Port forwarding for Mac that shares internet to Airport in bridge mode?

I use Air Video server, which allows me to stream movies from my Mac to my iPhone or iPad. It sits on port 45631 and that's closed.
I recently moved from NYC to CO, and because of my cable modem not being compatible with my older Airport router, I must use my Mac Pro to forward my Internet service from one Ethernet port to another - so that my older Airport Extreme can then broadcast wirelessly.
Since I use the AirPort in bridge mode, and the Mac is forwarding the connection - how do I forward the port so Air Video can send through to the internet?
thanks for ANY help, I'm a bit lost here

Similar Messages

How do you set up Port Forwarding for ARD 2.2 in AEB N?

Help,
I'm a novice at Apple Remote Desktop (ARD) - not an IT guy, so it has to be pretty basic and detailed.
How do you set up Port Forwarding for ARD 2.2 on the Apple Airport Extreme BS router, 802.11 N. I have one at each end of the internet connection. At one end I have an Airport Extreme N router with 2 macs and eventually 1 windows XP machine (if I can) that I would like to be able to connect to over the interenet (the clients) and at the other end, I have a Mac with ARD 2.2 installed also with an Airport Extreme N router. Note: Both routers use Static IP addresses and all computers use static IP's internally not through DHCP. What are the settings or directions to do this.
I have read and printed out the directions for Configuration of ARD 3.0 that are posted many times in the ARD discusion group, but it uses a Linksys router ( http://www.starkpr.com/ard.htm posted by Dave Sawyer). The Mac router is different, particularly with the place to set a Private IP address. I'm not sure about alot of things, but especially about the Private IP address, what number do I set it to, the one that is in my Network connections list? It automatically changes to a different number in AE N setup for Port Forwarding (by one) as if it is not suppose to the same?????
Are there any directions available that are as straight forward for the Airport Extreme N router, as the one's that are listed here for the Linksys Router's? ( http://www.starkpr.com/ard.htm )
Any and All help will be greatly appreciated.
P.S. I know I should have 3.0 but bought 2.2 just weeks before 3.0 came out and they would not give me an upgrade price, so I'm waiting for 4.0 to upgrade.
Thanks,
Jim

Try the following for each AirPort Extreme ...
AEBSn - Port Mapping Setup
To setup port mapping on an 802.11n AirPort Extreme Base Station (AEBSn), either connect to the AEBSn's wireless network or temporarily connect directly, using an Ethernet cable, to one of the LAN port of the AEBSn, and then use the AirPort Utility, in Manual Setup, to make these settings:
1. Reserve a DHCP-provided IP address for the host device.
Internet > DHCP tab
o On the DHCP tab, click the "+" (Add) button to enter DHCP Reservations.
o Description: <enter the desired description of the host device>
o Reserve address by: MAC Address
o Click Continue.
o MAC Address: <enter the MAC (what Apple calls Ethernet ID if you are using wired or AirPort ID if wireless) hardware address of the host computer>
o IPv4 Address: <enter the desired IP address>
o Click Done.
2. Setup Port Mapping on the AEBSn.
Advanced > Port Mapping tab
o Click the "+" (Add) button
o Service: <choose the appropriate service from the Service pop-up menu>
o Public UDP Port(s): 3283
o Public TCP Port(s): 3283
o Private IP Address: <enter the IP address of the host server>
o Private UDP Port(s): 3283
o Private TCP Port(s): 3283
o Click "Continue"
o Click the "+" (Add) button
o Service: <choose the appropriate service from the Service pop-up menu>
o Public UDP Port(s):
o Public TCP Port(s): 5900
o Private IP Address: <enter the IP address of the host server>
o Private UDP Port(s):
o Private TCP Port(s): 5900
o Click "Continue"
o Click the "+" (Add) button
o Service: <choose the appropriate service from the Service pop-up menu>
o Public UDP Port(s):
o Public TCP Port(s): 5988
o Private IP Address: <enter the IP address of the host server>
o Private UDP Port(s):
o Private TCP Port(s): 5988
o Click "Continue"
(ref: "Well Known" TCP and UDP ports used by Apple software products)

Port forwarding for online gaming...dumb question

Hi, I'm trying to set-up port forwarding for online gaming. There's a section that asks for port numbers, "Enter the starting numbers of the External Ports (the port numbers seen by users on the Internet)" Where do I find the numbers of the ports?

http://portforward.com/cports.htm
If the game isn't listed there, google for it.

Port forwarding for WOW

Hello,
Just a TC today and cant find any info on how to port forward for the TC. Anyone have any clues?

Sorry, I don't have a TC, but the port mapping (forwarding) steps should be the same as for the 802.11n AirPort Extreme Base Station (AEBSn).
AEBSn - Port Mapping Setup
To setup port mapping on an 802.11n AirPort Extreme Base Station (AEBSn), either connect to the AEBSn's wireless network or temporarily connect directly, using an Ethernet cable, to one of the LAN port of the AEBSn, and then use the AirPort Utility, in Manual Setup, to make these settings:
1. Reserve a DHCP-provided IP address for the host device.
Internet > DHCP tab
o On the DHCP tab, click the "+" (Add) button to enter DHCP Reservations.
o Description: <enter the desired description of the host device>
o Reserve address by: MAC Address
o Click Continue.
o MAC Address: <enter the MAC (what Apple calls Ethernet ID if you are using wired or AirPort ID if wireless) hardware address of the host computer>
o IPv4 Address: <enter the desired IP address>
o Click Done.
2. Setup Port Mapping on the AEBSn.
Advanced > Port Mapping tab
o Click the "+" (Add) button
o Service: <choose the appropriate service from the Service pop-up menu>
o Public UDP Port(s): <enter the appropriate UDP port values>
o Public TCP Port(s): <enter the appropriate TCP port values>
o Private IP Address: <enter the IP address of the host server>
o Private UDP Port(s): <enter the same as Public UDP Ports or your choice>
o Private TCP Port(s): <enter the same as Public TCP Ports or your choice>
o Click "Continue"
(ref: "Well Known" TCP and UDP ports used by Apple software products)

Port forwarding for clientless SSL VPN access

Hello,
I am currently trying to set up clientless SSL VPN access for some remote sites that our company does business with. Since their machines are not owned by my company, we don't want to install/support a VPN client. Therefore, SSL is a great option.
However, I'm running into an issue. I'm trying to set up port forwarding for a few remote servers. These remote servers are different and have distinct IP addresses. They are attempting to connect with two different servers here.
But my issue is that both servers are trying to use the same TCP port. The ASDM is not letting me use two different port forwarding rules for the same TCP port. The rules can exist side-by-side, but they cannot be used at the same time.
Why? It's not trying to access the same TCP port on a server when it's already in use. Is there anyway I can get around this?
If this doesn't make sense, please let me know and I'll do my best to explain it better.

Hi Caleb,
if you mean clientless webvpn port-forwarding lists, then you should be able to get your requirments. even the same port of the same server can be mapped to different ports bound to the loopback IP.
CLI:
ciscoasa(config) webvpn
ciscoasa(config-webvpn)# port-forward PF 2323 192.168.1.100 23
ciscoasa(config-webvpn)# port-forward PF 2300 192.168.1.200 23
then you apply the port-forwarder list under a group-policy
Hope this helps
Mashal
Mashal Alshboul

Port Forwarding for L2TP/IPSec VPN Behind Verizon Actiontec MI424WR-GEN2 Rev. E v20.21.0.2

I've got a NAS setup with various services running on custom ports to help minimize exposure (especially to script kiddies). I've tested everything both internally and externally to confirm they all work, and even had someone at a remote location confirm accessibility as well. Port forward configurations performed on the Actiontec are working well.
I installed an L2TP/IPSec VPN server, tested internally and it connected successfully. So for all intents & purposes, this validates that the VPN server is correctly configured to accept inbound connections and functioning correctly.
I logged into the Verizon Actiontec MI424WR router, setup port forwarding for UDP ports 500, 1701 & 4500.
Note: I added the AH & ESP protocols based on what I saw on the built-in L2TP/IPSec rules
With the port forwarding in place, I tested VPN externally but it didn't connect.
I've done the following so far to no avail:
Double & triple checked the port forwards, deleted & recreated the rules a few times to be sure
There are no other pre-existing L2RP/IPSec port forward rules or otherwise conflicting port forward rules (e.g.: another rule for ports 500, 1701 or 4500)
There was an L2TP port triggering rule enabled, that I toggled on and off with no change
Verified the firewall on VPN server had an exclusion for L2TP, or that the firewall is off. (Firewall is off to reduce a layer of complexity, but it worked internally to begin with so I doubt that's the issue.)
Since it works internally, and there are no entries in the logs on the device indicating inbound connections, I'm convinced its an issue with the Verizon Actiontec router. But unfortunately, I'm not sure what else to try or where else to look to troubleshoot this. For instance, is there a log on the router that I can view in real time (e.g.: tail) that would show me whether or not the inbound connection attempt is reaching the device, and whether or not the device allowed or blocked it?
My router details:
Verizon Actiontec
MI424WR-GEN2
Revision E
Firmware 20.21.0.2
Verizon Actiontec built-in L2TP/IPSec rule templates. They're not currently in use, but are baked into the firmware for easy configuration/selection from a drop down menu.
Solved!
Go to Solution.

normally a vpn on that router, will have a GRE tunneling protocol as well.
two ways to build the PF rules,
Manually
Preconfigured
I know the preconfigured VPN rules will do the GRE protocol as well, but if you do it by hand you can't get it.

Problems with Port Forwarding for RDP in WebVPN

Hi,
I'm hoping somebody can help me solve this problem that's been bugging for weeks. We recently implemented a double-layer firewall architecture. Before that, our users can access RDP via port forwarding on WebVPN or the Cisco VPN client without any problems.
After we implemented the double-layer firewall architecture, users who are going through the WebVPN and port forwarding for RDP began to experience frequent disconnections, slowness or freezing connections. The users who are using the client are fine.
I checked the logs and I'm getting repetitive TCP-O for the port forwarding connections for RDP. Additional information: the FW we installed as a 2nd layer is Netscreen. I've already set the policy on it to Any-Any for the meantime to help in troubleshooting but to no avail.
I hope somebody can help me in sorting this out as I'm kind of confused on the difference between the port-forwarding for RDP via the WebVPN and the normal RDP via the client.

Hi,
I didnt see anything marked with red in the above? (Atleast when I was reading)
I have not really had to deal with Routers at all since we all access control and NAT with firewalls.
But to me it seems you have allowed the traffic to the actual IP address of the internal server rather than the public IP NAT IP address which in this case seems to be configured to use your FastEthernet4 interfaces public IP address.
There also seems to be a Static NAT configured for the same internal host so I am wondering why the Static PAT (Port Forward) is used?
- Jouni

I have the new Air Port Extreeme model A1521 and I need to set up port forwarding for HTTP. HTTP is not on the list in the set up. Does anyone know if any of those choices work for HTTP?

I am on a Windows 7 Ultimate PC and right now there is no Airport utility for setting up the new Apple Extreme so you have to do it on your iPad or iPhone. Does anyone know how to set up port forwarding for HTTP to get to DVR security cameras? There is nothing in the list that indicates HTTP port forwarding.

Thanks for your reply Tesserax as I did figure this out on my own. It took a bit because all of the options are not clear what they are for like the previous Airport Extreme and Apple does not support or guarantee that port forwarding will work for you application nor did any of the Apple support persons I spoke too have any knowledge for this feature. You also have to fill in the public if you are viewing through someone else's Wi-Fi or on your cell phone carrier network. This new Airport Extreme is a bit different since you cannot use the Airport utility on a PC like the older model and if anyone else is reading this they should be aware that if you do not have an Apple computer, iPhone or iPad and I'm not sure if some of the other network enabled devices like iPod Touch that you must use that can do it, there is no Airport utility for the PC and you would be wasting your money or have to take it back and get another brand wireless router to use if you do not own any of the above mentioned Apple products.

Not enough port fields in port forwarding for Linksys E4200

I have always used netgear routers in the past. After a series of issues regarding configurations not working correctly I invested in what appeared to be a semi pro router, the cisco linksys e4200.
I have a centralized server which I use to access a mass of different services such as mail, dns, VPN, FTP, Kerberos, http and many more. While I am not a massive networking nerd, this server setup is like my garage project. To access these services externally to my LAN as far as I understand I would need to configure port forwarding for each service to my server. Unfortunately the control panel for the linksys E4200 only offers about 15 custom port fields for forwarding, and some documentation I have read shows that with it's basic install my server could be using up to 60 ports at once.
Is this router just not suitable for this sort of network. If so I will be very disappointed because I have spent a quarter of the price on netgear routers with more control than this.
If anybody could assist with details and options I would greatly appreciate it

Wrong forum, use "small business routers".

I authorized my home sharing on my itunes for mac to share to my itunes on windows PC, but for some reason my music isn't fully sharing/syncing. Does anyone know how I can solve this problem?

I authorized my home sharing on my itunes for mac to share to my itunes on windows PC, but for some reason my music isn't fully sharing/syncing. Does anyone know how I can solve this problem?

Hi, Dave.
If you're using the BlackBerry browser, you can't configure anything to bypass the RIM servers. I believe you may do so by using the Opera browser, but I haven't tried it myself so cannot comment with authority.
I hope that clears up the issue for you.
- If my response has helped you, please click "Options" beside my post and mark it as solved. Clicking the "thumbs up" icon near the bottom of my response would also be appreciated.

TS2972 How do you port forward for Home Sharing ?

I want to home share with my apple tv and it's not working, so i think i need to port forward for home sharing on my apple tv. But i dont know how to port forward :S

I use an application called port map. http://www.codingmonkeys.de/portmap/ Make sure you download the landlubbers version. When you open it add a port called minecraft with the port 25565

Please recommend personal finance software for Mac that allows month to month analysis of spending by categories. Quicken on a PC was good at this. Mint seems very limited.

Please recommend personal finance software for Mac that allows month to month analysis of spending by categories. Quicken on a PC was good at this. Mint seems very limited.

Quicken for Mac 2007 works just fine (and is said to be compatible with Mavericks). It is often denounced for not being "modern", but when something works, and does everything I want, I need a good reason to switch.
A few years ago (2011), I got that reason when I upgraded OSX and Quicken stopped working due to the absence of Rosetta. I switched to iBank. I used it for more than a year. It was cumbersome, they have no sense of a helpful user interface, but it "works". I found ONE feature that I liked: you can attach an image (or any file) to a register entry, so I can save receipts right with the register.
But when Intuit came out with the revised Quicken 2007 for Mountain Lion, I gladly went back. I found that being able to update stock prices right in the portfolio view (for those not automatically found online) was handy - in iBank you have to generate a report to see the holdings, and then you have to switch to a view of "Securities" then scroll down through that list to find your stock, then "edit" then change the price, then "Save" then go back to reports and re-generate the portfolio view. Also, if you enter a stock purchase in a Quicken register, the price you paid gets added to the price history for the stock (as of the date of the transaction). No such help in iBank. Most of the helpful UI features (like increasing the date with the + key) are glaringly missing in iBank. I find I am getting no more than about 3-4 keystrokes before having to move the mouse and click.
If you are considering sharing the app on an iPad, Quicken won't work, but I found that iBank for iPad doesn't work either. The interface is completely different from the Mac version, you can't do much with it, and if you have a stock whose price is $11.25 / share and sell 200 shares, you might find that $22.50 gets added to your cash in the account. (I actually made a few million dollars when it decided that 200 shares at $11.25 yielded $2,250,000.) Luckly, I received a refund for that app.
Depending on how the Mavericks switch goes, I hope to be able to stick with Quicken, but I am keeping my records up-to-date in both now, because I can live with iBank. I will just have to keep an eye on its arithmetic.

Homehub 5 port forwarding for Windows Homeserver 2...

Hi
Has anybody any solutions on setting up the HH5 for Windows Homeserver 2011
I've inputted all the rules manually as WHS couldn't complete the task, to find ports 80, 443, 4125 remain closed after manual input.
WHS reply's with UPnP not working / router not working.
BT customer services quite appalling and I'm not paying for Tech Support as the package is only 6 months old and I feel I shouldn't have to pay for a product that isn't working correctly, if it was over 12 months I understand I should pay.
I've manually inputted and setup port forwarding for my Iphone app and Android and they've finally started working.
Cheers
Solved!
Go to Solution.

Can you just put WHS in the DMZ on the HH5?
If you found this post helpful, please click on the star on the left
If not, I'll try again

Help with port forwarding for the WRT54G

I need assistance please!
I am having issues trying to setup port forwarding for a ftp. I already have set this up for a SQL Server port and it works remotely. When I setup another rule for ftp using port range 20-21 it does not work.
I have confirmed that I have saved my settings, have the correct IP address, etc. I have firmware version 4.21.1 and not sure how to troubleshoot this. Any help would be great.
Thanks,
John

Yes you do need to have the port already forwarded for port 20~21 with both TCP/IP and UDP enabled unless you know for sure your ftp only uses just one of them. That is why I asked what port your SGL was set to. Follow the link that other guy posted and open port 20 and 21 (I only use 21 with no problems) and make sure it is directed to the IP of the ftp host. Also that PC needs to have the FTP enabled in windows. To do that go to your control panel > add/remove software > and on the left side go to add/remove windows components. Then check the box for the ftp and add it. It should ask for your windows CD do have it handy when you add the ftp component to your PC.
Richard Aichner (Ikester)

Can I load Office for Mac via the internet? I own the disks and have only loaded them twice.

Can I load Office for Mac via the internet? I own the disks and have only loaded them twice.

If you are saying that you have one license left of a three license edition MS Office for Mac 2011, then all you have to do is download a MS Office trial for Mac from the MS website. Using the available license registration number, you can activate the downloaded trial and have the same functionality as if you had used the disks and registered with that same number.

Port forwarding for Mac that shares internet to Airport in bridge mode?

Similar Messages

Maybe you are looking for