Poor internet signal

I often get a poor internet signal for no reason. I have a D-Link (DSL-G604T) router that is connected via an ethernet cable to my iMac. This works perfectly, but it is also connected to my husbands computer via airport and this doesn't always work properly. He is always able to connect to the network, but the signal strength is very inconsistent. The machine he uses is a 17" 1Ghz PowerBook and it's not in the same room as the router, it's in the next room and the connecting door is always open.

Hello. I had not had my airport for 7 weeks after getting a new drive installed, and just the other day did it.... If I may (hoping to not anger Don) add one thing: the interference robustness that don advised clicking is the computer's interference robustness- you also want to do it to the base station (admin utility, configure, then the row of boxes, make airport the blue (checked ) box....then under wireless options near bottom of page, click, and a page drops down...it discusses multi-cast rate,and then you click that interference robustness tab, then the power setting (if not secure cut power back- if you are password protected, blast it). Then click OK,then click UPDATE at bottom.)
(this last one is when the base station gets the instructions you gave it, it will restart,takes two minutes perhaps).
Last night, I wandered my house with my unit, first time since august.... and WOW did my signal power drop when my air conditioner kicked in.... not for long, then it came back to about half while it ran the rest of the cycle...
SO, any radio interference can have an effect: sun spot cycles, hair dryers, microwaves, all the stuff that used to put snow on a TV screen can weaken the signal. Sorry to be a buttinski... Peace C

Similar Messages

  • Wifi to 2nd imac gets poor internet signal

    my airport extreme/time capsule works fine wifi with close computer. however 2nd computer located 60 feet away, frequently does not get an internet connection. it only gets 2 bars on network symbol. is there anyway to boost the signal to this distant computer?

    Hello winni64. Welcome to the Apple Discussions!
    If you are already operating your AirPort Extreme Base Station (AEBS) with the radio power set at 100% (the default), you still have a few options to try to get a better signal to your 2nd computer:
    o Switch the AEBS's radio mode to "802.11n only (2.4 GHz)." Note your computers must be capable of connecting 802.11n networks.
    o It is very possible that you may have some form of Wi-Fi interference in the immediate area that is preventing your 2nd computer from getting a good clean signal. I suggest you perform a simple site survey, using utilities like MacStumbler or iStumbler to determine potential areas of interference, and then, try to either eliminate or significantly reduce them where possible.
    o Invest in a transceiver. Two examples would be: Wi-Fire from hField Technologies, Inc. and Quicky by QuickerTek.

  • Poor internet speed getting slower

    The area i live in has a very poor internet speed however in the last couple of months it has got significantly slower, where web pages arent evening loading and streaming is getting near impossible
    BT call centre suggested leaving it an hour, then a day then a few days and they would 'fix' something. No change ever happens after these calls and leaving the internet unused for days at a time is getting unacceptable

    ADSL line status
    Connection information
    Line state
    Connected
    Connection time
    0 days, 0:11:29
    Downstream
    1,280 Kbps
    Upstream
    448 Kbps
    Line state
    Connected
    Connection time
    0 days, 0:11:29
    Downstream
    1,280 Kbps
    Upstream
    448 Kbps
    ADSL settings
    VPI/VCI
    0/38
    Type
    PPPoA
    Modulation
    ITU-T G.992.1
    Latency type
    Interleaved
    Noise margin (Down/Up)
    8.2 dB / 15.0 dB
    Line attenuation (Down/Up)
    63.0 dB / 31.5 dB
    Output power (Down/Up)
    15.9 dBm / 12.3 dBm
    Loss of Framing (Local)
    0
    Loss of Signal (Local)
    0
    Loss of Power (Local)
    0
    FEC Errors (Down/Up)
    145 / 0
    CRC Errors (Down/Up)
    4 / N/A
    HEC Errors (Down/Up)
    N/A / 0
    Error Seconds (Local)
    4
    Download Speed(mbps) 0.97
    upload speed 0.24
    ping latency ms 0.00

  • Avoided poor internet connection

    Just bought an Android phone and it doesn't connect to my WOW network wifi. Very shortly after saying it is connected, it comes back with the message: "Avoided poor internet connection." I do not have this problem with any of my other wifi connected devices: iPhones, iPad, Dell laptops, TVs, ...

    Do you have smart wifi enabled? It will use OTA data if it detects a weak wifi signal versus cellular service. Turning it off forces the use of wifi, no matter the signal strength.

  • How can I use an Airport Express to join my wireless network and provide an internet signal to my Power Mac g5 via an ethernet cable?

    I have a power mac g5 that does not have a wireless card, and connects to the internet via ethernet cable.
    I want to know how to set up an airport express so that it joins my wireless home network and provides the G5 with an internet signal.
    This via an ethernet cable that is plugged  into the airport express and then into the ethernet port on the g5.
    Please advise as I have configured the airport express in every way possible, the green light is on and when I plug the ethernet cable into the G5 my network cofigurations shows nothing and says that the ethernet cable is not plugged in (It is).
    I get an internet signal if the ethernet cable is plugged directly into my wireless router, so the ethernet port works.
    Please assist. Thanks.

    Two requirements that must be met to do what you want.......
    1) An AirPort Express 802.11n must be used. Check the Model No on the label on the side of the Express. It needs to be A1264. Any other model number will not do what you want.
    2) The Express must be configured to "Join a wireless network" and the option to enable Ethernet Clients must be checked. 
    Open AirPort Utility and click Manual Setup
    Click the Wireless tab below the row of icons
    The box to "Allow Ethernet Clients" must be checked
    Please check to verify that your AirPort Express meets both requirements

  • No Internet signal with 2 Airport express' & Ipod Hifi

    My Airport express connects with a router and gives a wireless signal all over the house. The 2nd airport express (less than 50'ft. away connects to an Ipod Hifi. The 2nd airport blinks yellow and won't allow me to go onto the internet (ie radio streaming) while I am playing my Itunes thru the Ipod hifi successfully. Also, the 1st Airport is a soid green coIor.Why do I lose the internet signal when the Hifi is playing my Itunes library? I thought the 2nd airport just becomes a part of a network which is how it's setup under the Airport Admin. Utility? What am I doing wrong? Thanks for the help...Henry

    my question is if they are set up to extend my network will my devices like iPhone, iPad, iPod all switch to the strongest available wifi? my set up as follows.
    A newer Mac computer will automatically switch to the strongest wireless access point as it roams about the house, but unfortuntely the iOS operating system used in the iPhone, iPad, iPod etc. is not as sophisticated and will usually not switch automatically to another access point.
    You will likely find that you need to power off the iOS device when you move to another area and power it back up to get it to pick up the strongest access point. Or, you would switch off the Wireless on the iOS device and then switch it back on when the device moves to another area.

  • IMac will not load internnet sites despite it having all green lights on the Network Diagnostics screen.  In other words there is a valid internet signal going into the iMac, but the machine will not load sites. Help? iOS 10.9.5

    iMac will not load internet sites, despite having all green lights (strong WiFi signal etc) on the Network Diagnostics screen. in other words there is a strong
    internet wifi signal going into the iMac but the machine does not connect to the internet.  I OS 10.9.5.  Other devices work fine with the same internet signal.

    iOS 10.9.5 does not exist.
    iOS refers to the operating system on iPhones, iPads, and iPod Touch.
    10.9.5 was never a version of a Classic operating system.
    10.9.5 was a version of Mac OS X, and is 13 years newer than Classic.
    Here are reasons for WiFi signal to fail even when they appear to be strong:
    Most common Wifi issues
    Your Mac may be too close to your WiFi router, in which case, it might be better to connect to it via an ethernet cable if it can't be moved.

  • Internet signal booster?  Is there one available?

    Hi,
    I had to relocate my router to a different location to ensure a strong wireless Internet signal for the desktop computers. However, when I go outside, my signal is too weak for my macbook to connect. Can anyone recommend a signal booster I can get to help strengthen my wireless connection for my macbook?
    Thank you!

    What base station do you have right now?
    Some base stations support external antennas, which can be an inexpensive way of increasing range.
    If yours doesn't, then you may be able to get a second base station and setup WDS (Wireless Distribution System) where the second base station acts as a relay back to the main base station (that's connected to the internet). Again, this depends somewhat on the make/model of base station you already have since not all of them support WDS (Apple's do).

  • Poor wifi signal

    My New Macbook air has very poor wifi signal, I have to sit within feet of my router to have a usable connection, I cannot even use it in the next room.
    Does anybody else have this problem, and would purchasing a antenna booster or signal repeater do the job?

    Here are some troubleshooting suggestions:
    OS X Mountain Lion: Solve problems with connecting to the Internet

  • Can I set up a wifi router to receive an internet signal by connecting it to a computer?

    Can I set up a wifi router to recieve an internet signal by connecting it to a computer?
    It seems to me that routers are designed to connect directly to the internet by programming their firmware with connection info.
    I'd like to connect a computer to the internet, then connect a router to that computer.
    Essentially, I want a internet signal that comes through a computer before being made wireless. Is that possible?

    To connect the computer to the Internet you still need some physical component, for example a wireless USB dongle. So if you want to have the Mac connecting to the Internet and then share this connection to other devices using wireless, then you can enable Internet Sharing on the Mac and select to share its Airport (wireless) connection to the other devices (which turns the Mac into a form of access point). Then the other wireless devices can connect to the Mac and use the Mac's Internet connection, which could be a wireless USB dongle or an Ethernet connection to a cable modem.

  • When I try to open Safari, I get NCSW21 and that server can't be found. This happens everytime. I am using AirPort and have a strong internet signal. I have no problem opening Firefox and surfing the web. Only with the Safari page. Can anybody help.

    Can't open Safari. I get "Can't find server". I get NCSW21 in my address bar. I am using AirPort and have a strong internet signal. I have no problem opening Firefox and surfing the web. Need help. Thanks

    Hi Professor66,
    I have a couple of suggestions for you regarding this issue. Here are two links to users who have posted similar questions to yours and have found their answers in the responses to their posts:
    Safari hangs when loading web pages. | Apple Support Communities
    https://discussions.apple.com/thread/3784708
    Safari loading blank pages | Apple Support Communities
    https://discussions.apple.com/thread/3899912
    I would suggest that you first follow the troubleshooting that the OP did in the second link, which is to test in a new user account to see if the behavior is consistent. If it is, you may need to address the issue at a software level by re-installing Safari. More information on this process can be found in the following article:
    OS X Mavericks: Reinstall apps that came with your Mac
    http://support.apple.com/kb/PH14193
    Thanks for coming to the Apple Support Communities!
    Regards,
    Braden

  • New Time Capsule interferring with internet signal

    My previous setup works perfectly.  This previous setup is as follows:
    older 1 TB TC connected to Bell 2Wire modem/router (2701HG-G in bridge mode)
    Ethernet connection to iMac (2014 running Yosemite) works well
    WIFI throughout the rest of the house works perfectly
    When I swap the older TC with my new 2TB TC, the internet signal is no longer available.  Airport utility sees the Time Capsule, but indicates that there is no internet signal (the globe is amber).  The new time capsule is slowly flashing amber.  The Bell 2Wire still indicates it is receiving an internet signal (appropriate lights all green on the 2Wire).  I have rebooted everything multiple times.  IMac Network Assistant unable to assist.
    So in summary, everything works until I connect the new TC.  When I disconnect it and reconnect my older TC, everything returns to normal and I have a functioning network.  How do I fix this so that I can use the new Time Capsule?

    No, you have one modem.. and one router in a network.. although you can fudge and have two routers.. and suffer double NAT as a result.. you cannot whatever you do have two modem.. that is impossible. As soon as you plug a second adsl modem into the phone line the first will stop working and the second can never start.
    There is a half way solution .. if the 2wire offers DMZ, (by default it does but what Bell has done to it.. who knows).. You can double NAT but all packets are passed from modem router to the TC. it is not ideal but can help the worst of the double NAT effect.
    But I think it is simply better to use the TC in bridge..
    There is an alternative however which I use.. see the write up here.
    Re: airport time capsule keeps disconnecting
    This changes the TC from a dumb bridge to actually intelligent handling of the network.. but no routing. It will work well in my experience.
    To get the express going you need to reset it to factory and start over.

  • I just downloaded iCloud on my PC and noticed that fewer than half of my photo stream photos have transferred over to my PC.  Why is this happening and how can I get the remaining photos?  All of my devices are charged and have perfect internet signals.

    I just downloaded iCloud on my PC and noticed that fewer than half of my photo stream photos have transferred over to my PC.  Why is this happening and how can I get the remaining photos?  All of my devices are charged and have perfect internet signals.  Thanks in advance for any tips and insights!

    It's probably happing because photo stream photos only remain in iCloud for 30 days (even though your last 1000 photos will remain on your devices until deleted).  When you enabled photo stream on your PC you would have only received photos from the last 30 days.
    To transfer older photos to your computer, create a shared photo stream that contains them and invite yourself as a subscriber (see http://help.apple.com/icloud/#mmc0cd7e99).

  • No internet signal

    Hi I have just signed up to EE yesterday and I can't get any internet signal while outside on my iPhone 6

    Hi ,
    Have you tried to reset the network settings as below:
    Note: Resetting the network settings will clear all WiFi passwords and refresh device network connections.
    From the home screen, tap Settings.
    Scroll down to, then tap General.
    Scroll down to, then tap Reset.
    Tap Reset Network Settings.
    Tap Reset Network Settings to confirm.
    Note: If a security code is enabled, this will need to be entered between steps 4 and 5.
    Let me know how you get on .

  • AirPort express not recognising internet signal from cable modem

    my airport express is not recognising the internet connection. It is connected directly via a cable modem (which has full strength when connected directly to the PC) and when networked to the PC it shows in airport utility but when configuring it returns an error message saying it is not recognising an internet signal. the unit can't be faulty as I have just replaced this one with a brand new replacement and the problem is the same. Is there a setting i have missed which is not allowing the signal through from the modem ?

    It is always a good idea to perform a complete power recycle of your networking gear whenever you change network hardware. Please check out the following AirPort User Tip for details on how to do so.

Maybe you are looking for

  • Year property for category dimension

    Since year property is the Required Properties for Category Dimensions, if I need to have actual and budget for multiple year, is this mean that I need to create id for every year? Like following: ID                            year actual_2010       

  • Marantz iPod dock not feeding video signal to tv

    I have the Marantz IS201 iPod dock, which works fine for audio, and talks to the tv fine in terms of displaying iPod data on the screen. But when I actually try and play videos or photos, no joy - most I get is the little play arrow at top left of sc

  • Sequence settings for digibeta anamorphic capture?

    I will be capturing from digibeta where the image is 16x9 anamorphic, using an AJA Kona card. What capture settings and sequence settings must I use to properly deal with the anamorphic image? I am renting the editing suite so I do not have access to

  • After update to iOS 5 my iPad-1 can't add new events to Calendar and Contacts

    After update to iOS 5 my iPad-1 (and iPhone 4) lost "+" symbol to add new events to Contacts /stock iOS-5 Contacts app/, and can't edit old contacts -  i can't change user photo, can't add phone number, ect.and thereis no opportunity to add new conta

  • Testing a webservice proxy client.

    Hello, I am new to JEE and JAX-WS. I generated a client from the webservice interface. It automatically created all the java classes for me. I am writing a simple test class with "main method" to call this web service method. I get null pointer excep