PoE and the WAP4410N - need a recommendation...

Looking for a Cisco, low-cost power injector solution to push the WAP4410N. Network is all cat6 and the AP is 100ft away...
Thanks, Mark
I'm long on Cisco - I believe in the future...

Hi, My name is Eric Moyers. I am a Network Support Engineer in the Cisco Small Business Support Center. Currently there are no PoE injectors that are certified to work with any of the Small Business Access Points. The current recommendation is to purchase a small unmanaged switch, similar to the SD208P.
Cisco does recognize that this is a need of our customers and we are currently developing one specifically for these devices, Sunfortunately there is no known timeline for when this will be available.
There are some currently available through Cisco Enterprise and other 3rd party vendors, however we can not guarantee that they will work or not damage your unit.
I hope that this answers your question. Please let me know if I can provide any further assistance.
Eric Moyers
Cisco Network Support Engineer
CCNA, CCNA-Wireless
1-866-606-1866

Similar Messages

I use itunes on a Dell XPS502 with W7/64. In some cases have have problems to import CD's. The sound is very disturbed and the import need a lot more time than in normal cases. Is there a problem between itunes W7/64 or a known hardware issue?

I use itunes on a Dell XPS502 with W7/64. In some cases have have problems to import CD's. The sound is very disturbed and the import need a lot more time than in normal cases. Is there a problem between itunes and W7/64 or a known hardware issue?
Example-CD : "Tracy Chapman , Telling stories" is not able to import . I have more such negative cases. But in other cases it works fine and the sound is great.
The firmware at the inbuild CD/DVD DS-6E2SH is the latest version.
What can I do??

hi b noir,
I don't no about virtuel drives like you mententioned. In the mean time I have rebooted the XPS and run again the iTunes diagnostics. I think the back - chance in the registry was not ready to use. Now there are another results. They are the same in case of a running CD or a not running CD. The difference in total is like before. It takes more time that iTunes reads the (bad) CD and at the there is no good sound. In both cases ( running or not running CD) iTunes diagnostics gives as a result :
(the copie from ITunes shows the result of the not running CD from Tracy Chapman)
Microsoft Windows 7 x64 Ultimate Edition Service Pack 1 (Build 7601)
Dell Inc. Dell System XPS L502X
iTunes 10.3.1.55
QuickTime 7.6.9
FairPlay 1.11.17
Apple Application Support 1.5.2
iPod Updater-Bibliothek 10.0d2
CD Driver 2.2.0.1
CD Driver DLL 2.1.1.1
Apple Mobile Device 3.4.0.25
Apple Mobile Device Treiber 1.55.0.0
Bonjour 2.0.5.0 (214.3)
Gracenote SDK 1.8.2.457
Gracenote MusicID 1.8.2.89
Gracenote Submit 1.8.2.123
Gracenote DSP 1.8.2.34
iTunes-Seriennummer 00D7B2B00CD25750
Aktueller Benutzer ist kein Administrator.
Aktuelles Datum und Uhrzeit sind 2011-06-11 19:33:22.
iTunes befindet sich nicht im abgesicherten Modus.
WebKit Accelerated Compositing ist aktiviert.
HDCP wird unterstützt.
Core Media wird unterstützt.
Info zu Video-Anzeige
NVIDIA, NVIDIA GeForce GT 540M
Intel Corporation, Intel(R) HD Graphics Family
**** Info für externe Plug-Ins ****
Keine externen Plug-Ins installiert.
iPodService 10.3.1.55 (x64) arbeitet zurzeit.
iTunesHelper 10.3.1.55 arbeitet zurzeit.
Apple Mobile Device service 3.3.0.0 arbeitet zurzeit.
**** CD/DVD-Laufwerkstests****
LowerFilters: PxHlpa64 (2.0.0.0),
UpperFilters: GEARAspiWDM (2.2.0.1),
D: PLDS DVDRWBD DS-6E2SH, Rev CD11
Audio-CD im Laufwerk
11 Titel auf der CD gefunden, Spieldauer: 42:07 auf Audio-CD
Titel 1, Startzeit: 00:02:00
Titel 2, Startzeit: 03:59:47
Titel 3, Startzeit: 07:19:27
Titel 4, Startzeit: 11:31:30
Titel 5, Startzeit: 15:31:50
Titel 6, Startzeit: 20:07:50
Titel 7, Startzeit: 24:27:15
Titel 8, Startzeit: 27:49:10
Titel 9, Startzeit: 32:41:25
Titel 10, Startzeit: 35:29:65
Titel 11, Startzeit: 38:38:00
Audio-CD erfolgreich gelesen (Suche nach alter Firmware).
Laufwerksgeschwindigkeit erfolgreich erkannt
Die CDR-Geschwindigkeiten des Laufwerks sind: 4 10 16 24
Die CDRW-Geschwindigkeiten des Laufwerks sind: 4
Die DVDR-Geschwindigkeiten des Laufwerks sind: 4
Die DVDRW-Geschwindigkeiten des Laufwerks sind: 4
After starting the import it is going slower and slower. If it is helpful I can send you a soundfile with these distortions.
best regards
tcgerd

My iPods camera, speaker don't work and the battery needs to be replaced, if I send it into apple will they fix it all?

My iPods camera, speaker don't work and the battery needs to be replaced, if I send it into apple will they fix it all?

Apple will exchange your iPod for a refurbished one for $199 for 64 GB 4G and $99 for the other 4Gs. They do not fix yours.
Apple - iPod Repair price
You can do it an an Apple store by:
Apple Retail Store - Genius Bar
or sent it in to Apple. See:
Apple - Support - iPod - Service FAQ

We have a new nano "5" and after fully recharging it, it drains out after 24 hrs with a few hrs use and the message "need to restore in itunes" appears. what gives?

we have a "new nano 5" and after fully recharging it, it drains out after 24 hrs with a few hrs use and the message "need to restore in itunes" appears. what gives?

akemma wrote:
we have a "new nano 5"
iPod Models

Syncing iPhone and Mac and the room needed on iPhone

Evening Forum
is it me or when syncing my iPhone do i notice that the room needed to swap stuff over is used in a strange way?
for example [and its not exact i know so go with my sizes here], my 32GB iphone has say 30GB left after apps and other things, if i transfer 20GB of music and associated stuff, i have 10GB left. If now i sync a few weeks later with another 28GB of music, as my mac would tell me, despite my thinking that the iphone would know that off coems 20Gb and on goes 28GB, it cant handle that. its seems to need a certain amount of space actually on the i[hone outside of the music being taken off and the music being put on, to actually do the swap.
anyone else found this? whats the exact reason for it? whats it doing?
even if some of those tracks being swappped were the same, thus the tracks not needed to be taken off, surely the iphone should know this. It takes long enough to think about it?

Welcome to Apple Support Communities
Macs use a different version than a iPhone, iPad or iPod touch, so you have to buy this app in the Mac App Store. After installing it, you can sync them if the app has got a sync service or iCloud compatibility. Note that the app for Macs should have iCloud support too

SOAP Encoding and the real need

I just read the below from the site here-
SOAP encoding has fallen out of favor in the Web services community. It is not supported by the WS-I basic profile. So JAX-WS, as the latest incarnation of Java Web services, has disallowed SOAP encoding. JAX-RPC supports SOAP encoding, so if you really must use SOAP encoded messages, stick with JAX-RPC.
I am new to Web Services and am familiar with DOC/Literal only.
Why will anyone want to create a "new" Web service in Encoded format?
What was the real need SOAPEncoding has served when there is a separate standard named XML Schema?
Just curious to explore-

Hello,
The WS-I work constrains the various web service specification to a
functional subset that exhibit the greatest degree of interoperability;
certainly there are many other features (quality of service, security,
attachments, etc.) that are provided by WebLogic web services; this does
not negate the fact that BP 1.0 compliance can be easily achieved.
Regards,
Bruce
Vasudev Kumarjiguda wrote:
>
Hi,
The Basic Profile 1.0 forbids SOAP encoding, yet Bea WebLogic documentation mentions
that RPC-oriented WebLogic Web Service operations use SOAP encoding.
Am I missing something here (since Bea supports the Basic Profile 1.0) ?
thanks
Vasu

I have a I pod touch and when I plug my iPod in to charge A screen pops up and says tempterture. And the iPod needs to cool down. What should I do? It says that no matter what plug I use

M

- Try a reset.
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Then try restoring the iPod.
- If still problem that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.

Ipad mini was locked and the wrong passcode was entered enough to disable it. Tried to connect to a laptop but it says it is locked and the passcode needs to be entered, but I can't because the device says it is disabled.

I tried next to put device into recovery mode and reset it that way but it still said the same thing, itunes says I need to enter passcode to unlock it but the iPad says it is disabled. What can I do next?

FORCE IPAD INTO RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTune (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port. Do not release button until you see picture of iTune and plug (very important)
5. Release Home button.
ON COMPUTER
6. iTune has detected iPad in recovery mode. You must restore this iPad before it can be used with iTune.
7. Select "Restore iPad"...
Note: Data will be lost

I keep getting the message "error signature" and the itunes needs to close

i keep getting the message "error signature" and iTunes needs to close. please help.

Hi johnbpl,
It sounds as if you are having difficulty connecting to the App Store to check for updates for applications on your iPad. If that is the case, I would suggest that you troubleshoot using the steps in this article -
Can't connect to the iTunes Store - Apple Support
Start with the section Troubleshoot issues on an iPhone, iPad, or iPod touch then if needed the section Learn more.
Thanks for using Apple Support Communities.
Best,
Brett L

Smart paging Question , What happen if i don't enable smart paging and available Memory is about 1GB and the VM need 3GB for Booting ?

Hi ,
I configure a dynamic memory With 512 MB for a VM , and available memory 1GB
what happen when I boot the VM , While it actually need 3GB for booting - Note I don't configure Smart Paging ?
Thanks.

You won't be able to boot at all.
pagefile and dynamic memory only comes into play when you don't have enough memory on the host, to support the 'startup RAM' on the VM, and when the VM does a
reboot.
-kn
Kristian (Virtualization and some coffee: http://kristiannese.blogspot.com )

Is there any way to save data(pictures and videos) on a iPhone 3GS with no backup and the battery needs replaced?

I have an iPhone 3GS, the battery is dead and needs replaced. Is there any way to have the battery replaced and save all the photos and videos that are very important of family and friends that are irreplaceable on it? There has been no back up done on the phone that I know of. Thanks for any help you can give me.

I have to think you have tried operating the iPhone with the charging cable plugged into a charger and outlet or USB. It is likely you have tried this and it failed to operate. Have you tried a Reset on the iPhone to see if that will cause the battery to function ling enough to do an iCloud backup or iTunes backup?

SG-300 52p POE and the case of Native vlan forgotten on a Port-channel

Hi
We have recently changed our access switched to Cisco Small Business SG-300 52p on which is working firmware
SW version 1.3.5.58
We found out a very annoying problem on Port-channel and default vlan topic.
Our switch have a default vlan diffrent to the vlan 1 that depends on the floor they are, and this native vlan is at first defined on the portchannel of our central switch, a Cisco 3750
Example of a central switch port-channel with a define native vlan:
interface Port-channel2
description TO 1F
switchport trunk encapsulation dot1q
switchport trunk native vlan 6
switchport trunk allowed vlan 4-6,11,13
switchport mode trunk
on the SG300 side the configuration is this:
interface Port-channel2
description 1F
switchport trunk allowed vlan add 4-5,11,13
!next command is internal.
macro auto smartport dynamic_type switch
As you can see there is no "switchport trunk native vlan 6" simply because the SG300 once i write it on the command line, it accepts the command but the command sentence is not written on the conf (why?!)
the result is that everytime the SG300 is restarted on the port-channel i got two AUTO CREATED commands on the configuration "
switchport trunk native vlan 1
switchport default-vlan tagged
that let not work the network on that floor until i manually write on the SG300
no switchport default-vlan tagged
switchport trunk native vlan 6
These command, as said, works once i write them but are not viewed on a "sh run" and so saved on the conf so every time SG 300 is restarted i need to re-write them.
Is this a bug?
have i made some mistake?
Please let me know
regards
Pietro

Figure out!
the problem was on macro i have to write this:
macro auto processing type switch disabled
and then everything starts going as it should be
Regards
Pietro

Render Queue in AME won't start, tried everything and the client needs the footage! Can anyone Help?

Hi,
I am exporting a quicktime file H.264 at 720p but cant seem to render the video. I have read through heaps of forums and have tried the following:
-Added black video (from premiere) to the video track 1 for entire length of work bar.
- ticked use preview files. and rendered all video, audio and effects before exporting.
- un-ticked include xmp
- tried exporting without audio.
- tried only a few seconds of footage
- tried adding a single opacity keyframe to the first frame of the sequence
- played around with the quality of the clips.
- I've even tried making a new project with just a 10 second clip.
Each time After about 10 minutes of waiting I finally get an error msg as below:
- Source File: /Users/StudioB/Library/Caches/TemporaryItems/Untitled.prproj
- Output File: /Users/StudioB/Desktop/Sequence 03.mov
- Preset Used: Custom
- Video:
- Audio:
- Bitrate:
- Encoding Time: 07:13:59
Mon Mar 22 18:29:58 2010 : Encoding Failed
Could not read from the source. Please check if it has moved or been deleted.
I haven't moved any files and haven't had a problem with rendering the sequence in premiere. but i have had multiple crashes when altering audio
track properties (adding compressors etc.)
The project file and media was originally copied from CS3 on quad core pc (win xp) and is now running on Mac Pro Dual quad OS X CS4 version 4.0.0
I am really stuck for a solution. Can anyone offer a suggestion?

Please try to trash your prefs and clear your media cache as well.
http://blogs.adobe.com/genesisproject/2009/11/having_weird_behavior_with_an.html

My laptop need a replacement f0r the audi jack, keyboard, and the screen

its a hp LT G62 -339WM
AMD ATHLON II P320
HEWLETT PACKARD COMP
the screen is broken and the keyboard need some letters, the audio jack is broken and i need too know if its posible change all parts , please tellme how or how much is the cost

You can find all your part numbers, and how to replace them here in the "Maintenance & service guide" http://h10025.www1.hp.com/ewfrf/wc/manualCategory?cc=us&dlc=en&lang=en&lc=en&product=4308426&task=

Which switch for POE and 7940G phones?

I have 2 (and maybe soon 5 more) 7940G phones to add to my network, which already has a Netgear POE capable switch. I've since discovered that early Cisco POE isn't the same thing as current POE, and the switch doesn't power the phones.
I was looking at adding a Cisco SD208P 8-port switch to power the phones, but I soon discovered it only has 4 POE ports, and I'm not sure that this switch will even power the 7940G phones. And if the other 5 phones show up, I'll need two of those switches with no room for expansion on the voice network.
Will this switch power those phones?
Is there another small switch available so I don't have to replace my existing switch infrastructure to get these phones to work? Or do I need to scrap the phones and get something newer that will work with the current POE standards?

Will,
I would look at the ESW520 8 port switch, it will power the phones and will have the "*" VLAN's already setup in them.
Side note "*": This assumes that you are using VLAN100 and Cisco Voice system for the switch
Have a great day

PoE and the WAP4410N - need a recommendation...

Similar Messages

Maybe you are looking for