Port Mapping / port forwarding - help please...again...

Hi,
I am trying to use port forwarding/port mapping but after numerous failures to access my computer from an Internat connection, I am seeking advice or guidance.
I have a 2011 Apple Time Capsule, and under the Advanced tab on Airport utilities, Port mapping I have chosen +
it then comes up with a box in which I have entered the following:
Service - drop down menu (number of options...but have been advised on other threads to leave as is)
It then has 5 boxes:
Public UDP port(s) - 9080
Public TCP ports(s) - 9080
Private IP adress - 10.0.1.x
Private UDP Port(s) - 9080
Private TCP Port(s) -9080
note I have enabled NAT port mapping protocall. My ISP has advised that I cant use port 80 for some reason...but all others should be ok
note also the 10.0.1.x is a static address i have assigned to teh camera.
I have a dns provider, and when I use the URL on my LAN - I can access the camera....but as soon as I tryu to access via the WAN - it is unable to reach the server.
Other points - the TC is in normal mode (i.e. not Bridge)
Does anyone have any idea if I have set port mapping up correctly; any way i can test, any ideas how i can fix this??
I have tried this on a number of forums thus far - but no success to date.
Welcome all and any help!!!

LaPastenague wrote:
Have you reset the camera web page to use 9080?
i have checked again and in teh advances settings of my camera - it asks for HTTP port, HTTPS port, and for Nata Traversal it asks for an alternative HTTP port.   I have entered 9080 against all of these.
The TC is in normal mode ie as a router.. what modem do you have in front of it? Is it in bridge? Does the TC get the public IP or does the modem route the address as well? You will have no success via double NAT.
not sure what brand the modem is - but i can confirm it is set up as a modem only with both the router and wireless functions turned off.
The Modem is not in Bridge mode - neither is my ATC. The ATC gets the public IP address via the adsl modem. so double NAT should not be an issue
When you say you can access the camera using URL on lan, is that using the new port 9080? Please give explicitly what address you use.. (you can hide the full public address) and port.. and AFAIK this should NOT work as the TC would have to handle NAT Loopback which would amaze me if it does. According to all the info around the web the TC has no NAT Loopback and therefore should not be able to handle the address. I need to know therefore the exact address you use
this is actually using the url that my dns provider provides to me as i do not have a static ip address.   albeit this appears temperamental as to when it works sometimes from my LAN. after which it requests user name and password and I can then see the live stream.
one problem I have just noted is that when checking teh DNS setup - it still appears to default to port 80 which my isp has advised i can not use) so i am checking with teh dns provider how i change this.
The good news is port mapping must work on my ATC, as I have just set up my slingbox using their automatic port mapping assistant and it seemed to set up with no issues...i have also just confirmed that the stream can be viewed on the internet.

Similar Messages

Port forwarding help please

Hi All,
I am looking to forward my airport extreme base station to port 57331. No matter what I trying I can't get Playon software working. It is running through parallels since it is a windows only program that allows netflix to be streamed to a driod phone. Can someone please provide a step by step process to port forward? Thank you so much in advance.
Scott

Can someone please provide a step by step process to port forward?
Scott,
The following is the basic steps to configure port mapping/forwarding on the 802.11n AirPort Extreme Base Station (AEBSn):
To setup port mapping on an AEBSn, either connect to the AEBSn's wireless network or temporarily connect directly, using an Ethernet cable, to one of the LAN port of the AEBSn, and then use the AirPort Utility, in Manual Setup, to make these settings:
1. Reserve a DHCP-provided IP address for the host device.
o AirPort Utility > Select the AEBSn > Manual Setup > Internet > DHCP tab
o On the DHCP tab, click the "+" (Add) button to enter DHCP Reservations.
o Description: <enter the desired description of the host device>
o Reserve address by: MAC Address
o Click Continue.
o MAC Address: <enter the MAC (what Apple calls Ethernet ID if you are using wired or AirPort ID if wireless) hardware address of the host computer>
o IPv4 Address: <enter the desired IP address>
o Click Done.
2. Setup Port Mapping on the AEBSn.
Advanced > Port Mapping tab
o Click the "+" (Add) button
o Service: <leave at the default setting>
o Public UDP Port(s): 57331
o Public TCP Port(s): 57331
o Private IP Address: <enter the reserved DHCP IP address here>
o Private UDP Port(s): 57331
o Private TCP Port(s): 57331
o Click "Continue"

Firewire Port not working, URGENT help please¡¡¡

Hello People, i´ve just got a new Mac Mini last week, and i´ve been trying to get my Alesis MasterControl audio interface, and is just a complete mess.
This happened right after i´ve upgraded to 10.8.3 so i don´t know, the weird thing is that if i connect my old iBook to the Mac Mini the FW800 port works, but everytime i connect the audio interface, nothing happens, also the drivers from alesis, are up to date. i first thought about the port of the Mixer went bad, but it has 2 and non of them works, also thought about the cable but the same cable works when i connect my iBook, and the mixer is not bus powered, it has it´s own power supply.
Needless to say i´ve already done the usual reset PRAM, turn of the Mac unplugged for 30 hour to reset the bus. etc.
This is the usual firewire only system log that i get:
31/03/13 08:01:20.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in now active, GUID 003ee1fffe88dc6a; max speed s800.
31/03/13 08:01:30.000 kernel[0]: Alesis Firewire - 3.5.6.11675 (x86_64) Aug 16 2011 01:20:23
31/03/13 11:33:23.529 system_profiler[528]: SPFWR ERROR: FireWire bus may be unstable. Other FireWire devices may be present.
31/03/13 11:35:43.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in: no valid selfIDs for more than 3 minutes after bus reset.
31/03/13 11:38:55.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in: no valid selfIDs for more than 3 minutes after bus reset.
31/03/13 11:42:08.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in: no valid selfIDs for more than 3 minutes after bus reset.
31/03/13 11:44:39.124 CleanMyMacHelperTool[583]: Mounted devices (
    "/Volumes/AlesisFirewire-3.5.3.8671"
31/03/13 11:44:39.146 CleanMyMacHelperTool[583]: Wont clean /Volumes/AlesisFirewire-3.5.3.8671 because disk image
31/03/13 11:44:39.148 CleanMyMacHelperTool[583]: Mounted devices (
    "/Volumes/AlesisFirewire-3.5.3.8671"
31/03/13 11:44:39.149 CleanMyMacHelperTool[583]: Wont clean /Volumes/AlesisFirewire-3.5.3.8671 because disk image
31/03/13 11:44:52.727 coreservicesd[62]: Application App:"AlesisFirewireUninstaller" [ 0x0/0x7f07f] @ 0x0x7fb5c8c30050 tried to be brought forward, but isn't in fPermittedFrontASNs ( ( ASN:0x0-0x80080:) ), so denying.
31/03/13 11:44:52.727 WindowServer[85]: [cps/setfront] Failed setting the front application to AlesisFirewireUninstaller, psn 0x0-0x7f07f, securitySessionID=0x186a5, err=-13066
31/03/13 11:47:28.533 CleanMyMacHelperTool[656]: Mounted devices (
    "/Volumes/AlesisFirewire-3.5.3.8671",
    "/Volumes/AlesisFirewire-3.5.6.11675"
31/03/13 11:47:28.544 CleanMyMacHelperTool[656]: Mounted devices (
    "/Volumes/AlesisFirewire-3.5.3.8671",
    "/Volumes/AlesisFirewire-3.5.6.11675"
31/03/13 11:49:26.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in: no valid selfIDs for more than 3 minutes after bus reset.
31/03/13 11:52:39.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in: no valid selfIDs for more than 3 minutes after bus reset.
31/03/13 11:57:22.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in now active, GUID 003ee1fffe88dc6a; max speed s800.
31/03/13 11:57:34.000 kernel[0]: Alesis Firewire - 3.5.3.8671 preliminary - x86_64 CJ - May 3 2010 02:43:28
31/03/13 11:58:36.982 com.apple.launchd.peruser.501[155]: ([0x0-0x1d01d].tc.tctechnologies.AlesisFirewire.controlpanel[238]) Job appears to have crashed: Abort trap: 6
31/03/13 11:58:37.252 ReportCrash[242]: Saved crash report for AlesisFirewire Control Panel[238] version 3.5.3 (3.5.3.8671) to /Users/m1kygarcia/Library/Logs/DiagnosticReports/AlesisFirewire Control Panel_2013-03-31-115837_Mac-mini-de-Miguel.crash
31/03/13 11:58:39.831 system_profiler[267]: SPFWR ERROR: FireWire bus may be unstable. Other FireWire devices may be present.
31/03/13 11:58:50.676 com.apple.launchd.peruser.501[155]: ([0x0-0x23023].tc.tctechnologies.AlesisFirewire.controlpanel[274]) Job appears to have crashed: Abort trap: 6
31/03/13 11:58:50.837 ReportCrash[242]: Saved crash report for AlesisFirewire Control Panel[274] version 3.5.3 (3.5.3.8671) to /Users/m1kygarcia/Library/Logs/DiagnosticReports/AlesisFirewire Control Panel_2013-03-31-115850_Mac-mini-de-Miguel.crash
31/03/13 11:58:53.638 system_profiler[277]: SPFWR ERROR: FireWire bus may be unstable. Other FireWire devices may be present.
31/03/13 11:59:09.747 CleanMyMacHelperTool[300]: Mounted devices (
    "/Volumes/AlesisFirewire-3.5.6.11675"
31/03/13 11:59:09.905 CleanMyMacHelperTool[300]: Wont clean /Volumes/AlesisFirewire-3.5.6.11675 because disk image
31/03/13 11:59:09.906 CleanMyMacHelperTool[300]: Mounted devices (
    "/Volumes/AlesisFirewire-3.5.6.11675"
31/03/13 11:59:09.907 CleanMyMacHelperTool[300]: Wont clean /Volumes/AlesisFirewire-3.5.6.11675 because disk image
31/03/13 12:00:47.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in now active, GUID 003ee1fffe88dc6a; max speed s800.
31/03/13 12:00:59.000 kernel[0]: Alesis Firewire - 3.5.6.11675 (x86_64) Aug 16 2011 01:20:23
31/03/13 12:01:56.720 system_profiler[269]: SPFWR ERROR: FireWire bus may be unstable. Other FireWire devices may be present.
31/03/13 12:05:40.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in: no valid selfIDs for more than 3 minutes after bus reset.
31/03/13 12:08:52.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in: no valid selfIDs for more than 3 minutes after bus reset.
31/03/13 12:12:42.277 AlesisFirewire Control Panel[245]: -_continuousScroll is deprecated for NSScrollWheel. Please use -hasPreciseScrollingDeltas.
31/03/13 12:12:42.277 AlesisFirewire Control Panel[245]: -deviceDeltaX is deprecated for NSScrollWheel. Please use -scrollingDeltaX.
31/03/13 12:12:42.278 AlesisFirewire Control Panel[245]: -deviceDeltaY is deprecated for NSScrollWheel. Please use -scrollingDeltaY.
31/03/13 12:13:53.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in: no valid selfIDs for more than 3 minutes after bus reset.
31/03/13 12:25:29.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in now active, GUID 003ee1fffe88dc6a; max speed s800.
31/03/13 12:25:38.000 kernel[0]: Alesis Firewire - 3.5.6.11675 (x86_64) Aug 16 2011 01:20:23
31/03/13 12:28:30.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in: no valid selfIDs for more than 3 minutes after bus reset.
31/03/13 12:28:33.906 system_profiler[273]: SPFWR ERROR: FireWire bus may be unstable. Other FireWire devices may be present.
31/03/13 12:31:41.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in: no valid selfIDs for more than 3 minutes after bus reset.
31/03/13 12:35:16.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in now active, GUID 003ee1fffe88dc6a; max speed s800.
31/03/13 12:35:26.000 kernel[0]: Alesis Firewire - 3.5.6.11675 (x86_64) Aug 16 2011 01:20:23
31/03/13 12:37:53.513 system_profiler[266]: SPFWR ERROR: FireWire bus may be unstable. Other FireWire devices may be present.
31/03/13 12:39:36.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in now active, GUID 003ee1fffe88dc6a; max speed s800.
31/03/13 12:39:49.000 kernel[0]: Alesis Firewire - 3.5.6.11675 (x86_64) Aug 16 2011 01:20:23
31/03/13 12:42:55.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in: 53 bus resets in last 3 minutes.
31/03/13 12:46:50.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in: 68 bus resets in last 3 minutes.
31/03/13 13:01:30.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in now active, GUID 003ee1fffe88dc6a; max speed s800.
31/03/13 13:01:41.000 kernel[0]: Alesis Firewire - 3.5.6.11675 (x86_64) Aug 16 2011 01:20:23
31/03/13 13:05:27.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in: 79 bus resets in last 3 minutes.
31/03/13 13:06:31.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in: no valid selfIDs for more than 3 minutes after bus reset.
31/03/13 13:09:43.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in: no valid selfIDs for more than 3 minutes after bus reset.
31/03/13 13:13:31.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in now active, GUID 003ee1fffe88dc6a; max speed s800.
31/03/13 13:13:45.006 com.apple.kextd[11]: Can't load /System/Library/Extensions/IOFireWireIP.kext - ineligible during safe boot.
31/03/13 13:13:45.008 com.apple.kextd[11]: Load com.apple.iokit.IOFireWireIP failed; removing personalities from kernel.
31/03/13 13:13:54.818 com.apple.kextd[11]: Can't load /System/Library/Extensions/AlesisFirewire.kext - ineligible during safe boot.
31/03/13 13:13:54.823 com.apple.kextd[11]: Load tc.tctechnologies.driver.AlesisFirewire failed; removing personalities from kernel.
31/03/13 13:13:56.372 com.apple.kextd[11]: Can't load /System/Library/Extensions/AlesisFirewire.kext - ineligible during safe boot.
31/03/13 13:13:56.375 com.apple.kextd[11]: Load tc.tctechnologies.driver.AlesisFirewire failed; removing personalities from kernel.
31/03/13 13:15:40.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in: no valid selfIDs for more than 3 minutes after bus reset.
31/03/13 13:18:46.763 com.apple.kextd[11]: Can't load /System/Library/Extensions/IOFireWireIP.kext - ineligible during safe boot.
31/03/13 13:18:46.768 com.apple.kextd[11]: Load com.apple.iokit.IOFireWireIP failed; removing personalities from kernel.
31/03/13 13:18:46.797 com.apple.kextd[11]: Can't load /System/Library/Extensions/AlesisFirewire.kext - ineligible during safe boot.
31/03/13 13:18:46.800 com.apple.kextd[11]: Load tc.tctechnologies.driver.AlesisFirewire failed; removing personalities from kernel.
31/03/13 13:18:50.775 system_profiler[221]: SPFWR ERROR: FireWire bus may be unstable. Other FireWire devices may be present.
31/03/13 13:18:52.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in: no valid selfIDs for more than 3 minutes after bus reset.
31/03/13 13:21:03.488 system_profiler[235]: SPFWR ERROR: FireWire bus may be unstable. Other FireWire devices may be present.
31/03/13 13:22:37.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in: no valid selfIDs for more than 3 minutes after bus reset.
31/03/13 13:24:07.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in now active, GUID 003ee1fffe88dc6a; max speed s800.
31/03/13 13:24:19.000 kernel[0]: Alesis Firewire - 3.5.6.11675 (x86_64) Aug 16 2011 01:20:23
31/03/13 13:31:00.926 system_profiler[316]: SPFWR ERROR: FireWire bus may be unstable. Other FireWire devices may be present.
31/03/13 13:33:03.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in: 134 bus resets in last 3 minutes.
31/03/13 13:35:11.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in: no valid selfIDs for more than 3 minutes after bus reset.
31/03/13 13:38:24.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in: no valid selfIDs for more than 3 minutes after bus reset.
31/03/13 13:41:36.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in: no valid selfIDs for more than 3 minutes after bus reset.
31/03/13 13:44:48.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in: no valid selfIDs for more than 3 minutes after bus reset.
31/03/13 13:58:13.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in: no valid selfIDs for more than 3 minutes after bus reset.
31/03/13 14:01:25.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in: no valid selfIDs for more than 3 minutes after bus reset.
Can somebody help, please i´d gladly appreciate it.

I have this
System Profiler[170]
SPFWR ERROR: FireWire bus may be unstable. Other FireWire devices may be present.
& this
kernel FireWire (OHCI) Lucent ID 5901 built-in: no valid selfIDs for more than 3 minutes after bus reset.
Pls, help!!

HT201269 Hi I want to back up my photos from my iPhone 5. How can I do this? I have an iPad mini but cannot sync to an iPhone as iPad does not have USB port. Can you help please x

Hi I want to back up my photos from my iPhone 5. How can I do this? I have an iPad mini but cannot sync to an iPhone as iPad does not have USB port. Can you help please

You have to back them up to a computer. You would import them either to iPhoto or to the Photos app in your PC:
http://support.apple.com/kb/ht4083
Cheers,
GB

Airport Extreme v7.3.3 Port Mapping Port 80

I have a DVR in my home which is connected to my home network. It has a static IP address. I would like to be able to utilize its mobile app from any mobile/cellular network. The manufacturer of my DVR tells me that I need to open up Port 80 on my router, which is an Airport Extreme running v7.3.3.
I have tried looking up solutions and have found similar results but nothing for the AirPort running v7.x.x. Everything I have found is for version v6.x.x or v5.x.x.
I have tried using the following examples with no success, which may be fault on my part, as well as the document:
AirPort - Port Mapping Basics using AirPort Utility v6.x
http://portforward.com/english/routers/port_forwarding/Apple/AirPortExtreme/defa ultguide.htm
Re: How do I open ports on my airport extreme and assign a fixed IP Address for a device connected to my network?
Any further advice would be welcome. Thank you. I will gladly provide further details upon request/as needed.

I have tried looking up solutions and have found similar results but nothing for the AirPort running v7.x.x. Everything I have found is for version v6.x.x or v5.x.x.
Unfortunately, you have the firmware version of the AirPort mixed up with the software version of AirPort Utility, the application used to setup and administer the AirPort router.
Your AirPort was setup using software either by AirPort Utility 6.x...or....an iPad or iPhone running the iOS version of AirPort Utility. Either of those applications will allow you to set up port mapping......IF.....the AirPort is setup as the main router on your network.
Or, in other words....you do not have the AirPort connected to another modem/router on the network.
Now might be a very good time to confirm on the make and model number of the device that you call your "modem", since that will dictate the next move as far as setting up ports.

WRT54GS utorrent port forwarding (HELP PLEASE)

Hey everyone, I bought my WRT54GS router yesterday and cant forward utorrent ports. I have a static IP set up and am trying to use port 32069. I am sure all of my settings are correct in the port forwarding section, nad have tried checking/unchecking "enable". I think i've tried everything so far and it still wont work. If anyone can help me with this, it'd be greatly appriciated.
Message Edited by SinInSpira on 06-28-2007 09:28 PM

if the ports are not getting forwarded , try upgrading / reflashing the router's firmware ..

TS2634 i have a ipad gen1 refurbished the wall usb charger keeps saying charging is not supported with this accesory and has taken 24 hrs to charge half the battery and this is a factory charger that uses the usb port whats wrong here help please

i just purchased a refurbished ipad gen 1 when i pluged in the wall charger with the usb cable a window came up and said (charging not supported with this accesory) the battry was almost dead so i pluged in the wall charger and
the battery has been charging for 24 hrs and is only 50%charged it is the factory use charger for this unit why does this error come up and why is it taking so long the software is up to date

Not normal. Take it to an Apple Store for evaluation.
Make a Genius Bar Reservation
http://www.apple.com/retail/geniusbar/
The quickest way (and really the only way) to charge your iPad is with the included 10W or 12W USB Power Adapter. iPad will also charge, although more slowly, when attached to a computer with a high-power USB port (many recent Mac computers) or with an iPhone Power Adapter (5W). When attached to a computer via a standard USB port (2.5W, most PCs or older Mac computers) iPad will charge very slowly (but iPad indicates not charging). Make sure your computer is on while charging iPad via USB. If iPad is connected to a computer that’s turned off or is in sleep or standby mode, the iPad battery will continue to drain.
Apple recommends that once a month you let the iPad fully discharge & then recharge to 100%.
How to Calibrate Your Mac, iPhone, or iPad Battery
http://www.macblend.com/how-to-calibrate-your-mac-iphone-or-ipad-battery/
At this link http://www.tomshardware.com/reviews/galaxy-tab-android-tablet,3014-11.html , tests show that the iPad 2 battery (25 watt-hours) will charge to 90% in 3 hours 1 minute. It will charge to 100% in 4 hours 2 minutes. The new iPad has a larger capacity battery (42 watt-hours), so using the 10W charger will obviously take longer. If you are using your iPad while charging, it will take even longer. It's best to turn your new iPad OFF and charge over night. Also look at The iPad's charging challenge explained http://www.macworld.com/article/1150356/ipadcharging.html
Also, if you have a 3rd generation iPad, look at
Apple: iPad Battery Nothing to Get Charged Up About
http://allthingsd.com/20120327/apple-ipad-battery-nothing-to-get-charged-up-abou t/
Apple Explains New iPad's Continued Charging Beyond 100% Battery Level
http://www.macrumors.com/2012/03/27/apple-explains-new-ipads-continued-charging- beyond-100-battery-level/
New iPad Takes Much Longer to Charge Than iPad 2
http://www.iphonehacks.com/2012/03/new-ipad-takes-much-longer-to-charge-than-ipa d-2.html
Apple Batteries - iPad http://www.apple.com/batteries/ipad.html
Extend iPad Battery Life (Look at pjl123 comment)
https://discussions.apple.com/thread/3921324?tstart=30
New iPad Slow to Recharge, Barely Charges During Use
http://www.pcworld.com/article/252326/new_ipad_slow_to_recharge_barely_charges_d uring_use.html
Tips About Charging for New iPad 3
http://goodscool-electronics.blogspot.com/2012/04/tips-about-charging-for-new-ip ad-3.html
How to Save and Prolong the battery life of your new ipad
https://discussions.apple.com/thread/4480944?tstart=0
Prolong battery lifespan for iPad / iPad 2 / iPad 3: charging tips
http://thehowto.wikidot.com/prolong-battery-lifespan-for-ipad
iPhone, iPod, Using the iPad Charger
http://support.apple.com/kb/HT4327
Install and use Battery Doctor HD
http://itunes.apple.com/tw/app/battery-doctor-hd/id459702901?mt=8
To Extend a Device’s Battery Life, Get to Know It Better
http://tinyurl.com/b67c7xz
iPad Battery Replacement
http://www.apple.com/batteries/replacements.html
In rare instances when using the Camera Connection Kit, you may notice that iPad does not charge after using the Camera Connection Kit. Disconnecting and reconnecting the iPad from the charger will resolve this issue.
 Cheers, Tom

Port Mapping...access home network remotely

Hello,
Has anyone successfully established port mapping through the AE (802.11n)?
SSH access has worked for me but nothing else. Apple tech support was courteous but unable to solve problem.
I'm trying to get port mapping (port forwarding on other routers) to work for AFP and FTP.
Any help would be appreciated.
Greg
iMac, MacBook Mac OS X (10.4.8)

Hi Greg,
Thanks for your response. I will try it out.
Yes, I did get her the new AE 802.11n.
I am so impressed by it, I would go buy it for myself to add the print server capability, and dual band feature.
To take advantage of N, I will either get a new Macbook Pro, or a new wireless card for my PB G4, preferrably the former.
Cris
Hi Cris,
I have actually been successful now with AFP too.
Does your sister have the new AE 802.11n? That's the
one I have and here's what I did.
1) Open AirPort Utility
2) Select Airport Extreme
3) Menu "Base Station", "Manual Setup"
4) Select Advanced icon
5) Select Port Mapping tab
6) Click "+"
7) Select a service "SSH" or "AFP" which ever you
prefer.
8) For ssh, private tcp port needs to be 22. Public
IP address should be the IP address of your sisters
imac on her local network. Private TCP port should be
22.
AFP is the same setup as ssh, except the Public tcp
port should be any unused port number, for example
5912. (You can get a list of used port numbers here:
http://docs.info.apple.com/article.html?artnum=106439
) and the private tcp port needs to be 548.
Helping your sister out will be much easier when OS
10.5 becomes available later this spring and perhaps
by the end of this month. Go to this link and click
on the iChat icon. It will show you ichat's new
capabilities. http://www.apple.com/macosx/leopard/
Hope that helps,
Greg
iMac, MacBook Mac OS
X (10.4.8)
Powerbook G4 (17") Mac OS X (10.4.9)

Help please, with port forwarding settings

I have an MSI RG60 wireless router (Ethernet hard wired to my XP Home PC) and don't know what settings to use for port forwarding, to enable my WinMX and BitTorrent clients to work successfully.
I have the port numbers, and assume that this information goes in the Service Port box, i.e. 6699, or 6881-6889.
I know which ports are TCP and which are UDP, but I don't know what IP address to enter or which Common Service Port type to choose. Can anyone help please?
I'm pretty sure that other settings in my PC are OK as I have successfully been running a Belkin router for a couple of years, and have only replaced it with the new MSI unit due to reliability problems.

It does indeed have port triggering, but it wants incoming and trigger port protocol info, along with trigger and incoming port numbers.
How can I type ipconfig into either of teh clients...WinMx or Bit Torrent?

Cannot connect remotely, setup is correct but did not try port mapping, i don,t know how please help

could someone please point me to the possible areas on my server where i can check why i cannot connect remotely. I have been trying for the past two months without success. i did not tru port mapping cause I don;t know how to do this and I was told that port mapping on my time machine is done automatically. I am running a mac mini lio server 10.7.3 Time capsule.

Most people are going to see that message as a result of not properly closing Firefox, and then attempting to reopen Firefox. This problem is most likely to occur on Windows Operating systems, less frequently on Linux and Mac systems but not unheard of on any system.
Because you are on a Mac, I am referring you directly to an article that has been reworded for each operating system.
: http://kb.mozillazine.org/Kill_application
To properly close Firefox on your Mac use "Firefox" button -> Quit Firefox, and not with the "X" in corner of window which simply closes the window and not necessarily Firefox.
When you get stuck as you have described you must Force Firefox to terminate as described at the end of the article:
Mac OS X
:Open Apple Menu and select "Force Quit". For Mac OS X 10.3 and later, you can also use the Activity Monitor found in your "Utilities" folder (Applications -> Utilities -> Activity Monitor).
<br><small>Please mark "Solved" one answer that will best help others with a similar problem -- hope this was it.</small>

Cant get port forwarding working, please help :(

I bought an airport extreme yesterday, and since then ive been trying to get port forwarding to work. I've set it up before on other routers, and while its always been a hassle, this is the first time where I might just give up and take the router back. I've been searching the boards for solutions, and ive implemented several of them without success, and a call to apple's tech support got me nowhere. Im sure im just using the wrong number or setting somewhere, but I just cant seem to find it.
One suggestion i read was to set up the routers connection to my modem manually, instead of through dhcp. When I switched from dhcp to manual, i noticed all the prior numbers except dns servers stayed entered, so i wrote down the ones from when it was set for dhcp and typed them in. My manual setup is:
I.P.: 68.197.191.59
subnet: 255.255.224.0
router: 68.197.160.1
dns: 167.206.245.68
167.206.245.69
every other setting i left on the default.
the dhcp range is 10.0.1.2 - 200
One entry recommended a static ip. I originally set one up with the dhcp reservation feature, but then another post said your ip should be outside the dhcp range. Not sure if either method is better, but ive set my system with the following static ip:
i.p: 10.0.1.201
subnet: 255.255.254.0 (i was unsure what to enter here, so i chose the same as the routers)
gateway: 10.0.1.1
in port forwarding i made an entry with 60000 for the 4 public/private tcp/udp and an ip of 10.0.1.201 (i have tried many other port numbers in the odd chance that the one i picked at random might have already been in use)
I left every other setting on the defaults. The nat settings (a setting im not familier with) is current set for enabled with the default host box above it empty.
I should mention, my pc is wired to the router. I am using utorrents port checking site, as well as canyouseeme.org. Neither can ever see my port, one simply says not open, the other says connection refused.
I hope someone out there can help me with this, as the router is great with this one exception, and I'd rather not return it.

For starters, it's probably not a bad idea to "factory reset" your device since it sounds like you've had a lot of people giving you different advice. This isn't to say that you've been given *bad advice* but, it may make things easier for a trouble-shooter if you start over from a "known" state.
That said:
You need to setup manual port mapping. The problem is, when somebody from the outside tries to access your computer, the Aiport (for lack of a better analogy) isn't expecting any visitors; so it turns them away. ---That matches what you are seeing from canyouseeme.org etc...
Your error was when you "made an entry with 60000 for the 4 public/private tcp/udp and an ip of 10.0.1.201" Essentially all that will do is make a mapping for one port. Port "60,000" which to my knowledge, isn't used by anything.
You have to tell the Airport specifically what "outside" ports (each and every one) that you want routed to what "inside" ip address.
I use:
Public TCP: 22,80,443,27900,13405
Public UDP: 123,7777-7783, 13405,6881-6999
Private IP Address: 10.0.1.201
Private TCP: 22,80,443,27900,13405
Private UDP: 123,7777-7783, 13405,6881-6999
This enables: telnet, http, ssh, bittorrent and unreal tournament from the outside and routes ANY AND ALL TRAFFIC from those ports to my PC at 10.0.1.201 on the inside.
If I ran AIM, or ICQ or one of those things, then you need to add the ports that that system uses to the list also.

Help! no port mapping tab in airport utility port forwarding.

Hello I am trying to port forward my airport extreme router to host servers. I watched every single tutorial on the internet but nothing works because I dont have a port mapping tab under advaced in airport utility. btw I am running bootcamp windows7. Thanks in advance

Where are you looking?
The settings for Router Mode are under the Network tab.

Which ports can i use for port forwarding / port mapping??

Hi,
i have set up one port forward with success but am unable to open any other ports it seems. i am using the following web site to check (http://www.yougetsignal.com/tools/open-ports/) , and no matter what port number i have tried to port forward, it always comes back with the message that this port is not open.
Mabe I just hit the jackpot with the first port (9080)...and maybe it is only possible to forward a single port....however I would welcome any advice out there.
I am using time capsule, and to port forward i am doing following:
port mapping
+ ener name
leave service blank
public udp ports 9000 (example)
public tcp ports 9000
ip address 10.0.1.x
private udp ports 9000
private tcp ports 9000
<continue>
description xxxxx
service name / type - leave blank
<done>
<update>
please help!!!

Hi,
This linke gives you the informations that you need.
http://zone.ni.com/devzone/conceptd.nsf/webmain/72c6fc6ce4ad4d1386256b1800794596?OpenDocument
TN

AEBS Gigabit 802.11n FW 7.2.1 - OS X 10.5.1 Port Mapping HELP!!!!

Hi
I have a AEBS with Gigabit Ethernet upgraded to Firmware 7.2.1. I am running OS X Leopard 10.5.1 and I am unable to successfully forward ports. Every time I query a port that I believe to have mapped successfully it appears closed using canyouseeme.org.
I have followed numerous instructions, but they all seem to be instructions for Tiger, I'm wondering if a setting has been missed. I have successfully assigned a static IP address to my machine but still the port appears to be closed. I do run the Leopard firewall using specific applications option (the third one), but I have also tried it with the firewall off and it still hasn't changed anything, the ports are always closed.
So now I'm pretty much stumped. Has any one actually managed to get a setup similar to mine working, with the ports being open? All advice appreciated.
Thanks
Message was edited by: dalyboy

Hello dalyboy. Welcome to the Apple Discussions!
Try the following to see if it will help ...
To setup port mapping on an 802.11n AirPort Extreme Base Station (AEBSn), either connect to the AEBSn's wireless network or temporarily connect directly, using an Ethernet cable, to one of the LAN port of the AEBSn, and then use the AirPort Utility, in Manual Setup, to make these settings:
1. Reserve a DHCP-provided IP address for the host device.
Internet > DHCP tab
o On the DHCP tab, click the "+" (Add) button to enter DHCP Reservations.
o Description: <enter the desired description of the host device>
o Reserve address by: MAC Address
o Click Continue.
o MAC Address: <enter the MAC (what Apple calls Ethernet ID if you are using wired or AirPort ID if wireless) hardware address of the host computer>
o IPv4 Address: <enter the desired IP address>
o Click Done.
2. Setup Port Mapping on the AEBSn.
Advanced > Port Mapping tab
o Click the "+" (Add) button
o Service: <choose the appropriate service from the Service pop-up menu>
o Public UDP Port(s): <enter the appropriate UDP port values>
o Public TCP Port(s): <enter the appropriate TCP port values>
o Private IP Address: <enter the IP address of the host server>
o Private UDP Port(s): <enter the same as Public UDP Ports or your choice>
o Private TCP Port(s): <enter the same as Public TCP Ports or your choice>
o Click "Continue"
(ref: "Well Known" TCP and UDP ports used by Apple software products)

Some Port Mapping help.

Ok was using a verizon wireless router/modem with my mac network. Did all my portmapping right through verizon router controls. (About the only thing that worked well).
Now......
I have an airport extreme N router. I am still using the verizon router as modem. I have a ethernet cord going out of the verizon router into my airport WAN connection. I tried port mapping in the airport extreme for FTP to my office server and now no traffic can connect. Is there something im still suppossed to be doing to the verizon router???? I have all wireless capabilities on the verizon turned off as well as any mapping. Verizon has been no help in this. I am mapping port 21 to that specific computer with people loggin in to my outside IP its definitely the right ip. Where is this getting stopped?

With this setup, you have two local network layers. Your Verizon router is distributing the 192.168.1.XXX addresses, one of which is being assigned to your Airport. Then your Airport is distributing 10.0.1.XXX addresses to any of the computers connected to it.
If the Verizon router is not forwarding any ports, then you will have no access to your local network(s) from the outside. If you want FTP access to a computer that's connected to your Airport, then you will need to forward port 21 from the Verizon router to the Airport's 192.168.1.XXX address, and then from the Airport to your computer's 10.0.1.XXX address. I believe this will work, but I have never tried that 2-layered setup myself.

Port Mapping / port forwarding - help please...again...

Similar Messages

Maybe you are looking for