Port mapping not working

i have several devices that i have tried setting up port forwarding for, but no matter what i do the ports always report back as closed when i use various websites to check the state of them and i can not get access to my devices. i have a virgin media superhub in modem mode and the time capsule as my router with an airport express as a range extender. i have set the devices in dhcp reservations and forwarded different ports to each one, but after i click update and the router comes back online i check the ports and they are still closed. does anyone have any ideas?
thanks

What OS and what airport utility are you running?
When you go back to the TC are the ports saved as you expected?
I would not worry if a web site check does not find the port open.. but yes, the test is does it work, with what you expect in terms of application.
Give us screenshots of the setup.. that is the huge advantage of this forum.. easy to take and post screen shots and we can then get an idea of what is happening.

Similar Messages

  • Port mapping not working with 7.5.1

    I am having trouble getting Port mapping working with the new 7.5.1 firmware. Port mapping is not working. Port mapping was working fine before update, now all attempts to connect from WAN on ports are rejected. Tested with: telnet <wan-ip> <port>
    I have removed and re-added all port mapping entries - no luck. Power cycled several times - no luck.
    Other info:
    I have an: Airport Extreme (Simultaneous Dual-Band II) running Version: 7.5.1.
    It is setup to "Allow this network to be extended"
    Network is being extended with an Airport Express with 802.11n running 7.4.2

    yeah. I noticed the same thing. now the splash screen comes on without the flashing green squares and just hangs. i tried unintalling and then reinstalling and still no go. kind of annoying but they will probably come out with an update pretty soon

  • Port Mapping Not Working...at all!

    I've been tyring to get port mapping working correctly since I got the AEBS a few months ago. I've scoured all over these forums and the entire internet and found not a single suitable answer. I have my macbook pro setup up wirelessly all works fine except port mapping.
    My macbook is setup up manually with a static IP of 10.0.1.2 and lets say i want to map the port 41952. In the port mapping setup assistant on the base station I leave the service setting on "choose a service", public UDP 41952, public TCP 41952, IP address 10.0.1.2, private UDP and TCP 41952. Then I update and router resets... then I use the network utility to check the ports and they're not showing as open, I've used various internet websites as well and the port comes up closed. What on earth am I not doing? Someone please help! or let me know if you are having the problem as well.
    Thank you for ANY help.

    You are not performing a valid test.
    No, Cable modem plugged into WAN port, the computer i'm trying to open ports on is using a wifi connection with the aebs.
    You can not test the AEBS to see if the ports are open from the LAN side of the AEBS. You must be on the internet (WAN) side of the AEBS to test to see if the port is open on the AEBS.
    ...the computer i'm trying to open ports on is using a wifi connection with the aebs.
    You aren't opening ports on the computer, you are opening ports on the AEBS.

  • Airport NAT/Port Mapping not working :(

    Hey kids,
    I've recently scored myself a time capsule and I'm totally loving the time machine functionality, but the airport extreme part is causing me a little bit of grief!
    I commonly use applications like transmission and play online games etc, not to mention usually have personal web sharing enabled for work etc.
    Since i've installed the extreme i've had loads of issues getting ports to forward outside the local network!
    The old router I had (a belkin one) did all this stuff with no hitch at all.
    As an example, if I launch say, transmission my port status is apparently "stealth" even though i've got the automatic setup enabled. If I load the airport utility and manually forward the port no difference is made.
    Additionally, if I enable web sharing and choose the web sharing service from the airport utility drop down the same stuff happens... port 80 isn't made available from outside the network
    Has anyone else run into these issues?

    Really frustrated with this problem. Does anybody at least know how to debug the problem ?

  • USB ports does not work

    Hi I have problems with not working USB ports. It used to work. I downloaded actual drivers at msi.com for my gaming notebook GX 60 Destroyer and now my USB ports does not work. What should I do?

    What driver have you updated?
    Try to do an EC firmware reset by removing the battery and the AC adapter then put the battery back with AC adapter attached.
    Same questions like Pegasus asked, does all ports not working? which one exactly? What OS are you using?
    Have you done any changes to the system? (for example: self-install OS or changing OS)

  • I plugged in my ipod and now i get the error message: Because a USB device was drawing too much power from your computer, one or more of your USB devices have been disabled" - i have a MAcBook pro and now my USB ports do not work - can anyone help me ???

    i plugged in my ipod and now i get the error message: Because a USB device was drawing too much power from your computer, one or more of your USB devices have been disabled" - i have a MAcBook pro and now my USB ports do not work - can anyone help me ???

    Sometimes you have to reset the SMC two or three times for it to work, don't know why. I've seen that error message before and 100% of the time it was fixed with an SMC reset. I suppose it's possible that your keyboard or mouse IS drawing too much power, do you have access to another you could try?

  • Audio output and left USB port is not working!

    Hi! I have MacBook Air 13" late 2010, Audio output and left USB port is not working!
    What happened?
    Part No.: Z0JH000TE RS

    If the left USB port doesnt work with an external mouse its seems to be a hardware malfunction of this USB port.
    The newest BIOS is already installed?
    Have you removed all USB ports from device manager and restarted your notebook?
    If you have already tried this, contact an authorized service provider. The guys can try to fix this issue and it should be covered by warranty, if you still have warranty on this notebook. :)

  • MY EXTERNAL SPEAKER PORT IS NOT WORKING for hp envy

     MY EXTERNAL SPEAKER PORT IS NOT WORKING .WHEN I CONNECTED TO A EXTERNAL SPEAKER ,THERE WERE NO SOUND AUDIBLE.SO WHEN I DISCONNECTED THE CABLE FROM PORT,I WAS ABLE TO HEAR WITH THE IN BUILT SPEAKERS.EXTERNAL SPEAKER IS I GOOD CONDITION.I CHEKED WITH MY HEAD SET ALSO.IT WAS NOT AUDIBLE.MY LAP IS HP ENVY .KINDLY HELP

    Hi ano87, welcome to the HP Forums. What is the model or product number? What version of Windows is installed?
    Guide to finding your product number
    Which Windows operating system am I running?
    TwoPointOh
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

  • After installation, the mobo LAN port is not working? urgent, help ple

    I just installed archlinux on my new i7 860 Asus p7p55d-e Deluxe build, but after the installation the LAN port is not working anymore. Before this, this Lan port works perfect in windows as well as in the arch installation. But after the installation, the led is orange and is blinking slowly, windows complains that the cable is not properly plugged, and even arch installation can't pull DHCP from it also.
    Luckily, the mobo has another lan port, so I have to plug the cable out and to the second port, but I couldn't seem to be able to find anyway to enable the first Lan port anymore?
    Have you seen anything like this, what possibly is the reason?
    Thanks, any help will be appreciated.

    heleos, thanks for the reply, the first thing I check is BIOS. There is definitely nothing wrong with that, since I loaded the default one.
    It is really strange, it seems no matter what I do, the 1st port which used to work, simple doesn't work, but the second one works fine.
    But after some poking around with the "ethtool", it starts to work again. I have no idea what cause the disfunction and what magically heal it again.
    Now I am really curious.
    Last edited by mark.altern (2010-04-18 09:52:09)

  • T420 USB Ports do not work after installing XP

    Hello my office has  been using Lenovo's for some time now but we recently purchased a T420 and installed Windows XP SP3 on it.  The issue we are having is that the uSB ports do not work.  I have tried every driver I can find but still no luck, can anyone help?

    hey chris0277,
    could you check in Device Manager and see if there is any ? or ! symbol on the USB area.
    If there is, i do recommend uninstalling the drivers from it and then visit http://support.lenovo.com and update your unit
    WW Social Media
    Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
    Follow @LenovoForums on Twitter!
    Have you checked out the Community Knowledgebase yet?!
    How to send a private message? --> Check out this article.

  • PavillionG​7-2315nr windows 7(64 bit) USB serial control or usb ports are not working. Please help!

    Hi I downgraded the laptop from windows 8 to windows 7 64 bit. Two of my USB ports are not working and cant find the right drivers for it. Can you please direct me, where I can download and update the drivers? Thanks in advance.
    Shawe

    Hi:
    Download and instal both of these drivers and reboot.
    http://h20565.www2.hp.com/hpsc/swd/public/detail?s​p4ts.oid=5229463&swItemId=ob_125616_1&swEnvOid=405​...
    http://h20565.www2.hp.com/hpsc/swd/public/detail?s​p4ts.oid=5229463&swItemId=ob_123787_1&swEnvOid=405​...

  • My Air port is not working the wifi - just an amber light blinking. What's going on ?

    My air port is not working the wifi - just an amber light blinking. What's going on ?

    Sorry it is just not enough info to be able to figure it out.
    Do a full factory reset and start over.. that is the best way out of the hole.
    Using ethernet is far far superior to using wireless at least for setup.
    Using iOS device with airport utility is better than using wireless via a Mac with airport utility if you have MBA or MBPr.. but it is still better to buy a usb or thunderbolt to ethernet dongle so you have actual real connection and not a vapourous one.

  • IMac firewire port is not working

    iMac firewire port is not working
    Hi everybody, Happy New Year.
    I am a 72 years old semi-newbie in video editing, because Iedit only 1 or may be 2 movies a year since 2007 and I have only very little computer knowledge. 
    I received a new 27” iMac as a birthday gift 14 months ago.  About 10 months ago, with help, I successfully use the Migration Assistant to transfer some datas from my old power G4 to the iMac including two Final Cut Express projects.  I had one project successfully done; burned to DVD and I save it with Print To Video. Last week, I have my second project done, I burned the sequences into DVD but unable to do a Print To Videodue to the iMac is not communicating with my Sony camcorders DCR VX1000, this is the same camcorder I used on the last job which was working a couple of months ago.As a result, I try to switch the Easy Setup with different Format and different Use; I refresh the Canvas window; I did a Mix down; move the Screen Saver to NEVER as well as the Energy Saver set to NEVER SLEEP.  I also trashed the preferences (plist) folders; run the Utility repair, I replaced the firewire cable (4 pines – 9 pines 800), but nothing work.  Up to this point, I think that there is no signal from the firewire port to the camcorder because I understand when the sequences is ready, the firewire is connected between the computer and the recording camcorder, the Print to Video is activated, then the word DV- IN should be seen on the recording deck screen. This time, I don’tread such words on the recording screen. Therefore, I think there’s no out going signal from the iMac to the recording camcorder and the iMac is not receiving signal from the recording camcorder. At this point, I try to connect my iMac to the power G4 to see if I can do some data transfer. Follow the procedures, I hook up the data transfer cable between the G4 and the iMac, I can the fireswire icon moving on the G4 screen but no indication on the iMac screen (there should be some indications in the source bar), this shows me the iMac did not recognize the G4 which worked on previous data transfer.  It looks to me the firewire port on my iMac is dead.  What has gone wrong? Could I accidentally disabled the firewire port by some magic keystroke? (i.e. accidentally fat finger some thing to make it stop working?  Oh, by the way, during the playing around, went to the Final Cut tool bar, I click the View >Video Out > Digital Cinema Desktop Preview – Main, the result was a  black screen and the esc key was my rescuer - LUCKY LUCKY! Are there any other trouble-shooting techniques to apply before bringing to shop?  Please help!
    Sorry for such a long statement, forgive me for unable to make it shorter.  Thank you for your patience. Thanks to all the folks in this board for being so helpful.
    p.s.

    Not sounding good.
    If the system Profiler does not see it then there is a basic communication problem between camera and the Mac.
    I'm thinking the Firewire port is the culprit as some 800 ports were faulty.
    I'd suggest taking the Mac, cable and camera to your nearest Authorized Apple Service Centre and get them to diagnose the issue. eg. let them try to connect the two devices.
    Right (control)click the Sequence icon in the Browser and select Item Properties, do the same for a clip.
    You can also post screen shots for the Properties.
    Al

  • Alternate Access Mapping not working for Zone : Intranet

    One of our client want to set Alternate Access Mappint (intranet) with url "intranet.theirDomain.com" with local IP address.
    is it possible?
    subsequest to my previous question (
    http://social.technet.microsoft.com/Forums/sharepoint/en-US/3f39711e-301a-40e8-aa7a-855fa2c268b1/alternate-access-mapping-not-working?forum=sharepointadmin )
    I want to ask one more question
    Can we configure "intranet.theirDomain.com" with local IP address for any other zone?
    or
    If there is ".com" within the url then it can't be configured for InTRAnet?
    Thanks
    S H A J A N

    The names for the zones don't matter. You could use the 'extranet' zone for another intranet name if you wanted, the names are just to make it a bit more friendly for beginners.
    What you describe sounds routine, you create a web application with a name, then use an AAM to allow users to access it with a more friendly name. Frequently you end up creating
    http://intranet.domain.com and
    http://intranet as an AAM, or vice versa.
    You can use .com for an intranet site, you would need to add the site as an A Host record in your DNS server so that traffic is sent to your internal server rather than out into the wider world.

  • Value mapping not working properly

    Hi All,
    I am using value mapping twice in same mapping program. But only 1 field is coming with value and other is taking same value from source payload, can you please tell me what can be issue here?
    Value mapping 1 -
    Context - http://sap.com/xi/XI
    SenderParty- SenderSchema
    ReceiverParty- ReceiverSchema
    Value Mapping table in ID -
    Value mapping at field 2 -
    Context - http://sap.com/xi/XI
    SenderParty1- SenderSchema1
    ReceiverParty2- ReceiverSchema2
    Value Mapping table in ID -
    Source payload -
    <?xml version="1.0" encoding="UTF-8"?>
    <ns0:MT_VM_Send xmlns:ns0="http://xyz.com/Rashmi_CollectPatternDemo">
       <Record>
          <Emp_ID>123</Emp_ID>
          <Name>rash</Name>
          <Surname>sumit</Surname>
          <Gender>Male</Gender>
         <Grade>E2</Grade>
      </Record>
    </ns0:MT_VM_Send>
    Target Payload -
    <?xml version="1.0" encoding="UTF-8"?>
    <ns0:MT_VM_Receiver xmlns:ns0="http://xyz.com/Rashmi_CollectPatternDemo">
    <Record>
    <Emp_ID>123</Emp_ID>
    <Full_Name>rash sumit</Full_Name>
    <Designation>E2</Designation>
    <Gender>M</Gender>
    <Travel_Mode>Train</Travel_Mode>
    </Record>
    </ns0:MT_VM_Receiver>
    Here travel_mode is coming perfect, but designation is same as defined in source payload. Why here Value mapping not working???
    Thanks & regards,
    Rashmi Joshi

    Hi Rashmi,
    The problem would either be in cache update or your mapping. Please provide the sceenshot of mapping (after clicking the value mapping function).
    you can also choose the option to throw error in value mapping function, so it will throw error when value not found.
    regards,
    Harish

Maybe you are looking for