Port mirroring on cisco 6509

We have cisco 6509,Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXI2a, RELEASE SOFTWARE (fc2).
I want to know, at a time how many interfaces can be configured as a source interface and at a time how many interfaces can be configured as a destination interface?

The 9100EM does not support port mirroring.
You might want to find a hub and use that to mirror the traffic.
http://shop.ebay.com/?_from=R40&_trksid=p5197.m570.l1313&_nkw=ethernet+hub&_sacat=See-All-Categories
Be careful though, many of those listed claim to be hubs are not and are in fact switches.

Similar Messages

ThinkPad USB 3.0 dock network port has problems with our Cisco 6509 switch

We purchased a ThinkPad USB 3.0 dock for and X1 carbon and the main issue we are having is the network port does not seem to work with our Cisco 6509 switch. I tried updating the firmware on the dock but it still hasn't fixed the issue. I was wondering if anyone else had run into this problem with any other networks out there.

I'm seeing the same issue with a ThinkPad W520. When I connect my ethernet cable directly to the laptop, my internet speeds are on par with my service provider of 18 Mbps. When I move that cable to the dock, I will only see 1.5 Mbps. I have two displays attached to the dock and I'm running Windows 7. I've updated the dock firmware and have installed the latest system drivers. Is there anything else to try?

Cisco 6509 with Reliability 255/255, txload 238/255, rxload 8/255 interface

Hi there,
I'm having an issue with my Cisco 6509. One of Internet configured as trunk Interface direct with a HP7500 is showing reliability 255/255, txload 238/255, rxload 8/255.
The Issue is that my Cacti Server show me that only 10% of the link is in use but if you look at txload you can see that almost 100% of the bandwidth is in use..
What can I do in order to figure out what's going on with this Interface. I'm thing about to put wireshark and configure a port monitor in order to capture the packets.
Is anyone has any tip to do a troubleshoot with this issue??
SWITCH01#show int port-channel 10
Port-channel10 is up, line protocol is up (connected)
Hardware is EtherChannel, address is c47d.4fbf.a8c2 (bia c47d.4fbf.a8c2)
Description: CORECISCO_X_COREHP
MTU 1500 bytes, BW 2000000 Kbit, DLY 10 usec,
reliability 255/255, txload 238/255, rxload 8/255
Encapsulation ARPA, loopback not set
Full-duplex, 1000Mb/s
input flow-control is off, output flow-control is unsupported
Members in this channel: Gi8/19 Gi8/20
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters 1w0d
Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 66043000 bits/sec, 23041 packets/sec
5 minute output rate 1871148000 bits/sec, 186439 packets/sec
15127300343 packets input, 6121405739799 bytes, 0 no buffer
Received 232321316 broadcasts (161670914 multicast)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
118621325538 packets output, 141124879219641 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
SWITCH01#
Regards
Adriano

This pretty much tells you your port channel is pretty full. How many ports in the channel?
5 minute input rate 66043000 bits/sec, 23041 packets/sec
5 minute output rate 1871148000 bits/sec, 186439 packets/sec

Port mirroring in routers

Hi,
Port mirroring(SPAN) is possible in Switches, let me know if there is any sorts of feature implemented in Routers...
Cheers
Akhtar

Cisco has added a new feature that supports mirroring traffic on a router called IP traffic export. You need to run IOS version 12.3(4)T or later.
Check out the link below for configuration guidelines:
http://www.cisco.com/en/US/products/ps6350/products_configuration_guide_chapter09186a0080455b94.html
HTH,
Sundar
*Please rate all helpful posts.

Regarding LACP commands on Cisco 6509 to connect server

Hi All ,
We have to connect two servers to cisco 6509 (sup720 with MFFC R7000) switches and we have to configure LACP on the 6509 to bundle two ports to get 2 Gbps through put.
Each server has four NIC ports ..out of which two ports will be connected to Switch 1 ( active ) and remaning two ports will be connected to switch 2 ( standby).
We are going to use below commands for LACP on both the switches.Apart from below commands do we need to have any other commands to make LACP to work as soon as we connect the servers.
Switch 1 :
set channelprotocol lacp 1
set port lacp-channel 1/1-2 73
set port lacp-channel 1/1-2 mode active
Set port vlan 10 1/1-2
set spantree bpdu-guard 1/1-2 enable
set port lacp-channel 1/9-10 85
set port lacp-channel 1/9-10 mode active
Set port vlan 10 1/9-10
set spantree bpdu-guard 6/9-10 enable
On the MFFC we have so many vlans along with vlan 10
int Vlan 10
ip address 10.10.10.2 255.255.255.0
standby 10 ip address 10.10.10.1
standby 10 timers 1 3
standby 10 priority 200
same series of port will be used on Switch 2 to connect servers.
Servers support LACP protocol only.
diagram is enclosed...If any suggetions on this would be appreciated..
Thanks ,
M S K

Interesting I thought all sup 720's were non hybrid and used IOS only . Guess you learn something everyday. Looks like it should work with what you
have as long as the servers are setup with lacp in a active/standby mode.

Port mirroring on SG300 questions

Hi all,
I'm troubleshooting a LAN issue I have, and I wanted to hook up wireshark to record traffic over the course of a couple of hours for later diagnostics. I went into the web administration interface, clicked Administration > Diagnostics > Port and VLAN Mirroring, and added a port mirror from the port I wanted to watch to a port to which I had connected a laptop. I picked the Tx and Rx options, and clicked Apply.
I did receive lots of traffic in wireshark, but I noticed immediately that the server on the port I had mirrored was suddenly unavailable on the network -- pings timed out. This lasted until I removed the mirror, then the server was suddenly reachable once again.
Does this feature not work the way I had thought it does? What I saw looked more like a forward than what I would call a mirror. The documentation leads me to believe mirroring is intended to be used in just the way I was attempting to use it.
Am I missing something?

Hi Lamint,
I have a SG300-10P for my test, I did the same thing you did in my GUI.
I was mirroring port 7 to port 8 ticking the item to mirror RX and TX
My PC with wireshark was residing on port 8.
I started a comtinuous oibg from my PC on port 7 at IP address 192.168.10.60 to my WAN routers LAN address, 192.168.10.1 .
As you can see from my screen capture below, my PC on port 8 caprtured both RX and TX packets on port 7.
Because my wireshark PC was on port 8, I could not access the management interface of the switch to show you my configuration, so I grabbed the configuration via hyperterminal.
See screen caopture below ( with some configuration items excluded)..
I would suggest, if you are having issues to allow the Small Business Support Center to assist you.
http://www.cisco.com/en/US/support/tsd_cisco_small_business_support_center_contacts.html
Hope this helps
regards Dave

Port mirroring on SRW2048 kills Wireshark workstation IP

I have a workstation on this switch that is running WireShark and I need to get packets to it. However the moment I turn on port mirroring the station loses IP connectivity to the network. I tried Rx only, Tx only and both and all three settings knock the workstation off the IP network. Is there something I am missing? Also, I noticed that I can only mirror 4 source ports to this one target port. I would like to select pretty much all the ports as source port. Why can't I do this? I was previously using an older DLink switch that allowed me to mirror all ports and I am pretty sure that other switches like the Cisco 2900 series let you select all ports as source ports.
Thanks,
Diego

I fully understand what you are saying but that isn't consistent with previous experiences with port mirroring. I have used Cisco Catalyst type switches and also DLink switches that allow you to mirror all ports on the switch to one destination port. And even with all ports mirrored IP connectivity to the destination port is maintained.
This is not so surprising on the Catalyst stuff which is considered maybe a bit more "high end" than Linksys but the DLink which is a cheaper switch has the ability to do this just as the Catalyst. It seems that the Linksys is inferior in this regard to the Catalyst and the DLink.
Sorry to hear that and hopefully a future firmware version will change this behavior.
Thank you very much for your help.
Rgds,
Diego

Catalyst Express 500 port mirroring capabilities

Does it have this switch some port mirroring capability (SPAN or other)?

See...
http://www.cisco.com/en/US/products/hw/switches/ps708/products_tech_note09186a008015c612.shtml#Cat500

SLM2024 port mirroring breaks network connections

Hi all, I got an SLM2024 that I want to use with my network probe app to analyze packets, I have my network probe PC plugged into the target port and uplink to firewall's trusted port to source port of 2024. Now whenever I enable port mirroring on the 2024, I lose all network connections on the 2024, I searched around here but didn't really find my answer. If anyone's seen this before, any pointers would be great.

Hi Crash, thanks for the reply, yeah it's a similar setting on that model just with a different layout on the admin page, what I meant on the trusted port part is, I have a netscreen firewall and the trusted port of the firewall goes into the source mirrored port of the slm2024, and my PC is on the target port. And I have those mirrored with a setting for both tx and rx, whenever I enable mirroring it halts traffic from the firewall, and others that are on the 2024 like server/workstns.
But network probe works and I can see traffic. We had a cisco catalyst before and that had no problems using the span feature.

ASR901 port mirroring

ASR901 does not support port mirrioring as in other platforms.
Insted we can use following for port mirroring.
901(config)#service internal
901(config)#^Z
901#
901#test mirror 1 both 11
Here gig 0/0 interface will be mirrored to gig 0/10 interface.
What is the use of service internal command. It is not documented anywhere.....

Hello Sanjeewa
service internal command is a hidden command that is used to enable certain command line features as may be used by Cisco engineer to check some internal commands of the platform while troubleshooting. This command enable internal platform level commands. Like for example on 7600/6500 platform, you can perform ELAM capture (used to capture a single packet either on DFC or SP ) only after you enable "service internal".
Hope this answers your question. Let me know if you have any further questions.

ASR1001 Port Mirroring

Hi
anyone can help me how to do the port mirroring on ASR1001 router?

Hi Zeeshanraza,
From this Cisco documentation: Configuring ERSPAN
"The monitor session span-session-number type local command is not supported on Cisco ASR 1000 Series Routers."
Alternatively you can try using ERSPAN as Local SPAN
Example: Configuring an ERSPAN as a Local SPAN
The following example shows how to configure an ERSPAN as a local SPAN.
monitor session 10 type erspan-source
source interface GigabitEthernet0/0/0
destination
erspan-id 10
ip address 10.10.10.1
origin ip address 10.10.10.1
monitor session 20 type erspan-destination
destination interface GigabitEthernet0/0/1
source
erspan-id 10
ip address 10.10.0.1
Regards,
Hendro

RV180 Port Mirroring

Has anyone had any success with port mirroring on the RV180?
The data sheet refers to port mirroring capability, but I can't find the configuration settings anywhere?

Duplicate posts.
Go here: http://supportforums.cisco.com/discussion/12156511/rv180-port-mirroring

Port Mirroring SRW2048

Hello,
Does anybody know the specifications about port mirroring funcionality for Cisco SRW2048 48-Port Gigabit Switch?
I need to know about:
1.- Is there any limit in port mirroring sessions?
2.- Can one target port receive traffic from multiple ports?

Hi Dave,
Thanks for your answer, of course I understand I can't have 4 Gbps out of the egress port, bust sometimes we know that even when the link is 1 Gbps the traffic is not going to fill that bandwidht.
Regarding the sessions question, I understand by your response you can have:
Source Port    Type                      Target port
g1                           Rxonly                   g3
g2                           Rxonly                   g3
g4                           Rxonly                   g6
g5                           Both                      g6
Can you confirm this?
We are evaluating to propose this switch to a customer and we need to have this feature.
If there isn't any limitation in mirroring traffic, except logical bandwith capabilities, then I can't understand why Catalyst 2960 have a limitation to one or two monitor sessions ... The catalyst are suposed to be better switches ......
Best Regards

Cisco 6509 with 10G Module

Hello,
We have Cisco 6509 Core Switch with following details & we need to install WS-X6716-10T-3C module in int.
Can some body advise which slot number i should use in 6509 ?
Do i need to upgrade supervisor engine IOS for this ?
Is it hot swapable module & can i install this module in production ?
6509_CORE#sh ver
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXI6, RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Mon 28-Mar-11 12:09 by prod_rel_team
ROM: System Bootstrap, Version 12.2(17r)SX7, RELEASE SOFTWARE (fc1)
6509_CORE uptime is 2 years, 30 weeks, 1 day, 3 hours, 13 minutes
Uptime for this control processor is 2 years, 30 weeks, 1 day, 1 hour, 44 minutes
Time since AUB_CORE switched to active is 2 years, 30 weeks, 1 day, 1 hour, 44 minutes
System returned to ROM by power cycle at 11:55:23 UTC Wed Apr 27 2011 (SP by power-on)
System restarted at 11:16:22 AST Sun Jun 26 2011
System image file is "sup-bootdisk:s72033-adventerprisek9_wan-mz.122-33.SXI6.bin"
Last reload reason: Reload Command
cisco WS-C6509-E (R7000) processor (revision 1.5) with 983008K/65536K bytes of memory.
Processor board ID SMC1426001S
SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache
Last reset from s/w reset
4294967295 Ethernet interfaces
33 Virtual Ethernet interfaces
150 Gigabit Ethernet interfaces
100 Ten Gigabit Ethernet interfaces
1917K bytes of non-volatile configuration memory.
8192K bytes of packet buffer memory.
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
6509_CORE#sh module
Mod Ports Card Type                              Model              Serial No.
1   24 CEF720 24 port 1000mb SFP              WS-X6724-SFP       SAL1430P2QU
2   48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX     SAL1429N6XB
3   16 CEF720 16 port 10GE                    WS-X6716-10GE      SAL1430NYUE
4   16 CEF720 16 port 10GE                    WS-X6716-10GE      SAL1430NX5A
5    5 Supervisor Engine 720 10GE (Active)    VS-S720-10G        SAL1430NUJE
7   16 CEF720 16 port 10GE                    WS-X6716-10GE      SAL1645RJTF
Mod MAC addresses                       Hw    Fw           Sw           Status
1 d0d0.fd62.d9e0 to d0d0.fd62.d9f7   4.4   12.2(18r)S1 12.2(33)SXI6 Ok
2 c84c.75b8.596c to c84c.75b8.599b   3.4   12.2(18r)S1 12.2(33)SXI6 Ok
3 001f.6cac.11d0 to 001f.6cac.11df   1.0   12.2(18r)S1 12.2(33)SXI6 Ok
4 5475.d06e.0988 to 5475.d06e.0997   1.0   12.2(18r)S1 12.2(33)SXI6 Ok
5 001e.4a7f.3068 to 001e.4a7f.306f   3.2   8.5(4)       12.2(33)SXI6 Ok
7 fc99.4736.2d80 to fc99.4736.2d8f   1.1   12.2(18r)S1 12.2(33)SXI6 Ok
Mod Sub-Module                  Model              Serial       Hw     Status
1 Distributed Forwarding Card WS-F6700-DFC3C     SAL1430P282 1.4    Ok
2 Centralized Forwarding Card WS-F6700-CFC       SAL1430NRAS 4.1    Ok
3 Distributed Forwarding Card WS-F6700-DFC3C     SAL1430P26L 1.4    Ok
4 Distributed Forwarding Card WS-F6700-DFC3C     SAL1430NZRM 1.4    Ok
5 Policy Feature Card 3       VS-F6K-PFC3C       SAL1429N6B7 1.1    Ok
5 MSFC3 Daughterboard         VS-F6K-MSFC3       SAL1430NN3R 5.0    Ok
7 Distributed Forwarding Card WS-F6700-DFC3C     SAL1644RAZF 1.5    Ok
Mod Online Diag Status
1 Pass
2 Pass
3 Pass
4 Pass
5 Pass
7 Pass

Hello cmarva,
I got power requirement from core switch:
6509_CORE#show power
system power redundancy mode = redundant
system power total =     3795.12 Watts (90.36 Amps @ 42V)
system power used =      2748.06 Watts (65.43 Amps @ 42V)
system power available = 1047.06 Watts (24.93 Amps @ 42V)
                        Power-Capacity PS-Fan Output Oper
PS   Type               Watts   A @42V Status Status State
1    WS-CAC-4000W-INT   3795.12 90.36 OK     OK     on
2    WS-CAC-4000W-INT   3795.12 90.36 OK     OK     on
                        Pwr-Allocated Oper
Fan Type               Watts   A @42V State
1    WS-C6509-E-FAN      210.00 5.00 OK
                        Pwr-Requested Pwr-Allocated Admin Oper
Slot Card-Type          Watts   A @42V Watts   A @42V State State
1    WS-X6724-SFP        162.96 3.88   162.96 3.88 on   on
2    WS-X6748-GE-TX      325.50 7.75   325.50 7.75 on    on
3    WS-X6716-10GE       457.80 10.90   457.80 10.90 on    on
4    WS-X6716-10GE       457.80 10.90   457.80 10.90 on    on
5    VS-S720-10G         338.10 8.05   338.10 8.05 on    on
6    (Redundant Sup)       -     -      338.10 8.05 -     -
7    WS-X6716-10GE       457.80 10.90   457.80 10.90 on    on
system auxiliary power mode = off
system auxiliary power redundancy operationally = non-redundant
system primary connector power limit =   10920.00 Watts (260.00 Amps @ 42V)
system auxiliary connector power limit = 10500.00 Watts (250.00 Amps @ 42V)
system primary power used =              2748.06 Watts (65.43 Amps @ 42V)
system auxiliary power used =            0 Watt
As per Cisco document i require this power WS-X6716-10T-3C: 509.3W (12.1A @ 42V) & from output available power is system power available = 1047.06 Watts (24.93 Amps @ 42V)
Looks like im good to go. Can you verify please ?
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-6500-series-switches/product_data_sheet09186a00801dce34.html
Regards,

Trouble With Port Mirroring (SG200-08)

Trouble with port mirroring.
Even though both Tx and Rx is specified, only getting half the conversation. Ping reply only for instance. And when pinging from other locations no traffic at all.
Please help
SG200-008
FW Version: 1.0.2.0
Boot Version D.3.1
Thanks

I also have problem with the mirroring of port on my SG200-08. The firmware is 1.0.6.2.
I mirror the port g1, to which my router to the Internet is connected, to the port g2 to be able to see the traffic with a Centos system running Bandwidthd connected to the port g2. The problem is that I only see the traffic coming in (downloads from the Internet) and not the traffic comming out (uploads to the Internet).
When looking at the SG 200-08 on the web interface at "Status and Statistics/Interface" and looking at the port g2, I see values for the "Transmit Statistics", but all the values are at 0 for the "Received Statisticsc" (see the attached file)
I confirmed that in "Administration/Diagnostic/Port Mirroring" is set up both Tx and Rx (it does not work either if I have Tx or Rx alone: I do not see the uploda traffic to the Internet). See the attached file.
This is very annoying as I purchased this SG 200-08 especially for this and it does not do the job porperly.
Does anybody knows a solution to this?

Port mirroring on cisco 6509

Similar Messages

Maybe you are looking for