Popping sound soundbar when changing channels

I recently purchased a soundbar to go with my HDTV set. Experience popping when changing channels or when changing settings in the DVR. Manufacturer of the soundbar says that I must match the STB (Motorola 7232) audio settings with the TV's which is Force or LPCM and turn off Dolby Digital. However, I cannot find these settings.
Take the soundbar out of the mix and the TV does not experience any popping. This tells me that this cannot be the STB but the manufacturer says it is. Any help with audio on FiOS TV would be greatly appreciated.
Solved!
Go to Solution.

Let us know if you find the menu. The tricky thing is that you have to power it off from the front display and then do ok menu using the remote. It took ne a couple times to get there with the new box. Best of luck.

Similar Messages

  • Hanging when changing channels

    I am currently on release 1.9 build 10.95. Ever since the software was "upgraded" I have noticed the following:
    Intermittently, when changing channels, by selecting from the guide, often the system will hang, for up to a minute, before the channel finally changes, almost as if it is waiting for something to time out.
    Intermittently, when I use the remote, the green light will flash on the box showing that a signal has been received, but nothing happens. I may have to issue the command two or three times.
    This has happened on all three of our DVR's - Motorola QIP - 7216 1
    I have reset the box via software, physically reset the box by pulling the power chord, and put new batteries into the remote, numerous times, and the problem persists.
    Is it only me, or has this problem been reported under a different heading?

    Usually, you can turn off a video setting and it speeds up the responce time of the set top box. Try hitting menu - settings - video settings - sd override and selecting off. There are other settings in there but they dont seem to affect the responce time much.

  • Headphone sound only when changing level or balance

    Hi,
    I have a weird problem with my Logitech B530 USB headset.
    I have configured it as the main input and output device in system settings, but I only hear sounds when changing sound level or balance. So if I e.g. start some music in iTunes I hear nothing, if I then increase/decrease the volume I hear the song, but the sound quickly fades away and there is no sound again. The same thing happens if I change the device balance.
    Has anyone experienced anything similar and/or have any idea how to fix this?
    Thanks,
    Mads

    = Yes it came pre-installed,? it's an x-fi xtreme music, is there any other way to find the exact model? Im pretty sure my card is upside down so It would? be impossible to read the serial number which is on the bottom. It doesn't seem to be a hardware issue at all, it seems to be a software [email protected]

  • When change channels audio stuck in loop

    Starting yesterday when I change channels on the HD FIOS box- the channels change immediately as usual but the last sentence of the channel audio previous channel loops and repeats for about 7-8 seconds. Once it stops, the audio on the new channel is out of sync. If I change channels again- it corrects iteself.  I can usually change about 3-4 more channels and evertything is normal, however it will start up again. This is not a picture problem- just audio as descrived above.
    I have unplugged the HDMI- the cable from the wall to the unit- and uplugged the power to the HD unit yesterday (did not matter) and today (Did not matter).  Could the HD box need to be replaced?  I have an HD DVR downstairs and there is no problem on that system down stairs.
    Thanks

    Not sure if this will help, but did you try going into the DVR customer support menus and selecting the item called Fix Common STB/DVR issues?   This can correct a lot of audio & video issues on a DVR.  You will have to hunt for this menu item since Verizon for some reason keeps moving it around and renaming it every few months.  It will take 5 - 10 minutes to run and will reboot your DVR (perhaps a couple of times).
    I don't recommend pulling the plug on a Verizon DVR since you will likely cause more damage to the DVR hard drive.  The Verizon DVR is always recording your current channel even when it is in screensaver mode.  When you pull the plug, it may cause the recording head on the hard drive to become damaged or damage the recording surface since the drive head is not properly parked when it loses power.  At best you will corrupt the filesystem  on the hard drive.  Try the Fix Common DVR Issues app a couple of times before pulling the plug.   Pulling the plug should be the absolute last resort.

  • Loss of sound effect when changing volume.

    Hi there,
    I have just purchased a Macbook Pro and everything was going well until I noticed that when I changed the volume using the F11 and F12 keys, the sound effect would no longer be produced. I have been through Sounds in System Preferences and checked all the settings are correct, even the 'play feedback when volume is changed' option is checked. All I have been doing so far is using iTunes and using the internet. I also loaded djay but I don't think this would have anything to do with it. Please help.

    iCloud only keeps photo stream photos for 30 days, even though up to 1000 photos will remain on your devices until deleted.  When you re-enabled photo stream you only received photo stream photos from the last 30 days as older photos are no longer in iCloud.
    To change your iCloud ID, go to Settings>iCloud, tap Delete Account, then sign back in with the new ID.  This deletes the account and your iCloud data from your device, but not from iCloud.  Provided you are signing back into the same account, your iCloud data will reappear on your device when you sign back in.
    However, to avoid losing photo stream photos, before deleting the account save them to your camera roll (if not already there).  To do this, open your my photo stream album, tap Edit, tap the photos, tap Share, then tap Save to Camera Roll.  Be sure to do this on your other devices first.
    To get the missing photos back on your iPod, create a shared photo stream that includes them on one of your other devices and invite yourself as a subscriber (see http://help.apple.com/icloud/#mmc0cd7e99).

  • Sound disappears when changing speaker config

    Hello all, I currently have a bit of an annoying issue when using my x-fi titanium card in vista 64 bit.
    When I goto change my speaker config from headphones to 5.1 or vice versa, the sound from the running apps disappears
    and I have to restart the applications for sound to come back. For example I am playing a song in winamp, i change speaker config
    from 5.1 to headphones, sound gone, close winamp and reopen sound is back. Same thing goes for my games.
    Any possible solutions to this thanks.

    The only thing I don't like about the iPhone headset solution is that the earplugs are uncomfortable, and keep falling out. I basically don't like things stuck in my ear. So I am thinking of buying an actual over-the-ears headset to plug in to the headset port.
    A couple of questions:
    - Is there any reason at all to go USB headset instead? It seems like a waste of a USB port since there is a headset jack.
    - Is there any way of switching the output sound back to the speakers while the headset is plugged in? Or do I have to physically unplug it each time it is not in use for a Skype call (which is the only time I would use it)?
    Thanks,
    doug

  • Headphone noise (pop sound) heard when switching to audio.

    Has anyone encountered a popping noise when the start listening to audio (MP3s, starting a call, etc.) through their headphones?  I am wondering whether this may be a design flaw, a setup issue, a hardware problem with my BB Curve 8830 or with the headphones themselves.  I am using the headphones that came with the unit.  I have had this problem from day one and it's really irritating.  Thanks, Dan.

    I have the same problem, actually two different pops.  The first is a loud pop when using any kind of headphone or speaker, right when the music is about to start, almost identical to the old pop when one placed a needle down on a vinyl LP.  (Anyone here young enough to remember those?)
    The second is a softer but clearly audible pop between songs - however - this one is only audible using certain headphones and particularly speakers (like PC speakers).   What is with this?  Surely this is fixable - hello RIM ??
    Any hints appreciated.  My Curve is new, from Verizon, and appears to be using system 4.3.  Will look into updates on that.
    Not to hijack the thread, but perhaps I can toss out my other Media Player problem.  I had trouble downloading with WMP and Roxio so I am using MediaMonkey - I can get songs, album art, and even playlist names but when I check the playlists on the Curve, they are empty.   Anyone run into this?  I have MMS enabled, USB support, etc.    Thanks !

  • Pixels when changing channels

    Received new replacement black box this week, all fine so far (shock horror!), apart from when I flick channels, the pictures pixelate for about 5 seconds, which is quite annoying. The new broadband channels dont do this. Any suggestions? Cheers!

    Hi Ggmcintosh,
    The only time I have experienced the problem you mentioned is on the channel where my reception hasn't been great. You could try Rescanning your channels to see if this makes a difference.
    Thanks
    Paddy
    BTCare Community Mod
    If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
    We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)

  • Display  Pop up message when  changing and displaying sales orders?

    Hi Friends,
    My client requirement is to display text popup during change sales order VA02 , and  Display sales order VA03.
    Pls find me a answer for this , Thanks.
    Nina.T

    Hello Nina...
    Hope you are aware of the configurations you need to maintain for the Text determination.Anyway, herewith are the steps that may help you to accomplish your requirement.
    Text Determination procedure for sales document header:
    Text can be determined at sales document header level or it can be imported from customer master. The process is...
    Define Text types: Path: Imgsales and distributionbasic functionstext controldefine text types
    Select sales document header. click on text types go to new entries and define text types. For Eg:Z1
    Define Access sequence:
    Select sales document header
    Click on change icon
    Click on access sequence control button under dialog structure
    Go to new entries and define access sequence number with description.Ex: 55
    Save it and exit
    Define text determination procedure:
    Go to new entries
    Define text determination procedure.Ex: ZX save it and exit
    Assign text id's to text determination procedure:
    Select your text determination procedure(ZX)
    click on text id's in text procedure control button under dialog structure
    go to new entries and maintain entries. Text id:assign text id (Z1) that we defined in the previous step
    Specify sequence No-10
    Check Reference: this indicator specify that the text is reference or copies from preceding object
    Text in obligatory: text will be displayed during copying. the value of this field specifies whether text is obligatory or not and if it is obligatory the how it is to be displayed
    Apart from this... you also have to maintain the text in the Customer master as mentioned in the previous mail..
    Thanks,
    Safeer Rahman

  • 42TL515U blacks out when changing channels in different formats

    This television is getting annoying. Unlike our previous television, a Samsung, whenever I switch from a program from a non HD channel stored on the DVR to a live HD broadcast the Toshiba frequently seems to "get confused" with the format switch and the screen goes black. Sometimes I have to reboot by turning it off and on and then wait 40 seconds for it to power on and go to the HD station. This was an expensive purchase - at least for our budget - but I am very disappointed. In retrospect, I probably should have bought another Samsung or the Vizio.
    John

    Usually, you can turn off a video setting and it speeds up the responce time of the set top box. Try hitting menu - settings - video settings - sd override and selecting off. There are other settings in there but they dont seem to affect the responce time much.

  • Popping sound when locking iPhone

    Hi, I just got my iPhone replaced by apple for the second time, Everything works fine except for when after I make a call or receive a call and I go to lock my phone, Instead of the normal lock sound I get this popping sound. When I wake my phone up and unlock it, there is no sound even when I lock it again. Only thing I've found that helps is putting the headphones in and out and resetting the phone but when i go to make/receive a call then put the phone to sleep, the popping sound comes back. Is it a defect with the hardware? Since my previous two phones never did this, I don't wanna go back to apple asking for another phone.

    Have you tried basic troubleshooting of the hardware?
    Such as Rebooting iPhone, Restoring iPhone. If this continues after a restore then yes I do advise you visit your apple retail store with appointment or contact iPhone support so they can assist you under the hardware warranty.
    How to verify iPhone hardware is working correctly
    http://support.apple.com/kb/HT1650
    iPhone and iPod touch: Minimum system requirements
    http://support.apple.com/kb/TS1323
    Backing Up, updating, and restoring your iPhone and iPod touch software
    http://support.apple.com/kb/HT1414

  • Airport express popping sound

    I am experiencing random popping sound like when you plug in a guitar into an amp without turning down the amp first. I was wondering if anyone knew the cause of this since i dought that it is good for my speakers.
    I currently have an express that I just got for xmas as well as insignia speakers plugged into them and I am running windows 7 on a hp hdx16 if that helps anyone with my problem

    is there anything else i could do to make sure this popping stops?
    Sorry, none that I can think of. You'll have to decide if drinking beer is more important than steaming iTunes.
    also is it as bad for my speakers as I think it probbly is?
    Unfortunately, yes. Each time you hear that "pop,"the speaker cone is most likely banging against its mechanical stops. Eventually, this will damage the speaker's ability to reproduce audio at its designed full range.

  • P775 -S7320 crackling and popping sound

    I get a crackling/popping sound occasionally when listening to just about anything. It happens when watching online videos and listening to music on Windows media. I can hear it out of both speakers, and when using headphones.
    Any ideas what the problem could be?
    I have updated all drivers.

    I noticed that recently I am having the same problem with a P775-S7236.
    If I reboot the laptop then it goes away but eventually it comes back.
    Did you solve your problem.
    TIA

  • Popping sounds back with Leopard

    The problem with the popping sounds, introduced with 10.4.10 and fixed with audio update 1-2007 is back after upgrading to Leopard. At least on my MacBook. Here ist the old thread regarding this topic. The symptoms are absolutely the same.
    http://discussions.apple.com/thread.jspa?threadID=1005162&start=0&tstart=0

    My new MacBook also makes these popping sounds, usually when no audio is playing, but sometimes during music playback. I hope this is just a software problem and there's nothing wrong with my Mac.
    These little "bugs" (BootCamp problem, PC Server showing up when it should'nt, this popping sound etc.) and stuff keep gnawing up the good image I had of Apple computers (as this MacBook is my first).

  • So in the last few days I've noticed that pressing my volume change keys actually isn't changing the volume on my macbook pro at all. When I press the volume up or down keys, it makes the recognisable pop sound but stays at the same volume while the squar

    So in the last few days I’ve noticed that pressing my volume change keys actually isn’t changing the volume on my macbook pro at all. When I press the volume up or down keys, it makes the recognisable pop sound but stays at the same volume while the squares go up or down. I mute it but my computer still makes sound. It’s the same with the volume control up the top of the screen, too. I slide it up and down and it doesn’t change the volume at all. The only way I can change the volume is with my speakers or the program I’m in (iTunes, VLC etc). I restarted and it seems to be okay then I go to change it a couple minutes later and it’s back to not working again.
    I’ve checked my settings- the “use all F1, F2, etc. keys as standard fuction keys” is not switched on, and I have tried a suggestion of moving the com.apple.systempreferences.plist file out of the library and onto the desktop and restarting and neither of those seem to make any difference whatsoever. I’ve tried to find online forums but the only suggestions I found were those two and they didn’t work.
    I’m just annoyed because I usually have the worst luck with technology but my macbook had been going strong and I got it because of the apparent lack of things that could go wrong, but of course even if there is one thing that could go wrong it will happen to me.
    Please help!

    You migh give resetting your NVRAM a try:
    http://support.apple.com/kb/ht1379

Maybe you are looking for