PoE for Cisco 1242AG and 1310G Access Points

Dear All,
we purchased a Cisco 1242AG and a 1310G Access Point and in the DataSheet it was specified that these APs support Power-over-Ethernet. The problem is we don't see any RJ-45 port in either AP which could be used for connecting the AP to an PoE Switch. Can you please tell us how we can connect these APs to an 802.11af compatible PowerBridge (by Intermec) ? Thanks.

Hi Thorsten,
The 1242 should be good to go but the 1310 is powered quite differently. Have a look;
AP 1240 Series - Hardware (see diagram)
http://www.cisco.com/en/US/products/ps6521/products_installation_guide_chapter09186a008079b7f4.html#wp1071972
Connecting the Ethernet and Power Cables
http://www.cisco.com/en/US/products/ps6521/products_installation_guide_chapter09186a008079b7f4.html#wp1052781
1300 Series Power
Power
The access point/bridge receives inline power from the Cisco Aironet Power Injector (hereafter called the power injector). Dual-coax cables are used to provide Ethernet data and power from the power injector to the access point/bridge. The power injector is an external unit designed for operation in a sheltered environment, such as inside a building or vehicle. The power injector also functions as an Ethernet repeater by connecting to a Category 5 LAN backbone and using the dual-coax cable interface to the access point/bridge.
The power injector is available in two models:
Cisco Aironet Power Injector LR2 standard version (included with the access point/bridge)
48-VDC input power
Uses the 48-VDC power module (included with the access point/bridge)
Cisco Aironet Power Injector LR2T optional transportation version
12- to 40-VDC input power
Note The power injector and the power module must not be placed in an outdoor unprotected environment. The power module must not be placed in a building's environmental air space, such as above a suspended ceiling.
http://www.cisco.com/en/US/products/ps5861/products_installation_guide_chapter09186a008079b93b.html#wp1051840
Dual coaxial cable to run from the power injector to the 1300. See attached notes:
Cisco Aironet 1300 Series
Cisco Aironet 1300 Series Access Point/Bridge Power Injector
The Cisco Aironet 1300 Series Outdoor Access Point/Bridge Power Injector,converts the standard 10/100 BaseT Ethernet interface that is suitable for weather protected areas to a dual F-Type connector interface for coax cables that are more suitable for harsh outdoor environments. The Power Injector also provides power to the outdoor unit over the same cables with a power discover feature and surge protection. To support longer cable runs from your wireless network switch or router, the Power Injector LR is designed to accommodate up to a 100 meter coaxial cable run plus 100 meters of indoor cat5 cable?enabling total cable runs up to 200 meters. The Cisco Aironet 1300 Series Outdoor Access Point/Bridge ships with the Power Injector LR2 and an AC power supply.
From this link:
http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a008022551d.html
Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide
Ethernet Ports
The access point/bridge dual-coax Ethernet ports consists of a pair of 75-ohm F-type connectors, linking the unit to your 100BASE-T Ethernet LAN through the power injector. The dual-coax cables are used to send and receive Ethernet data and to supply inline 48-VDC power from the power injector to the access point/bridge.
From this link:
http://www.cisco.com/en/US/products/ps5861/products_installation_guide_book09186a00804d3095.html
AIR-PWRINJ-BLR2
F-Type Connectors
Dual coaxial cable carries full-duplex Ethernet, DC power, and full-duplex console port (RS-232 connection)
From this link:
http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a00802252e1.html
Hope this helps!
Rob

Similar Messages

Image Recovery for Cisco Aironet 1300 Outdoor Access Point

We purchased two 1300 APs for outside. There is a new release for the image that we wanted to use so, we have the latest security updates. We downloaded, logged onto the access point just fine, but the image never took. After four hours with a direct connection, it was still going and this morning we came in and it just keep rebooting. Our network guy states it looks like a corrupt image. We can barely do anything and since there is no "mode" button like the earlier models, I have not found anything on web sites or forums to help us reload a good image to the access point. I would appreciate any insight someone has and/or where to look for this. I logged on and downloaded about every manual on the 1300 I could find, but have not found a good way to fix this. Not even the upgrade tool will connect since it just keeps rebooting.

Hi Bruce,
Because (as you correctly noted) the 1300 does not have a mode button you could try this method;
Complete the steps in this section in order to reset Cisco IOS Software-based bridges:
If the privileged command prompt ap# is available in the CLI, the write erase command and the reload command erase the startup configuration and reset the unit.
If the GUI is available, choose System Software > System Configuration. Press the Reset to Defaults button.
Aironet 1300 Series Bridges do not have a MODE button to reset the AP to factory defaults. So, if neither the GUI or CLI is available with sufficient privileges, complete these steps to delete the current configuration and return the entire bridge settings to the factory defaults using the CLI.
Open the CLI with a Telnet session or a connection to the bridge console port.
Reboot the bridge by removing and reapplying power.
Allow the bridge to boot until the command prompt appears and the bridge begins to inflate the image.
Press ESC when you see lines that are similar to these on the CLI:
Loading "flash:/c1310-k9kw-7mx.v122_15_ja.200040314-k9w7-mx.v122_15_ja.20040314"
...#############################################################################Note: In order to access the boot loader, you must press ESC twice. But this action depends on the terminal-emulation software that you use.
Messages that are similar to these appear:
Error loading "flash:/c1310-k9kw-7mx.v122_15_ja.200040314-k9w7-mx.v122_15_
ja.20040314"
Interrupt within 5 seconds to abort boot process.
Boot process terminated.
The system is unable to boot automatically. The BOOT environment variable needs to
be set to a bootable image.
C1310 Boot Loader (C1310-BOOT-M), Version 12.2 [BLD-v122_15-ja_throttle.20040314 100]
bridge:At the bridge: prompt, issue the dir flash: command in order to view a directory of the Flash file system.
The directory is similar to this directory:
bridge: dir flash:
Directory of flash:/
2 -rwx 0 env_vars
5 drwx 384 C1310-k9w7-mx.v133_15_JA.20040314
3 -rwx 1128 config.txt
4 -rwx 5 private-config
3693568 bytes available (4047872 bytes used)
bridge:Delete or rename the files config.txt and env_vars, and reboot the bridge.
Note: Do not forget the / character before the filenames.
bridge: delete flash:config.txt
Are you sure you want to delete flash:/config.txt (y/n)?y
File "flash:/config.txt" deleted
bridge: delete flash:/env_vars
Are you sure you want to delete "flash:/env_vars" (y/n)?y
File "flash:/env_vars" deletedIssue the boot command in order to reboot the bridge at the bridge: prompt, or simply power cycle the bridge.
After the bridge reboots, reconfigure the bridge with the web browser interface, the Telnet interface, or Cisco IOS Software commands.
Note: The bridge is configured with the factory default values that include:
The IP address, which is set to receive an IP address with DHCP. If you do not have a DHCP server, you can access the bridge using the default IP address of 10.0.0.1 using HTTP/HTTPS or Telnet. Once you gain access to the bridge via Telnet or GUI, you can modify the IP address of the bridge.
Note: This default IP address of 10.0.0.1 becomes available only for a short period. So, make sure that you assign your own IP address to the bridge within that period of time.
The default username and password, "Cisco".
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/products_password_recovery09186a00800949d0.shtml#ca_1310_ser
One other thing, be careful with the new IOS that you aren't loading a LWAPP Recovery Image. (it almost sounds like what may have happened)
Hope this helps!
Rob

Cisco 802.11n Outdoor Access Point

I have to propose to a client a 802.11n outdoor Acess point with external antenna, tha gain must be >8 dbi.
Which cisco model should i use ?

I have to propose to a client a 802.11n outdoor Acess point with external antenna, tha gain must be >8 dbi.
DO NOT, under any circumstances, use 1260 or 3500e if you plan to use antennas > 6 dBi. These two models DO NOT SUPPORT antenna gain higher than 6 dBi. The only two 802.11n-capable WAP that can support high-gain antenna of > 6 dBi are the 1250 and the 3500p.
Antenna Product Portfolio for Cisco Aironet 802.11n Access Points
The 1250 is End-of-Sale (End-of-Sale Date: 12 January 2012) and requires 20.0w of PoE. The 1250 can support antenna gain > 6 dBi.
The 3500p was released around mid-2011 because people were howling/screaming about the lack of high-gain antenna support, thus the 3500p was developed alongside the AIR-ANT25137NP-R.
Cisco recommends that the installation of the AIR-ANT25137NP-R should be done with proper sight-survey.
[Sorry Scott. Didn't want to be rude. ]

Cisco Outdoor Controller Based Access Point

Hi,
I am looking for Cisco Outdoor Controller Based access point model. The WLC is Cisco 2500 Series.
I have checked couple of outdoor models but all are mesh access point. I am looking for normal controller based outdoor access point ( just like controller based indoor access point models )
Thanks.

adding to Leo...
Cisco Aironet 1300 Series
http://www.cisco.com/en/US/products/ps5861/index.html
Cisco Aironet 1550 Series
http://www.cisco.com/en/US/products/ps11451/index.html
Cisco Aironet 1520 Series
http://www.cisco.com/en/US/products/ps8368/index.html
these all are Cisco OUTdoor APs.
Now u can choose as per ur req.
Regards
Dont forget to rate helpful posts

Dynamic VLAN Assignment with RADIUS Server and Aironet Access Points

Hi Guys,
I would like to go for "Dynamic VLAN Assignment with RADIUS Server and Aironet Access Points 1300". I want the AP to broadcast only 1 SSID. The client find the SSID ->put in his user credential->Raudius athentication->assign him to an specific vlan based on his groupship.
The problem here is that I don't have a AP controller but only configurable Aironet Access Points 1300. I can connect to the radius server, but I am not sure how to confirgure the AP's port, radio port, vlan and SSID.
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml#switch
I go through some references:
3.5 RADIUS-Based VLAN Access Control
As discussed earlier, each SSID is mapped to a default VLAN-ID on the wired side. The IT administrator may wish to impose back end (such as RADIUS)-based VLAN access control using 802.1X or MAC address authentication mechanisms. For example, if the WLAN is set up such that all VLANs use 802.1X and similar encryption mechanisms for WLAN user access, then a user can "hop" from one VLAN to another by simply changing the SSID and successfully authenticating to the access point (using 802.1X). This may not be preferred if the WLAN user is confined to a particular VLAN.
There are two different ways to implement RADIUS-based VLAN access control features:
1. RADIUS-based SSID access control: Upon successful 802.1X or MAC address authentication, the RADIUS server passes back the allowed SSID list for the WLAN user to the access point or bridge. If the user used an SSID on the allowed SSID list, then the user is allowed to associate to the WLAN. Otherwise, the user is disassociated from the access point or bridge.
2. RADIUS-based VLAN assignment: Upon successful 802.1X or MAC address authentication, the RADIUS server assigns the user to a predetermined VLAN-ID on the wired side. The SSID used for WLAN access doesn't matter because the user is always assigned to this predetermined VLAN-ID.
extract from: Wireless Virtual LAN Deployment Guide
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00801444a1.html
==============================================================
Dynamic VLAN Assignment with RADIUS Server and Wireless LAN Controller Configuration Example
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml#switch
==============================================================
Controller: Wireless Domain Services Configuration
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801c951f.shtml
Any help on this issue is appreicated.
Thanks.

I'm not sure if the Autonomous APs have the option for AAA Override. On the WLC, I can go into the BSSID, Security, Advanced, and there's a checkbox that I would check to allow a Radius server to send back the VLAN.
I did a little research and it looks like the 1300 may give this option but instead is defined as "VLAN Override". I've found the release notes for 12.3(7)JA5 (not sure what version you're running) that give mention and a link to configuring EAP on page 4: http://www.ciscosystems.ch/en/US/docs/wireless/access_point/1300/release/notes/o37ja5rn.pdf
Hope this helps

Cisco module controller & 1131 access-point

I'm using a blade as a controller in a cisco router. trouble is it does not see
the 1131 access-points. does see 1020 access points. Any thoughts

If you are using OP 43 to tell the access points where to find the controllers you will need a new entry for the 1130 series of access points.

Wlc 5508 and 40 access point 1141n disturbance in the temp response

Hello,
i have a wlc 5508 and 40 access point 1141n
there are 1500 users connected with this controller 5508.
but when i ping at my gateway ,there is a disturbance in the temp response .
Here below a snapshot:
Réponse de 172.16.1.1 : octets=32 temps=1 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=5 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=2 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=56 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=105 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=433 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=1 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=100 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=300 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=466 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=711 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=900 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=55 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=52 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=54 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=200 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=57 ms TTL=55
Réponse de 172.16.1.1: octets=32 temps=800 ms TTL=55
anyone help me?
thx

Looks to be wither a duplicate address issue or a configuration issue. Try to test with only using the 2.4ghz and then again with only the 5ghz and see if you see a difference.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

Vsphere/ESXi 5.0 update 2 iso for Cisco Blade and Rackmount Servers.

Hello Team,
Can someone provide me details of Vsphere/ESXi 5.0 update 2 iso for Cisco Blade and Rackmount Servers.
I tried to find it on both Cisco and Vmware websites but without success.
It would be good if you can please share the links.
Regards
Deepak Jha
+91-9873005405

Deepak,
From Padma's link, I found 5.0 U1, and found U2 here:
https://my.vmware.com/web/vmware/info/slug/datacenter_cloud_infrastructure/vmware_vsphere_hypervisor_esxi/5_0#product_downloads
I want to say, that U2 is not the customized image though
-Kenny

Can anyone recommend a good document for Cisco IDS and AAA

I need some basic tutorial for Cisco IDS and AAA. can anyone recommend any document for it?
thanks

The Cisco IDS/IPS senors do not perform any AAA functions. You can not validate a user/password externally.

Help required to implement Cisco 2504 WLC and 1042 Access Points

Hi,
My name is Vidya Sagar. I am new to Wireless technology. We are planning to implement Wireless in our office. I have given the requirements below. Kindly go through the details and let me know how to start.
We have purchased Cisco 2504 Wireless Controller (One) and Ciscon 1042 Access Points (Five). At present I am going to use 3 access points only.
I have attached a simple diagram of our office network. We have more than 30 VLANs configured in Core Switch, we are planning to give wifi access to only 3 VLANs.
1. VLAN 121 ( IP Segment - 10.52.121.0 /24)
2. VLAN 116 ( IP Segment - 10.52.116.0 /24)
3. VLAN 100 ( IP Segment - 192.168.100.0 /24) (Guest)
Please give me a implementation plan to do this. I would like to use LDAP or ACS for authentication purpose.
Regards,
Vidya Sagar

Lets just do this simple first before you start using ACS as that will require a certificate installed on the ACS for using PEAP.
So first off, the WLC we will say is in vlan 10. When you are going through the startup wizard, make sure you define the vlan tag to 10 on the management interface. Make sure your virtual interface is an IP address that is not routed in your network, like an out of band IP.
Make sure the WLC time is correct or use NTP!!!!
Now you should be able to http or https to the WLC. I would upgrade the code to v7.4 and install the FUS image. Please reference this link for the upgrade procedure. You don't have to upgrade now... I would wait till you get everything working first.
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn74.html
Now I would connect the APs on the same vlan as the WLC for now. Make sure there is dhcp on that subnet. Once the APs have joined, then you can move them to any subnet you want. Since you don't have many APs it would be okay to leave them in the same vlan as the WLC management or out them on any other vlan you choose. The APs will be connected to an access port NOT a trunk port!!!!
The WLC will need to be connected on a dot1q trunk port only allowing vlans 10,100,116,121. The 2504 running v7.4 will support LAG (etherchannel). Any ways, your switch port should look like this for example only
Interface gigabit1/0/1
description WLC2504
switch port trunk encapsulation dot1q
switchoort mode trunk
switch trunk allowed vlans 10,100,116,121
spanning-tree portfast trunk
channel-mode group 10 mode on << only for v7.4 if you use lag
Don't connect all four ports right now, just port one!!!!
Your Guest vlan, you will need to create an ACL to block traffic from accessing the internal network. You might want to allow dhcp and DNS bit I would leave it open first until you can verify everything is working.
Now on the WLC you need to create a dynamic interface for vlan 100, 116, and 121. If you click on the Controller tab in the GUI and click on interfaces on the left hand side, that will take you to where you can add/delete/modify your interfaces. When creating these interfaces, make sure you add the dhcp server IP address for the primary and or backup.
Now that you have your dynamic interfaces created, its time I create your SSID. Now click on the WLAN tab on the GUI and click on WLAN and then on the too right select Create New and then click go. Select WLAN on the drop down menu and then for the profile name I would use the SSID name also for simplicity.lean e the WLAN id to 1 for this and 2 for the next and so on. After defining these and clicking Apply you can now define your SSID. On the General tab, enable the status and leave the radio policy to all for now, you can decide later what you want to use. Choose your interface you wan to place this SSID on and enable Broadcast SSID for now and leave everything else alone. Now click on the Security tab and on the layer 2 Security, leave it at WPA + WPA2, only check WPA2 Policy and for WPA2 encryption choose AES only. Now go to the bottom of that screen and choose PSk. We will do pre shared key for now so you get to understand the setup and make sure everything is working first. Now on the PSK format, choose ASCII and put your pre shared key in the input box. Make this simple to for testing. You don't want to put in symbols or anything like that. When you are don with that, check apply on the top right and test.
Now you can repeat this with your other SSIDs just to test. Your guest network you can leave open for now to test open authentication.
Here are some links for the WebAuth feature:
https://supportforums.cisco.com/docs/DOC-13954
http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a0080b1a506.shtml
Now if you want to use ACS with PEAP, here is some links for that:
https://supportforums.cisco.com/videos/2499
http://www.cisco.com/en/US/products/ps10315/products_configuration_example09186a0080bd1100.shtml
https://www.google.com/url?sa=t&source=web&cd=8&ved=0CFQQtwIwBw&url=http%3A%2F%2Fwww.youtube.com%2Fwatch%3Fv%3DWk_bRdmsQlA&ei=_BEyUeCYM8TdqAHHsICAAw&usg=AFQjCNF8PiVBQK1Kipb4j8AzD153bKtmgA&sig2=smHhNVmCr2of2NzbnDhGmw
Well that is it, hopefully you can get the wireless up for testing and verifying everything works!
Sent from Cisco Technical Support iPhone App

SG300-28P and aironet access points

Dear support,
does Cisco SG300-28P provide enough PoE to power access points 1550 and 1600?
Thank you

Hi Mireille, it should. The 1550 is 802.3af compliant.
The 1600 may be interesting because it can actually draw up to 15.4 watt of power and you may run into limitations of cable. It is also 802.3af compliant.
-Tom
Please mark answered for helpful posts

Radius local server and wireless access points

Hello to all,
I would like to ask a question related to radius server. I have a Allied telesis core switch and i configure the radius server locally, also i configure the port1.0.7 for dot1x and i am using dynamic vlan. If i connect my laptop to port 1.0.7 i can get the correct ip from the dhcp server. If i connect an access point to the same port , how i should configure the dot1x ? for multiple hosts? I know i am using allied telessis but the config is very similar to the cisco: take a look:
(Radius and nas config)
radius-server host 127.0.0.1 key awplus-local-radius-server
aaa authentication dot1x default group radius
aaa authentication auth-web default group radius
crypto pki trustpoint local
crypto pki enroll local
radius-server local
server enable
nas 127.0.0.1 key awplus-local-radius-server
group Andrew
attribute NAS-Identifier andrew
attribute Tunnel-Medium-Type IEEE-802
attribute Tunnel-Private-Group-Id 10
attribute Tunnel-Type VLAN
user andrew encrypted password wh8q0J2oYSn0y4cynksNCqfbaUtRGv/E6JaJrW+s3Zs= group Andrew
(port config)
interface port1.0.7
switchport
switchport mode access
auth-web enable
dot1x port-control auto
auth host-mode multi-supplicant
auth dynamic-vlan-creation
I tried with auth-web and without but no luck. If someone have a sample config how to configure the dot1x to be able to use access point please paste it.
Thanks
Andrew

I'm not sure if the Autonomous APs have the option for AAA Override. On the WLC, I can go into the BSSID, Security, Advanced, and there's a checkbox that I would check to allow a Radius server to send back the VLAN.
I did a little research and it looks like the 1300 may give this option but instead is defined as "VLAN Override". I've found the release notes for 12.3(7)JA5 (not sure what version you're running) that give mention and a link to configuring EAP on page 4: http://www.ciscosystems.ch/en/US/docs/wireless/access_point/1300/release/notes/o37ja5rn.pdf
Hope this helps

Roaming between RV220W wireless router and WAP121 Access Point

Hello, I have recently purchased a RV220W wireless router and a WAP121 access point and i would like to allow my users to "roam" between the two networks as needed (so when the user is closer to whichever one they connect to that one since it has a better signal). For the most part I only have experience in cisco IOS and in actual routers not the wireless stuff so my knowledge has not exactly transfered over well.

William,
WDS will not work between the RV220W and WAP121 due to incompatible chipsets. The RV220W can be repeated using WDS by another RV220W or RV180W only. You will need to plug the WAP121 into the RV220W or try WorkGroup Bridge mode to repeat the signal.
Regarding roaming, the router or AP are not aware of each other and do not have the capability to disconnect a client and help them connect to the AP with the stronger signal. The client will switch to the stronger AP only when the original signal is lost.
The Aironet (enterprise) devices have the ability to utilize a wireless LAN controller which can help keep devices connected to the stronger signal and allow truly seamless roaming between APs.
- Marty

Westell 327w and Wireless Access Point

I had DSL last year, but have since changed to FIOS, which I love. So I have the Westell 327W modem/router that isn't being used. I have decided to use it in another project for the 4 port ethernet and the wireless capability.
As this other project, we are using another service, which isn't DSL. However, I figured that I could use the 327w as the wireless access point. I currently have access to the internet through the provided internet service and from there I go into a Cisco ASA 5505 firewall. From there I run an ethernet cable to the 327w.
As long as I plug a computer into one of the 4 ethernet ports on the 327w, I'm able to ping to the Internet using either the IP address or using DNS. I'm able to surf and everything.
I have also set up the wireless and using WPA security and I'm able to connect a laptop to the wireless. I get the IP address via DHCP from the ASA, so I have turned off the DHCP server on the 327. I have also turned off the firewall. I then test connectivity and I can ping anything on the network that is assigned by the ASA, but when I try to ping to an Internet address, by the address, I get request timed out. I also don't get anything back on DNS and so forth.
What do I need to do on the 327 to allow the wireless to work with the current connection set up.
Thanks for the help and information.

I got it to work. What I had to do was to set up the 327w in VLAN mode so that the wireless side would send the packets out the ethernet port to the ASA or another router.
In fact, I'm writing this on the wireless setting of the 327w. So setting the VLAN allow the wireless to send and receive packets.

Need some advice for AP IOS upgrade (Wireless Access Point 3702 Series) ?

Hi to all
I recently purchase a Wireless Access Point (AIRCAP 3702E-E) with 4 antenna, i will use this device like wifi hotspot in my home.
I would like to upgrade it but i see two kind of AP IOS :
Lightweight AP IOS Software
Autonomous AP IOS
What are the difference ?
In case of Lightweight AP IOS Software will be the one to choose, i have multiple IOS :
Wireless Lan, ap3g2-k9w8-tar.152-4.JB4.tar
Wireless Lan Recovery, ap3g2-rcvk9w8-tar.152-4.JB4.tar
Someone can tell me what is the difference between these two versions ?
Best Regards.
Elrick.

Hi Elrick,
Cisco AP AIRCAP3702E is Cisco enterprise unit. Cisco small business support WAP4410N, WAP121, WAP321, WAP551, and WAP561 AP. However I will answer your questions.
Lightweight AP ISO you can use it ONLY if you connect AP to wireless controller
Autonomous AP ISO for manage and modify AP by it self not required wireless controller.
Thanks,
Moh

PoE for Cisco 1242AG and 1310G Access Points

Similar Messages

Maybe you are looking for