Port Forwarding Question for IP Camera with MI424WR-GEN3

So just switched to fios from cable and trying to set up port forwarding on this new actiontec router so I can view my IP Camera from outside the house.
The camera has a static IP address of 192.168.1.200 using port 8080 and I works fine if I type that IP address with the port into the browser inside the network.
The IP Camera company requires you to port forward port 80 (switched to 8080) 554 and 50000-60000.
So I set up Portforwarding on the router like this:
Networked Computer / Device
192.168.1.200:8080
Applications & Ports Forwarded
IPCamera
TCP 8080 -> 8080
UDP 8080 -> 8080
TCP 554 -> 554
UDP 554 -> 554
TCP 50000-60000 -> 50000-60000
UDP 50000-60000 -> 50000-60000
WAN Connection Type
All Broadband Devices
Status
Active
Now the problem is when I type my real IP address: 108.XX.XXX.37:8080 (from inside the network it pulls up the Fios router login page and when I pull it up outside the network I get page not found. This isnt any different then I had previously done on my Netgear router, but I must be missing something on this actiontec one. Any suggestions?
Thanks
Solved!
Go to Solution.

Howie411 wrote:
The IP Camera company requires you to port forward port 80 (switched to 8080) 554 and 50000-60000.
So I set up Portforwarding on the router like this:
Networked Computer / Device
192.168.1.200:8080
Applications & Ports Forwarded
IPCamera
TCP 8080 -> 8080
UDP 8080 -> 8080
TCP 554 -> 554
UDP 554 -> 554
TCP 50000-60000 -> 50000-60000
UDP 50000-60000 -> 50000-60000
WAN Connection Type
All Broadband Devices
Status
Active
Now the problem is when I type my real IP address: 108.XX.XXX.37:8080 (from inside the network it pulls up the Fios router login page and when I pull it up outside the network I get page not found. This isnt any different then I had previously done on my Netgear router, but I must be missing something on this actiontec one. Any suggestions?
Thanks
No port on the ip address
Networked Computer / Device
192.168.1.200
should say tcp any on the left side of the arrow in all cases
TCP any -> 8080
UDP any -> 8080
etc

Similar Messages

Simple Port Forwarding Question

Sorry if this has been asked and answered many times before but I I've been at this for hours and I'm getting nowhere.
We have a Cisco 861 router. I've taken over the IT responsibilities from someone else and I'm just trying to forward TCP/UDP ports 5899 and 9010 to our server. I can access the server using Remote Desktop so I can see the previous IT person has gotten that far. Below is the output of our "Running Configuration".
I can see the line "ip port-map user-protocol--4 port tcp 3389" but I can't figure out how to add my own 5899 and 9010 lines.
I'm using the Cisco Configuration Professional UI but I don't have a problem using the command line interface if I'm sure I have the right commands to input. I started adding an extended rule using the ACL Editor in CCP but I'm afraid to deliver the changes to the router because it doesn't look anything like the "ip port-map user-protocol--4 port tcp 3389" line.
Here is the information generated from the ACL editor (again, I haven't delivered it to the router):
ip access-list extended user-protocol--05
remark Radmin5899
remark CCP_ACL Category=1
remark Radmin5899
permit tcp any host 10.10.10.10 eq 5899
exit
I don't think the ACL output is correct because I don't see the public IP.
How do I create a cusom ip port-map like the ones listed in the "Running Configuration"?
Any help would be greatly appreciated.
Kevin G
Running Configuration:
Building configuration...
Current configuration : 10177 bytes
! Last configuration change at 09:45:33 PCTime Fri Feb 21 2014 by admin
version 15.0
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
hostname Summit
boot-start-marker
boot-end-marker
logging buffered 51200
logging console critical
enable secret 5 $1$q6Ct$Wo7VDTQAbAL7BjYEvSXvJ/
no aaa new-model
memory-size iomem 10
clock timezone PCTime -5
clock summer-time PCTime date Apr 6 2003 2:00 Oct 26 2003 2:00
crypto pki trustpoint TP-self-signed-1582036946
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1582036946
revocation-check none
rsakeypair TP-self-signed-1582036946
crypto pki certificate chain TP-self-signed-1582036946
certificate self-signed 01
30820249 308201B2 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31353832 30333639 3436301E 170D3933 30333031 30303030
34365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 35383230
33363934 3630819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100A98F 75C0DEE6 FA35B0D2 3F42C711 3E622144 312E5DEC 8A721820 1E25EDCB
A8F10958 4DE48A8D AF5C0297 92526567 DCCCECC8 165C7A66 9CFF76C1 E8083FE2
807FD489 4A8EEF92 5528F079 F069690E 3F3A269B 4D948A32 E9F556B0 5AE8DC1A
9F753D60 58E0A298 1D1045C2 641D5976 E857FAE8 C853CF31 24356154 828F98E2
913D0203 010001A3 71306F30 0F060355 1D130101 FF040530 030101FF 301C0603
551D1104 15301382 1153756D 6D69742E 73706D63 2E6C6F63 616C301F 0603551D
23041830 16801436 F9B786F7 EB0AE78E DE16D0D8 EED4E8D5 E4679830 1D060355
1D0E0416 041436F9 B786F7EB 0AE78EDE 16D0D8EE D4E8D5E4 6798300D 06092A86
4886F70D 01010405 00038181 007B2A5E E5180062 70FD14E5 A1B9C29D C20C99D4
5897D077 B4F4250E 6788CF79 4640E214 C112724B 7EB04A9D 0754956E 2D5AF34A
0C1D1A6E 86AC0E07 FFFBEC66 B8DA4E35 E05B2AA9 F8FD084C A23A2E21 A92C409E
9AA9C45A F2B406BC E123869A 2989FBDD 65E96A95 8D6CB6C9 BAF33F75 19999CB3
4F8613BB 40251384 2D30F8A1 82
 quit
no ip source-route
ip port-map user-protocol--2 port tcp 100
ip port-map user-protocol--1 port tcp 101
ip port-map user-protocol--4 port tcp 3389
ip dhcp excluded-address 10.10.10.1 10.10.10.100
ip dhcp pool spmcpool
 network 10.10.10.0 255.255.255.0
 domain-name spmc.local
 dns-server 10.10.10.10 8.8.8.8
 default-router 10.10.10.1
ip cef
no ip bootp server
no ip domain lookup
ip domain name spmc.local
license udi pid CISCO861-K9 sn FTX1446810J
username admin privilege 15 secret 5 $1$W2UZ$IvcuhFV2mkG0u/RI.XwUN0
username spmc privilege 15 secret 5 $1$P88u$ZEG5RuEVxxAaTXW3BQ1q3/
ip tcp synwait-time 10
ip ssh time-out 60
ip ssh authentication-retries 2
class-map type inspect match-any SDM_BOOTPC
match access-group name SDM_BOOTPC
class-map type inspect match-all sdm-nat-user-protocol--4-1
match access-group 102
match protocol user-protocol--4
class-map type inspect match-all sdm-nat-user-protocol--2-1
match access-group 104
match protocol user-protocol--2
class-map type inspect match-all sdm-nat-http-1
match access-group 102
match protocol http
class-map type inspect match-all sdm-nat-user-protocol--1-2
match access-group 103
match protocol user-protocol--1
class-map type inspect match-all sdm-nat-user-protocol--1-1
match access-group 102
class-map type inspect match-any SDM_DHCP_CLIENT_PT
match class-map SDM_BOOTPC
class-map type inspect match-all sdm-nat-smtp-1
match access-group 102
match protocol smtp
class-map type inspect match-any sdm-cls-bootps
match protocol bootps
class-map type inspect match-any ccp-cls-insp-traffic
match protocol cuseeme
match protocol dns
match protocol ftp
match protocol h323
match protocol https
match protocol icmp
match protocol imap
match protocol pop3
match protocol shell
match protocol realmedia
match protocol rtsp
match protocol smtp
match protocol sql-net
match protocol streamworks
match protocol tftp
match protocol vdolive
match protocol tcp
match protocol udp
class-map type inspect match-all ccp-insp-traffic
match class-map ccp-cls-insp-traffic
class-map type inspect match-any ccp-cls-icmp-access
match protocol icmp
class-map type inspect match-all ccp-icmp-access
match class-map ccp-cls-icmp-access
class-map type inspect match-all ccp-invalid-src
match access-group 100
class-map type inspect match-all sdm-nat-https-1
match access-group 102
match protocol https
class-map type inspect match-all ccp-protocol-http
match protocol http
policy-map type inspect ccp-permit-icmpreply
class type inspect sdm-cls-bootps
pass
class type inspect ccp-icmp-access
inspect
class class-default
pass
policy-map type inspect sdm-pol-NATOutsideToInside-1
class type inspect sdm-nat-http-1
inspect
class type inspect sdm-nat-smtp-1
inspect
class type inspect sdm-nat-user-protocol--4-1
inspect
class type inspect sdm-nat-https-1
inspect
class type inspect sdm-nat-user-protocol--1-2
inspect
class type inspect sdm-nat-user-protocol--2-1
inspect
class class-default
drop
policy-map type inspect ccp-inspect
class type inspect ccp-invalid-src
drop log
class type inspect ccp-protocol-http
inspect
class type inspect ccp-insp-traffic
inspect
class class-default
drop
policy-map type inspect ccp-permit
class type inspect SDM_DHCP_CLIENT_PT
pass
class class-default
drop
zone security out-zone
zone security in-zone
zone-pair security ccp-zp-self-out source self destination out-zone
service-policy type inspect ccp-permit-icmpreply
zone-pair security ccp-zp-in-out source in-zone destination out-zone
service-policy type inspect ccp-inspect
zone-pair security ccp-zp-out-self source out-zone destination self
service-policy type inspect ccp-permit
zone-pair security sdm-zp-NATOutsideToInside-1 source out-zone destination in-zone
service-policy type inspect sdm-pol-NATOutsideToInside-1
interface FastEthernet0
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface FastEthernet4
description Internet$FW_OUTSIDE$$ES_WAN$$ETH-WAN$
ip address 66.x.x.x 255.255.255.248
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip flow egress
ip nat outside
ip virtual-reassembly
zone-member security out-zone
duplex auto
speed auto
interface Vlan1
description LAN$FW_INSIDE$$ES_LAN$$ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$
ip address 10.10.10.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat inside
ip virtual-reassembly
zone-member security in-zone
ip tcp adjust-mss 1452
ip default-gateway 66.x.x.x
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip flow-top-talkers
top 20
sort-by bytes
ip nat inside source list 3 interface FastEthernet4 overload
ip nat inside source static tcp 10.10.10.100 100 66.x.x.x 100 extendable
ip nat inside source static tcp 10.10.10.101 101 66.x.x.x 101 extendable
ip nat inside source static tcp 10.10.10.10 25 66.x.x.x 25 extendable
ip nat inside source static tcp 10.10.10.10 80 66.x.x.x 80 extendable
ip nat inside source static tcp 10.10.10.10 443 66.x.x.x 443 extendable
ip nat inside source static tcp 10.10.10.10 3389 66.x.x.x 3389 extendable
ip nat inside source static tcp 10.10.10.10 5899 66.x.x.x 5899 extendable
ip nat inside source static tcp 10.10.10.10 9010 66.x.x.x 9010 extendable
ip nat inside source static udp 10.10.10.10 9010 66.x.x.x 9010 extendable
ip nat inside source static 10.10.10.10 66.x.x.x
ip route 0.0.0.0 0.0.0.0 FastEthernet4 66.x.x.x
ip access-list extended SDM_BOOTPC
remark CCP_ACL Category=0
permit udp any any eq bootpc
logging trap debugging
access-list 1 remark INSIDE_IF=Vlan1
access-list 1 remark CCP_ACL Category=2
access-list 1 permit 10.10.10.0 0.0.0.255
access-list 2 remark CCP_ACL Category=2
access-list 2 permit 10.10.10.0 0.0.0.255
access-list 3 remark CCP_ACL Category=2
access-list 3 permit 10.10.10.0 0.0.0.255
access-list 100 remark CCP_ACL Category=128
access-list 100 permit ip host 255.255.255.255 any
access-list 100 permit ip 127.0.0.0 0.255.255.255 any
access-list 101 remark CCP_ACL Category=16
access-list 101 permit ip 10.10.10.0 0.0.0.255 any
access-list 102 remark CCP_ACL Category=0
access-list 102 permit ip any host 10.10.10.10
access-list 103 remark CCP_ACL Category=0
access-list 103 permit ip any host 10.10.10.101
access-list 104 remark CCP_ACL Category=0
access-list 104 permit ip any host 10.10.10.100
no cdp run
snmp-server community agsl RO
control-plane
banner exec ^C
% Password expiration warning.
Cisco Configuration Professional (Cisco CP) is installed on this device
and it provides the default username "cisco" for one-time use. If you have
already used the username "cisco" to login to the router and your IOS image
supports the "one-time" user option, then this username has already expired.
You will not be able to login to the router with this username after you exit
this session.
It is strongly suggested that you create a new username with a privilege level
of 15 using the following command.
username <myuser> privilege 15 secret 0 <mypassword>
Replace <myuser> and <mypassword> with the username and password you
want to use.
^C
banner login ^CAuthorized access only!
Disconnect IMMEDIATELY if you are not an authorized user!^C
line con 0
login local
no modem enable
transport output telnet
line aux 0
login local
transport output telnet
line vty 0 4
privilege level 15
login local
transport input telnet ssh
scheduler max-task-time 5000
scheduler allocate 4000 1000
scheduler interval 500
end

Turns out, through some quirk of either Java, IE or CCP, the "Port to Application Mappings" page was blank. I added the necessary application protocol and it worked for opening a port I needed open on the server. Even with the screen blank I could click on the blank area in different spots and the "Edit..." button would become available. For whatever reason, whenever I go into CCP now, the page is no longer blank.
I'm having a different problem now with opening ports for our camera DVR. I'll start a new thread for that.
Thanks for the help.

New network/port forwarding questions

I just replaced my Airport Extreme with a 1TB TC and set up a primary network (AirNett) and a Guest network (Guest). I added Port Mapping entries for my computers (running Tiger), SlingBoxes and ReplayTVs (which are all ethernet-connected) and I have 1 laptop running Leopard and 1 running Tiger. We also have 2 iPhones.
The wired devices all seem to connect just fine. Occasionally, there is a delay in the connection (30 sec-1 min), but once it connects, they seem to stay connected.
The laptops take too long to connect to the AirNett network. If they do connect, it seems that the connection comes and goes. The iPhones have yet to connect to AirNett.
The Guest network serves all the wireless devices just fine, BUT, it does not allow connections to the Port Forwarding devices.
So, 2 issues... any ideas about :
1) why my primary network (AirNett) is not working properly for my wireless devices and
2) why my Guest network does not allow the Port Forwarding connections.
TIA for any suggestions.
Scott

That was my point - all my lan ports that use port 80 can point at port 80, and long as the WAN ports point at something else. The trouble is, I am restricted to only using 80,81 and 443 on the LAN side, which limits me to 3 (not counting 8080 for my routers web gui)
So that means with my two web cams and web gui on my NAS drive, I am unable to log into any other web interfaces on my LAN, unless I log into my router first, disable one port forward and enable another (using the same WAN port of 80 or 81) - which is doable but a PITA..
This is what is looks like on the router:
For example, if I change the port from field for the "tranmission" entry to anything but 80 or 81, it will not work, so if I want to get into my torrent gui on my NAS drive I have to disable "cam1" and enable "transmission"
I checked with my ISP and they are not blocking any ports, so I'm not sure how to get around this, unless I can serve up a page that shows feeds from more than one camera and serve it from one source, ie my router or NAS drive.

Port Forwarding Question - Detailed

Hi,
I hate wasting people's time, so I will give you very detailed information.
So here's an overview of the network. I have a WRT54G with V4.21 firmware on it. I also have a WRE54G Range Expander. Both are secured. We have 3 desktops, 2 laptops, and some game consoles hooked up to the wireless internet, with nothing connected with an ethernet cable (all wireless).
A friend and myself want to play an online game, which requires one person to be a server, and one to be a client. He doesn't have access to his network configurations, so I will end up being the server.
I have setup port forwarding, and the program gives me a Socket Error of 10061 - Connection was refused forcefully.
The port is 1001 that we need open.
I have checked with my ISP, and have found that they are not blocking any ports, so I know that is not an issue.
If I hook the computer up directly to the modem, it works fine, so it is definitely a forwarding issue.
I have DHCP turned off on the computer, my local IP address is 192.168.1.106
My port forwarding settings look like this.
Application: (Blank... but I have used other names during tests)
Start: 1001
End: 1001
Protocol: Both (I have also tried TCP and UDP individually)
IP Address: 192.168.1.106 (my static IP address)
Enabled: True
I have also tried turning the SPI Firewall Protection off, as well as Block Anonymous Internet Requests.
The IP address that the person is using to connect to the computer with is my router's IP address (which is propagated directly from the modem). With the port 1001. This is the same combination used when the computer is hooked up directly to the modem, however with it behind the router, the forwarding just doesn't seem to handle the forward.
I have tried it with Windows Firewall turned off, as well as my Norton AV.
I have also created exceptions and completely opened port 1001 in Windows Firewall just in case.
I've also tried just simply restarting the computer.
I'm tapped out of ideas... can anyone else suggest anything?
Message Edited by Joker_69 on 05-13-2008 01:53 AM

Alright, I went through the checklist, and every single step in the checklist checked out, except for connecting from outside the LAN. I can connect to the server through 192.168.1.150:1001, but not through xxx.xxx.96.215:1001.
Here are all settings that have been changed (everything else should be assumed to be default values):
Wireless/Security:
Security Mode: WEP
Default Transmit Key: 1
WEP Encryption: 128 bits 26 hex digits
Passphrase: Have been set
Key 1, 2, 3, 4: Have been set
Security/Firewall:
Firewall Protection: Disable
Block Anonymous Internet Requests: False
Filter Multicast: True
Filter Internet NAT Redirection: False
Filter IDENT(Port 113): True
Applications & Gaming/Port Range Forward:
Application: (no name given)
Start: 1001
End: 1001
Protocol: Both (TCP & UDP)
IP Address: 192.168.1.150
Enable: True
Now, here is the Status Page of the Router:
Firmware Version: v4.21.1, Nov. 6, 2006
Current Time: Tue, 13 May 2008 23:47:26
MAC Address: xx:xx:xx:02:11:F5
Router Name: WRT54G
Host Name:
Domain Name:
Login Type: Automatic Configuration - DHCP
IP Address: xxx.xxx.96.215
Subnet Mask: 255.255.192.0
Default Gateway: xxx.xxx.64.254
DNS 1: xxx.xxx.133.68
DNS 2: xxx.xxx.133.100
DNS 3:
MTU: 1500
Here is the copy from ipconfig /all (with IP's blocked out):
Windows IP Configuration
Host Name . . . . . . . . . . . . : xxxxx-xxxxxxxxx
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Unknown
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
Ethernet adapter Wireless Network Connection:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Wireless-B PCI Adapter
Physical Address. . . . . . . . . : xx-xx-xx-0D-39-EC
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.1.150
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.1.1
DNS Servers . . . . . . . . . . . : xxx.xx.133.68
xxx.xxx.133.100
Here is my netstat -an:
Active Connections
Proto Local Address Foreign Address State
TCP 0.0.0.0:25 0.0.0.0:0 LISTENING
TCP 0.0.0.0:80 0.0.0.0:0 LISTENING
TCP 0.0.0.0:135 0.0.0.0:0 LISTENING
TCP 0.0.0.0:443 0.0.0.0:0 LISTENING
TCP 0.0.0.0:445 0.0.0.0:0 LISTENING
TCP 0.0.0.0:1001 0.0.0.0:0 LISTENING
TCP 0.0.0.0:1025 0.0.0.0:0 LISTENING
TCP 0.0.0.0:2869 0.0.0.0:0 LISTENING
TCP 0.0.0.0:5051 0.0.0.0:0 LISTENING
TCP 0.0.0.0:5101 0.0.0.0:0 LISTENING
TCP 0.0.0.0:7501 0.0.0.0:0 LISTENING
TCP 0.0.0.0:21159 0.0.0.0:0 LISTENING
TCP 127.0.0.1:1026 0.0.0.0:0 LISTENING
TCP 127.0.0.1:1045 0.0.0.0:0 LISTENING
TCP 127.0.0.1:3668 127.0.0.1:3669 ESTABLISHED
TCP 127.0.0.1:3669 127.0.0.1:3668 ESTABLISHED
TCP 127.0.0.1:3670 127.0.0.1:3671 ESTABLISHED
TCP 127.0.0.1:3671 127.0.0.1:3670 ESTABLISHED
TCP 192.168.1.150:139 0.0.0.0:0 LISTENING
TCP 192.168.1.150:4153 xxx.xxx.193.131:119 ESTABLISHED
TCP 192.168.1.150:4156 xxx.xxx.233.145:5050 ESTABLISHED
TCP 192.168.1.150:4170 xxx.xxx.107.81:1863 ESTABLISHED
TCP 192.168.1.150:4949 xxx.xxx.207.191:80 CLOSE_WAIT
TCP 192.168.1.150:4950 xxx.xxx.223.191:80 CLOSE_WAIT
TCP 192.168.1.150:4951 xxx.xxx.139.166:80 CLOSE_WAIT
TCP 192.168.1.150:4952 xxx.xxx.139.166:80 CLOSE_WAIT
TCP 192.168.1.150:4953 xxx.xxx.255.103:80 CLOSE_WAIT
UDP 0.0.0.0:445 *:*
UDP 0.0.0.0:500 *:*
UDP 0.0.0.0:1048 *:*
UDP 0.0.0.0:1050 *:*
UDP 0.0.0.0:1166 *:*
UDP 0.0.0.0:1178 *:*
UDP 0.0.0.0:1802 *:*
UDP 0.0.0.0:1803 *:*
UDP 0.0.0.0:1804 *:*
UDP 0.0.0.0:1805 *:*
UDP 0.0.0.0:1806 *:*
UDP 0.0.0.0:3456 *:*
UDP 0.0.0.0:4500 *:*
UDP 0.0.0.0:5051 *:*
UDP 127.0.0.1:123 *:*
UDP 127.0.0.1:1900 *:*
UDP 127.0.0.1:2089 *:*
UDP 127.0.0.1:2111 *:*
UDP 127.0.0.1:3459 *:*
UDP 192.168.1.150:9 *:*
UDP 192.168.1.150:123 *:*
UDP 192.168.1.150:137 *:*
UDP 192.168.1.150:138 *:*
UDP 192.168.1.150:1900 *:*
UDP 192.168.1.150:4160 *:*
UDP 192.168.1.150:4161 *:*
UDP 192.168.1.150:4163 *:*
UDP 192.168.1.150:4164 *:*
UDP 192.168.1.150:8163 *:*
UDP 192.168.1.150:39358 *:*
The sixth one down from the top looks like it is working properly.
Let me know what you think .
Message Edited by Joker_69 on 05-14-2008 12:01 AM

EA2700 port forwarding issues for DVR access

So start this off I searched these forums for answers and new here but not to the router world, I have been having issues lately I set up a DVR and need to view remotely, ports are 7000 and 8080, I setup DVR on a static IP and it can access the internet and I can ping the DVR internally than I go into router and port forward those ports on DVR's IP address disabled upnp I setup dhcp reservation on DVR's IP but when I check can you see me.org it shows those ports are closed for my external than I check port 80 and shows closed looks like all my ports are close is there some firewall in this router that would do this please help

If the ISP modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems: Link>http://www.practicallynetworked.com/networking/fixing_double_nat.htm and http://cognitiveanomalies.com/cisco-nat-how-nat-works/. If the modem can't be bridged then see if the modem has a DMZ option and input the IP address the router gets from the modem and put that into the modems DMZ.
Glad you got it working. Enjoy.
loginix wrote:
So start this off I searched these forums for answers and new here but not to the router world, I have been having issues lately I set up a DVR and need to view remotely, ports are 7000 and 8080, I setup DVR on a static IP and it can access the internet and I can ping the DVR internally than I go into router and port forward those ports on DVR's IP address disabled upnp I setup dhcp reservation on DVR's IP but when I check can you see me.org it shows those ports are closed for my external than I check port 80 and shows closed looks like all my ports are close is there some firewall in this router that would do this please help

I just got new lenovo with windows8.1, toolbar for this came with microscopic title bar size

just returned asus zenbook and bought lenovo yoga, it came with big differnce on title bar font size only on mozilla browser. when i oppened new window, icons on very top right corner (minimize, restore down, close) are microscopic. i know how to enlarge buttons itself and it work , but icons remain same size. Then i downloaded adobe flash player for live streaming. It came with toolbar on the side, which is impossible to read without magnifier. Opened Explorer to compare- everything in normal (large) font . First time i see it, is there any solution?

Can you attach a screenshot?
*http://en.wikipedia.org/wiki/Screenshot
*https://support.mozilla.org/kb/how-do-i-create-screenshot-my-problem
*Use a compressed image type like PNG or JPG to save the screenshot
*Make sure that you do not exceed the maximum size of 1 MB
I'm not on Windows, so can't check if this code still works.
Add code to the userChrome.css file below the default @namespace line.
*http://kb.mozillazine.org/userChrome.css
<pre><nowiki>@namespace url("http://www.mozilla.org/keymaster/gatekeeper/there.is.only.xul"); /* only needed once */
#titlebar-buttonbox .titlebar-button { height: 24px !important; width: 24px !important; }
</nowiki></pre>
The customization files userChrome.css (user interface) and userContent.css (websites) are located in the chrome folder in the Firefox profile folder.
*http://kb.mozillazine.org/Editing_configuration
You can use this button to go to the currently used Firefox profile folder:
*Help > Troubleshooting Information > Profile Directory: Show Folder (Linux: Open Directory; Mac: Show in Finder)
*Create the chrome folder (lowercase) in the <xxxxxxxx>.default profile folder if this folder doesn't exist
*Use a plain text editor like Notepad to create a (new) userChrome.css file in the chrome folder (file name is case sensitive)
*Paste the code in the userChrome.css file in the editor window
*Make sure that the userChrome.css file starts with the default @namespace line
*Make sure that you select "All files" and not "Text files" when you save the file via "Save file as" in the text editor as userChrome.css. Otherwise Windows may add a hidden .txt file extension and you end up with a not working userChrome.css.txt file

How to set properties for HTTPClient came with WSClient_extends.jar ?

In my web service client application, we need cookie to maintain session between server and client.
I think the server cookie policy is not completely standards compliant since HTTP request to this server through Apache HTTPClient need to setup following:
"http.protocol.single-cookie-header" to be true
cookie policy to be "CookiePolicy.BROWSER_COMPATIBILITY"
My problem is, we are using Oracle WSClient_extends.jar for web service call, WSClient_extends.jar came with it own HTTPClient implemetation.
Are there equlivant properties can be set in Oracle HTTPClient similar to Apache HTTPClient to handle such cookie policy?
Thanks

Hi,
This is correct; see my blog entry: http://db360.blogspot.com/2007/01/is-your-java-application-failoverproof.html
However, you need to use oracle.jdbc.pool.OracleDataSource and from what i know Websphere does not (yet?) allow bypassing its own connection pool in favor of Oracle driver's embedded conection pool.
Kuassi http://db360.blogspot.com

IOS port forwarding commands for Port Forwarding

I am trying to open up port 32400 on my 881w Cisco router but I have not had any success I need to configure manual port-forward to enable my Plex Media server. Can someone help me out wiht this set of cmds?
Thanks!

Hello Jonathan,
You have to configure ip nat inside on inside (LAN) interface and ip nat outside on WAN interface.
Then you canconfigure portforward:
ip nat insdie source static tcp 10.0.0.10 1122 150.0.0.1 2233
tcp - protocol, which you want to forward TCP/UDP
10.0.0.10 - IP address of your private device
1122 - port on your private device which you want access
150.0.0.1 - public IP which will represent your private device in internet
2233 - public port which will be forwarded to defined port on private device
Make sure that you do not filter traffic with ACL on your WAN or LAN interface.
Best Regards
Please rate all helpful posts and close solved questions

Question for using ORACLE with SOLARIS

Hi Experts,
I have worked Oracle with Linux in one of my projects 2yrs back and i was just a developer, used to write SQL Query, Creating Table and Objects.
Now i got a question from TL which is
Tell me about consequences for using Oracle with Solaris?
I am not worked ORACLE with SOLARIS, Can some one give me the answer for this question with
1. Difference between ORACLE with LINUX and ORACLE with SOLARIS.
2. Advantages and Disadvantages Between ORACLE with LINUX and ORACLE with SOLARIS.
Thanks,
MuraliDharan V

Hi MuraliDharan V,
It would had been better if you had searched first;
Here is one
Advantage for Linux64-bit Versus Solaris-x86_64 OS in RAC
And beside that your question is incomplete:
-What Oracle? Database, etc
-Which Version? 9i, 10g, etc
Aside from that a simple search on google might have answered your question as well.
But I think there is some new trend of dumping questions here before searching.
Ex Senior DBA

How can i disable the location for the camera with ios 6? since the update i cannot find out how to do this. i always have locations for my camera disabled for safety reasons. please help!

Please help! I upgraded to ios 6 today and I cannot find out where to disbale the location for the camera. I DO NOT want my pictures to be geotagged or have any type of location marked on them for safety reasons. Does anyone know how to disable it? Please help and thank you!

Bro try Setting then scrool down choose privacy then you find location service there you can turn off location service for camera. Gbu

Port Forward Question _ BT HomeHub 3

Hello all,
Ive been trying to set up port forwarding on my bt router but to no avail so far.
On the port forwarding tab in the router settings when I click Add to assign a device nothing happens??
Ive tried on my iphone and laptop and the "add" button turns grey but nothing happens?
Can anyone help?

so your selecting the "game or application" then selecting the "device" and the "ADD" button stays grey?
or can you select add but after selection and the page refreshing the new device doesnt show up?
under "supported applications" you can manually set up a device vis "new game or application" as a last resort

Port forwarding TSE for Cisco RV042G

Hi,
I just configured a Cisco RV042G small Business Routers on my network.
My problem is that I would like to permit TSE through the WAN1 and I am not able to do it.
I setup these informations from the menu :
- Setup / Forwarding
TSE[TCP/3389~3389]->192.168.1.15
- Firewall / Access Rules :
Allow TSE [3389] WAN1 192.168.1.15 ~ 192.168.1.11 192.168.1.15 ~ 192.168.1.15 Always
How can I configure it please ?
Thanks for you help.

Hello,
I'm sorry you are having issues with your device.
According to your explanation, you are trying to forward port 3389, Remote desktop, to a single device on your network with IP address 192.168.1.15.
If that is what you are trying to accomplish then:
1- You can delete the access rule as it is not needed on this device.
2- Make sure the rule that you created under Setup - Forwarding is enabled.
3- Make sure the computer with IP address 192.168.1.15 is using the IP address of the RV042G as the Default Gateway.
4- Go to your system summary page and check what the IP address of the WAN1 connection is, then, go to http://whatismyip.org and compare both addresses, if they are not the same then thats your problem. You will need to contact your ISP and ask them to put the modem on Bridge Mode so that all the traffic passes directly to the router.
I hope this helps. Please let us know.

TCP/UDP Port Utilization question for CCX 8.5

Greetings,
I have gone through the CCX 8.5 TCP/UDP port utilization guide.
http://www.cisco.com/en/US/docs/voice_ip_comm/cust_contact/contact_center/crs/express_8_5/configuration/guide/uccx851pug.pdf
I always do this as a matter of practice and I had a question concerning Java RMI ports. In the guide there is an ephemeral range TCP:32768-61000 that is used for Java RMI. Based on the context clues in the footnote this is an intra-cluster communication between processes running on CCX. This jives with ACLs I have built for previous versions.
The hang up I have is that Table 1 (page 6) of the guide shows that one of the remote devices is "Editor". I take this to mean CRS Editor, which can run on a desktop in the environment. I want to keep the ACL as trim as possible, so I don't want to open up the TCP ephemeral range unnecessarily. So, I guess my question is:
When that document refers to "Editor" do they mean that the CRS Editor is communicating using the referenced ports? Or is there a server-side process called Editor listening on those ports. The shift in how I apparently have to account for RMI is causing me to question.
Thanks in advance,
Bill

I followed the port guide, but am still having issues connecting to the editor from my workstation with my access-list in place.
When I remove the ACL the editor connects and I can do reactive debugging. The ACL breaks this.
Followed this
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cust_contact/contact_center/crs/express_9_02/configuration/guide/UCCX_BK_P89325D5_00_port-utilization-guide-uccx-902.pdf
Does anyone have a sample acl that works?

Key mapping question. (for mobile phones with PC-like keyboard)

For phones with mini keyboard (one button per one character, like a PC keyboard).
I'm trying to implement a form with few text boxes. The goal is to let user type the message like they're using a PC keyboard (unlike in traditional phones, where you need to press the 'numpad two' button three times in order to type the character 'C')
I've successfully implemented this functionality. But it's an ugly implementation because I use a switch-cases for each and EVERY keycodes.
Forexample:
char inputChar;
switch(keyCode)
case 97: input = 'A' break;
case 98: input = 'B' break;
// go on until every keys are covered, including the lower case letters. T_T
buffer.append(inputChar);
Yes I know that my programming skill is real crap >_<, so I try google for some good implementation method. But I always found only the detail about the traditional numpad implementations.
Ok, my real question is, can this keyboard implementation be done in a better way? The code should be able to look more beautiful than this, right?
Thank you. =)

I still don't get the problem here?
A textbox in a form will work just fine with those mini keyboards. You don't need to do anything for it..
Otherwise, this code can obviously be done better, a simple array where you just lookup your keycode will be much simpler and faster for instance.

Plug in updates for raw camera with photoshop cs4

Is there any way to upgrade the above mentioned plug in?

To what? Support for ACR is version specific. Refer to the charts below:
Camera Raw plug-in | Supported cameras
Camera Raw-compatible Adobe applications
If your camera isn't supported, you need to muddle through with the DNG converter until you can afford to upgrade. But you better hurry. The years is fast approachin its end and upgrade eligibility fades away...
Mylenium

Port Forwarding Question for IP Camera with MI424WR-GEN3

Similar Messages

Maybe you are looking for