Poor performance for my wlan in conference rooms

Hi,
I have real problems in my conference rooms. I have deployed about 25 aps for my building. I have 1242, 1131, 3501 and 1142's. I have a 2 story building. I've used the WCS maps feature to provide me with a coverage area map. I think that the upstairs and downstairs AP's are interfering with each other. It was suggested I put 3 AP's into one conference room, each with it's own a/b or g radio. How do I pinpoint what is causing the problems with connectivity in my conference rooms?
Also, have you tried manually adjusting power levels? I believe once I start with that, I'll have to touch each and every ap, if I start messing with that. Any suggestions?
Thanks

Remeber that when working with wireless we should always do a site survey to determine the current rf the site has, where to locate the access points , how many access points to get and where to install each ap so that the overlap between the aps is not more then 15%.
Also once the APs are installed you can use the wlc options and heck how many rouges aps the wlc aps are seeing since this rouges would affect your aps and auto rrm will not be able to know what channel to use on the aps managed by your wlc so you would need to configure it manully, also you can go to the monitro tab, select the ap by ap to see how each ap sees the signal to another ap managed y the wlc.
For auto rrm to work on the wlc you need that each ap sees atleast 3 more aps with a good signal to be able to set the correct power and channel to use.
Sent from Cisco Technical Support iPhone App

Similar Messages

WAD-Analysis Item-Poor performance for new lines

Hi.
I use WAD7 for entering new records in IP.
According to our business requirements, in analysis item properties I have defined "Number of New Lines in Planning Queries" = 50.
After that I face before extremely poor performance - it takes about 1-2 minutes until the page has loaded (note that it is empty page - only new blank rows).
When I define new lines = 1 performance is very good (2-3 sec).
Does anybody know what could be the problem ?
Thanks.

Hello Andrey,
the number of new lines configured in WAD is completely unknown in the ABAP backend and has no impact on backend performance; in fact, the front end gets information about one 'line' of template cells, this costs nothing.
Checks for characteristic relationships etc. only may have significant costs for cells of the result set, not for new lines.
Whether this problem comes from the ABAP backed or form the Java stack or from the browser rendering can be checked
with an RSTT trace. Is the run time of the trace different between 1 or 50 new lines, were different backend calls recorded?
If not, the problem comes from the Java stack or from the browser rendering. One can check the latter via task manager.
To check (partially) the run time in Java and/or ABAP stack add the parameter &PROFILING=X in the url, cf. note 1048691.
Regards,
Gregor

Poor performance for full screen desktop

Hi,
Full screen desktop ( displayed as Kiosk ) of Linux with gnome ( I believe it's the same for all window managers ) is poor ( even with command as ls you see the delays ).
It happens on the local network. Connection to the application server is SSH.
SGD server - Solaris 10 , Sun Fire 280. Application server is regular modern PC.
Regular windows performance is very good.
Any suggestions ?
Thanks

I think you will find the poor performance is only with GTK applications.
For example, if you go into a large directory of files, and do an ls -aRl, you will notice it is a lot slower with a gnome-terminal than it is with a plain xterm.
I think 4.3 will resolve this performance issue.

Poor performance for the 1st select everyday for AFRU table

Hello everyone, I have performance problems with AFRU table. Every day, the first time I run a "Z" transaction, it takes around 100-120 seconds, but the second time and following it only takes four seconds. What could I do, in order to reduce the first execution time?
This is the select:
SELECT * FROM AFRU WHERE MANDT = :A0 AND CATSBELNR = :A1 AND BUDAT = :A2 AND PERNR = :A3 AND STOKZ <> :A4 AND STZHL = :A5
The execution plan for this select takes index AFRU~ZCA with an acceptable cost of 6.319. Index AFRU~ZCA is a nonunique index with these colums: MANDT + CATSBELNR + BUDAT + PERNR
I'll appreciate any ideas.
Thanks in advance,
Santi.

What database system are you using (ASE, Oracle, etc?).
If ASE, for the general issue of the first exection of a query taking longer, the two most likely reasons would be
a) the table's data has aged out of cache so the query has to do a lot of physical i/o to read the data back into cache
or
b) the query plan for the query has aged out of statement cache and needs to be recompiled.
This query looks pretty simple, so the data cache seems much more likely.
To get a better feel, some morning run the query with
set statistics io on
set statistics time on
then run it again and look for differences in the physical vs logical i/o numbers and compile vs execution times.
You could use a scheduled event (Job Scheduler, cron job) to run the query or some query very like it a little earlier in the day to prime the data cache with the table data.

Help! Poor Performance for BW reporting in WAD

Hi, Gurus:
I have one BW report, if running it in analyzer and can get the result within 10 seconds, however, when running it in WAD, it cost more than 4 minutes even through it has no data, and I'm really confused by this phenomenon, pls help ,thanks in advance!

Hi
Please check this link .
Re: Tips for Frontend performance - Web Reports (WAD).
Hope this helps.
Cheers
Chanda

Poor Performance in ETL SCD Load

Hi gurus,
We are facing some serious performance problems during an UPDATE step, which is part of a SCD type 2 process for Assets (SIL_Vert/SIL_AssetDimension_SCDUpdate). The source system is Siebel CRM. The tools for ETL processing are listed below:
Informatica PowerCenter 9.1.0 HotFix2 0902 357 (R181 D90)
Oracle BI Data Warehouse Administration Console (Dac Build AN 10.1.3.4.1.patch.20120711.0516)
The OOTB mapping for this step is a simple SELECT command - which retrieves historical records from the Dimension to be updated - and the Target table (W_ASSET_D), with no UPDATE Strategy. The session is configured to always perform UPDATEs. We also have set $$UDATE_ALL_HISTORY to "N" in DAC: this way we are only selecting the most recent records from the Dimension history, and the only columns that are effectively updated are the system columns of SCD (EFFECTIVE_FROM_DT, EFFECTIVE_TO_DT, CURRENT_FLG, ...).
The problem is that the UPDATE command is executed individually by Informatica Powercenter, for each record in W_ASSET_D. For a number of 2.486.000 UPDATEs, we had ~2h of processing - a very poor performance for only one ETL step. Our W_ASSET_D has ~150M records today.
Some questions for the above:
- is this an expected average execution duration for this number of records?
- updates record by record are not optimal, this could be easily overcome by a BULK COLLECT/FORALL method. Is there a way to optimize the method used by Informatica or we need to write our own PL-SQL script and run it in DAC?
Thanks in advance,
Guilherme

Hi,
Thank you for posting in Windows Server Forum.
Initially please check the configuration & requirement part for RemoteFX. You can follow below article for further research.
RemoteFX vGPU Setup and Configuration Guide for Windows Server 2012
http://social.technet.microsoft.com/wiki/contents/articles/16652.remotefx-vgpu-setup-and-configuration-guide-for-windows-server-2012.aspx
Hope it helps!
Thanks.
Dharmesh Solanki
TechNet Community Support

Poor Performance over VPN

Hi All,
I have users complaining of poor performance for TCP applications over a site to site VPN.
I would like to know if anyone knows what to look for when trying to see if we need to reduce the MTU on each side of the VPN.
I dont want to reconfigure MTU unless I have to because one of the two sites is the centre of the hub and I will most likely have to configure it for all of the other sites if I configure it for the one.
the VPNs run between 5510 devices running 7.08 and 8.21
thanks very much for any help
Regards
Amanda Lalli-Cafini

I am having an issue with performance since changing our Linked server connection to SQL 2012. The query in 2008R2 ran in 9 seconds and now it takes around 10 minutes. When I trace the query on the 2 servers, the statement is completely different.
CREATE TABLE [dbo].[PS_OCC_ADDRESS_S](
[EMPLID] [varchar](11) NULL,
[ADDRESS_TYPE] [varchar](4) NULL,
[OCC_ADDR_TYP_DESCR] [varchar](30) NULL,
[ADDRESS1] [varchar](55) NULL,
[ADDRESS2] [varchar](55) NULL,
[ADDRESS3] [varchar](55) NULL,
[CITY] [varchar](30) NULL,
[STATE] [varchar](6) NULL,
[POSTAL] [varchar](12) NULL,
[COUNTY] [varchar](30) NULL,
[COUNTRY] [varchar](3) NULL,
[DESCR] [varchar](30) NULL,
[FERPA] [varchar](1) NULL,
[LASTUPDDTTM] [varchar](75) NULL,
[LASTUPDOPRID] [varchar](30) NULL
) ON [PRIMARY]
Statement:
SELECT EmplId, Address1, Address2, Address3, City, State = substring(State,1,2), Zip = substring(Postal,1,10), County, Country
--INTO tmp_Addr
FROM [Sql03].[DWHCRPT].[dbo].[PS_OCC_ADDRESS_S]
WHERE (Address_Type = 'PERM') and (EmplID IN (
SELECT UserID As EmplID FROM Collegium.dbo.Users
UNION
SELECT EmplID As EmplID FROM Emap.dbo.Applications
UNION
SELECT ID As EmplID FROM HS_Program_Application.dbo.Applications
Any suggestions would be appreciated
SELECT UserID As EmplID FROM Collegium.dbo.Users
into #temp1
UNION
SELECT EmplID As EmplID FROM Emap.dbo.Applications
UNION
SELECT ID As EmplID FROM HS_Program_Application.dbo.Applications
....WHERE (Address_Type = 'PERM') and EmplID IN (select * from #temp1)
Still it does not resolve 9 secs over 10 minutes. Good luck.

Poor Performance using Generic Conectivity for ODBC

Hi my friends.
I have a problem usign Generic Conectivity , I need update 500,000 records in MS SQL Server 2005, I'm using Generic Conectivity for ODBC. In my Oracle Database i have create a DB_LINK called TEST to redirect to MS SQL Server database.
Oracle Database: 10.2.0.4
MS SQL Server version: 2005
The time for update 1,000 records in MS SQL Server using DBMS_HS_PASSTHROUGH is ten minutes. This is a poor performance.
This is de PL/SQL
DECLARE
c INTEGER;
nr INTEGER;
CURSOR c_TEST
IS
SELECT "x", "y"
FROM TEST_cab
WHERE ROWNUM <= 1000
ORDER BY "y";
BEGIN
FOR cur IN c_TEST
LOOP
c := DBMS_HS_PASSTHROUGH.OPEN_CURSOR@TEST;
DBMS_HS_PASSTHROUGH.PARSE@TEST(
c,
'UPDATE sf_TEST_sql
SET observation= ?
WHERE department_id = ?
AND employee_id = ? ');
DBMS_HS_PASSTHROUGH.BIND_VARIABLE@TEST (c, 1, 'S');
DBMS_HS_PASSTHROUGH.BIND_VARIABLE@TEST (c, 2, 'N');
DBMS_HS_PASSTHROUGH.BIND_VARIABLE@TEST (c, 3, 'ELABORADO');
DBMS_HS_PASSTHROUGH.BIND_VARIABLE@TEST (c, 4, 'PENDIENTE');
DBMS_HS_PASSTHROUGH.BIND_VARIABLE@TEST (c, 5, cur."x");
DBMS_HS_PASSTHROUGH.BIND_VARIABLE@TEST (c, 6, cur."y");
nr := DBMS_HS_PASSTHROUGH.EXECUTE_NON_QUERY@TEST (c);
DBMS_HS_PASSTHROUGH.CLOSE_CURSOR@TEST (c);
COMMIT;
END LOOP;
END;
You can help, how better the performance for update 500,000 record by record in MS SQL Server. I need advantages of use Oracle Transparent Gateway for Microsoft SQL Server.
your's can suggest my another solution ?
Thanks.

Hi,
There are no real parameters to tune the gateways. You should turn on gateway debug tracing and check the SQL that is being sent to SQL*Server to make sure is update statements and nothing else.
If this is the case then the time taken will be down to various factors, such as network delays, processing on SQL*Server and so on.
How long does it take to update the same number of records directly on SQL*Server without the Oracle or the gateway involved or if you use another non-Oracle client to do the same updates across a network, if a network is involved ?
It may be possible to improve performance by changing the HS_RPC_FETCH_REBLOCKING parameter, so have a look at this note in My Oracle Support -
Tuning Generic Connectivity And Gateways (Doc ID 230543.1)
Regards,
Mike

Block conference room for all but one user

hoping to lock down one conference room I turned off autoprocessing and added user to resource inpolicy
but mtg resources are stil going in the room.

Hi,
If you don’t want other users to send message or meeting request to this room, we can limit the sender for this room mailbox to specific users, for your reference:
We can click Add button to add specific user and save the settings.
Regards,
Winnie Liang
TechNet Community Support

Conference room camera for Connect Pro??

Trying to determine the best voice activated pan/tilt/zoom
camera for conference room to use with Adobe Connect Pro. Any
information is helpful . . . type of camera, quality of picture,
functionality, cost, connection, etc. Thanks!

Please post your Connect Pro questions here:
http://www.connectusers.com/forums/cucbb/
You might be able to find the answer to your question here:
http://www.connectusers.com/community/monthly_topic/2008/12/
We did a topic of the month on video in December

New Project settings...possible solution for AVCHD poor performance

I have experience very poor performance when editing AVCHD content from my Canon camera. I was using the DV widescreen by mistake as the last format I used was a DV camera.
When I switched to AVCHD Full HD 1080i 30 the performance was greatly improved. But I actualy have my camera set for 1080p 30. It's a setting on the canon vixia HF S100. My options are 60i, 30p, or 24p. I prefer no interlacing so I can avoid de-interlace issues when posting content on computers (plus most TVs are progressive today and it's easier to go from p to i without impacting quality).
But which options is best for me? should I try and create my own custom setting? I noticed in the Hard Disk and Flash presets they have two settings (one says 60i but that is anamorphic). The HD 1080i 30 looks like the same settings Full HD 1080i 30.
Thanks in advance.

There is a little easier Way to Navigate in Doing an F.D.R. than that Method: I listed it here if you prefer going this Route..
2. Re: FACTORY RESET FOR RAZR AN RAZR MAXX

1130 AG in a conference room for WiFi media presentation

Does Cisco have a solution to a conference room setting where the presenter can xmit his images (.ppt etc...) from laptop via WPA2/eap-fast AP to a plasma monitor (the monitor will have a VGA input std 15-pin).
Appreciate the help tremendously!

Cisco has an application called Meeting place where the user can exchange the presentation

Crashing and poor performance during playback of a large project.

Hi,
I've been a regular user of iMovie for about 3 years and have edited several 50GB+ projects of DV quality footage without too many major issues with lag or 'dropped frames'. I currently have a 80GB project that resides on a 95% full 320GB Firewire 400 external drive that has been getting very slow to open and near impossible to work with.
Pair the bursting-at-the-seams external drive, with an overburdened 90% full internal drive - the poor performance wasn't to be unexpected. So I bought a 1TB Firewire 400 drive to free up some space on my Mac. My large iTunes library (150GB) was the main culprit and it was quickly moved onto the new drive.
The iMovie project was then moved onto my Mac's movie folder - I figured that the project needs some "room" to work (not that I really understand how Macs use memory) and that having roughly 80GB free with 1.5GB RAM (which is more than used to have) would make everything just that much smoother.
Wrong.
The project opened in roughly the same amount of time - but when I tried to play back the timeline, it plays like rubbish and then after 10-15 secs the Mac goes into 'sleep' mode. The screen goes off, the fans dies down and the 'heartbeat' light goes on. A click of the mouse 'wakes' the Mac only to find that if i try again, I get the same result.
I've probably got so many variables going on here that it's probably hard to suggest what the problem might be but all I could think of was repairing permissions (which I did and none needed it).
Stuck on this. Anyone have any advice?

I understand completely, having worked with a 100 GB project once. I found that getting a movie bloated up to that size was just more difficult with jerky playback.
I do have a couple of suggestions for you.
You may need more than that 80GB free space for this movie. Is there any reason you cannot move it to the 1TB drive? If you have only your iTunes on it, you should have about 800 GB free.
If you still need to have the project on your computer's drive, set your computer to never sleep.
How close to finishing editing are you with this movie? If you are nearly done except for adding audio clips, you can export (share) it as QuickTime Full Quality movie. The resultant quicktime version of your iMovie will be smaller because it will contain only the clips actually used in the movie, not all the saved whole clips that iMovie keeps as its nondestructive editing feature. The quicktime movie will be one continuous clip, incorporating all your edits and added audio. It CAN be further edited, but you cannot change text of titles already there, or change transitions or remove already added audios.
I actually do this with nearly every iMovie. I create my movies by first importing videos, then adding still photos, then editing with titles, effects and transitions. I add audio last, and if it becomes too distorted in playback, I export the movie and then continue adding audio clips.
My 100+ GB movie slimmed down to only 8 GB with this method. (The large size was due to having so many clips. The movie was from VHS footage of my son's little league all-star game, and the video had so many skipped segments that I had to split it into thousands of clips to remove the dropped ones. Very old VHS tape!).
I haven't upgraded to QT 7.5.5, but I heard that the jerky playback issue is mostly resolved with this new upgrade. I am in mid-project with about 5 iMovies, so I will probably plod along with my work-around method, not wanting to upgrade in the middle of any of them.
Hope this is helpful to you.

New Conference Room with A/V + teleconference

My firm is adding floor space which is currently being built out. Two rooms are designated as conference rooms. Now that construction started I have been asked to, immediately, provide specs on designing the rooms for:Webinars -- typically from outside parties over Internet (requires PC)A/V presentation -- typically clients or others making a presentation in our office. Might be using laptopTeleconferencing -- between my firm and other parties.In-house conference/work area -- requires power/data in conference table in center of roomConference rooms are not very large 11.5' x 12.5' & 10.5' x 11.75'.We are looking to avoid wires dragging across floors.We plan on having a wall mounted Flat Panel.I am not familiar with what is available re teleconferencing, A/V connectivity/ typical conference room layout. Any and all suggestions are...
This topic first appeared in the Spiceworks Community

Hi,
Publisher would know about the user, who would be sending the message or asking the question.
So what would happen is, as the user tries to type something in the chat pod/app, the users info is broadcasted across the room. So by the time, the user asks the question, everyone would know about the user. Hope this clarifies and suits your scenario.
Answering the other question by Davis,
Yes even if one of your clients doesnt support p2p (firewall or lower FlashPlayer version), the streams switch back to hub and spoke. And;
P2P doesnt correlate to poor quality, infact it might be better than hub and spoke given the right circumstances. So you should infact see better quality in P2P mode.
Thanks
Arun

Apple maps has received a poor performance rating just after introduction of the iPhone 5. I am running google maps app on the phone. Siri cannot seem to get me to a specific address. Where does the problem lie? Thanks.

Apple maps has received a poor performance rating just after introduction of the iPhone 5. I am running Google Maps app on the phone. SIRI cannot seem to get me to a specific address. Where does the problem lie? Also can anyone tell me the hierarchy of use between the Apple Maps, SIRI, and Google maps when the app is on the phone? How do you choose one over the other as the default map usage? Or better still how do you suppress SIRI from using the Apple maps app when requesting a "go to"?
I have placed an address location into the CONTACTS list and when I ask SIRI to "take me there" it found a TOTALLY different location in the metro area with the same street name. I have included the address, the quadrant, (NE) and the ZIP code into the CONTACTS list. As it turns out, no amount of canceling the trip or relocating the address in the CONTACTS list line would prevent SIRI from taking me to this bogus location. FINALLY I typed in Northeast for NE in the CONTACTS list (NE being the accepted method of defining the USPS location quadrant) , canceled the current map route and it finally found the correct address. This problem would normally not demand such a response from me to have it fixed but the address is one of a hospital in the center of town and this hospital HAS a branch location in a similar part of town (NOT the original address SIRI was trying to take me to). This screw up could be dangerous if not catastrophic to someone who was looking for a hospital location fast and did not know of these two similar locations. After all the whole POINT of directions is not just whimsical pasttime or convenience. In a pinch people need to rely on this function. OR, are my expectations set too high?
How does the iPhone select between one app or the other (Apple Maps or Gppgle Maps) as it relates to SIRI finding and showing a map route?
Why does SIRI return an address that is NOT the correct address nor is the returned location in the requested ZIP code?
Is there a known bug in the CONTACTS list that demands the USPS quadrant ID be spelled out, as opposed to abreviated, to permit SIRI to do its routing?
Thanks for any clarification on these matters.

siri will only use apple maps, this cannot be changed. you could try google voice in the google app.

Poor performance for my wlan in conference rooms

Similar Messages

Maybe you are looking for