Poblem after upgrade Prime NCS to Infrastructure

Hi,
I just upgrade Prime NCS 1.1.1.24 to 2.0 becuase we had several problem with NCS Aplication, after this upgrade I can´t longer see the Access Point on the floor maps, the APs are still assigned to the map and if I try to edit the location or asign APs to a new map, the aplication keeps loading but doesn´t do anything. I follow the quick installation guide for upgrading and installed the ncs_1_1_1_24-Update.13.4.tar.gz patch.
thanks for your help

You should be able to, but your best bet is to bring up a new VM on PI 1.3, and rehost the license. Then you can export the map's and import the map's on your new VM PI 1.3. If you try to downgrade, make sure you take a snapshot of the VM, so you can revert in case it doesn't work.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

Similar Messages

Some client data not being populated after upgrading to NCS 1.1.0.58

After upgrading to Cisco Prime NCS 1.1.0.58 some of the client data is not being populated or gathered. The graphs labeled "Client Count By Association/Authentication" and "Client Count By Wireless/Wired" are no longer being updated? Not sure what was changed during the upgrade or where to look to get it to start collecting the data again?

Eajackson,
Make sure your WLC, MSE and WCS/NCS code matches the compatibility matrix here:
http://www.cisco.com/en/US/docs/wireless/controller/5500/tech_notes/Wireless_Software_Compatibility_Matrix.html
Sent from Cisco Technical Support iPhone App

Upgrade Prime NCS

I have a Prime NCS appliance running 1.0.2.29 and I need to upgrade it to 1.1.0.58. I have downloaded the code from the Cisco site but I need to know how to upgrade the NCS.

Use the following command to upgrade from NCS 1.0 to NCS 1.1.0.58:
# application upgrade NCS-upgrade-bundle-1.1.0.58.tar.gz wcs-ftp-repo
In the preceding command, NCS-upgrade-bundle-1.1.0.58.tar.gz is the upgrade bundle file, which is available for download.
The repository used in the example, wcs-ftp-repo, can be any valid repository.
Examples of repository configurations follow.
FTP Repository:
# configure
(config)# repository wcs-ftp-repo
(config-Repository)# url ftp://ip-address
(config-Repository)# user ftp-user password plain ftp-user
(config-Repository)# exit
(config)# exit
SFTP Repository:
# configure
(config)# repository wcs-sftp-repo
(config-Repository)# url sftp://ip-address
(config-Repository)# user ftp-user password plain ftp-user
(config-Repository)# exit
(config)# exit
TFTP Repository:
# configure
(config)# repository wcs-tftp-repo
(config-Repository)# url tftp://ip-address
(config-Repository)# exit
(config)# exit
#

Upgrade Prime NCS v1.2 to Prime Infrastructure 1.4

Hello!!!!!
I need your help
How do you do for upgrade Cisco Prime Network Control System version 1.2 to Cisco Prime Infrastructure version 1.4
I go to cisco.com->Downloads Home-> Products->Wireless->Wireless LAN Management-> Unified Wireless LAN Management->
Cisco Prime Infrastructure-> Cisco Prime Infrastructure 1.4->Prime Infrastructure Software-1.4.0
I download PI-upgrade-bundle-1.4.0.45.tar.gz
is similar to upgrade to switch o router???

What I would do, is export the Maps. Then I would shut down the current VM, load the 1.4 OVA as a new install. Once you have the WLC added, you can then import the Maps.
This method will keep the DB from getting corrupted, and maintain your Maps and AP placements.
HTH,
Steve
Please remember to rate useful posts, and mark questions as answered

Problem after upgrade a PRIME-NCS-APL-K9 from version 1.1.0.58 to Prime Infrastructure 1.2

I have upgraded a PRIME-NCS-APL-K9 from version 1.1.0.58 to Prime Infrastructure 1.2
First I have installed the Path "ncs_patch-1.1.0.58-upgrade-pi_1.2.tar.gz" and then the
"PI-upgrade-bundle-1.2.0.103.tar.gz".
after the upgade I have got the Message "Upgrade Successful".
Now when I start the NCS i get the following error message
egghead/admin# ncs start
Starting Network Control System...
Unable to verify hardware.
This may take a few minutes...
Health Monitor is already running.
Failure during Network Control System startup. Check launchout.log for details.
In the launchout.log are this messages:
Starting Health Monitor as a primary
Checking for Port 8082 availability... OK
truststore used is /opt/CSCOlumos/conf/truststore
truststore used is /opt/CSCOlumos/conf/truststore
Starting Health Montior Web Server...
Health Monitor Web Server Started.
Starting Health Monitor Server...
Health Monitor Server Started.
Starting Remoting Service: Reporting Server
Checking for running servers.
00:00 Check complete. No servers running.
Starting Server ...
Starting Remoting Service: Reporting Server
The Report Server startup script is already running waiting for report server to start
Starting Remoting Service: Reporting Server
The Report Server startup script is already running waiting for report server to start
Starting Remoting Service: Reporting Server
The Report Server startup script is already running waiting for report server to start
Starting Remoting Service: Reporting Server
The Report Server startup script is already running waiting for report server to start
have anyone an idea whats wrong?
thank you for your help
Kurt

i have the same problem
NCS/admin# ncs status
Health Monitor Server is starting.
Reporting Server is Starting
Ftp Server is running
Database server is running
Tftp Server is running
Matlab Server is running
NMS Server is stopped.
SAM Daemon is running ...
DA Daemon is running ...
Syslog Daemon is running ...
status
I try it
To get it back up and running do the following from the CLI.
1. Stop the NCS
2. Run 'ncs db reinitdb'
3. Start the NCS
but the status is the same

Can PRIME-NCS-APL-K9 upgraded from 2.0 to 2.2

Dears,
I have Cisco prime infrastructure Appliance "PRIME-NCS-APL-K9 " use this version 2.0.0.0.294 and have the following spec.
Total RAM Memory: 16278820 kB
CPU Core Count: 16
Disk 0: Capacity: 437.90 GB
can i upgrade it from 2.0.0.0.294 to CPI 2.2
Waiting your feedback plz.
Regards,

Users deploying the Prime Infrastructure physical appliance can choose from the Gen 1 or Gen 2 options shown in Table 2. The The Gen 1 and Gen 2 physical appliance capacities match those of the virtual appliance Standard and Professional options, respectively.
http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/2-2/quickstart/guide/cpi_qsg.html#53444
Table 2 Prime Infrastructure Physical Appliance Options
Physical Appliance Options
2.X Option
Gen 1
Gen 2 3
Appliance Image Format
Bare Metal/ISO
Bare Metal/ISO
Equivalent 1.x Option
Physical Appliance
Physical Appliance
Hardware Specifications
CPU (cores/threads)
8 C/16 T
10 C/20 T
Memory
16 GB
64 GB
Disk Capacity
4x300 GB
4x900 GB
RAID Level
RAID 5
RAID 10
Disk I/O Speed
200 MBps
200 MBps

Upgrade from NCS to Prime

Hi.
I am trying to upgrade from NCS ver 1.1.1.24 to Prime 1.2. With the script ncs_patch-1.1.1.24-upgrade-pi_1.2.tar.gz.
And everything runs smooth until Stage 6 of 7., when Updating Database Schema .. is starting
Stage 6 of 7: Updating Database Schema ...
             : This could take long time based on the existing data size.
                 Stage 1 of 5: Pre Migration Schema Upgrade ...
                                       -- complete. Time Taken : 0 hr, 0 min, 52 sec
                 Stage 2 of 5: Schema Upgrade ...
                               : This could take long time based on the existing data size.
Here everything stops. I have waited for 5 hours now is this normal?
Regards
Johan

It looks like you may be able to restore the data as it says here but you may need to simply export the database, install PI and restore.
http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/1.2/quickstart/guide/cpi_qsg.html#wp56790
Upgrading Cisco Prime Infrastructure
You can upgrade the following Cisco Prime Network Control System products to Cisco Prime Infrastructure 1.2:
•Cisco Prime Network Control System 1.0.0 (NCS 1.0 MR2, 1.0.2.29)
•Cisco Prime Network Control System 1.1.0 (NCS 1.1 FCS, 1.1.0.58)
•Cisco Prime Network Control System 1.1.1 (NCS 1.1 K MR1, 1.1.1.24)
•Cisco Prime Network Control System (WAN) 1.1.0 and Cisco Prime Assurance Manager 1.1.0 (NCS-WAN/PA 1.1 FCS, 1.1.0.1114)
•Cisco Prime Network Control System (WAN) 1.1.1 and Cisco Prime Assurance Manager 1.1.1 (NCS-WAN/PA 1.1.1 MR1 FCS, 1.1.0.1116)
You can upgrade using either of the following methods:
1. Standard—Upgrades your existing system to version 1.2. All existing data is retained and you will be using the same size OVA at the end. The existing product will not be operational until the upgrade is complete. This is the normal option for most users. For details, see Performing a Standard Upgrade.
2. Migration—Allows you to back up the data from your existing system, install Cisco Prime Infrastructure 1.2 as a new system, and restore the existing system's data to the new system. You can then decommission the old system. This option is preferred if you want to migrate to a larger OVA, cannot disturb your production system, or have a large network. For details, see Performing a Migration Upgrade.

Upgrading prime infrastructure 2.1.0.0.78 - 2.1 cannot do app backup

Hi All
Trying to do an upgrade prime 2.1.0.0.78 to prime 2.2.
I have saved an app backup off the exisitng prime 2.1.0.0.78
However when i try to restore to the new prime infra 2.2
with the backup from the 2.1.0.0.78 it fails with a database error
My technical support say i should change the new vm server
to match ip addresses etc with the old one but that cant be right
as this is the official blurb for the types of backups ...
Application backups: These contain all Prime Infrastructure application data, but do not include host-specific settings, such as the server hostname and IP address. Application backups are intended for use when Prime Infrastructure is running as an OVA on customer-supplied hardware, as restoring from the backup may need to be to a server with completely different host settings.
Appliance backups: These contain all application data and host-specific settings, including the hostname, IP address, subnet mask, and default gateway. Appliance backups are intended for use when Prime Infrastructure is running on a Cisco-supplied appliance, and restoration is most likely to be to a server with the same host settings.
I am obviously using the application backups
Kind regards
Steve

Here you go ....
Initiating restore. Please wait...
Restore Started at 02/02/15 17:29:54
Stage 1 of 9: Transferring backup file ...
-- completed at 02/02/15 17:30:59
Stage 2 of 9: Decrypting backup file ...
-- completed at 02/02/15 17:34:00
Stage 3 of 9: Unpacking backup file ...
-- completed at 02/02/15 17:34:01
Stopping strongSwan IPsec failed: starter is not running
Stage 4 of 9: Decompressing backup ...
-- completed at 02/02/15 17:34:31
Stage 5 of 9: Restoring Support Files ...
-- completed at 02/02/15 17:34:32
Stage 6 of 9: Restoring Database Files ...
-- completed at 02/02/15 17:34:51
Stage 7 of 9: Recovering Database ...
Error while restoring and recovering database, please check the logs.

Difference between Cisco Prime Infrastructure and Cisco Prime NCS

Dear All,
I am currenctly confused in choosing what type of Cisco Prime.
1.Which one should I choose? should I order Cisco Prime NCS or directly purchase Cisco Prime Infrastructure (since Cisco Prime Infrastructure has the feature of NCS)?
2, Why does Cisco not just remove the Cisco Prime NCS ordering Part Number since Cisco Prime Infrastructure already cover the NCS?
Please advice me

Hortono,
I started to write a long and lengthy msg about my experience with this, but instead, let me direct you to the horses mouth. There have been weekly webinars in regards to Cisco Prime (many differnt products under this headline) including Infrastructure. I believe the Cisco PI is actually scheduled for Thursdays, so hopefully you'll look at this in time to catch it and ask your questions from the gurus.
https://ciscosales.webex.com/ciscosales/j.php?J=200462944&PW=NMzhhNjM5OGU3
Looks like this may be the last week, catch it if you can.

Cisco Prime NCS 1.3 Licensing issue

Hello,
I am installing Cisco prime NCS x 2 servers. I downloaded the licenses which are ordered allong with the devices as follows.
Product Name                : L-PI12-LF-50-LIC
    Product Description         : L-PI12-LF-50-LIC:Prime Infrastructure 1.2 - Lifecycle - 50 Device Lic PAK
    Product Qty                 : 1
    UDI                        : PID: PRIME-NCS-APL-K9
The issue is, the NCS appliance was not started properly and then I used the CD which came along with the server (NCS 1.3). Now my system is up and running but it is NCS 1.3 and when i upload the licenses, it shows that the UID is not matching with the system. Is this because the licenses are issued for NCS 1.2 and my system runs on 1.3? If so, what do you suggest, do i need to download NCS 1.2, install it, add the license and then upgrade to 1.3?
Thanks for your advise,
Regards
Jay

Prime Infrastructure has a support forum at:
https://supportforums.cisco.com/community/netpro/network-infrastructure/network-management
Please post this to that forum to reach PI experts.
Regards

Cisco Prime NCS Recovery

Hi,
A Cisco Prime NCS physical appliance has been shipped with version NCS 1.1
Then it has been upgraded to:
1) ncs_patch-1.1.0.58-upgrade-12.tar.gz
2) PI-upgrade-bundle-1.3.0.20.tar.gz
Our customer have got only 1.2 licenses. How can we downgrade the appliance to 1.2 ?
Or how can we re-install 1.1 or 1.2, for both versions we did not find the iso's to download.
Thanks in advance

Hello,
What is the Current verison of NCS ,you are using ?
AFAIk, you can Installed PI 1.3 directly as PI 1.2 is not available for download.
Conatct the License Team and they will re-host the license for you.
you can downlaod the iso file from the below link:
http://software.cisco.com/download/release.html?mdfid=284652876&flowid=38562&softwareid=284272932&release=1.3&relind=AVAILABLE&rellifecycle=&reltype=latest
Note:Upgrade from Cisco Prime Network Control System 1.1.2.12 or 1.1.3.2 to Cisco Prime Infrastructure 1.3.0.20 is not supported.
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors ****

CPI : Duplicate "site groups" after upgrade

Hello,
We encounter a duplicate entry for "site groups" after upgrade from Cisco Prime Infrastructure 1.2 to PI 1.3.
This is visible under the Lifecycle view.
Have you ever seen this issue ?
Anyone know how to remove one of it without losing data ?
Thanks in advance,
Kind regards,
Cedric

Hi Livio,
Sorry but we haven't find any solution at this time... But I found the following bug which is open for the CPI plateform from 1.3 :
"CSCue76386 - After Restoring PI DB, duplicate site group are displayed in DWC"
There is no workaround a this time.
Regards,
Cedric

After upgrading to Mountain Lion 10.8.2, I cannot print to my Samsung laser printer ML 2525w? How can I get this set up to print?

After upgrading to Mountain Lion 10.8.2 on my iMac, I cannot print to my Samsung B&W Laser printer ML 2525W either by USB or wireless. Any help on how to setup or reconfigure would be apprecaited.
I either print blank pages or prints one time then goes off line, or spits out a bunch of blank paper, etc. Have gone through all the standard fixes, reboot, reset , reload driver, etc.

From the link to the Thread you provided, I worked through the one message procedures that were listed.
For ease of reference, I have copied them and printed them below. This was an old thread but the guidance still works with no firmware upgrade required.
I would stress that you MUST delete any and all files relating to USB connection of the printer to the MAC, including all print drivers (from both Apple and Samsung either from CD or web downloads) and all print queues, etc. I was only able to get the printer to properly hand shake with my Mac by setting it up wirelessly after all old files were deleted with hard power off reboots on both the Mac and Printer.
I hope that someone from Apple will pass this note along to their programing department because there is some type of incompatibility in the new ML OS and the Samsung ML2525w print dirvers used for a cable (USB) type connection. Apple needs to be talking to Samsung to get the USB issue resolved. I am going to post this same message on the Samsung site to see if someone from there will contact Apple to work together on a final solution for USB connectivity.
Here is the steps I followed to get my ML2525w to work in the wireless mode. Again, I cannot stress the need to clean out all the old files (drivers, print queues, etc. - everything) before setting up wirelessly.
As a note, I ran this printer with Lion for almost 2 years and it always worked fine (both wireless and USB). From other comments on the thread, users were good with this printer using Lep. and Snow Lep also. - - no issues from either a USB connection or wireless until Mountain Lion.
Before the fix, I was experiencing many of the same issues as described on user chat threads, printer going offline after a print job. 1st page sometimes printing but all the rest of the pages were garbage. No printing at all. Printer just running a bunch of blank pages out. etc.
I run an iMAC 27" desktop with the ML OS upgrade just installed from Lion.
"I've just installed one of these printers for my parents.
First of all, don't waste your time connecting the ML-2525W as a USB printer. The printer will go offline after each print job. It's hopeless, at least (I assume) until Samsung gets around to publicly releasing a firmware update.
Instead, you have to use the ML-2525W as a wireless printer. In that mode, it works fine.
This is what I did:
(1) First, if you have already attempted to install the Samsung driver software from the included CD-ROM, uninstall it. Get the uninstaller from the Samsung support site:
http://www.samsung.com/us/support/downloads/ML-2525W
Download the "Printer Driver (ver. 4.0)" ZIP file. It unzips to a folder that contains the uninstaller. Likewise, download the "Smart Panel Driver" ZIP file and uninstall the Smart Panel software.
(2) Disconnect the USB cable from the printer, if it is connected. Pull the power plug on the printer and power cycle it.
(3) Restart your Mac.
(4) Go to the "Printer Driver (ver. 4.0)" folder that you previously unzipped. Inside it is a folder named "WirelessSetting". Open the folder and run the "Wireless Setting.app".
(5) The application will ask you to connect the USB cable to the printer. Do so, and the Mac should be able to communicate with the printer to perform the wireless setup.
(6) The application will show you a list of wireless networks. One of them is the wireless interface in the printer (ad-hoc). You can ignore that unless you intend to use the printer without connecting to another wireless network. In my case, I selected the wireless network in my parents' home (infrastructure) and entered the security passphrase. The application then configured the wireless interface in the ML-2525W to connect to the home network.
(7) The Wireless Setting application will then tell you to disconnect the USB cable.
(8) After finishing the Wireless Setting application, go to Word, Textedit, Pages, or Safari, and select a file or page to print. In the print dialog window, you should see the ML-2525W as a "Nearby Printer" (i.e. via Bonjour). Select the ML-2525W, and your Mac will automatically connect to Apple's Software Update and download the latest Samsung driver. If for any reason the Software Update download does not succeed, you can manually download and install the Apple driver using the previously published link in this discussion.
(9) After that, you should be able to print to the ML-2525W whenever you want, without the printer going offline.
(10) If you have a USB printer queue still in your Print & Fax Preferences (from your previous unsuccessful attempt to connect via USB), you can delete it. You only need to keep the Bonjour queue.
Obviously YMMV, but in my case this procedure got the printer working reliably without the need for a firmware update."
MacBook (white 12"), Mac OS X (10.6.5)

GMAIL Lost after upgrade to IOS 8.3

I have lost access to my GMAIL accounts after upgrading to IOS 8.3 !
IOS Settings does not provide me a way to enter a new application password for the account - there is NO PASSWORD box displayed anywhere in the GMAIL configuration. So I tried deleting the account and re-adding it but i get stuck in an endless loop of two-step confirmation and it "appears" to add the account (prompts me for which features - mail, notes, calendar, etc.) but then when all is said and done NO GMAIL ACCOUNT shows up in my list of accounts. WTH?
And trying to navigate Apple's support screens has become an exercise in frustration and futility!
Anyone got any ideas how to fix this mess?

Just wanted to add to this thread. I found out that this might be related to using the iCloud Keychain on iOS and with a computer using Mac OS X. Due to how iCloud Keychain stores all passwords across all synced devices, which can be both iOS devices and Mac OS X computers, the methods for accessing and updating those passwords has changed. Not sure whether this is intentional by Apple or not, but it seems that the ability to update passwords stored in iCloud Keychain is not something you can do through iOS (or at least, I have not been able to find a way to access the keychain and view/update any of the passwords stored there).
If you have a computer set up to use iCloud Keychain, you can use the Keychain.app to view/modify any passwords that are stored there, which "should" update the passwords stored on the iOS device, if that keychain item is actually synced to the iCloud Keychain. (Tested this and confirmed)
The problem appears to arise specifically if you only have one iOS device (or only have iOS devices) using iCloud Keychain. The option to update passwords seems to be missing. Not sure it this is new to 8.3, but this is the first time I have run into this problem, and cannot seem to find any reports detailing this problem anywhere else. In fact, to a greater degree, most articles/sites that discuss the iCloud Keychain only refer to the usernames and passwords stored by Safari, which are not the only passwords and information stored by the iCloud Keychain. This issue being a prime example.
I did notice that when re-adding my gmail account using my iPhone, the login page was actually just a webkit presentation of the gmail login page (webkit being the underpinnings of Safari, used for displaying HTML, but not actually the full app or Safari), which is where I entered my username and password, which I am assuming is now stored in my iCloud Keychain. I even checked in Settings>Safari>Passwords&Autofill>Saved Passwords, and my gmail username and password are NOT listed there, so iCloud Keychain is storing some items somewhere else, which is not accessible by the end user through the UI.

3.1.1 upgrade breaks OEM 12c Infrastructure Cloud

Greetings,
After upgrading from 3.0.3 to 3.1.1 (manager first then servers) all of the Oracle VM targets in OEM 12c Infrastructure Cloud have metric collection errors, specifically "ERROR - Failed to connect to OVM Manager1010", i.e. oracle.sysman.vt.ovm.integration.api.EMOVMCommunicationServiceException: 1010: Error while performing the operation: Connection to the remote OVM Manager url tcp://ovm-laforge.sf.mokum.com:54321 failed. Please make sure that the OVM Manager version is 3.0.2 or greater and the service url and the credentials are correct.Check exception cause and logs for more details.[com.oracle.ovm.mgr.api.exception.FailedOperationException:OVMAPI_6000E Internal Error: Connection refused Connection refused.
We walked through the check in "Oracle VM Manager Login Fails with OVMAPI_6000E [ID 1416443.1" , all systems go....
sh ./ovm_upgrade.sh --dbuser=ovs --dbpass=xxxxxxx --dbhost=localhost --dbport=1521 --dbsid=orcl
COMMAND: ./ovm_upgrade.sh --dbuser=ovs --dbpass=xxxxxxx --dbhost=localhost --dbport=1521 --dbsid=orcl
find: /tmp/ovmpatches: No such file or directory
Copying xsl files to patch path location
`./transform_003000002000_010.xsl' -> `/tmp/ovmpatches/transform_003000002000_010.xsl'
`./transform_003000003000_010.xsl' -> `/tmp/ovmpatches/transform_003000003000_010.xsl'
`./transform_003001001000_010.xsl' -> `/tmp/ovmpatches/transform_003001001000_010.xsl'
`./transform_003001001000_020.xsl' -> `/tmp/ovmpatches/transform_003001001000_020.xsl'
Copying deleted classes files to patch path location
`./deletedClasses.xml' -> `/tmp/ovmpatches/deletedClasses.xml'
INFO (OvmUpgrade.java:206) Oracle OVM Manager Upgrade Processor
INFO (OvmUpgrade.java:207)
INFO (OvmUpgrade.java:488) Upgrade Initialization Starting
INFO (OdofDirector.java:220) Oracle Distributed Object Fabric (ODOF): Copyright (C) 2007, 2012 Oracle. All rights reserved.
INFO (OdofDirector.java:221) ODOF Version: 1.0.0.0
INFO (OdofDirector.java:222) Initializing...
INFO (OdofDirector.java:279) Initialization Complete!
INFO (OvmUpgrade.java:490) Upgrade Initialization Complete
The /u01/app/oracle/ovm-manager-3/machine1/base_adf_domain/servers/AdminServer/logs/AdminServer.log logs are clean....
This log is quickly filling up our free space (5G worth of logs :-): /u01/app/oracle/product/agent/agent_inst/sysman/log/gcagent_errors.log with:
2012-05-12 17:43:38,405 [129:GC.Executor.7 (oracle_vm_zone:Page:Response) (oracle_vm_zone:Page:Response:Response)] ERROR - Failed to connect to OVM Manager1010: Error while performing the operation: Connection to the remote OVM Manager url tcp://ovm-laforge.sf.mokum.com:54321 failed. Please make sure that the OVM Manager version is 3.0.2 or greater and the service url and the credentials are correct.Check exception cause and logs for more details.[com.oracle.ovm.mgr.api.exception.FailedOperationException:OVMAPI_6000E Internal Error: Connection refused Connection refused
From the manager:
# lsof -i|grep 54321
java 3067 oracle 454u IPv6 710576 0t0 TCP localhost.localdomain:43620->localhost.localdomain:54321 (ESTABLISHED)
java 3067 oracle 511u IPv6 19638 0t0 TCP localhost.localdomain:54321 (LISTEN)
java 3067 oracle 710u IPv6 19639 0t0 TCP localhost.localdomain:64163->localhost.localdomain:54321 (ESTABLISHED)
java 3067 oracle 711u IPv6 19640 0t0 TCP localhost.localdomain:54321->localhost.localdomain:64163 (ESTABLISHED)
java 3067 oracle 712u IPv6 19641 0t0 TCP localhost.localdomain:54321->localhost.localdomain:64164 (ESTABLISHED)
java 3067 oracle 713u IPv6 19642 0t0 TCP localhost.localdomain:64164->localhost.localdomain:54321 (ESTABLISHED)
java 3067 oracle 714u IPv6 19643 0t0 TCP localhost.localdomain:54321->localhost.localdomain:64166 (ESTABLISHED)
java 3067 oracle 715u IPv6 19645 0t0 TCP localhost.localdomain:64166->localhost.localdomain:54321 (ESTABLISHED)
java 3067 oracle 716u IPv6 19646 0t0 TCP localhost.localdomain:54321->localhost.localdomain:64168 (ESTABLISHED)
java 3067 oracle 717u IPv6 19649 0t0 TCP localhost.localdomain:64168->localhost.localdomain:54321 (ESTABLISHED)
java 3067 oracle 718u IPv6 19650 0t0 TCP localhost.localdomain:54321->localhost.localdomain:64173 (ESTABLISHED)
java 3067 oracle 720u IPv6 19781 0t0 TCP localhost.localdomain:64173->localhost.localdomain:54321 (ESTABLISHED)
java 3067 oracle 721u IPv6 19782 0t0 TCP localhost.localdomain:54321->localhost.localdomain:64175 (ESTABLISHED)
java 3067 oracle 723u IPv6 19798 0t0 TCP localhost.localdomain:64175->localhost.localdomain:54321 (ESTABLISHED)
java 3067 oracle 749u IPv6 20742 0t0 TCP localhost.localdomain:64235->localhost.localdomain:54321 (ESTABLISHED)
java 3067 oracle 750u IPv6 20743 0t0 TCP localhost.localdomain:54321->localhost.localdomain:64240 (ESTABLISHED)
java 3067 oracle 757u IPv6 20149 0t0 TCP localhost.localdomain:54321->localhost.localdomain:64207 (ESTABLISHED)
java 3067 oracle 758u IPv6 20761 0t0 TCP localhost.localdomain:64240->localhost.localdomain:54321 (ESTABLISHED)
java 3067 oracle 759u IPv6 20167 0t0 TCP localhost.localdomain:64207->localhost.localdomain:54321 (ESTABLISHED)
java 3067 oracle 760u IPv6 20168 0t0 TCP localhost.localdomain:54321->localhost.localdomain:64209 (ESTABLISHED)
java 3067 oracle 761u IPv6 20185 0t0 TCP localhost.localdomain:64209->localhost.localdomain:54321 (ESTABLISHED)
java 3067 oracle 762u IPv6 20186 0t0 TCP localhost.localdomain:54321->localhost.localdomain:64235 (ESTABLISHED)
java 3067 oracle 763u IPv6 20762 0t0 TCP localhost.localdomain:54321->localhost.localdomain:64247 (ESTABLISHED)
java 3067 oracle 765u IPv6 20802 0t0 TCP localhost.localdomain:64247->localhost.localdomain:54321 (ESTABLISHED)
java 3067 oracle 770u IPv6 464327 0t0 TCP localhost.localdomain:54321->localhost.localdomain:43620 (ESTABLISHED)
java 3067 oracle 771u IPv6 21578 0t0 TCP localhost.localdomain:54321->localhost.localdomain:64313 (ESTABLISHED)
java 3067 oracle 779u IPv6 21617 0t0 TCP localhost.localdomain:64313->localhost.localdomain:54321 (ESTABLISHED)
java 3067 oracle 781u IPv6 25612 0t0 TCP localhost.localdomain:54321->localhost.localdomain:11597 (ESTABLISHED)
java 3067 oracle 783u IPv6 74799 0t0 TCP localhost.localdomain:11597->localhost.localdomain:54321 (ESTABLISHED)
I recollect in 12.0, not 12.1, there was a required OVM password deep in a hidden nook in the OEM Infrastructure Cloud GUI, I cant find it in 12.1, could this be the issue?
Respectfully,
Roddy

A quick update, Oracle support just informed me the 3.1.1 is not certified with OEM 12c 12.1. Not very helpful information, but its a start.
At first glance it appears that the OVM development team made changes that break the virtualization plug-in.
Any assistance and/or workarounds would be greatly appreciated!

Poblem after upgrade Prime NCS to Infrastructure

Similar Messages

Maybe you are looking for