Poor gaming performance K8N Neo2 Platinum

I recently installed a new video card - BFG 6800 Ultra and the fps during gaming has dropped drastically. I thought the problem might be the video card so I flashed it to a newer bios, this had no effect. Then I swapped in my old video card - 6800 GT and the problem still existed. I also tried turning off Fast Writes and there was no change. I had my CPU overclocked and tried setting everything to default values, but there was no change. I ran Sandra benchmarks and the CPU / Memory is performing as it should. I would like to figure out if the problem is with a bios setting or the motherboard itself. Here are some benchmarks:
FarCry River Demo:
Before 52.9fps
After 28.8fps
3DMark05
Before
3DMark Score   4425 3DMarks
GT1 - Return To Proxycon   19.6 FPS
GT2 - Firefly Forest   12.9 FPS
GT3 - Canyon Flight   21.9 FPS
CPU Score   4681 CPUMarks
CPU Test 1   2.3 FPS
CPU Test 2   4.2 FPS
After
3DMark Score   2543 3DMarks
GT1 - Return To Proxycon   14.1 FPS
GT2 - Firefly Forest   6.2 FPS
GT3 - Canyon Flight   12.0 FPS
CPU Score   791 CPUMarks
CPU Test 1   0.5 FPS
CPU Test 2   0.6 FPS
Here are my system specs:
MSI K8N Neo2 Platinum 1.4 bios
Athlon 64 3000+
BFG GeForce 6800 Ultra 71.25 drivers
WD 37GB Raptor SATA
WD 160GB SATA
512 x 2 OCZ Platinum Rev. 2 PC3200
Koolance EXOS watercooling (video, CPU)
OCZ Powerstream 520W power supply

Quote from: s4eric on 17-February-05, 02:07:01
I didn't reinstall Windows, but restored to an earlier image. Everything is back to normal.
Crap....I was going to say it was certianly broke and send it to me  ;-)
Glad you got it fixed.
BTW-Why did you go from 6800 GT to an ultra??? So much money sittin' around? I feel your pain.

Similar Messages

  • K8N Neo2 Platinum Ordered - Advice for a noob please

    Hi there,
                this seems like a great forum, was hoping someone could give me some advice - Im trying to pre-empt any major probs....
                I am a relative noob to building P.C's - done a few P4 based systems before but this will be my first Athlon based.  This systems primary use will be gaming.  I have the following on order (should be with me next week) : -
    a) MSI K8N NEO2 Platinum Edition SCK 939 Motherboad
    b) AMD ATHLON 64 3500+ 64bit SCK 939 Retail Inc Fan
    c) 160GB Maxtor Calypso 8mb Cache 7200 SATA DHH
    Components I have already
    a) Graphics Card - Nvidia 6800 GT
    b) Memory - Generic 2 X 512MB PC2700 DDR333 RAM
    c) Sound Card - Creative SB Live Value
    d) PSU - Jeantech 450W (22a on 12V Rail)
    e) Case - pretty generic full tower case - no fans attached
    f) CPU FAN - COOLERMASTER HYPER 48 SUPER SILENT HEATPIPE
    g) Spare Hard drive - 120GB Maxtor IDE Hard drive
    h) DVD Drives - 1 x Pioneeer 108 / 1 x Pioneer 104
    I) Monitors - Ilyama 17" TFT & Toshiba 32WL36P LCD
    I have some 'noobish' questions - apologies for my ignorance : -
    1) Memory - Will my memory be okay ?  Should I ditch it and buy some Corsair DDR400 (which everyone else seems to have!).  Will performance suffer if I stick with the DDR 333 ? Do I need to adjust settings in BIOS regarding memory timing ? (I only picked up on this from reading through other posts on this board, and am totally clueless on 'timing'- Ive never needed to adjust timing on any previous PC's....!)
    2) Sound Card - will I be better off sticking with the onboard sound on the MSI K8N neo 2 ? Or for best performance do I go with the SB LIve ? (god its a nightmare trying to get updated drivers for this card),  Would I get a noticable performance increase buying an Audigy 2?
    3) Vcore / other power issues - Reading this forum Im kinda scared by many posts along the lines of "..for stability I need to change my memory voltage to xx-V" or "...for a stable system I needed to change my Vcore to xx-V".  Will I need to change the Bios default values on this system just to get it to run stably??
    4) CPU FAN - Are AMD stock fans any good ?  My Hyper 48 is quite highly rated....
    5) Im completely new to SATA drives, but Ive printed off the very useful install guide on this site (which I intend to use).  Is there anything I need to look out for concerning adding my IDE drive also.
    I think thats about it just now - if anyone can see any other potential problems with my specs then please let me know.  Im really not trying to be negative / pessimistic - after all the reason I have went for this motherboard is that it is rated as one of the best.  Im just a bit paranoid that the dreaded B.S.O.D awaits me!
    On a more positive note - does anyone have similar system specs they use for gaming ?  How well does HL2 / Doom3 / Farcry etc fly J ? I cant wait !
    Thanks for the time

    you may find these helpful
    Overclockers Uk Power Supplies
    This Week Only Enermax Noisetaker 485W EG495AX-VE(G) SFMA ATX2.0 PSU (CA-007-EN) Might be tempting
    Scan International Power Supply

  • K8N NEO2 Platinum rebooting

    Hi all,just got myself a 64bit MSI K8N NEO2 Platinum board & a 3200+,am happy with it but a couple of days ago i got a blue screen with a long message that i didnt have time to read before the pc rebooted,after the reboot i checked the event viewer log file in administrative tools/control panel but couldnt narrow it down as my particular error code wasnt among the possible causes.
    Among some of the possible causes were incorrectly installed USB drivers or the BIOS,i downloaded the latest BIOS update before this problem started(V1.40) which i am using now,i used the MSI live update software to flash it which i did in windows mode.Sorry for prattling on!well it did it again tonight and i managed to read a bit of the writing on the blue screen which mentioned flashing the bios to the latest version.I was wondering if anyone else is having the same problem and if so could you please advise me? Thanks for your patience and any help Heres my sys specs:
        Model:                         AMD Athlon(tm) 64 Processor 3200+
        Speed:                         2.01GHz
        Model Number:                  3200 (estimated)
        Performance Rating:            PR3015 (estimated)
        Type:                          Standard
        L2 On-board Cache:             512kB ECC Synchronous Write-Back (16-way, 64
                                       byte line size)
        Bus(es):                       ISA AGP PCI USB FireWire/1394
        MP Support:                    1 CPU(s)
        MP APIC:                       No
        System BIOS:                   Phoenix Technologies, LTD 6.00 PG
        Mainboard:                     MS-7025
        Total Memory:                  1023MB DDR-SDRAM
        Model:                         Micro-Star International Co Ltd (MSI) ???
                                       (00E1)
        Front Side Bus Speed:          1x 201MHz (201MHz data rate)
        Model:                         Advanced Micro Devices (AMD) Athlon 64 /
                                       Opteron HyperTransport Technology
                                       Configuration
        Front Side Bus Speed:          1x 201MHz (201MHz data rate)
        Total Memory:                  2048MB DDR-SDRAM
        Memory Bus Speed:              2x 201MHz (402MHz data rate)
        Monitor/Panel:                 CTX EX950F series
        Adapter:                       RADEON X800 Series  
        Adapter:                       RADEON X800 Series Secondary
        Removable Drive:               Floppy disk drive
        Hard Disk:                     Maxtor 6Y080L0
        CD-ROM/DVD:                    HL-DT-ST DVDRAM GSA-4081B (CD 32X Rd, 24X Wr)
                                       (DVD 4X Rd, 3X Wr)
        CD-ROM/DVD:                    MSI CD-RW CR52 (CD 40X Rd, 52X Wr)
        CD-ROM/DVD:                    AXV CD/DVD-ROM SCSI CdRom Device (CD 32X Rd)
                                       (DVD 4X Rd)
        1.44MB 3.5" (A:):              N/A
        Hard drive (C:):               76.3GB (51.9GB, 68% Free) (NTFS)
        CD-ROM/DVD (D:):               N/A
        CD-ROM/DVD (E:):               N/A
        CD-ROM/DVD (F:):               N/A
        Serial/Parallel Port(s):       1 COM / 1 LPT
        USB Controller/Hub:            Standard OpenHCD USB Host Controller
        USB Controller/Hub:            Standard OpenHCD USB Host Controller
        USB Controller/Hub:            Standard Enhanced PCI to USB Host Controller
        USB Controller/Hub:            USB Root Hub
        USB Controller/Hub:            USB Root Hub
        USB Controller/Hub:            USB Root Hub
        FireWire/1394 Controller/Hub:  VIA OHCI Compliant IEEE 1394 Host Controller
        Keyboard:                      Standard 101/102-Key or Microsoft Natural PS/
                                       2 Keyboard
        Mouse:                         PS/2 Compatible Mouse
        Device:                        Creative SB Live! series
        Device:                        Creative Game Port
        Model:                         EPSON Stylus CX3200
        Windows System:                Microsoft Windows XP/2002 Home (Win32 x86)
                                       5.01.2600 (Service Pack 2)
        Network Drivers Enabled:       Yes
        Warning 100:                   Large memory sizes should be made of
                                       Registered/Buffered memory.
        Tip 101:                       Large memory sizes should be made of ECC/
                                       Parity memory.
    >
    >
        Device Type:                   VGA Video Adapter
        Device ID:                     bus 1, device 0, function 0
        Windows Device Name:           RADEON X800 Series  
        OEM Device Name:               ATI Technologies ??? (4A49)
        OEM Hardware ID:               FUN_0, VEN_1002, DEV_4A49, REV_00
        Device Name:                   PC Partner Ltd ??? (4A49)
        Product ID:                    VEN_174B, DEV_0D42
        Revision:                      A / 1 (0)
        Version:                       3.00
        Command Queue Length:          256
        Fast-Writes Support:           Yes
        Over 4GB Addressing Support:   No
        Isochronous Mode Support:      No
        Addressing Support:            32-bit
        Data Transfer Modes Support:   4x 8x

    My K8N Neo Platinum [754] did not include a NB fan. But this usually means the overall size of the heatsink is larger. If you remove the fan from yours, the size of the heatsink will not be big enough to cool your NB. As for temps, I've never seen my NB get hotter than 45'C. Note that the core on my NB should be slightly different than yours.
    You could try to use the BIOS fan control for the NB. If set correctly, it should reduce some noise.

  • Need help with k8n neo2 platinum

    I've just installed a new k8n neo2 platinum s939 board with a venice core 3200+ cpu the htt is 2000 and multiplier 10x.
    I've gone to the core cell menu and set the htt to 4x (seemed to be this at default) and the max mem clock at 166 (more about this in a moment), the fsb will go quite easily up to 250mhz even 255mhz, but when I try 260 Mhz the machine when it reboots shows the initial slash screen but then goes to a blank screen with the cursor flashing in the top left hand corner, I can't even get back into the bios setup without clearing the cmos.
    The odd thing is that the adjust cpu vid is showing a voltage of 1.50 and not 1.40 or startup.
    Anyway with the fsb at 250mhz the bios screen is showing the Current ddr clock at 208 mhz ( not the max memclock setting of 166) the memory in the motherboard ( a crucial 512meg ddr333 single stick) seems to perform OK according to memtest which shows no errors after 2 cycles.
    Any attempt to get to 260mhz fsb appears to fail even by upping the cpu vid to 1.525v unless i adjust the cpu voltage setting which by default is set to (by cpu vid) to +3.3%. Doing this enables me to get to fsb 260mhz but the memtest fails ( even when I set the max memclock to 133, which shows my current ddr speed at 174mhz, well below the 208mhz which appeared stable with the fsb at 250mhz?)
    So firstly why are there two cpu voltage settings in the bios when my manual only shows 1 (there is no mention of this cpu vid setting?
    How is it that my memory is stable at 208mhz with a fsb of 255mhz but unstable at 174mhz with the fsb set at 260mhz?
    Why does the memory clock lock not appear to be working, the memory should be fixed at 166mhz but infact increases with fsb?
    I have bios revision 1.5.
    Please help as I am not familiar with the bios settings for this nforce 3 chipset, they seem rather odd to me. I'm sure my venice core 3200+ cpu can get beyond 250mhz fsb, I have another pc with a venice core 3000+ cpu which runs quite happily at 270mhz fsb.
    PS I've tried reducing the htt to 3x but the same thing happens.

    OK further feed back, I can get to over 260mhz fsb but the system is not stable the memory runs OK with mem test but I have problems with prime95.
    I had to up the cpu core voltage to 1.53v to get to 260mhz using the cpu voltage setting in the bios and setting a 5% increase. increasing the cpu vid setting to 1.55v did not seem to do anything at all the core voltage was still at 1.43v.
    I upped the mem voltage to 2.6v from 2.5 but still could not get the system to be stable, it may be that the memory is holding the system back but I don't want to pay for better memory at the moment. Unless anyone has got any other ideas it looks like I may be forced to settle with 250mhz, well still a 500mhz increase maybe not that bad. I've now to try 3d benchmarking using my radeon 9600xt and 3dmark 03.

  • SATA HDD installation on K8N Neo2 Platinum, Non-RAID, Non-Bootable

    Hi-
    I’m a rank newbie on this forum (first post). I have a K8N Neo2 Platinum Mobo, which I’ve recently gotten up and running, with Windows XP-Pro SP2 installed on a single IDE drive. I would now like to add 2 SATA drives. I don’t need or want the SATA drives to operate in a RAID array, nor do I want them to be bootable. I want to use them independently for data storage. I read the following thread (I am posting here on a separate thread per the author’s wishes not to get his original thread too junked-up) :
    Single SATA or Multiple Drive Array Setup FAQ
    I have not yet plugged-in either of my SATA drives, because I don’t want to risk corrupting my existing boot (IDE) drive. I just had a few questions about the procedure given in the referenced thread, in the Single Drive Setup:
    - Step 14 States: “Make sure the “RAID Mode” is Stripping and Striping Block at 64k or Optimal. Hit F7 (Finish)”. Is this correct for a single non-boot drive?
    - Step 22 States: “As most of you know when you enter the Setup for Win2k/WinXP you will need to hit F6 to load additional drivers for other SCSI devices.” I assume this means I need to boot from the Windows CD. Is this true even if I already have Windows installed on an IDE HDD on this system? At what point will I need to hit <F6> ? Will I be prompted to do so?
    - I have downloaded (from the MSI website) the NVIDIA RAID CLASS DRIVER & NVIDIA Nforce Storage Controller (20 files, 1.3 MB total). Should I put these on a floppy? Or can I access them from a directory on my OS HDD?
    - Should I go ahead and plug-in both of the 2 SATA drives I want to add to the system before beginning the driver installation? The only reason I would consider installing them one at a time is if it eliminated any confusion between RAID vs. independent (I want independent operation). If I do install them one at a time, do I have to install the driver twice?
    Any help would be appreciated.
    - the bbdude

    OK Thanks JeanGuy and ssjkakaroto,
    I have connected both of my SATA drives. They are enabled in BIOS but not set to RAID. I booted up to Windows on my IDE drive. In Disk Manager, the display shows Disk 0 (C: System), Disk 1 and Disk 2 as uninitialized, and my DVD (D:) drive. At this point, I could probably go ahead and run the Initialize and Convert Disk Wizard to get these disks formatted and be dome with ot now. Before I do that though, I just have a couple of more questions.
    - I had already loaded the nVidia nForce3 system driver prior to installing the SATA drives, but I went ahead and did that again after installing the SATA drives and restarting Windows. I used Live Update, which went out to the MSI site and found version 5.03 of the  nVidia nForce3 system driver. I'm not sure how to find the "Nvidia 5.10 driver package which include the latest SATA driver", ssjkakaroto referred-to. The Live Update install procedure did ask if I wanted to install IDE driver and I said yes. It then asked to over-write what I already had there (I said yes to that too). As the file names streamed-by, I though I saw some filenames with nv... listed. So, bottom line, is I'm not sure if I have the lates and greatest nVidia SATA drivers installed. How can I find out what drivers are installed?
    - As I mentioned in my previous post, I have also downloaded and unzipped the NVIDIA RAID CLASS DRIVER & NVIDIA Nforce Storage Controller (20 files, 1.3 MB total) from the MSI site; however, I don't know how to "install" this now that I have the files. There are a couple of .exe and a .bat file (bit no setup.exe).
    I may already have everything I need to partition and format these drives. I just want to bve sure I'm not skipping a step that is essential to optimal performance.
    Thanks -
    - bbdude

  • K8N Neo2 Platinum - satisfied except cold boot

    My new build is doing well except for the near-famous cold-boot problem. When the box has been off for a while, I hit the power button, fans & drives spin up, the optical blinks a couple times, but no video or POST. The LEDs look like 4 green, but 2 seem dimmer, as if they're just reflecting the light from the other 2. A 5-second hiit on the power button shuts it down, hit it again and it fires right up, but stops during post with the message that it's in safe mode and to reset my (nonexistent) OCs. From this point I can F1, boot up, and run for hours. No probs unless it's off for a while. I have seen the problem since early in the build, when I powered up outside the case with just 1 stick of RAM and the LEDs (no vid or drives).
    Searching the board shows a lot of people having the problem, but nobody seems to have a solution, so I went to the support site to check the knowledge-base and FAQs. Interesting to find there that A64 boards do not appear to exist. No FAQ, no option to spec socket 939 or 754 to search the KB.
    Maybe if we get a number of us with the problem to post specs & observations in one thread we can spot a pattern?
    I have noted that I can't just do an on-off-on. It has to spend 20-30 seconds in the lockup mode before cycling the power results in a successful boot.
    BTW all, some really nice things are happening with RAM prices lately. I got my 2 gigs for US$190 delivered.
    K8N Neo2 Platinum
    Athlon64 3500 (130 nm)
    2G (4 x 512) SuperTalent PC3200 RAM
    2 120G Maxtor SATA (1 & 2) in raid0
    1 160G Seagate SATA (3)
    1 Sony DRU 720A 16X dual-layer DVD +/- R/RW (primary master)
    PNY Verto nVidia 6800 vid
    Mad Dog 600W PSU (30A on +12)

    Quote from: elliott on 13-April-05, 09:23:05
    I'll give the bios a shot, but the idea of using the HT to slow the box down and then speeding it back up again in Winders...
    Putting HT to 4 does not slow down the box... Especially if ur FSB is over 200 (if ur overclocking) like in my case: FSB=260mhz, I must put down the HT to 4 in order to run everything perfect. HT standard is 200x5=1000, in my case its 260x4=1040... as long as HT is between 800-1200... I believe there is no real time performance loss as long as u have STABILITY. I have seen a lotta people in this forum fixing stability problems just by reducing the HT when they overclocking... some cases even to HT=3.

  • Os/2 or beos on k8n neo2 platinum

     
    i want to run beos on my system
    or os/2
    i have the k8n neo2 platinum
    athlon 64 3500
    1 gig geil ram
    80 GB maxtor Pata hard drive
    30 gb seagate Pata hard drive
    60 gb SATA maxtor
    ati card (wel figure that one out later)
    BeOS 5 pro just reboots
    and for some ungodly reason i cannot write my os/2 image files without some crap about "BAD TRACK 0" and i just bought a new pack of floppies. and it tells me this with EVERY disk
    the only OTHER OS i can get to run is linux
    which im quite fond of... "anything except WINDOZE"
    I guess what my question is .....WHAT KIND OF VOODOO RITUAL DO I HAFTA PERFORM TO MAKE THIS WORK!!!!!!!
    I dont have any chickens to bleed, but the neighbor does!!!!
    Please help
    ANY help would be GREATLY APPRICIATED!!!!!!!!!!!!!!!!!

    Hi,
    I tried to do the same with os/2 and MSI Neo4 Platinum/SLI and Athlon FX55.
    OS/2 Warp 4 requires 256MB ram or less installed to do initial install.   The first partition of HDD must be less than 2.06Gigs in order for the Kernel to compile.
    EComStation has the newest version of OS/2.  A Google search should take you right to Sundial's site.

  • MSI K8N Neo2 Platinum, Socket 939, nVIDIA nForce3 Ultra Chipset w/ 8X AGP (ATX)

    MSI K8N Neo2 Platinum, Socket 939, nVIDIA® nForce3 Ultra Chipset w/ 8X AGP (ATX)
    and a 3500 90 nm amd 64.........is this a god combo ......Im swicthing mine for this(just the cpu and mobo)  opions?..........any help is welcome...Its in the name of gamging...

    Quote from: duffyone on 31-March-05, 11:54:15
    Now... don't LOL, but there is a reason I picked the 3200+ instead of the 3000+, but I can't remember why???
    Probably because the 3000+ only has a 9x maximum multiplier, whereas the 3200+ will go to 10x.
    2600MHz at 9x means a FSB of 289MHz and ram at 289MHz for best performance.  Will your ram do 289MHz?  Of course you *can* run your memory and fsb async, but I prefer not to.
    Chip

  • Desperate: K8N Neo2 Platinum won't work!!

    Bought myself a new motherboard, processor and memory and it just won't work!
    Searched this forum for a solution, but  haven't found one yet.
    Try to install Windows XP, but it just won't start.
    I now get an error code 0x80040507.
    Before that, it just rebooted again and again.
    My configuration:
    MSI K8N Neo2 Platinum
    AMD Athlon 64 3500+ Winchester core
    2x512 Corsair Twinx1024-3200
    Prim. master: HDD 40 Gb Seagate U100/72 ATA
    Prim. slave   : DVD-RW NEC ND-3500
    Sec. master  : HDD 160 Gb Maxtor Diamond Max Plus 9  ATA
    Sec. slave    : DVD-R from LG
    PSU: Antec 350W, model SL350P (+5V=35A, +12V=16A, +3,3V=28A, -5V=0,5A, -12V=0,8A, +5V=2.0A)
    Sapphire 9800 Atlantis Pro 128Mb
    PCI-1 : empty
    PCI-2 : Hauppauge WinTV PVR250
    PCI-3 : Linksys wireless network card (model WMP11)
    PCI-4 : Creative Soundcard SB Live 1024
    Do I need a new PSU?? or is there another problem?

    AMD recommends a PSU with atleast 24a on the 12v rail. This does not mean your PSU won't hack it, it just means that as a rule of thumb, it's not supposed to.
    Could your PSU be the cause of your problem? Possibly! You have a lot of components drawing power from your PSU. It would be wise to buy a beefier PSU with 12v/5v/3.3v amps all in the 32+ range (see my PSU in my signature or the enermax 460/465w whisper II)).
    The problem with not having a better PSU to work with is you could encounter an error, deem it as a result of something it's not, and think the PSU is good and something is bad when it's really the other way around. Moral to the story: get a new PSU.
    I tried searching microsoft's knowledge base for your error and nothing turned up that had anything to do with windows installation errors. Are you sure you copied the error down correctly?
    If so, the only recommendation I have for you is this. Try installing windows with minimal components installed (CPU, motherboard, videocard, single cdrom, single hard drive). Leave your SB Live! out. Leave your WinTV out. Leave your linksys card out. Leave your DVD-R from LG out. And if you are willing to conserve even more power. If you really want to conserve power, you can install windows with only one stick of ram installed.
    Next thing you want to do is check to make sure the memory is not faulty. Start by putting only one stick of memory in slot one and testing it using memtest86+ (i hope that link is correct). You're going to want to run a 1-4 hour standard loop of tests followed by a 12-24 hour loop of test 5. Then you will do the same thing with stick two in slot one. After this works, test to make sure there's nothing wrong with the motherboard by doing the exact same tests again one by one with the sticks in slot two this time around. After this is all done, do the tests again with both sticks in slots one and two. if it doesn't work like this, you could have faulty memory (but this should work). You can always run your memory in the same colored slots (single channel (slots one and three)) but this will cause you to take a hit in performance. Generally, for all instensive purposes, you should be able to run it in dual channel mode without any problems. I imagine you will be able to if the sticks are good.
    If they don't work in dual channel mode, to be completely honest, I don't know what you would consider the problem then... could be the PSU... could be a badly matched pair... could be the motherboard. All this is determined by how you handled the parts when installing them. There are a lot of unknowns when trying to help a user without knowing anything about their install.
    If all memtests' run successfully, you are now ready to install windows. If windows doesn't install correctly, you probably have a botched BIOS setting somewhere (like aggressive memory timings) or something similiar that's stopping you from successfully installing windows.
    Buy a new PSU  

  • ATI 9000 and K8N Neo2 Platinum

    Hello, I have a K8N Neo2 Platinum motherboard, 1gig (2x 512mb) Dual PC4000 Crucial Ballistix memory, AMD 64bit 3000+ Winchester and a ATI Radeon 9000 pro 128mb.  I am waiting on my X800 XT PE 256 arriving, but in the mean time i am having some trouble running Counter-Strike on this set up, my old system with same graphics card could run CS with 100fps no problem, but now it drops to around 30fps in a heavy gun fight, I have dropped all open gl and D3D setting to performance, messed around with the bios setting's but nothing help's, also I have tried many different ATI driver versions but nothing help, if anyone has had the same problems or can offer any possible causes solutions I would be very gratefull. Oh I have a OCZ 520W PSU

    Leon28,
    The Radeon should perform at least as well as it did on your old comp. Are you using the same version of the Catalyst Drivers you used in your old comp?
    You can get the latest  ATi Drivers to see if it makes a difference.
    Take Care,
    Richard

  • MSI K8N Neo2 Platinum & Adata bh5

    Is there anyone who knows if i will have compatibility problems if i use two 512mb Adata bh5 memory modules with MSI K8N Neo2 Platinum?

    Quote from: duffyone on 31-March-05, 11:54:15
    Now... don't LOL, but there is a reason I picked the 3200+ instead of the 3000+, but I can't remember why???
    Probably because the 3000+ only has a 9x maximum multiplier, whereas the 3200+ will go to 10x.
    2600MHz at 9x means a FSB of 289MHz and ram at 289MHz for best performance.  Will your ram do 289MHz?  Of course you *can* run your memory and fsb async, but I prefer not to.
    Chip

  • Is this RAM ok for a K8N NEO2 Platinum

    I am currently building a system and have got my FX-53 and K8N NEO2 Platinum but i have hit a problem in that i dont know what memory to get for it i have been looking at this http://www.komplett.co.uk/k/ki.asp?sku=116120&cks=PRL
    or if this is no good could some one recommned me one perhaps from this list
    http://www.komplett.co.uk/k/kl.asp?bn=10529

    If you know very little about memory, then what it IS telling you, you won't understand. Here's a tip....on the offset, don't spend a lot of money on memory just yet. Purchase some PC3200, like Kingston KVR RAM or Kingmax...something relatively inexpensive...until you begin to understand timings and voltage adjustments. You will not have any problems with this type of memory, and usually...initial boot-up goes very smoothly.
    Then, after you start to play with timings and such...when you begin to feel comfortable with making these adjustments, and you know your system is stable....then you could experiment with higher-performance RAM.
    That's just how I do it..as I am conservative when first assembling a computer!
    Tim186...."Welcome" to the MSI Forum. Also, check out RexB's 939 build thread...you will find good information in that!!!!

  • Slow RX53, K8N Neo2 Platinum system

    I put together my FX53 system last night. It is replacing a 1 year old P4 3.2 (Oc'd to 3.4) system. Basically I just replaced the CPU and MOBO and everything else is the same. Here are My specs.
    Athlon FX53 939 pin
    MSI K8N Neo2 Platinum
    512 X2 Mushkin Level 2 DDR3500
    EVGA GeForce 6800 GT (in the queue to upgrade to an Ultra)
    SB Audigy ZS
    2X Hitachi Deskstar 200GB RAID 0
    PC Power and Cooling 510 watt PSU
    CD burner DVD burner etc.
    The installation and setup went perfectly. I have my RAM in slots 1&2 and it is reported as Dual Channel 200mhz. I did a fresh install of Windows XP sp2 and installed the latest (5.10) Nvidia chipset drivers and video drivers. My BIOS is basically set to "optimized defaults" (cool-n-quiet and the hardware devices I don't use are disabled). I just wanted to do some testing with untweaked settings to see just how much faster this system is than my old one. Much to my suprise it is slower, not a lot slower, but slower. I'm sure it should be faster. I lost about 6-8 FPS in Doom 3, and 3DMark 2003 lost about 800 points.
    My Sandra scores are
    Memory 5829
    CPU 11067
    Multimedia 22975/24465
    3D Mark 03 is 11,421
    CPU-1059
    As far as I can tell my CPU/Memory benches look ok but not outstanding for my system.  When you throw my Video card into the mix though my performance is less than expected.  I'm stumped and disappointed.  I feel like I  payed almost $1000 for a downgrade.

    512 X2 Mushkin Level 2 DDR3500
    I had the same ram and both my co and cg HATED it.   I ended up replacing it with 2x512 pc4k crucial ballistix.    My A64's love my ballistix.    245 1T 2.5/2/2/6 2.8v or 265 2T 3,3,3,8 2.8v.  
    I personaly do not use memtest for testing A64's.  It been my experience that memtest will miss errors which are detected by Goldmemory.  
    Try setting 2,3,2,7 and bump vdram to 2.8-2.85-2.9v.   The level two has winbond BH-5 chips and they crave voltage.  
    Below is Mushkin's take on the a64's mem controller.
    http://www.mushkin.com/epages/Mushkin.storefront/4156cad701e46ffc2741c0a801020673/UserTemplate/27
    Quote
    Athlon64 3000+ and Higher
    The Athlon64 itself uses a single memory channel and only one controller on the CPU. Because of this, the Athlon 64 (non-FX) can actually use plain vanilla, unbuffered, non-ECC modules. There are, however, still some peculiarities of the Athlon64 systems in how they are handling memory which effects memory compatibility.
    One of the most critical issues in this resepect relates to the first step in the memory access sequence, that is, the opening of a memory page and subsequent steps until a read command can be issued. All of these steps fall into the time frame referred to as RAS-to-CAS delay or tRCD. In a typical system, the memory controller on the chipset is running at bus speed. On the Athlon64, it is running at CPU speed, which means that it is A LOT faster. That means that the internal sequence of commands also goes faster, and that's where all systems are getting hiccups if the memory chips used can only run at a high tRCD.
    A very trivial explanation is that the controller expects that the memory is as fast as it itself but we don't have memory yet running at a 2 GHz and beyond clock rate. What it comes down to is that, depending on the BIOS tuning (by the manufacturer), the read command is issued a bit too early and violates the tRCD. The workaround is to add one additional cycle to the actual memory latency, that is, a 2:2:2-rated DIMM will run stable at 2:3:2; a 2:3:2 rated module will, most likely, need to be set to 2:4:2 in order to run stable (where the latencies are CAS:tRCD:tRP). Bottom line is that when shopping for memory for the Athlon64, it is highly advisable and in most cases mandatory to only consider memory with a tRCD of 2 or, to make it simple, memory that is rated at 2:2:2 a the designated speed. Alternatively, registered DIMMs can be used as well without problems, even though they are slightly more expensive and will give lower performance.

  • Few question above the k8n neo2 platinum and raid

    hi
    i have for now intel 3.4ghz and asus p4c800dlux and 4 sata drives :
    2x36giga wd 10000 raptors in raid 0 (connected to the on board promise sata controller)
    2x200giga wd 7200 jd sata that (connected to on bard sata ports)
    i order a athlon fx-55 and k8n neo2 platinum for a oc (a have 2x512 corsiar pc4000pro and hydro cool 200 ) and its look that its going to be problem  
    "SATA ports 1+2 will not maintain a lock and you can and will corrupt hard drives placed on these channels if you raise the HTT above 220mhz."  
    http://www.madshrimps.be/?action=ge...890&articID=228
    so im in a problem, if i wont to do nice oc (and i will) i need to leave sata ports 1 and 2 not connected and buy a sata-pci controller for my 2x200giga , im right ?
    in that case i need to connect the raptors in raid 0 in the sata 3-4 prots (near the agp) but:
    the raid on the noe2 is "NV RAID (Software)" it means that there is no a controller like promise and the cpu need to replace the controller work, so its doing a lower performance.  

    If you had 4 huge drives I would be more sympathetic. To me every board is a compromise, resulting in me having to abandon something I might have done previoulsy. In you case ditch the two 36gb drives, and slum it with the 200gb drives. Remember that "overclocking" is not a right. There will be many users oblivious of the SATA 1/2 overclocking problems running 4 sata drives in RAID without a problem.

  • K8N Neo2 Platinum supports which Athlon CPUs?

    Pardon my ignorance, but I find this confusing:
    Supports up to 3500+, 3800+ Athlon 64 FX 53, or higher CPU
    Does the K8N Neo2 Platinum support Athlon 64 3500+ and 3800+, and NOT the 3700+? Does it support CPUs in the 4000 range? It would be easier to understand if msi just listed each CPU that this board supports.
    This board is well-recommended, but I was actually considering the Athlon 3700+ for price/performance reasons. It's only $20 more than the 3500+, it's supposed to be easy to overclock, and it's way, way cheaper than the 3800+. But if the board doesn't support the 3700, I'll get the 3500.
    Motherboard specs here:
    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=607
    Thanks.

    Quote from: Bob Jones on 29-April-06, 14:59:51
    Pardon my ignorance, but I find this confusing:
    Supports up to 3500+, 3800+ Athlon 64 FX 53, or higher CPU
    that's because that info is released when the mobo is released. future upgrades are done through BIOS, and you will find additional information about added CPU support in the BIOS descriptions on the site.

Maybe you are looking for