to the pci slots, the chip set and the AGI slot as well.
So what have we learned class?
1. check the obvious
2. do a complete physical inspection of your system
3. KISS -- keep it simple stupid

Is this your ram:
Quote
Part Number: PQI3200-1024SB
Quality Control: Comprehensively and rigorously tested
Package: 1024MB single pack
Organization: 128M x 64-bit
CAS Latency: 3-4-4-8
Test Voltage: 2.6 V
PCB Board: 8 Layers PCB
Heat Spreader: Mirrored Black Copper
Speed: DDR 400 MHz (PC3200)
Type: 184-pin DDR SDRAM
Error Checking: Non-ECC
Registered/Unbuffered: Unbuffered
Warranty: Lifetime
This is a quote from MSI web site:
Quote
Main Memory
• Supports dual channel DDR 266/333/400, using four 184-pin DDR DIMMs.
• Supports the memory size up to 4GB
• Supports 2.5v DDR SDRAM DIMM
Due to the High Performance Memory design, motherboards or system configurations may or may not operate smoothly at the JEDEC (Joint Electron Device Engineering Council) standard settings (BIOS Default on the motherboard) such as DDR voltage, memory speeds and memory timing. Please confirm and adjust your memory setting in the BIOS accordingly for better system stability.
Example: Kingston HyperX DDR500 PC4000 operates at 2.65V, 3-4-4-8, CL=3.
For more information about specification of high performance memory modules, please check with your Memory Manufactures for more details.
Manually adjust your ram voltage to 2.65 volts and then manually adjust your ram timings to 3-4-4-8-2T.
If that does not work then do as Richard suggested and strip down to a bar-bone system, this is CPU+fan, 1 stick of ram (try other stick and different slots as one may be bad), graphic card and PS-2 keyboard, if it boots fine without any problems then add one device at a time until you find the problem.
Post back results as there are more things one can try but lets start with the simple stuff and work up.

Ultra 5 Hangs During Boot

My Ultra 5 hangs during boot at the following point....
setting default ipv4 interface......
I have tried resetting my router, unplugging the network cable, and nothing seems to work.
John

jmorrissey3, is this a system that just suddenly stopped working, or is this a "new" system (it's not like Ultra 5s are really new) that you're trying to bring up?
If this is a new system for you to tinker with, you should just go ahead and reinstall the operating system. This will blow everything away, of course, but it's good experience if you've never done it before and it will guarantee that the system is clean.
If the data on there must be retained, you can boot from CD-ROM, mount the / partition, and look at some of the configuration files to try to isolate the problem. I would agree that it either is set up for DHCP and there is no DHCP server or there is an invalid NFS mount that is trying to take place.

P205-s6237 Hangs during boot to recovery after replace HDD

I replaced a bad HDD and the machine hangs during boot to the recovery disk. it gets past the inspecting screen and then hangs when the VISTA dots appear. the dots continue to scroll left to right but nothing ever happens. Any ideads on getting it past this point?

I replaced a bad HDD and the machine hangs during boot to the recovery disk. it gets past the inspecting screen and then hangs when the VISTA dots appear. the dots continue to scroll left to right but nothing ever happens. Any ideads on getting it past this point?

Arch Live CD x64 hanging during boot at "triggering uevents"

Hello!
I recently was recommended Arch by a friend, and after I followed the 'Newbies Guide' and burning a live CD to install Arch with, it appears to hang during Live CD boot at "installing uevents."
I am trying to install Arch as a dual boot on a late 2008 MacBook Pro which is currently running x64 Windows 7. I have plenty of HD space (100gb free and 100gb unallocated to install Arch onto).
Here is a picture:
http://i.imgur.com/Y8P41nf.jpg
I get the same error weather I try to install x64 or i686 (I think that's what it's called). Is there any reason for this?
Thank you!
-- mod edit: read the Forum Etiquette and only post thumbnails http://wiki.archlinux.org/index.php/For … s_and_Code --
(Sorry, missed that. My bad!)
Last edited by RalphORama (2013-09-07 03:09:13)

frank604 wrote:
You can try nomodeset. Seems to be a failure in loading a driver for your hardware. To read more on similar issues, there's a few posts with more info and suggestions by googling it.
Google result: http://lmgtfy.com/?q=halt+at+triggering+uevent
Results:
https://bbs.archlinux.org/viewtopic.php?id=151259
https://bbs.archlinux.org/viewtopic.php?id=140426
Thanks! I tried googling it myself but got mostly answers that didn't work. I'll try this!

Mac Mini keeps hanging during boot

My ~3 year old Mac Mini keeps freezing during booting with the error message "You need to restart your computer. Hold down the Power button...". This happens every time. Booting in safe mode works.
This happened with Mac OS X Tiger but keeps happening even after I have completely reformatted that hard disk and reinstalled Leopard from scratch. There are no external devices connected to the computer besides the monitor and a bluetooth mouse and keyboard.
After reading some discussion forums I have already tried starting into Open Bootware and running "reset-nvram" and "reset-all" but to no avail.

Welcome to Apple Discussions!
What you are suffering is a Kernel Panic, and given you have reformatted your drive and reinstalled MacOS, it would tend to suggest the issue is hardware related - most common culprit being RAM.
http://docs.info.apple.com/article.html?artnum=106227 explains what kernel panics are, and http://www.thexlab.com/faqs/kernelpanics.html and http://www.index-site.com/kernelpanic.html may give some assistance in working through the problem to determine the cause.
The one good thing is that your system appears sufficiently stable to allow you to boot to the Leopard installer and complete a full install. This makes it less likely there is a fundamental issue with the most expensive component of the system, the logic board.

Multiple cPCI Graphics cards - System Hangs during Boot

We have 2 Kontron dual output CP332 cPCI graphics cards to install into a NI PXI rack in order to give us 4 graphics outputs.
When one card is installed it acts as the Primary graphics card and it is required to disable to NI on-board graphics card in order for this to boot and function correctley.
If a 2nd Kontron CP322 card is added the system will hang during WinXP boot, as it switches from VGA to SVGA mode.
Disabling the 2nd card via device manager allows the system to boot.
Re-enabling the 2nd card once booted, then configuring with the ATI driver application allows the 4 graphics output to work as expected.
If the system is re-powered it will once again hang during WinXp booting.
Is there anything that can be configured on the NI Embedded PC (BIOS) to prevent this ?
Is there anything in windows that can be set to prevent this ?
Can we control the windows device manager from labview in order to enable/disable the 2nd card after power-on and before shutdown.
many thanks

Hi Scott,
I have some more information for you regarding your issue. We have tested the Kontron CP332 with the PXI-8196.
However when we tested the setup, we had 3 monitors working, the on-board graphics and the dual output from the card.
Until we get the on-board graphics working with a single CP332 I don't think we will get bot CP332's working.
So these are the steps to get on-board graphics working with a single Kontron card the steps come from talking to our PXI Product Support Engineer:
"The first thing you need to make sure is that you are using the
driver for Windows XP, and not the one for Windows 2000. Here's a link
to the driver download page:
http://us.kontron.com/index.php?searchword=cp+332&id=363
Notice that the first two driver downloads look just the same, but if
you hover over them and look at the url, you'll notice that the first
one is for Windows 2000 (w2k), and the second one is for Windows XP
(wxp). So, just make sure you are using the second one. The PSE did
mention that she was initially using the Win 2k driver, and was having
some issues with it hanging and all. Here's the information she sent me
about how she was able to get things working:
"Here is the info. My controller has BIOS version 1.3 but have him try this first before updating the BIOS.
The Kontron Board is the CP 332. I was able to get all three monitors working with the PXI-8196.
Configuration steps:
1) Insert both the controller and the kontron board in the chassis.
Note: When the computer is starting it will give you the Windows boot
up screen on the DVI 1 on the Kontron board and then give you the login
screen on the monitor connected to the 8196 so make sure you still have
a monitor connected to the controller.
2) Cancel the NI installation wizard if it comes up.
3)
Unzip the drivers and run the setup.exe file. Make sure you install
both the ATI display driver and the ATI Control Panel. (Check the zip
name to make sure you have the xp version of the driver)
4) After
restart go to the Display Properties and under the Settings tab you
should have monitors 1 and 2 on Mobility Radeon 9000 (Kontron CP-332)."
If you don't have BIOS version 1.20 or higher, please upgrade to BIOS version 1.30, if you need to upgrade the BIOS please make sure you fully understand the readme file. Then follow the steps above to enable triple output on the graphics cards.
When you have this working please try adding the second Kontron card.
Regards
JamesC
NIUK and Ireland

Hangs during boot after upgrading to Kernel 2.6.39

I have just installed Arch on a new computer. It works fine until I upgrade to Kernel 2.6.39. After that it hangs on boot.
The end of /var/log/everything.log is posted below.
Jul 26 23:52:06 localhost kernel: [ 6.036766] [drm] nouveau 0000:04:00.0: Parsing VBIOS init table at offset 0x85F3
Jul 26 23:52:06 localhost kernel: [ 6.129046] adt7475 1-002e: ADT7473 device, revision 1
Jul 26 23:52:06 localhost kernel: [ 6.138997] [drm] nouveau 0000:04:00.0: Detected monitoring device: adt7473
Jul 26 23:52:06 localhost kernel: [ 6.139000] [drm] nouveau 0000:04:00.0: 1 available performance level(s)
Jul 26 23:52:06 localhost kernel: [ 6.139002] [drm] nouveau 0000:04:00.0: 0: memory 405MHz core 270MHz shader 540MHz
Jul 26 23:52:06 localhost kernel: [ 6.139233] [TTM] Zone kernel: Available graphics memory: 12371030 kiB.
Jul 26 23:52:06 localhost kernel: [ 6.139236] [TTM] Zone dma32: Available graphics memory: 2097152 kiB.
Jul 26 23:52:06 localhost kernel: [ 6.139238] [TTM] Initializing pool allocator.
Jul 26 23:52:06 localhost kernel: [ 6.139252] [drm] nouveau 0000:04:00.0: Detected 5376MiB VRAM
Jul 26 23:52:06 localhost kernel: [ 6.139260] mtrr: type mismatch for d0000000,8000000 old: write-back new: write-combining
Jul 26 23:52:06 localhost kernel: [ 6.150626] [drm] nouveau 0000:04:00.0: 512 MiB GART (aperture)
Jul 26 23:52:06 localhost kernel: [ 6.152371] [drm] nouveau 0000:04:00.0: failed to load fuc409d
Jul 26 23:52:06 localhost kernel: [ 6.176193] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
Jul 26 23:52:06 localhost kernel: [ 6.176195] [drm] No driver support for vblank timestamp query.
Jul 26 23:52:06 localhost kernel: [ 6.228800] No connectors reported connected with modes
Jul 26 23:52:06 localhost kernel: [ 6.228802] [drm] Cannot find any crtc or sizes - going 1024x768
Jul 26 23:52:06 localhost kernel: [ 6.231002] [drm] nouveau 0000:04:00.0: allocated 1024x768 fb: 0x8020000, bo ffff880608d97800
Jul 26 23:52:06 localhost kernel: [ 6.233786] Console: switching to colour frame buffer device 128x48
Jul 26 23:52:06 localhost kernel: [ 6.235094] fb0: nouveaufb frame buffer device
Jul 26 23:52:06 localhost kernel: [ 6.235094] drm: registered panic notifier
Jul 26 23:52:06 localhost kernel: [ 6.235098] [drm] Initialized nouveau 0.0.16 20090420 for 0000:04:00.0 on minor 0
Jul 26 23:52:06 localhost kernel: [ 6.255449] HDA Intel 0000:04:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
Jul 26 23:52:06 localhost kernel: [ 6.255451] hda_intel: Disable MSI for Nvidia chipset
Jul 26 23:52:06 localhost kernel: [ 6.255599] HDA Intel 0000:04:00.1: setting latency timer to 64
Jul 26 23:52:06 localhost kernel: [ 7.663482] EXT4-fs (sda3): re-mounted. Opts: (null)
Jul 26 23:52:06 localhost kernel: [ 7.807508] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
Jul 26 23:52:06 localhost kernel: [ 7.851401] Adding 265068k swap on /dev/sda2. Priority:-1 extents:1 across:265068k
Jul 26 23:52:06 localhost kernel: [ 8.569682] r8169 0000:08:00.0: eth0: link down
Jul 26 23:52:06 localhost kernel: [ 8.569687] r8169 0000:08:00.0: eth0: link down
Jul 26 23:52:06 localhost dhcpcd[747]: eth0: waiting for carrier
Jul 26 23:52:08 localhost dhcpcd[747]: eth0: carrier acquired
Jul 26 23:52:08 localhost kernel: [ 10.301736] r8169 0000:08:00.0: eth0: link up
Jul 26 23:52:08 localhost dhcpcd[747]: eth0: broadcasting for a lease
Jul 26 23:52:12 localhost dhcpcd[747]: eth0: offered 131.181.53.42 from 131.181.127.32
Jul 26 23:52:13 localhost dhcpcd[747]: eth0: acknowledged 131.181.53.42 from 131.181.59.48
Jul 26 23:52:13 localhost dhcpcd[747]: eth0: checking for 131.181.53.42
Jul 26 23:52:18 localhost dhcpcd[747]: eth0: leased 131.181.53.42 for 43200 seconds
Jul 26 23:52:18 localhost dhcpcd[747]: forked to background, child pid 774
Jul 26 23:52:18 localhost crond[823]: /usr/sbin/crond 4.5 dillon's cron daemon, started with loglevel info
Jul 26 23:53:01 localhost crond[823]: FILE /etc/cron.d/prune-cronstamps USER root PID 835 job prune-cronstamps
Jul 26 23:53:01 localhost crond[823]: FILE /var/spool/cron/root USER root PID 836 job sys-hourly
Jul 26 23:53:01 localhost crond[823]: FILE /var/spool/cron/root USER root PID 837 job sys-daily
Jul 26 23:53:01 localhost crond[823]: FILE /var/spool/cron/root USER root PID 838 job sys-weekly
Any help fixing this would be greatly appreciated.

I have been trying to isolate the problem a little further. I re-installed (with just the base and sudo) and after upgrading pacman rebooted and it worked without fail. Then I installed libusb and libusb-compat which where required when I tried to upgrade just the kernel using
pacman -S kernel26
which initially failed because of the missing dependencies libusb and libusb-compat. I then re-booted and that worked without a problem.
I then upgraded to Kernel 2.6.39 using the above command and then it hung on rebooting. I saved the logs at each stage.
The additional logs in errors.log in the reboot that failed are as follows.
ul 26 16:28:39 O313 kernel: [ 5.120698] [drm] nouveau 0000:04:00.0: Pointer to BIT loadval table invalid
Jul 26 16:28:39 O313 kernel: [ 5.360508] [drm] nouveau 0000:04:00.0: failed to load fuc409d
Jul 26 16:28:39 O313 kernel: [ 5.808016] sd 20:0:0:0: [sdb] Assuming drive cache: write through
Jul 26 16:28:39 O313 kernel: [ 5.809960] sd 20:0:0:0: [sdb] Assuming drive cache: write through
Jul 26 16:28:39 O313 kernel: [ 5.812116] sd 20:0:0:0: [sdb] Assuming drive cache: write through
Jul 26 16:28:35 O313 udevd[369]: error: runtime directory '/run/udev' not writable, for now falling back to '/dev/.udev'
The end of kernel.log is as follows:
Sat Jul 9 14:57:41 CEST 2011
Jul 26 16:28:39 O313 kernel: [ 0.000000] Command line: root=/dev/disk/by-uuid/e4733c60-3e54-4001-a83e-415b690dfcb0 ro
Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-provided physical RAM map:
Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 0000000000100000 - 00000000cfed0000 (usable)
Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 00000000cfed0000 - 00000000cfed1000 (ACPI NVS)
Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 00000000cfed1000 - 00000000cfee0000 (ACPI data)
Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 00000000cfee0000 - 00000000cff00000 (reserved)
Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 0000000100000000 - 0000000630000000 (usable)
Jul 26 16:28:39 O313 kernel: [ 0.000000] NX (Execute Disable) protection: active
Jul 26 16:28:39 O313 kernel: [ 0.000000] DMI 2.4 present.
Jul 26 16:28:39 O313 kernel: [ 0.000000] DMI: Gigabyte Technology Co., Ltd. X58A-UD5/X58A-UD5, BIOS FD 02/01/2011
Jul 26 16:28:39 O313 kernel: [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
Jul 26 16:28:39 O313 kernel: [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
Jul 26 16:28:39 O313 kernel: [ 0.000000] No AGP bridge found
Jul 26 16:28:39 O313 kernel: [ 0.000000] last_pfn = 0x630000 max_arch_pfn = 0x400000000
And this is the end of daemon.log
Jul 26 16:27:49 O313 init: Switching to runlevel: 6
Jul 26 16:27:50 O313 dhcpcd: received SIGTERM, stopping
Jul 26 16:27:50 O313 dhcpcd: eth0: removing interface
Jul 26 16:28:39 O313 2.352592] udevd[87]: starting version 171
Jul 26 16:28:39 O313 4.531007] udevd[370]: starting version 171
Jul 26 16:28:39 O313 dhcpcd: version 5.2.2 starting
Jul 26 16:28:39 O313 dhcpcd: eth0: waiting for carrier
Jul 26 16:28:35 O313 udevd[369]: error: runtime directory '/run/udev' not writable, for now falling back to '/dev/.udev'
Jul 26 16:28:39 O313 init: Entering runlevel: 3
Please let me know if any further information would be useful in tracking down this problem. Also ignore any timings in my initial post they were incorrect.
Last edited by TheStatsMan (2011-07-26 07:40:48)

OSX hangs during boot or install

Hello all,
I'm writing this because I'm not really sure where else to post this at to get an indepth answer. Currently I have a dual G4 450mhz AGP PowerMac that I bought used. When I purchased it, it had 768mb of ram and the only thing it didn't have was a working hard drive. After putting in a new hard drive the system worked great when i intially installed OS9 and later OSX for fun.
However I had to remove the 768mb of RAM because a client PC needed it and that took priority over my dual G4 at the time. Just the other week I purchased 2 x 256mb of RAM from Omni Technologies (omnitechnologies.biz) which guarantees working ram for specified Apple systems.
Upon receiving that ram and installing it, I powered on the G4 only to find it would "hang" when booting OSX (10.3.9). The symptoms are as follows: When powering on I hear the normal chime and the white screen with gray apple logo appears. Seconds later the spinning progress indicator shows up spinning in circles as OSX is booting. However after about 5 minutes with no DVD/hdd activitity, the system then hangs. The gray apple logo changes to a gray 'prohibited' logo. It's the logo of the circle with the slash through it. Like the kind you see over no-smoking signs.
I figured the hard drive was messed up and I decided to reinstall OSX cleanly. However when I booted from the CD by pressing 'c', the EXACT SAME symptoms above happened. It was at this point I started getting really worried. So I decided to remove the hard drive temporarily and boot from the CD just to make sure it really was booting from the CD. Unfortunately the exact same symptoms happened.
Out of desperation to make sure that my hardware was OK, I decided to install OS 9.2.1 which installed and WORKED perfectly. I also installed UbuntuPPC and Slackintosh versions of linux which also installed and worked perfectly.
The issue appears to reside with OSX. I've borrowed friends cd's of 10.2-10.3 and all of them will NOT install. They start to boot from the CD, but never even make it to the first window.
Help!!
Brad

Actually trying one stick in each individual slot was one of the first things I did. Unfortunately that did not provide a resolution for me.
Thanks for the links regarding the broken folder/prohibitory sign. I read those and they made mention of resetting the nvram and pram. I just did that a bit earlier today but logging into the open firmware by pressing Option-Command-F-O and typing: reset-nvram; set-defaults; reset-all.
Upon the reboot and after I plugged the hdd with OSX on it back into the system, the resolution was a bit off as I figured. But this time there was no progress indicator. Instead only the gray apple logo showed and there was no response from the hdd or cdrom drive.
I also noticed that the USB mouses red light went out within the first 45 seconds of booting. I swapped out keyboards and mice and the new ones did the same thing as well. I also tested the memory in an imac I have and OSX that is installed ont heimac works gerat with that stick of memory. I'm leaning towards the fact that the memory I have is fine, being that it was ordered from a company that specifically guaranteed it to work on macs of all kinds.
Any other thoughts or ideas?

BB Torch 9860 Hangs during booting

I bought a BB Torch 9860 a week back. Yesterday night the handset got switched off as the battery had exhausted. In the morning when I was trying to switch it on it was not coming on. I put on charging, there was no indication of charging for some time then it started booting. The booting indicator (the line which indicates that the handset is being booted) went half way and stopped. The system did not respond to switch off button. The battery was removed and put back to restart. Every time it boots to half line and hangs. Would request someone to extend help please.
Regards, Tom

Hey thomas_k_s,
Welcome to the BlackBerry® Support Community Forums.
I would suggest to do a clean reload of the BlackBerry® device software as shown here: http://btsc.webapps.blackberry.com/btsc/KB11320, please test before restoring any data to the device.
If this resolves the issue do a selective restore of essential data (Address Book, Calendar, Task, Memos, BBM contacts etc.)
How to use BlackBerry Desktop Software to restore data to a BlackBerry smartphone from a backup file
http://btsc.webapps.blackberry.com/btsc/KB10339
If the issue still persists after the reload, further investigation might be required. To help further diagnose the cause, contact your wireless service provider or BlackBerry® Technical Support Services for further review and support.
Thank you.
-HB
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

V570 hangs during boot up - message "please wait"

I just got a new V570 Lenovo IdeaPad laptop on Sunday. It was working fine until Monday. I tried to start it up and it paused at the Please Wait screen. I didn't know what to do so I held the power button until it shut down. I then left it for a bit and it started up fine. Now, this has happened again and I am guessing it is not good. How can I fix it?
Solved!
Go to Solution.

UPDATE - OFFICIAL LENOVO SOLUTION
Please follow the link above to the Lenovo support site - this tip covers a software hang condition / please wait message caused by an interaction with the fingerprint reader and veriface software which may develop under certain conditions on V470/V570 and B470/B570 systems.
who knows - you may have fixed it (DMB stack in CMOS). edit: removed suggestion about safe start since it didn't work..
The removing the battery and the power cord is similar to what we had to do with desktop mobos - unplug it , wait 10 seconds, press power-on a few times to bleed the power off the PSU, and then plug it in and start up - it takes power off the BIOS and causes it to re-create the DMB stack the next time you boot. DMB = info about each device .
I also advise you to get current with MS updates (not necessarily all the optional ones!).
IdeaPad V570-1066A9U, Built 5-22-2011, BIOS 44CN36WW(2011-08-04)
Win7 Pro x64 clean install. Sammy 840 Pro 128GB SSD. Fast! Used nice hardware manual to re-grease CPU and remove tiny bit of lint.

Hanging During Boot Up

Hi All, thanks in advance ...
When I boot my Macbook Pro (2.6ghz 4gb Ram) up it gets to where Leopard begins, the dock arrives and then it hangs for 30 seconds to 2 minutes whilst it seemingly displays the time and allows you to click on dock icons etc.
Any idea what could be causing this as I have not installed any programs recently and nothing loads up on boot.
Also (this could be related) by Windows XP partition via Boot Camp has also seemed to slow down a little and I now get some serious juddering when Im using Acid Pro 6
Thanks

Boot in Safe Mode (hold down Shift as it's starting up) and it will do a series system checks and repairs (it will be slow so be patient). Then Boot again and see if it's faster ?

2007 MacBook Pro Snow Leopard hangs during boot up

All I get is the grey screen and the little circle with the rotating fan blades. Then they stop spinning and it just hangs.
I cannot boot up. Is this a bad hard drive?
Are there other keys I could hit to make something work?
Thanks for looking at this last cry for help before I take it in.

Try booting in Safe Mode by holding the Shift key down on startup until you see the grey Apple backdrop with the spinning cogwheel and progress bar. You can let go of the Shift key when the progress bar appears. Booting in Safe Mode takes a long time, so be patient. Log in to your account, and reboot normally when you have reached a fully functional Desktop.

Solaris 10 hang during boot

Don't know if this is a right place, if it's not, please direct me, thanks!
I had a SPARC Ultra 10 machine running under Solaris 10, it was
running for couple months. Recently when I reboot it, it was hang at
"Use is subject to license terms."
I press STOP+A to bring me to ok prompt, then type boot -v, the
following is the output:
ok boot -v
Boot device: /pci@1f,0/pci@1,1/ide@3/disk@0,0 File and args: -v
The boot filesystem is logging.
The ufs log is empty and will not be used.
Size: 0x704c8+0x1b8d2+0x2e1ba Bytes
module /platform/sun4u/kernel/sparcv9/unix: text at [0x1000000,
0x10704c7] data at 0x1800000
module misc/sparcv9/krtld: text at [0x10704c8, 0x10889e7] data at
0x1849a90
module /platform/sun4u/kernel/sparcv9/genunix: text at
[0x10889e8,0x11cd177] data at 0x184ee80
module /platform/SUNW,Ultra-1_10/kernel/misc/sparcv9/platmod: text at
[0x11cd178,0x11cd20f] data at 0x189ffc8
module /platform/sun4u/kernel/cpu/sparcv9/SUNW,UltraSPARC-IIi: text at
[0x11cd240, 0x11d92af] data at 0x18a0700
SunOS Release 5.10 Version Generic 64-bit
Copyright 1983-2005 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
Ethernet address = 8:0:20:fd:88:8e
mem = 524288K (0x20000000)
avail mem = 515342336
root nexus = Sun Ultra 5/10 UPA/PCI (UltraSPARC-IIi 440MHz)
pseudo0 at root
pseudo0 is /pseudo
scsi_vhci0 at root
scsi_vhci0 is /scsi_vhci
pcipsy0 at root: UPA 0x1f 0x0
pcipsy0 is /pci@1f,0
PCI-device: pci@1,1, simba0
simba0 is /pci@1f,0/pci@1,1
It hung *******************
ok boot cdrom
Boot device: /pci@1f,0/pci@1,1/ide@3/cdrom@2,0:f File and args:
Loading ufs-file-system package 1.4 04 Aug 1995 13:02:54.
FCode UFS Reader 1.12 00/07/17 15:48:16.
Redirected to slice: 1
Loading: /platform/SUNW,Ultra-5_10/ufsboot
Loading: /platform/sun4u/ufsboot
SunOS Release 5.10 Version Generic 64-bit
Copyright 1983-2005 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
| ***** hung in here again.
Any suggestions!
Peter

Hi Michael,
Thank you for your email.
I did as what you suggested and still couldn't boot it up. Here are output:
ok printenv
Variable Name                    Value               Default Value
tpe-link-test?                    true               true
scsi-initiator-id               7               7
keyboard-click?                    false               false
keymap
ttyb-rts-dtr-off               false               false
ttyb-ignore-cd                    true               true
ttya-rts-dtr-off               false               false
ttya-ignore-cd                    true               true
ttyb-mode                    9600,8,n,1,-          9600,8,n,1,-
ttya-mode                    9600,8,n,1,-          9600,8,n,1,-
pcia-probe-list                    1,2,3,4               1,2,3,4
pcib-probe-list                    1,2,3               1,2,3
mfg-mode                    off               off
diag-level                    max               max
#power-cycles                    260
system-board-serial#
system-board-date
fcode-debug?                    false               false
output-device                    screen               screen
input-device                    keyboard          keyboard
load-base                    16384               16384
boot-command                    boot               boot
auto-boot?                    false               false
watchdog-reboot?               false               false
diag-file
diag-device                    net               net
boot-file
boot-device                    disk net          disk net
local-mac-address?               false               false
ansi-terminal?                    true               true
screen-#columns                    80               80
screen-#rows                    34               34
silent-mode?                    false               false
use-nvramrc?                    false               false
nvramrc
security-mode                    none
security-password
security-#badlogins               0
oem-logo
oem-logo?                    false               false
oem-banner
oem-banner?                    false               false
hardware-revision
last-hardware-update
diag-switch?                    true               false
ok
ok probe-scsi-all
/pci@1f,0/pci@1/scsi@1
ok
ok probe-ide
Device 0 ( Primary Master )
ATA Model: ST340016A
Device 1 ( Primary Slave )
Not Present
Device 2 ( Secondary Master )
Removable ATAPI Model: CRD-8483B
Device 3 ( Secondary Slave )
Not Present
ok
ok test-all
Testing /SUNW,ffb@1e,0
Testing /pci@1f,0/pci@1/scsi@1
No targets found
Selftest failed. Return code = -1
Testing /pci@1f,0/pci@1,1/SUNW,m64B@2
Display not installed
Test hardware registers - passed Ok
Test RamDAC - passed Ok
Test Frame buffer - passed Ok
Testing /pci@1f,0/pci@1,1/network@1,1
Hme register test --- succeeded.
Internal loopback test -- succeeded.
Transceiver check -- Using Onboard Transceiver - Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading LInk status. Check cable and try again.
AutoNegotiation Timeout.
Check Cable or Contact your System Administrator.
Link Down.
failed.
Selftest failed. Return code = -1
Testing /pci@1f,0/pci@1,1/ebus@1fdthree@14,3023f0
Testing floppy disk system. A formatted disk should be in the drive.
Recalibrate failed. The floppy drive is either missing, improperly connected, or defective.
Selftest failed. Return code = -1
ok
ok boot cdrom -sv
Boot device:/pci@1f,0/pci@1,1/ide@3/cdrom@2,0:f File and args: -sv
Size: 0x7a768+0x1c319+0x30443 Bytes
module /platform/sun4u/kernel/sparcv9/unix: text at [0x1000000,0x107a767] data at 0x1800000
module misc/sparcv9/krtld: text at [0x107a768,0x10933af] data at 0x184c760
module /platform/sun4u/kernel/sparcv9/genunix: text at [0x10933b0,0x11f0f17] data at 0x1852000
module /platform/SUNW,Ultra-5_10/kernel/misc/sparcv9/platmod: text at [0x11f0f18,0x11f0faf] data at 0x18a4558
module /platform/sun4u/kernel/cpu/sparcv9/SUNW,UltraSPARC-IIi: text at [0x11f0fc0,0x11fd1c7] data at 0x18a4c80
SunOS Release 5.10 Version Generic_118833-33 64-bit
Copyright 1983-2006 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
Ethernet address = 8:0:20:fd:88:8e
Using default device instance data
mem = 524288k (0x20000000)
avail mem = 5144596864
root nexus = Sun Ultra 5/10 UPA/PCI (UltraSPARC-IIi 440MHz)
pseudo0 at root
pseudo0 is /pseudo
scsi_vhci0 at root
scsi_vhci0 is /scsi_vhci
pcipsy0 at root: UPA 0x1f 0x0
pcipsy0 is /pci@1f,0
PCI-device:pci@1,1, simba0
simba0 is /pci@1f,0/pci@1,1
********stucked
The strange thing is that I replaced a hard disk yesterday and at one time I was able to boot it to single user mode, but when I tried to install OS on the new disk, it stopped at the place where I described as above again.
I have no totally no clues where the problem might be.
Appreciate your helps.
Peter

Workstation hangs during boot from OVM Server CD

Newbie here. Downloaded OVM and created bootable CD just this afternoon.
The hardware is a Dell Precision 390 with 4gB RAM; 64bit technology (Intel EM64T); BIOS at 2.2.0; Intel Matrix Storage Manager (RAID5). Virtualization Technology option is "on".
When I boot the Precision, it stalls at the Intel Matrix Storage Manager screen as the boot CD is being accessed. No messages. Simply hangs with the system unresponsive to the hard connected keyboard.
Any hints regarding how to begin diagnosing will be greatly appreciated.

927071 wrote:
When I boot the Precision, it stalls at the Intel Matrix Storage Manager screen as the boot CD is being accessed. No messages. Simply hangs with the system unresponsive to the hard connected keyboard.Verify the md5sum of the downloaded ISO. If that matches, reburn the CD at a lower speed. Try booting the CD on another machine as well, to see if it's just this machine, or the CD itself that doesn't work.

Plymouth causes tty1 to tty6 to hang during boot

Similar Messages

Maybe you are looking for