Pod Freezes Then Goes Onto A White Screen Then Apple Logo Screen, Should I Bring It To Best Buy?

My Pod lately has been going very slow but doesn't have very much Apps or music in it & today it just freezer on my games and then it went onto a white screen then the black Apple logo screen. It's been doing this for a month already. Should I bring it in ?

How old is it? And do you have Black Tie Protection on it?
If you like my post, or solution to your issue/question, go ahead and click on the little star by my name and/or accept the post as the Solution. It makes me happy.
I'm NOT an employee of Best Buy, or Geek Squad, though I did work as an Agent for a year 5 years ago. None of my posts are to be taken as the official stance that Best Buy will take on your situation. My advice is just that, advice.
Unfortunately, that's the bad luck of any electronic, there's going to be bad Apples... wait that's a horrible pun.

Similar Messages

Imac wont boot - i get a white screen with apple logo, and it loads to about 10%, then screen goes black

imac wont boot - i get a white screen with apple logo, and it loads to about 10%, then screen goes black

Hey there mtriest,
It sounds like you are unable to boot the iMac successfully as it keeps shutting down when you try to boot. I suggest the troubleshooting from the following article named:
Mac OS X: Gray screen appears during startup
http://support.apple.com/kb/ts2570
Disconnect, test peripheral devices and network cables
Note: "Peripheral devices" refers to external devices other than what came with your Mac, such as hard drives, printers, or hubs that you connect via a USB or FireWire cable.
Shut down your Mac. If necessary, hold your Mac's power button for several seconds to force it to power down.
Disconnect all peripheral devices such as external hard drives or printers (leave only the display, a keyboard, and mouse connected).
Disconnect any Ethernet cables.
Start up your Mac.
If you can start up this way, one or more of your peripheral devices (or installed software related to the device) is probably causing the gray screen issue. Connect one device, then restart your Mac to test for the issue. Repeat the process until you locate the device at issue. Make sure the device is powered if it needs to be to operate correctly. Check with the manufacturer of the device for support or possible software driver or firmware updates that may be available for the device. Try a different cable with the device if possible (such as a different USB or FireWire cable).
Note: If you have multiple peripheral devices and the issue only occurs when they are all connected, but not when each device is the only peripheral connected, see the Additional Information section below.
If you are using a desktop Mac with a third-party keyboard and/or mouse device, and the issue still occurs, try starting up with an Apple keyboard and mouse connected instead. Try starting with no keyboard and mouse connected, then connect them after start up. Also, try a different USB port on your Mac.
If the gray screen issue persists with no devices connected, go to the next section (with the peripherals still disconnected).
Perform a Safe BootSimply performing a Safe Boot may resolve this issue.
Shut down your Mac. If necessary, hold your Mac's power button for several seconds to force it to power down.
Start your Mac, then immediately hold the Shift key. This performs a Safe Boot. Advanced tip: If you want to see the status of a Safe Boot as it progresses, you can hold Shift-Command-V during start up (instead of just Shift).
Note: A Safe Boot takes longer than a typical start up because it includes a disk check and other operations.
If your Mac starts up as expected, immediately try restarting.
If the Safe Boot does not work, or the restart after a successful Safe Boot does not work, go to the next section.
There is additional information in the article with further troubleshooting if needed.
Thank you for using Apple Support Communities.
Cheers,
Sterling

When i plug in my ipod touch to charge it starts with the battery with the little bolt under it then it goes to the apple logo screen and after a while it flashes white and just shuts off and restarts the process. Whats wrong and how do i fix it?

when i plug in my ipod touch it goes to the battery witht he bolt under it the goes to the apple logo screen and after a while it will flash white like its trying to go to the lock screen but just restarts and restarts the process and keeps doing it. What should i do? Is there any way to fix it?

See if you missed anything here:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

So I keep trying to sync music to my iPhone from iTunes, and whenever I select the album the sync goes by really fast and nothing goes onto my phone. Then when I click "On this iPhone" it shows the songs, but they're grey, and I can't click on them. Help?

So I keep trying to sync music to my iPhone from iTunes, and whenever I select the album the sync goes by really fast and nothing goes onto my phone. Then when I click "On this iPhone" it shows the songs, but they're grey, and I can't click on them. Help?

Ok, sorry. And yes, I just restored my iPhone as new and tried to put all the songs on there before I even restored with my previous backup, but it still does the same thing... even when I just checked the option to sync only "selected music or videos". How's that possible?
P.S. After I tried syncing with checked songs only, nothing showed up under Music on my phone and this message popped up in iTunes: "The iPhone "..." could not be synced because the sync session failed to finish." If you could, please tell me what that means, thanks.

Hi my iMAc 27 inch starts up to the grey screen with apple logo and loading bar underneath it loads halfway then freezes up and shut down after a while please help

Hi my iMAc 27 inch starts up to the grey screen with apple logo and loading bar underneath it loads halfway then freezes up and shut down after a while please help

Try the tips listed here Mac OS X: Gray screen appears during startup - Apple Support

When I started my Mac the screen was white with the Apple logo and power motion icon running. I attempted to turn off Mac then a message stating "Debugger called: Button SCI . Also "Waiting for remote debugger connection." What is my next step?

When I started my Mac the screen was white with the Apple logo and power motion icon running. I attempted to turn off Mac then a message stating "Debugger called: <Button SCI>. Also "Waiting for remote debugger connection." What is my next step?

Hi , and a warm welcome to the forums!
Could be many things, we should start with this...
"Try Disk Utility
1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the First Aid tab.
4. Select your Mac OS X volume.
5. Click Repair Disk, (not Repair Permissions). Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
(Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)
If perchance you can't find your install Disc, at least try it from the Safe Boot part onward.
If 10.7.0 or later...
Bootup holding CMD+r, or the Option/alt key to boot from the Restore partition & use Disk Utility from there to Repair the Disk, then Repair Permissions.
And sorry to report that OSX is more Widows like than ever, but….
If that doesn't help Reinstall the OS.

I get a white screen with apple logo and progress bar on my imac mavericks

I get a white screen with apple logo and progress bar ,then computer shuts down
when I turn my imac back on same thing happens,every time same thing
pprogress bar only goes half way then computer shut down
is there a solution ?
if not is there a way to at least salvage some files and docs?
i Have the latest imac 27

Thanks I tried it but after I repaired my disk via disk utility at start up, it told me that
my disk can't be repaired and to try to back up my files so I can format it
but is there to back up my files?
also what I get is white screen with the progress bar not grey

White Screen with apple logo and a lock

Ok I shouldn't have messed around cause now I've lost everything
I normally sync on a PC-no problems...I decided to sync on my mac book, knowing I'd lose some stuff...I backed up too.
I was logged into itunes on laptop and logged out. I decided to just restore back to the version I happened to back up yesterday (cause now everything is lost). So when I did I restored it...then my iphone asked me if I wanted it to be a new phone or from an old version (I picked old) and when I connected to sync. the screen looked like all white except an apple logo and a small black lock on top right. This is what I saw on the screen when device syncs. It found device but seems like it isn't letting me in to do anything!!
This is on PC or laptop now.
Help

Well I'm going to bed..gotta be up at 5 am..hopefully they fix it by then and crossing my fingers that I can get stuff back in morning!
Thanks phil

Computer doesn't boot, stuck in white screen with Apple logo

I got a friend that has a MacBook 2.0GHz, Black. The computer had some sort of problem so he took out the HD and placed it into another computer (MacBook 2.2GHz, Black). For some reason whenever the computer boots, it gets stuck in the white screen with the gray Apple logo, and shows up a bar, as if it's loading some sort of firmware update. It never advances, and it doesn't go thru.
If he takes the same HD and puts it into an enclosure, first it would take a while to mount in another computer, and afterwards it would give some errors, but now it doesn't even load.
Before he had the issue with his original computer everything was working fine, and there was no update going on when the computer got broken. The problem that that computer has isn't related to the HD.

If you have physically removed the drive and connected it to another computer and it "took a while to mount" then it sounds like the drive itself is failing. Hopefully he maintains backups.
Boot the MacBook in "verbose" mode (press and hold down option+v while powering up)
http://support.apple.com/kb/HT1492
In this mode you will see all the boot messages scroll by instead of the typical white screen with Apple logo. You will likely be able to see messages indicating what the computer is trying to do -- for example messages indicating that having failures or retrying to read the hard drive.
The access arms on hard drives have to be precisely located above the "tracks" on the disk in order to read data. As the drive ages & wears, the accuracy of the arms can become sloppy, causing the read/write head to no longer be precisely located over a track. This results in failure to read correctly. Most drives have a useful life of about 5 years -- after which the failure rate will go up substantially. Fortunately, replacement hard drives are cheap.

ITunes Store wont open. Only thing appears is the white screen with Apple Logo

iTunes Store won't opeen. Only thing appears is white screen with Apple Logo and takes really, really long to load.

Hi Davin12,
I'm sorry to hear you are having issues acessing the iTunes Store from your Windows computer.
The article below may be able to help you with this issue.
Click on the link below to see more details and screenshots.
I've quoted some helpful highlights for you:
iTunes for Windows: iTunes Store connection troubleshooting
Remove pop-up blockers
Some pop-up or ad-blocking programs may interfere with the ability of iTunes to connect to the iTunes Store. Removing them in many cases will resolve the issue.
Flush DNS Setting in Windows
In some cases, the DNS information you computer uses to connect to the Internet needs to be reset. Follow these instructions to flush your Windows DNS information:
Windows XP
On the Start menu, click Run.
In the Open field type cmd and click OK.
In the resulting window, type ipconfig /flushdns and press Return on the keyboard.
You should see a message that the DNS Resolver Cache has been successfully flushed.
Windows Vista and Windows 7
On the Start menu, point to All Programs > Accessories and then right-click Command Prompt and chooseRun as Administrator from the shortcut menu. If Windows needs your permission to continue, click Continue.
In the resulting window, type ipconfig /flushdns and press Return on the keyboard.
You should see a message that the DNS Resolver Cache has been successfully flushed.
Note: If, in the command prompt, you see this message: "The requested operation requires elevation", close the command prompt and repeat steps 1 and 2 above to be sure that Administrator privileges are used to access to Command Prompt.
The article below will help you troubleshoot the issue from your computer or your iPod Touch:
iTunes: Advanced iTunes Store troubleshooting
I hope this information helps ....
Have a great day!
- Judy

Ipod 4 is displaying blue frozen screen and black screen with apple logo. I try to turn power off but as soon as it goes out it automatically reboots. Plugged it into the usb port on my mac and it doesnt do anything. It doesnt appear in Itunes. Help?

ipod 4 is displaying blue frozen screen and black screen with apple logo. I try to turn power off but as soon as it goes out it automatically reboots. Plugged it into the usb port on my mac and it doesnt do anything. It doesnt appear in Itunes. Help?

Let the battery fully darain. After charging for an least an hour try a reset and restore. Use Recovery mode if necessary.
If not successful, then time for an appointment at the Genius Bar of an Apple store.

My 2011 IMac will not boot up past the White apple logo screen with the whirly circle

My 2011 IMac will not boot up past the White apple logo screen with the whirly circle. I have tried various commands but to no avail. does anybody have any advice?

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

MacBook Pro White screen, No apple logo, No question mark

Hi guys
I've MacBook pro 13 2010 model
The Laptop turn on all the time when i press power button
but It's stuck in white screen ( without apple logo ) . With hard drive connected or no hard drive i still can't see the question mark folder
What i've done
- Reset NVRM ( shift + Command+ option + power ) and it worked as i can see light changed in the charger
- I removed the hard drive put new one, then again removed hard from the board but no luck
- connected the Laptop to a monitor but not even showing video in the external monitor
Why can't i press PRAM button. NVRM work OK but not PRAM ( Option + Apple logo + P + R )
so keyboard is fine

askmeplz82,
if you’re unable to boot into Mountain Lion’s Recovery mode, then that limits your self-help options. These options still remain:
Do you still have the two grey installation DVDs which originally came in the box with your MacBook Pro?
Do you have a bootable external disk?
Do you have access to a FireWire cable and access to a second Mac with a FireWire port?
Do you have a spare SATA disk which can be temporarily installed inside of your MacBook Pro?
If the answer to all of these is no, then your only remaining option is to make an appointment at an Apple store or other qualified service facility so that they can diagnose/repair your MacBook Pro.

Recently when clicking on Safari, it refused to open saying there were some components damaged. It was suggested I backup, remove OSX and reinstall. Now all I get is white screen and apple logo when starting. What to do?l

I Have an iMac desktop purchased in 2010 with OS X 6.1.6 and Snow Leapard. Recently after starting up, I was not able to open Safari. I checked for updates and all was well. I tried again and got a message saying Safari could not be opened because some components were damaged. After using Disk utilities to try and repair, it was suggested I uninstall OS X and reinstall from the disk. I did not at the time because I wanted to backup some info to a USB drive. But now when I startup all I get is the white screen and Apple logo and the loading symbol. What happened and How can Imfix it? I am not very tech savvy and don't know where to turn!

Hi nancy mfromamity harbor,
Welcome to the Support Communities! It sounds like reinstalling the Snow Leopard operating system is your next step. This should not affect the documents and data that you currently have on your iMac. I'll include the information to show you how below.
Mac OS X 10.6: Reinstalling Mac OS X
http://support.apple.com/kb/PH6606
Under some circumstances, you may need to reinstall Mac OS X. You can reinstall Mac OS X while keeping your files and user settings intact.
Note:To reinstall Mac OS X from another computer on your network, see:
Using another computer’s DVD or CD drive
To reinstall Mac OS X:
Insert the Mac OS X installation disc and double-click the Install Mac OS X icon.
Follow the onscreen instructions. In the pane where you select a disk, select your current Mac OS X disk (in most cases, it will be the only one available).
If you want to control which parts of Mac OS X are installed, click Customize, and then select the parts you want to install.
To start the installation, click Install.
If you purchased a standalone version of Mac OS X, these installation instructions are in a PDF file located on the Mac OS X installation disc.
If you need to reinstall the version of Mac OS X that was on your computer when you purchased it, or if you need to restore all the software on your computer (including Apple software, third-party applications, and other printer drivers), refer to the documentation that came with your computer.
If you need to reinstall Mac OS X and you’ve been using Time Machine to back up your applications, files, and user settings, you can easily restore this information from your Time Machine backup disk after you’ve reinstalled Mac OS X.
Nancy, here is the contact information if you need technical assistance to get your iMac up and running.
Intel-based iMac - Contact Support - Apple Support
http://www.apple.com/support/imac/intel/contact/
Good luck!
- Judy

My macbook 13' (older version) starts only to white screen with apple logo tried to rebooot by pressing shift at the opening but it didn't finish starting before stopping please help anybody please

is anbody there how does this work never done it before my macbook won't start past white screen with apple logo any ideas ?

Are you using a 10.6 Snow Leopard Install DVD? If yes, you can erase and install following these directions: http://support.apple.com/kb/HT3910
You'll know whether or not it is a hard drive issue when you get to step 8 under "Part One: Erasing the hard drive". If you do not see your hard drive in the list on the left side of the Disk Utility window then you know the Mac isn't seeing it—could be a loose cable, but more likely hard drive failure.
If you can see it on the left, click on it and look at the bottom of the Disk Utility window. If you see something like "S.M.A.R.T status: failing" that is definitely a hard drive issue. Otherwise, you can just follow the directions for an erase and install!
Might be worth fixing depending how much a repair would cost. Genius Bar could at least diagnose it for you and give a repair estimate. I'd look at what a new or refurbished one with your same specs would cost though to see if the price differential is worth it...

Pod Freezes Then Goes Onto A White Screen Then Apple Logo Screen, Should I Bring It To Best Buy?

Similar Messages

Maybe you are looking for