Polling interval for Topology Services in Cisco Prime 4.2

Hi,
Where can I find the polling interval for Topology Services? I noticed that the devices' status is not updated on the map.

Hi Benjo,
If there are few devices which you are more concerned of then you can add them under CRITICAL poller list.
Check the below link:
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/user/guide/admin/datacollection.html#wp1053692
NOTE:
If the critical set of devices is more than 30, the amount of traffic generated as part of the polling cycle will use a large amount of bandwidth.
Thanks-
Afroz
[Do rate the useful post]

Similar Messages

How to set polling interval for database adapter in interconnect?help plz!!

Hi
i have 4 database adapters with same name subscribing to same event in 4 different interconnect instances(i.e., same business event and application event in different hubs) and pointing to same source application database , same destination application database.
source application database have one oai bridge schema.When a message has to be sent,message will be enqueued in messageobjecttable.This message can be taken by 4 databse adapters.and send to 4hubs then 4 messages will be sent to destination application instead of single message.
To avoid this,I want to set database polling interval in 4 adapters sych a way that if one adapter take message in MESSAGEOBJECT TABLE,the other three adapters don't pick same message.
this way i can avoid redundacy at destination application.Please reply soon
Thanks

You would seem to have an extremely unusual use case for interconnect. The whole purpose of Interconnect is to concentrate the message processing into one hub and distribute the message to those applications interested in it. The use of 4 hubs from one application is probably not supported for precisely the reasons you are having trouble. Can you give us more details of your use case?
I am not sure that adjusting the polling interval for the different adapters will help. Since at some point you will get a collision where 2 or more adapters poll at the same time.

Polling interval for triggering alerts

Is there a way to set the polling interval for alerts. I'm getting 2 alerts for the same message id. I do not want to supress multiple alerts, our alert config scenario is rather generic.

Aamir,
I found this SAP note 913858 that talks about something similar but we are on 7.0 SP9.
Q11: Why do I sometimes receive two alerts when an error happens in a receiver adapter?
A11: This happens because two independant components of the Adapter Framework react simultaneously on the error. The problem will fixed with SP17.
And it seems to stem from the receiver adapter.
Thanks,
Pam

Topology View / Service with Cisco Prime Infrastructure 2.x "PRIME-NCS-APL-K9" ????

Hi Team,
Hope you all doing well.
I just want know few thing about Cisco Prime Infra 2.x.
1st thing is does CPI2.x support Network topology View? if not then is that any other feature which can provide Network View (exa :- Map,etc)?
2nd thing is it possible to take Telnet/Ssh of discovered device from CPI2.x then how we can do that?
3rd Thing if we want to add third party device in CPI2.x then what are prerequisite for the same (Vendor MIB, etc) and procedure?
Your help will be appreciated.
Thanks,
Vishal

Hi Vishal,
Since you don't have any data as such on PI 2.1 , go ahead installed PI 2.2 on the Appliance.
Yes , you need to download , the .ISO image and burned it on DVD and start the installation.
here is the download link::
https://software.cisco.com/download/release.html?mdfid=286236028&flowid=72882&softwareid=284272932&release=2.2&relind=AVAILABLE&rellifecycle=&reltype=latest
You need to check if you are entitle for download or not.
Can we installed PI 2.2 from current PI 2.1 GUI access? No , it is not possible.
check these links for installation step::
http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/2-2/quickstart/guide/cpi_qsg.html#pgfId-43441
http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/2-2/hardware_install/guide/Cisco_PI_Hardware_Appliance_Installation_Guide/cpi_higmain.html#pgfId-1062344
Thanks-
Afroz
***Ratings Encourages Contributors ****

Poll interval for sender file adapter.

I have a 1_sender file NFS file adapter which picks a trigger file from X location in PI application server, this trigger file initiates the unix script present in the sender file adapter.
Unix script brings all the file which starts with 25588* from bank FTP and places in Y location in PI application server then script deletes the "trigger file".
another NFS File adapter 1_receiver file adapter places the trigger file in the X location of PI.
for 1_sender file poll interval given as 86400, that means it should trigger only once a day @ 1:30pm.
But today same sender file adapter had triggered 4 times, could any one let me know the reason why it had triggered 4 times instead of single time.

Vidya,
There are two things :-
1. The polling interval should be 24 hrs;
2. The polling interval should be 24 hrs and it should poll at 1:30 pm every day.
For any reason if the channel is re-started, then with your present configuration, you will never be able to achieve # 2.
So, better use ATP.
But today same sender file adapter had triggered 4 times, could any one let me know the reason why it had triggered 4 times instead of single time.
Might be the connection dropped / failed at the time of polling and the channel re-tried. If you give more details (what time and with how much interval it triggered), someone might be able to help.
Regards,
Neetesh

Limit Number of active sessions for wlan user in Cisco Prime

Is there a way to limit the number of logins from a particular set of credentials in Cisco Prime 2.1? I want to set a maximum of 2 logins from a particular user on the wlan. I have a guest wlan using layer 3 security and an internal wlan using RADIUS (Windows). Would appreciate the help

There is, but it isn't due to PI. It is a function of the WLC itself.
Under Security, there is a Concurrent User Login, set to 0(which is default) it is unlimited logins. This value can be changed to be the number of concurrent logins that work for your situation.
Be advised, this is not a Per WLAN setting, it is a controller wide setting.
HTH,
Steve

Role assignment and FDI polling interval for participant info

Hi,
When a role is added to a participant in Portal Admin console how long it takes to take effect meaning how soon he can login and use the role. Inother words what is the FDI polling interval time to get participant info? I am getting "fuego.portal.exception.WapiOperationException: Participant 'XYZ' does not have execution permissions for role 'ABC' though the Execute permission was given to the user.
Will this role assignment applies for In Flight instances too?
Regards,
Xavier

After you have assigned a particpant to a role and if you are sure you have given execute permission to the partcipant and still if the change doesnt reflect in your application, just try restarting engine. Even if the problem persists then try restarting the weblogic server. The role assignment applies to inflight instances also. for eg : if there are two instances that belong to the role say'ABC' and you have mapped 'XYZ' for that role, then you can see the instances of that role in 'XYZ''s inbox.
Hope this helps.
Regards,
Charan

E-mail will be suppressed up to 30 minutes for these alarms. Cisco Prime

Hi
I'm trying out the email notification in the cisco prime and encountered this issue.
E-mail will be suppressed up to 30 minutes for these alarms.
This causes the other AP's that I restart to not send an notification, and I cannot find a way to remove this email suppression.
I want all the critical emails to be sent and not get dropped.
Or am I misunderstanding this? I cant find any threshold to change / disable
Cisco prime 2.0 fyi
thanks!

This is still a problem in Prime 2.0. I opened a case asking how to change the email suppression time period from 30 minutes to 4 hours so that alarms tripped overnight that won't be acknowledged wouldn't result in a flooded mailbox, and was told this is not a configurable option. So apparently the only "fix" is to turn off the alarm, or change the category to a lesser one that won't result in an email being sent. I hope in a future release they will decide to make this configurable.

Drawing network topology in Cisco Prime LMS 4.2

Hi all:
I installed the Cisco Prime LMS 4.2 and managed to discover the Cisco devices and user devices like my PC stations.
Then I tried to draw the network topology from this LMS 4.2 and I found the topology under the Configuration and Monitor tab. By clicking to these two tabs, it appears a page of something like below:
Topology Services
You can use Topology Services to:
- View detailed xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
- Display the physical and logical services in your network
- xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxx
- xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxx
- xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxx
- xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxx
- xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxx
There is no action click on this page and it looks like an explanation page and cannot do anything.
May I know how to draw the networl topology by this Cisco Prime LMS 4.2?
Hope to hear the answer from anyone know about this soon. Many thanks!
Warmest regards,
tangsuan

Hi Mantej:
Thanks to your link and I have downloaded the Prime LMS 4.2 document.
I then read and installed the JRE first in 64 bits because my Windows OS is 64bits but it still prompts out the Java installation screen. I then installed the JRE in 32 bits.
After that, it has no more Java installation screen. It then request for downloading file at the Windows top bar. I follow the request to riight click to allow the downloading. The Java running and downlaod the file.
After that, I cannot see any difference. Meaning I still cannot access anything for Toplology Services to draw my network topology diagram.
May I know what should be happen and what is the next step to do the topology drawing?
Many thanks!
Regards,
tangsuan

Network topology map Cisco Prime Infrastructure

Hi just want to inquire if it is possible to create a network topology map on cisco prime infrastructure's dashboard that will display both wired and wireless devices or do we need another cisco product to accomplish it.
Thanks

At long last, Prime Infrastructure 2.2 was released yesterday (17 December 2014) and now includes the Topology map feature:
"Cisco Prime Infrastructure provides a visual map that allows you to view the physical network topology, including the network devices and the links that connect them. The topology maps have indicators that show the current alarm status of network devices and links. By using the network topology maps, you can easily monitor your network by viewing alarms and viewing the interconnection between the devices." (Link)
I'm migrating a system now and will open a new thread with first impressions.

Is cisco prime infrastructure support / can be run as syslog server?

Dear All,
is cisco prime infrastructure support / can be run as syslog server?
and,
where i can see network topology diagram, using cisco prime infrastructure?
many thanks,
Jerri

Hello. Cisco Prime LMS will be replaced by Cisco Prime Infrastructure in the near future.
In the current release of Cisco Prime Infrastructure you can't use topology diagrams. This feature is in roadmap.
About syslog, you can send syslogs to Cisco Prime Infrastructure, but I don't recommend using it as syslog server. Please see this link for more information https://supportforums.cisco.com/thread/2179520
Please rate if this helps

Defining polling interval on customization file

Hello everyone,
I have a requirement: define a polling interval (in this specific case for a email polling proxy, however it would be useful for a file polling proxy as well) in a customization file.
It seems a simple task, however i could not find a way to perform...
I've searched here in the forums and have found nothing (if someone finds a thread about this please provide the link).
I've googled a bit as well, and the result was the same...
In this blog post http://wesselj.blogspot.pt/2012/01/oracle-service-bus-good-bad-and-ugly.html we can read:
"+(...) Customization files. Inflexible, verbous and complex to maintain. Not everything can be customized with the customization files, some like passwords are reasonable, *but things like polling interval for file integration would be nice to be able to change between environments*.+"
And in this document http://docs.oracle.com/cd/E11036_01/alsb30/pdf/consolehelp.pdf , in the customization topic (page 29-1), there is nothing mentioning polling interval...
The environment installed is OSB 11gR1.
Any suggestions on how to perform this task?

Any ideas?

JDBC sender adapter polling data more than once within one polling interval

Hi,
Our sender communciation channel is polling data twice in one polling interval, hence triggering the corresponding BPM twice.
The polling interval for the channel is set to 30 mins.
We dont have an update query and use <test> instead. Currently there is no provision to use an update query in the source system.
Intermitently the polling happens within an interval of few milliseconds, because of which we are in doubt whether the use of Update query will solve our problem
Additionaly in the BPM, we have one channel which deletes the data from source system after the processing is complete by the BPM, but the second BPM is getting triggered before the deletion step is being executed in the first BPM.
Please Advise how we can stop the channel from polling data twice.
Thanks,
Merrilly.

Hi Merrilly,
Please ty to set an advanced mode option in the table(for sender
channel configurations) as follows:
Key name is "clusterSyncMode" and its values are either "scheduler" or
"none".(both are without quotes and case-sensitive)
Default value is "scheduler", this means it prevents 2
messages being generated regardless of 2 server nodes. This is true,
even if you do not add anything in advanced options table.
Also are more information about this parameter of file adapter, what
is the same for jdbc:
#801926 - XI 3.0 File Adapter: Additional Parameters
Regards
SK

Cisco Prime Infra and SMS gateway integration

Hello,
Can anyone point me to right documents or resources to integrate cisco prime infra 2.x with SMS gateway?
Is there any way I can get SMS alerts for critical events in Cisco Prime Infra 2.x?
Any suggestion is highly appreciated.
Regards,
Girish

Not directly.
If you configure PI to email you on alerts, many carriers allow you receive SMS via an email address - i.e. <your_number>@<your_carrier>

BPM polling interval

Hi, does anybody know if there is a way to establish a polling interval for a BPM in XI ? for example, you can configure a polling interval for the file adapter and this enables you to read a certain filesystem directory every n minutes/seconds...
Is there a way to do the same for a BPM ?
This cuestion comes form the fact that there is no way to configure a´polling interval for the RFC adapter.
Does anybody know if this is posible ?

Hello Hans,
You can schedule a BPM..
Now BPM can only be scheduled by sending a dummy message to XI.
Here are some blogs to helo you:
/people/siva.maranani/blog/2005/05/22/schedule-your-bpm
/people/community.user/blog/2006/11/16/step-by-step-realize-your-bpm-scheduling-capability
THanks,
Himadri

Polling interval for Topology Services in Cisco Prime 4.2

Similar Messages

Maybe you are looking for