PORT FORWARDING Step by step explanation needed

I need a very easy to follow step-by-step explanation as I can't seem to work this out.
I have broadband with a static IP address, it comes through my ethernet modem (D-Link ADSL Modem DSL-300T) this is connected to my Airport BaseStation (one with the modem port).
I have three computers connected wirelessly, one desktop, and two laptops that are frequently out of the office.
I want to set up my network so that I can use Apple Remote Desktop and FTP. I understand I need to open some ports on the basestation, but don't know exactly how or what ones. Also, do I need to set the macs up with DCHP with a manual address, or can I leave it at just DCHP?
Any help would be greatly appreciated.

Port Forwarding on an apple base station comes under the 'Port Mapping' section of the airport admin setup.
I found a howto that could help you .
http://www.roadstead.com/weblog/Tutorials/airport.html

Similar Messages

Port Forwarding, MI424WR

I'm not even sure I'll give enough information here, because I don't really know what I'm talking about. However, I've been working with a couple of "technical" people from my office.
Essentially, I'm trying to connect two devices (Yamaha Disklavier Pianos) over my FIOS connection (for a process called Remote Lesson) and need to utilize port forwarding. I've tried the instructions on the www.actiontec.com website (Basic Port Forwarding on the MI424WR Verion Fios Router), but have been unable to connect successfully.
Basically, here's the two things I need to do (cut and pasted from a technical document draft). Can someone please advise what might be going wrong?   I could also forward the entire "connection" document to someone who might want to take a look at it and get a clearer picture.
At any rate, here are steps 2 and 3 of the process we're trying to do:
2. Port Forwarding for Remote Lesson (WAN to LAN)
- Port 58092 is used in both TCP and UDP by default.
        - Note: You can choose any port unless it has already used.
- Please configure a system to forward the access of this port to Disklavier.
3. Release of the port to the Internet (LAN to WAN)
- If the access of port 58092 is filtered, please release this port in both TCP and UDP.
         Note: If your partner has configured another port number, please release that port in both TCP and UDP.
Port setting table
PORT FORWARDING (WAN TO LAN): IP Address (original LAN Address)
Port Number (origin)
Protocol: Both TCP and UDP
RELEASE OF THE PORT (LAN TO WAN): Port Number: Destination or all
   Protocol: Both TCP and UDP
Thanks for being patient with a "newbie" - I hope someone can help.

levesq56 wrote:
Essentially, I'm trying to connect two devices (Yamaha Disklavier Pianos) over my FIOS connection (for a process called Remote Lesson) and need to utilize port forwarding. I've tried the instructions on the www.actiontec.com website (Basic Port Forwarding on the MI424WR Verion Fios Router), but have been unable to connect successfully.
Thanks for being patient with a "newbie" - I hope someone can help.
If you're only trying to connect the 2 devices within your local lan you do not need to do anything with port forwarding. You would only need to add port forwarding rules if you are going to access the devices from remote sites.
The below addresses step 2 of your question.
Step 3 of your question is not needed as the actiontec does not block any port access from the LAN to the WAN
Step 2 allowing wan to lan access
If you are doing the latter then you would want to give the device fixed ip addresses, make sure they are out of the dhcp range of the actiontec router.
Then go to firewall setting
Select Port Forwarding tab
Select New Entry
add the IP address of the device in the Local Host field
Make sure Forward to Port is set as Same as incoming Port
Make sure Schedule is set as Always
Under protocols Select User defined
Make the service name whatever you want - e.g Piano
Select new server ports
Under protocols Select TCP
Under source port select single
enter 58092
Make sure destination port saya Any
Hit OK
Select New server ports again and repeat the last five steps for protocol UDP
then say OK
Say OK to the Edit port Forwarding rule
Now you should be able to access the device from the outside WAN

Cisco Ironport S160 Port forwarding

Hi,
We've got a device within the network which needs to send data out to a website on port 5009. We've setup the following to allow the traffic
- Identity with the interal IP as member and bypass the proxy (the device can only be configured with the Proxy IP and port, no logins)
- Added Port 5009 n HTTP Ports to Proxy
- Added the destination IP n L4 Traffic allow list
We are still not able to route the traffic.
We then tried to get the traffic coming in the other way. We've asked the ISP to put in a port forwarding to forward traffic on Port 5019 to the device. This is also not working. We can get to the device on the internal Port without any issues. The question does the IronPort need to be configured to allow the traffic coming in? We dont have any other incoming port forwarded traffic.

Hello,
I will need a quick explanation on how your environment is laid out for your Web Content Appliance.
1. Is your proxy transparent or explicitly proxied? Do you have multiple proxies that you are load balancing?
2. If it is explicit, do you use a PAC file or is the proxy configured in the network configuration?
3. If it is transparent, what do you use to redirect traffic? Is it wccp or L4 redirection? What kind of device are you using to redirect traffic? ASA, Catalyst, Nexus, something else?
4. Is there any third party devices being used between the proxy and the clients or between the proxy and the outside world?
5. What are your authentication requirements? How are you authenticating them (NTLMSSP, TUI, or Basic)?
Thank you for answering these questions.
Christian Rahl
Customer Support Engineer
Cisco Web Content Security Appliance
Cisco Technical Assistance Center RTP

RV082 port forwarding limited to 30 entries ?

Hello,
we use RV082 as main gateway and need to open/forward around 50 ports to inside. But during setting of the rules I got an error message "The max of Port Range Forwarding is 30 entries. You can't add any more.".
In the online help is explicitely said "4. Click the Add to List button, and configure as many entries as you would like."
How can we setup more than 30 port forwarding rules ?
If it is this a sotfware bug, can this be corrected ?
Regards,
Petr Svoboda

Petr, I agree with tekliu. I use the UPnP rules with UPnP disabled for all of my port forwarding, unless a range is needed. They should not cause any more exposure than regular Forwarding rules, and if you use port translation they will reduce your exposure.
The only differences:
Forwarding allows port ranges
Forwarding has a "Port Triggering" section
UPnP allows port translation (because it's only single port at a time, not a range)
UPnP has unlimited entries

PAPI Webservice documentation and Step by step explanation

Where do I get PAPI Webservice documentation and Step by step explanation?
Is there any book or pdf file which contains lots of examples? if so where I can get it?

Here is the location of a step-by-step explanation on how to use PAPI Web Service (PAPI-WS) to create a work item instance and then run the instance inside an activity in a process running on Oracle BPM Studio.
http://www.4shared.com/file/128256802/f20abc7a/PAPI-WS_for_Oracle_BPM_Studio.html
Be sure to use the project that is in the zip file for this example.
If you need an example of how to use PAPI-WS on Oracle BPM Enterprise, go to this thread: PAPI Web Service (PAPI-WS) Example for Oracle BPM Enterprise Standalone
If you need a step-by-step example of how to use PAPI (the Java API) go to this thread: Creating a new work item instance in a process using PAPI
The Oracle BPM 10g docs are on this page: http://download.oracle.com/docs/cd/E13154_01/bpm/docs65/index.html. There is a section that might help regarding PAPI.
Hope this helps,
Dan

Step-by-Step Help Needed for Deploying Some Adobe Software

We are a K-12 educational institution. I am currently working at setting up a computer lab with about 16 MacMini computers.
I'm VERY new to the realm of servers, deployment, using terminal, etc.
I've done lots of research to make it to where I am, but just can't wrap my head around what needs done next with the Adobe products.
I am using Server OSX (v3) and DeployStudio (v 1.6.3) to try and manage the computers.
Both my server and clients are running Mavericks 10.9.
I deployed my core images successfully and would like to now send Adobe products only the computers I choose since I have limited licenses.
We have volume licenses of Adobe InDesign CS6 and Photoshop Elements 12 that we would like to deploy.
I have been referencing the following sites, but just can't seem to wrap my head around the EXACT steps that need to be taken.
http://blogs.adobe.com/oobe/2010/10/adobe-provisioning-toolkit-enterprise-edition.html
http://helpx.adobe.com/creative-cloud/packager/provisioning-toolkit-enterprise.html
http://helpx.adobe.com/photoshop-elements/kb/silent-install-instructions-photoshop-element s2.html
http://forums.adobe.com/message/5781663
For Adobe InDesign CS6 - I've done the following:
Created an "Installation Package" using Adobe Application Manager Enterprise Edition (AAMEE v6.2.112.0) using the following instructions.
http://wwwimages.adobe.com/www.adobe.com/content/dam/Adobe/en/devnet/creativesuite/pdfs/Ad obeApplicationManagerEnterpriseEditionDeploymentGuide_v_3_1.pdf
If I log into the client computer, put the package ON the client computer, and run it...it takes me through the install and works wonderfully.It's not automated like I wanted/thought I set it up to do. I have to click through the steps of the installer.
If I try to deploy it using the "Package install" Workflow in DeployStudio...it loads it during the workflow, then skips through it, acts like it installed it, but it isn't actually installed.Is there a setting that I need to possibly change somewhere?
For Adobe Photoshop Elements 12 - I'm a bit lost and mostly just have questions:
I know that I can't use AAMEE and need to use APTEE (Adobe Provisioning Toolkit Enterprise Edition).
How do I deploy the software? Create my own Package using PackageMaker?
Which computer do I run APTEE on? All the instructions I can find just say, "do this" - but don't specify where.
Do I have to open terminal and run the commands on each client computer AFTER installing PE12?
OR
Do I run the commands BEFORE deployment on my package stored on my server that is ready for deployment?
It really comes down to me just not 100% understanding how APTEE works.
I hope that pertrays my dilemma. I've tried to explain best I can. If you have any questions - let me know!
Thanks in advance for any insight you can give!

We are a K-12 educational institution. I am currently working at setting up a computer lab with about 16 MacMini computers.
I'm VERY new to the realm of servers, deployment, using terminal, etc.
I've done lots of research to make it to where I am, but just can't wrap my head around what needs done next with the Adobe products.
I am using Server OSX (v3) and DeployStudio (v 1.6.3) to try and manage the computers.
Both my server and clients are running Mavericks 10.9.
I deployed my core images successfully and would like to now send Adobe products only the computers I choose since I have limited licenses.
We have volume licenses of Adobe InDesign CS6 and Photoshop Elements 12 that we would like to deploy.
I have been referencing the following sites, but just can't seem to wrap my head around the EXACT steps that need to be taken.
http://blogs.adobe.com/oobe/2010/10/adobe-provisioning-toolkit-enterprise-edition.html
http://helpx.adobe.com/creative-cloud/packager/provisioning-toolkit-enterprise.html
http://helpx.adobe.com/photoshop-elements/kb/silent-install-instructions-photoshop-element s2.html
http://forums.adobe.com/message/5781663
For Adobe InDesign CS6 - I've done the following:
Created an "Installation Package" using Adobe Application Manager Enterprise Edition (AAMEE v6.2.112.0) using the following instructions.
http://wwwimages.adobe.com/www.adobe.com/content/dam/Adobe/en/devnet/creativesuite/pdfs/Ad obeApplicationManagerEnterpriseEditionDeploymentGuide_v_3_1.pdf
If I log into the client computer, put the package ON the client computer, and run it...it takes me through the install and works wonderfully.It's not automated like I wanted/thought I set it up to do. I have to click through the steps of the installer.
If I try to deploy it using the "Package install" Workflow in DeployStudio...it loads it during the workflow, then skips through it, acts like it installed it, but it isn't actually installed.Is there a setting that I need to possibly change somewhere?
For Adobe Photoshop Elements 12 - I'm a bit lost and mostly just have questions:
I know that I can't use AAMEE and need to use APTEE (Adobe Provisioning Toolkit Enterprise Edition).
How do I deploy the software? Create my own Package using PackageMaker?
Which computer do I run APTEE on? All the instructions I can find just say, "do this" - but don't specify where.
Do I have to open terminal and run the commands on each client computer AFTER installing PE12?
OR
Do I run the commands BEFORE deployment on my package stored on my server that is ready for deployment?
It really comes down to me just not 100% understanding how APTEE works.
I hope that pertrays my dilemma. I've tried to explain best I can. If you have any questions - let me know!
Thanks in advance for any insight you can give!

Application And Gaming / Port Forwarding || HELP NEEDED || Can Only Access Via LAN

Hi.
I have just bought a Wireless Router, Model Number: WGKPC354G-UK. With the intention of setting up a small server. This server will run from my PC (directly wired into router), running a game called "Counter Strike" - I had to download a dedicated-server tool for this and i successfuly installed this and followed the tutorial to set it all up..
So I thought i had done it, but I could only access my server with my internal IP 192.168.1.64 (LAN).
I then found out that i needed to "Port-Forward" I followed a tutorial on www.portforward.com - This showed me how to open the ports, and which ones to open.
I did all this and i still encounter the same problem !
So i then opened all my router ports "DNZ" and it still doesnt work !!!
Any help will be greatly aprreciated !
PS. Below Are The Required Ports.
http://portforward.com/english/routers/port_forwarding/Linksys/WAG354G/Counter_Strike.htm

Keep in mind your ISP could be blocking the ports needed. DMZ almost ALWAYS works and if it doesnt, most likely your ISP blocks the ports.
another test is to make sure you can connect to the game server from another CS machine on the inside of your network. If this works, that means your server is up and running properly and its probably your ISP blocking certain ports needed for the CS Server.
You should also check you have the Windows firewall disabled, and any other software firewall on your server disabled.

I need to transfer settings from my Macbook to a new Macbook pro. what are the steps I need to follow?

I need to transfer the settings (mail, safari, etc.) from my Macbook to a new Macbook pro. what are the steps I need to follow?

Time Machine will sort that out, you got an external HD ?

How do I convert from PDF to Word step by step instructions needed..am practically computer illiterate

How do I convert from PDF to Word step by step instructions needed..am practically computer illiterate@

Ok, fine. That isn't Acrobat, and that's why our instructions weren't much use. (But it's worth saying "I didn't have that option" rather than "it's not converting", we could end up wasting a lot of your time with the wrong stuff!)
Anyway, the free Adobe Reader can't do this conversion without a subscription called either ExportPDF or PDF Pack. You may have had one in the past. Are you still paying for one?

Help needed to do port forwarding in ipfw...

For the last weeks I have been working to get the new open-source content management system Alfresco working. It is a pure Java web application that runs under Tomcat. There is official support for Mac OS X but only Windows and Linux gets true installer binaries with guides and everything.
The unique thing about this platform is that it has a built in Java-based CIFS/SMB-server to expose the content not only in web browser but as a mounted volume as well. However, it turned out more than difficult to get that working in my Mac OS X Server 10.4.9 running on an XServe G5 2.0Ghz.
I can run the startup script for the Tomcat as root on my laptop running Mac OS X 10.4.9 and then the CIFS-server can use standard ports like 137, 138, 139 and 445. Finder can mount that as a volume called Alfresco. However, I do not want to run it as root because of several other issues related to X11. There is a note in the installation text that if running the script not as root but as admin or a designated Alfresco user requires port forwarding. That means setting up firewall rules to forward requests from the standard CIFS TCP ports 139/445 to the non-privileged ports the Alfresco CIFS server is listening on (which are 1137,1138,1139 and 1145).
I have understood that this is not possible through the Server Admin GUI-app but needs to be done either in the terminal or by using an app like WaterRoof. I guess also Apple´s server tools are famous for overwriting config files made by a "third-party" app. However, I can't make it work and ipfw syntax still looks very confusing to me. Any ideas of what I need to do in order to have this port forwarding to work.
I have tried something like this so far:
# ! /bin/sh
echo "Setup CIFS Port Forwarding ..."
sysctl -w net.inet.ip.fw.enable=1
sysctl -w net.inet.ip.forwarding=1
sysctl -w net.inet.ip.fw.verbose=1
sysctl -w net.inet.ip.fw.debug=0
#ipfw add 100 count log ip from any to any
ipfw add 200 allow ip from any to any via lo0
# Forward native SMB and NetBIOS sessions to non-privileged ports
ipfw add 300 fwd 192.168.1.2,1445 tcp from any to any dst-port 445 in
ipfw add 400 fwd 192.168.1.2,1139 tcp from any to any dst-port 139 in
# Forward NetBIOS datagrams to non-privileged ports
ipfw add 500 fwd 192.168.1.2,1137 udp from any to any dst-port 137 in
ipfw add 600 fwd 192.168.1.2,1138 udp from any to any dst-port 138 in
Windows filesharing i Mac OS X Server is turned off and there are firewall rules to allow traffic on the designated ports.
http://www.alfresco.com
Any hints would be very helpful!
XServe G5 Mac OS X (10.4.9)

Ok, thanks for the tip. Had a look at that page and it was only about NAT which is not what I am looking for. I have a server with public IP where I need to forward from one port to another on the same IP. However, I find the information about how to configure IPFW rather limited so I wanted to know if the rules in the first post look right and what pitfalls there are when using the GUI-based server admin tools from Apple

Two-step verification needs one SMS capable phone number. As I am a Bangladeshi how can I send phone number.pl help.

Two-step verification needs one SMS capable phone number. Bangladesh is not listed country. How can I receive message my phone.

2-step verification is not available in Bangladesh as yet.

HT1386 Switching from a pc to a Mac. What steps are needed to get my iPhone and iPad to work with my new Mac?

What steps are needed when upgrading from a pc to a Mac?

Copy everything from your old computer to your new one.

I bought the pkg. of Photoshop & Premiere Elements 10 in 2012. I now want to update to Premiere Elements 13 without updating Photoshop. Can I do this? Will you please tell me the steps I need to take?

I purchased Photoshop and Premiere Elements 10 as a package in 2012. I now want to update the Premiere to the 13 edition, without updating Photoshop. Can I do this? Will you please tell me the steps I need to take?

Just buy version Premiere Elements 13.
Even if you don't get the "upgrade" price, you can probably find it for about that cost on sites like Amazon.com.
You can keep Photo Elements 13 if you'd like. The only downside is that Premiere Elements 13 and Photo Elements 10 won't share the same Organizer catalog. Otherwise, they'll get along just fine.

I have a full Creative Cloud Subscription, but I only use Photoshop and Bridge. I want to change to a less expensive subscription but it is not clear what steps I need to do to make this happen. Do you have a simple step by step guide? Seems that there is

I have a full Creative Cloud Subscription, but I only use Photoshop and Bridge. I want to change to a less expensive subscription but it is not clear what steps I need to do to make this happen. Do you have a simple step by step guide? Seems that there is lots of help to upgrade but not down grade.

FIRST check with Adobe to find out if you may cancel what you have without a fee
Adobe contact information - http://helpx.adobe.com/contact.html
-Select your product and what you need help with
-Click on the blue box "Still need help? Contact us"
Then cancel what you have
-cancel http://helpx.adobe.com/x-productkb/policy-pricing/return-cancel-or-change-order.html
-or http://helpx.adobe.com/x-productkb/policy-pricing/cancel-membership-subscription.html
-or by telephone http://helpx.adobe.com/x-productkb/global/phone-support-orders.html
And finally buy a new subscription
Cloud Plans https://creative.adobe.com/plans
-Special Photography Plan includes Photoshop & Lightroom & Bridge & Mobile Lightroom
-Special Photography Plan includes 2Gig of Cloud storage (not the 20Gig of the full plan)

HT1296 Hi i am trying to update my ipad 2 it is on version 4 and has not had an update since and i donot have the option to update on my device what is the next step i need to take?

Hi i am trying to update my ipad 2 it is on version 4 and has not had an update since and i donot have the option to update on my device what is the next step i need to take?

See the chart below to determine whether you can upgrade your device and what you can upgrade to. If you do not have a Software Update option present on your iDevice, then you are trying to upgrade to iOS 5 or higher. You will have to connect your device to your computer and open iTunes in order to upgrade.
IPhone, iPod Touch, and iPad iOS Compatibility Chart
     Device                                       iOS Verson
iPhone 1                                      iOS 3.1.3
iPhone 3G                                   iOS 4.2.1
iPhone 3GS                                 iOS 6.1.x
iPhone 4                                      iOS 7.0.x
iPhone 4S                                    iOS 7.0.x
iPhone 5                                      iOS 7.0.x
iPhone 5c                                     iOS 7.0.x
iPhone 5s                                     iOS 7.0.x
iPod Touch 1                               iOS 3.1.3
iPod Touch 2                               iOS 4.2.1
iPod Touch 3                               iOS 5.1.1
iPod Touch 4                               iOS 6.1.x
iPod Touch 5                               iOS 7.0.x
iPad 1                                          iOS 5.1.1
iPad 2                                          iOS 7.0.x
iPad 3                                          iOS 7.0.x
iPad 4                                          iOS 7.0.x
iPad Mini                                      iOS 7.0.x
iPad Air                                        iOS 7.0.x
=====================================
Select the method most appropriate for your situation.
Upgrading iOS
   1. How to update your iPhone, iPad, or iPod Touch
   2. iPhone Support
   3. iPod Touch Support
   4. iPad Support
     a. Updating Your iOS from iOS 5
          Tap Settings > General > Software Update
     If an update is available there will be an active Update button. If you are current,
     then you will see a gray screen with a message saying your are up to date.
     b. If you are still using iOS 4 — Updating your device to iOS 5 or later.
     c. Resolving update problems
        1. iOS - Unable to update or restore
        2. iOS- Resolving update and restore alert messages

PORT FORWARDING Step by step explanation needed

Similar Messages

Maybe you are looking for