Port routing

I have a FIOS MI424WR router and would like to set up my security cameras to be viewed over the internet.
How do I setup Port forwarding with this router so that I can view them with internet explorer?

sorry for the long delay...The IP starting & ending address is 192.168.1.2 - 192.168.1.254

Similar Messages

I just bought a new iMac and I am using a apple air port router. How do I connect mt windows PC to the air port router do I can move files

I Just purchased a 21.5 iMac and connected it to the Internet using a apple air port router. How do I connect my windows PC to my air port router so I can transfer files.

It makes life easier to install the airport utility for windows.. which has a couple of different apps in it.. if you airport is new type then the utility is too old.. but is still valuable for Bonjour which provides network information for shared devices in the apple world to windows.. and a disk access agent..
It will also help the Apple computer access shared directory in the windows computer.. nowadays this is pretty easy.

Dual Wan and port routing

Hi,
I am setting up a configuration with SA520W and 2 Wan, in load balancing. But I face a problem that I could not understand.
Traffic is HTTP, SIP and 2 servers.
Servers are for a VPN tunnel and a mail server with ActiveSync
Both services absolutely need port 443 on the external IP, and that's one of the dual wan reason.
The 2 wan are running, load balancing mode is enable and NAt routing in firewall tab as follow :
443 Enabled     WAN     LAN     ALU_OpenVPN     ALLOW always     Any         192.168.0.150     WAN1     Always
443   Enabled     WAN     LAN     ActiveSync     ALLOW always     Any         192.168.0.254     WAN2     Always
If load balanced
Port 443 is NOT routed from wan1 to 192.168.0.150
Port 443 is routed from wan2 to 192.168.0.254
If only WAN 1
Port 443 is routed from wan1 to 192.168.0.150
If only WAN 2
Port 443 is routed from wan2 to 192.168.0.254
In fact I did other testing and no port routing with WAN1 when load balancing is enable, even on port that is not used at all on Wan2.
With a FTP filezilla server, it's OK if on wan2, and it stop before logging if on a wan1 (on laod balancing, ok on both case if only one wan)
Firmware : latest 2.1.18
Any Clue ??

Hello,
I confirm, there is a strange behaviour.
Simple test :
Dual Wan configured.
A FTP server on the LAN (192.168.0.254) port 21
Firewall , ipv4 config :
WAN   to   LAN     FTP     ALLOW always     Any         192.168.0.254     WAN1
WAN   to   LAN     FTP     ALLOW always     Any         192.168.0.254     WAN2
Then some testing using a FTP client outside the LAN, connection from Internet.
Then, changing ONLY the Wan Mode :
1/ Use only single WAN port : Dedicated WAN
==> FTP connect through WAN1
2/ Use only single WAN port : Optional WAN
==>FTP connect through WAN2
3/ Load Balancing
==>FTP connect through WAN1
==>FTP DO NOT connect through WAN1
Is that a bug or do I have some strange stuff somewhere ?
I will pick up another SA520W from stock, brand new, update the firmware, configure the 2 WAN (invering the 2 provider just in case) and do the same test.

Can I activate the ethernet ports (routing) of Time Capsule "joining" an existing non-Apple wireless network ?

Hello,
I have a DSL modem that is also a WIFI router as my main WIFI network from room A. In room B, I have a TC wirelessly joining the existing WIFI network (not creating a new one). That works fine, I have one SSID, and I can wirelessly access the TC disks and backup my Mac on my TC.
Now, I would like to connect a wired device (with on WIFI) to the ethernet port of my TC. Unfortunately, the ethernet ports of the TC don't seem to be "activated" as they do not have internet on them.
More precisely, I'd like to connect a GE Cordless Skype Phone Model# 31591 (http://www.gephones.com/products/skype/dect-6-0-expandable-digital-cordless-phon e-with-skypetm.html) that connects to a router via Ethernet. I'm aware that I could simply connect it to the DLS router, but that's not what I want... Is there any way to activate the ethernet ports of the TC while in "join" mode ? Or do I really have to buy a Airport Express to create my main network and then extend it ?!?

Thanks, the reason why I asked again, is because you told me to start another thread with the specifics of the device I want to connect, so I did
Not a big deal, and it is easy to become confused.....but to be clear about this
Your question.....
is there a way I can connect my Bluray player to the TC ?
My Answer.....
Please start a new post for that. Tell us the make and model number of the player and whether you plan to connect using wireless or Ethernet.
so I tried to creat the main WIFI network with a first-generation Airport Express M9470LL/A (802.11b/g, no "draft N" or "n" support) and the TC wouldn't extend it either, is it too old/not supported
Unfortunately, the "extend" setup will only work with "n" devices. The older Express does not have a setting to "Allow this network to be extended", so the Time Capsule cannot pick up the signal.
I'm not sure what else to suggest other than what I already have. I'm assuming that you do not want to buy another new Airport Express.

Sockets and ports - routing messages between machines? helpppp!

Hi,
I'm new to java and am hoping someone out there can help me, hoping this is an ok place to post this:
If all you need to create a connection is an IP address and a port number, using streams...
Can you route messages from A to B then from B to C, where A looks up C through B having a hash table which contains C's IP address and port number?
And how in the first instance does B know about A's IP address? All the examples I've seen the IP address is hard coded?
Thanks in advance!

I'm not sure what you are really trying to do... Can you explain in more concrete terms? Are you writing a chat client + server or something like that?

MacBook (10.4.11) and Belkin-G 4-port Router...

Hey everyone,
I just bought a new router for our apartment and my macbook is having a hard time connecting. Like the topic says, I am running OS X 10.4.11 and trying to connect to the Belkin G-router (Model: F5D7234-4). I can connect to it and my airport shows that I have 4 full bars. However, I can't actually do anything internet related such as browsing. Firefox/Safari say that I am not connected to the internet. My friend, who has a newer MacBook running 10.5, has no problems connecting and using the internet.
Why can't I connect via air port? Wires is no problem.

I'll try creating a new network location.
I have no idea what these websites use, all I know is that I cannot access them unless I disconnect, reconnect, then immediately spam my browser.
Examples: I cannot access anything related to my school including e-mail..
http://www.emory.edu
https://classes.emory.edu
However, not just limited to my university. I cannot access..
www.gatech.edu
www.uga.edu
www.gsu.edu
However, I just noticed something. I CAN access out of state web pages just fine.. like www.ucf.edu (guess i'd just never tried before) http://www.nd.edu/ was fine too.
Message was edited by: DominicanoATL

WAN Port & Router Mode

Can someone please explain to me how to properly configure two linksys routers (such as WRT54G) so that one is an internet gateway and the other is a router for a different subnet but can still access the internet through the other router's gateway.
Obviously the internet gateway router would be in "gateway" mode and the second router would be in "router" mode. I'm assuming that the cable should run from the WAN port of the second router to a LAN port on the gateway router.
With this configuration in mind, what settings would I need to adjust in order for these two routers to successfully communicate with one another and for pcs on both routers to successfully communicate with each other through the routers. Also, I need all pcs, regardless of the router to which they are connected, to access the internet through the gateway router.
Do I need to ajust RIP settings? Static routes? Static IP addresses?
Any help is greatly appreciated!

I have had some success! But not much . I restarted the adsl router and was assigned an ip address for my MBP and could connect to the internet through the new wireless network. Yee-ha. But when I try to add additional devices to that network they will not connect unless I restart the adsl router each time. Also when I disconnect and try reconnect my MBP to the new wireless network we are back to square one unless I restart the router. So it looks like it is a router issue. I would be really grateful for any suggestions as to what I should change on the adsl router?? It is a TP-Link TDW8961ND.

Need more than 4 port router

Hello,
I need to connect more than 4 computers/game systems to the router, how do I go about doing this? Do I need a router with more ports or is there another way? Thanks
Solved!
Go to Solution.

chet wrote:
Could you guide me as to how to add this switch?
One of the ways of doing that, is having a second router and following...
portforward.com -> forum -› Knowledge Base -› Using a Second router as a Switch/Hub/WAP
http://forum.portforward.com/YaBB.cgi?num=1133918703
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

Issue Forwarding Port 7000 on RVS4000 Router

Hi Everyone,
I have recently replaced a WatchGuard Firebox SOHO 6 with a Linksys 4 Port Router Mod: RVS4000 because the WatchGuard was becoming unstable.
I set up the new router with all the settings from the previous equipment, which included forwarding port 7000 to a specific IP.
This port broadcasts images from a surveillance software installed on a computer with a static IP (the computer runs on Vista).
In order to view the broadcasted video on another computer, I use a proprietary software not a web browser.
So far, I tried single port forwarding without being able to view the images and range port forwarding with the same result.
I spend over an hour with the Business Tech Support from Linksys without success. They even remoted into the device and found nothing suspicious.
Currently the router runs on firmware version 1.2.11 and the Tech Support people suggested upgrading to a newer version.
I'm concerned to do so because I in read other postings that I can run into a bigger problem (i.e. bricking the router).
Finally, other ports are being forwarded (i.e. port 3389 RDP) and it works fine, so at least I know the forwarding feature is working properly.
Can someone shed some ligh as to what to do next?
Needless to say, everything was working fine with the WatchGuard Firebox and no changes in equipment, IPs or other software/hardware have been done.
Thank you in advance fro your help.
danielk

Greetings,
That sounds peculiar that some ports would get forwarded but others not, you might want to check and see if your ISP is blocking the ports if your going through the internet to this security application. If everything is local, then you should try to follow the advice of upgrading your firmware to the latest version, in order to avoid "bricking" your router do the following sequence, before you upgrade:
do a backup of your configuration (optional)
Reset router to factory default settings from the GUI.
Upgrade to latest firmware.
Reset router to factory default settings again from the GUI.
Configure everything again manually *RECOMENDED*
This somewhat ilogical sequence of events prevents the IOS from being corrupted and has worked in many cases I have dealt with regarding router "lock up" issues.
Besides that the only thing else I can think of is find out if there are any more additional ports required for this application to work properly and check to see if your using the exact protocol UDP or TCP for the ports that are being forwarded.
Regards.

Router ACL and Port ACL

how to find out after looking at the ACl that this is router acl and this is port acl.
is there is any syntax difference between these two acl's? or these two look the same.

how to find out after looking at the ACl that this is router acl and this is port acl.
It depends on where the ACL is applied:
Layer-3 interface (SVI, routed port): Router ACL
Layer-2 interface (physical switch interfaces): Port ACL
is there is any syntax difference between these two acl's?
Both support Standard and Extended ACLs, the Port ACLs support MAC Extended ACLs in addition.
Link: c3560 Configuring Network Security with ACLs

Internet drop outs on my G5 since I use a wired router instead of wireless

Hi guys!
I used to have wireless internet at home (1 x G5 & 2 x windows laptops). Internet worked fine and fast. Although I couldn't get all computers into a internal network (for easy sharing files...), but that's not the issue now.
Anyway, I have a new roommate in the house that doesn't have wireless on his windows pc. So, I connected all computers to a 4 ports router. I ditched the whole wireless thing because I couldn't get it working together with the wired router thing. So all computers are linked to the router by cable.
Now, at first everything worked fine. All computers had internet and I even had my long awaited network so that I could share files at high speed between computers (mac - windows). Suddenly, I guess after a couple of hours, my mac started having difficulties finding the network. At times I have no internet, or it takes looooooooooooooong to load up webpages and sharing files with my windows laptop takes like 6hours for 3giga (which normally is done in a couple of minutes). My windows laptop has no problem with internet, no drop out no nothing, everything works fine (except sending files to my mac which also takes hours...).
Anybody knows what to do?
Also anyone knows if the following is possible:
- cable comes in my house (WAN)
- goes to wired 4port router
- from the router 1 wire goes directly to a pc
- from the router another wire goes to my wireless accesspoint which then would be used to connect 1 or more wireless pc's.
- with all that, I'd like to have internet on all computers AND have a fully working network between all computers (mac and windows)
Anyone knows if this is possible?
Thanks for your time!

The wireless access point is a D Link Airplus G+ 2.4Ghz. It has no extra ethernet ports.
I also thought of having a wireless router with extra ethernet ports. But of course this would mean another cost... I was hoping that I could fix it with the things I allready own.
But, nevertheless, there might be a little change in things as I just tried connecting with the second ethernet port on my mac. Haven't had any problems yet (+/- 10minutes). Am gonna try to send big files to my laptop in order to test the speed between them.
Will get back with the results.
Thanks for your help!

Using linksys wired router with AE 2nd generation

Hi. I'm trying to use a linksys befsr41 (non-wireless 4 port router) with a 2nd generation airport express. I have several wired rooms that I want to setup separate networks with other AE's. My configuration is: cable box-->AE WAN in--AE LAN out-->Linksys-->ethernet cable through the house—>AE WAN in rooms. Can’t seem to make this work. I can do it wirelessly (i.e having the remote AE's joing the first AE network) but several of the rooms have poor signal. As soon as I try and create a new network the remote AE’s can’t connect to the network. I checked the cables and they are all good.
Thanks.

We need some additional information to be able to troubleshoot this issue.
Can you provide the make and model number of the cable modem that you are using?
Are the other AirPort Express devices that you are trying to connect also 2nd Gen versions? If not, what version are they?
The Linksys router needs to be configured to operate in Bridge Mode so that it will function as if it were an Ethernet switch.....not a router. Is the Linksys set up in Bridge Mode at the current time?
Looking at the Linksys support forum....example below......I cannot tell whether it is possible to configure the Linksys product in Bridge Mode:
https://community.linksys.com/t5/Wired-Routers/Use-BEFSR41-in-Bridged-Mode/td-p/ 272061
Are you trying to configure the AirPorts using AirPort Utility on a Mac....or on an iPhone / iPad? If you are using a Mac, what operating system is the Mac running? If you are not sure, click the Apple icon in the upper left corner of the screen, then click About This Mac. Post back with the OS X version that you see there.

Linksys WRT110 Wireless Router

I need to setup my Linksys WRT110 wireless router for wireless use as well as a router between my cable modem and my desktop PC. So far, I cannot find any documentation on how this is done or if it is possible at all. When I called Linksys support they told me it can be done and provided me with a link to the instructions, however, they did not work. Does anyone know if this is possible? I need to setup in order to work from home and I cannot use a wireless connection to my cable modem but I need a router between my desktop PC and my cable modem. Oh, by the way, I have a new HP desktop which is running Windows 7. I would appreciate any help someone can lend me. Thank you. SHH

From what i read on your post looks like your trying to use your wrt110 as a wireless access point and you want to still use your router near your modem.
To do this what you have to do is disable your wrt110 as a dhcp server since your other router near your is acting as the dhcp server.
So what you do is hook a cable to your wrt110 in port 1. type in 192.168.1.1 in the address bar of your internet explorer.For now this 192.168.1.1 number will get you into the wrt110 until you change it to 192.168.1.5 under setup you will see 2 areas. Under the ip address type in 192.168.1.5 so this make your wrt110 have this ip address.
Below that you will see DHCP server setting disable this. So your wrt110 will not act as the dhcp server it will act as a wireless access point.
Now if you type 192.168.1.1 in your web brower that will open the configuration screen of the router next to your modem. Which that dchp server setting will be enabled.
So basically from your modem your first router will route the signal from the modem thru the router to the computers hooked to it. then say you run a cable from that router to the wrt110.So basically your just uplinking to the wrt110. only thing is your wrt110 will have to act as a access point instead of a router.
Your main router configuration screen to get into it. you would type 192.168.1.1 in your brower after you setup your wrt110 an disable the dhcp server and set the ip to 192.168.1.5 when you type this number the 105 number in your browser it will go into the web config screen of the wrt110
So to access the web config screens of both routers they will have different numbers.
1st router by your modem will be 192.168.1.1
2nd wirless one will be 192.168.1.5 which you changed when you when in and disable it as a dhcp server since your 1st router by your modem acts as the dhcp server.
Hopefully this will help. I know it does get a little confusing been there and done that more then once. If not call linksys on the phone tell them what products you have and how you want it to work they will walk you thru it.
My setup in my home from my modem it connects to a 4 port router, then from there to a 24 port switch then uplinks with a Power over Ethernet adapter which sends power thru this little adapter over the brown pair in the cable so you dont need a electrical outlet where you put your wireless access point/router. Then from my switch it uplinks with that POE to a Wrt110 upstairs in my home. I know what a pain this can be i've call them more then once to get mine setup and working.
GOOD LUCK HOPE THIS HELPS

Imac to PC router Question

Hello,
I am going to need a router for the imac. The Imac will be connected to the router, and a PC with a linksys wirelessG adapter will be the secondary machine picking up the signal.
Can anyone reccomend a router that works well for Mac to PC networking?

Only Shapes, welcome to the discussions.
You can use just about any Router on the market the technology is the same for both PC and MAC.
Since you have a Wireless G adapter all you need is any 802.11g Multi port Router and you should be good. You may want to read the instructions you recieve with your choice of Router.
If you decide to make your Network Wireless you will need to make sure that your choice of 802.11g Router is Wireless.
All of the major manufactures make good products, and you will get several different opinions from people that have had good luck with there particular brand.
Cheers Don

Mulipe router/switch/hub home setup

Home Network Port Set-Up
My home network is as shown in the figure below:
(Can not attach graphics so I explain:
4 port speedtouch router connects to the ISP.
On this I have hung
x-Canon iP5200R network and wireless printer.
y-AirportExtreme
On the Airport I have hung
a-USB hub with 2 WD MyBook's
b-iMac G5
c-iMac G4 lamp
d-MacBook or Dell Windows laptops as and when I need to transfer large files)
The units connected to the Airport LAN ports cannot see any devices connected to the speedtouch. Originally there was only one 4 port router with built in wireless. After that there was another 4-port router with no wireless. I am therefore 100% certain that the printer have communicated through the Ethernet cable, not wireless.
I have circumvented the problem of not seeing devices on the other switch by just connecting items that should see each other to the same switch. When I got the speedtouch and airport a year ago, I just connected as this and it worked.
Today my daughter try to print and it did not work, error message 306 – check communications with printer.
I find that
1. The test page does print from the Canon IJ Print Utility
2. In the Canon IJ Print Utility both wireless printing AND wired printing is selected
I deselect WL printing, and the printer disappears.
From this I deduce that the printer must have been using the WL printing facility not the cable facility, but that it stopped working today for some reason.
So I have two issues.
1. How do I make the devices on the airport the speedtouch see each other (I guess I must open a port on the airport. This will disable its firewall functionality, but that does matter as the speedtouch has a firewall)
2. Why did the printing stop working – this may not really matter if I can get these to see each other on the network
Thank you for your support

It doesn't allow me to select ethernet as an option for internet connection, only dchp, ppoe and one more which isn't ethernet.
DHCP is correct setting. .it will use ethernet but the new AC TC has problems.. it needs a crossover cable with some switches. Or you need to return it and get it replaced as there is something wrong with its wan port.. the new AC model needs a hardware revision and about 3 or 4 firmware upgrades before it hits the status of the Gen4 it replaced.
My questions are: should I connect my time capsules together directly with ethernet using another available port in my new time capsule. I thought my switch would work better. Also, does one time capsule have to be in router mode instead of having both of them in bridge.
Both should be in bridge.. but you can rearrange things to see if any of the other devices works better.
You can use the billion or the old TC.. plug the new TC into those.
Bob is correct though.. the switch is the correct thing for everything to be plugged into .. but in home situation what works is more important than what is best. It if fails in all of them then the WAN port is proven faulty.
Should I be able to use the hdd on the 2nd (older) time machine as essentially a networked hdd for putting movies and music on, and use my new time capsule as the sole backup (occurring both over ethernet for my iMac and wifi for our laptops)
Yes, that is ok.. you just need to get the AC version TC actually working properly.
Give us a few screenshots of things.. that really helps to see.
Click on each unit and show the summary pages.

Port routing

Similar Messages

Maybe you are looking for