Port Stopped: Y

Hi,
I have a 1921 Router with two gig interfaces but only one of them seems to work.
Both of them are connected to a 3750 switch with the same config on both ports.
I have tried different cables but no difference. I had a look on the command show controllers for the interfaces and found this
lon-er01#show controllers gig0/0 | i Port
Port Stopped: Y
lon-er01#show controllers gig0/1 | i Port
Port Stopped: N
The configuration
interface GigabitEthernet0/0
description mgmt
ip address 172.24.55.9 255.255.255.0
duplex auto
speed auto
interface GigabitEthernet0/1
ip address 10.150.0.1 255.255.255.0
duplex auto
speed auto
end
lon-er01#show ip inter brief
Interface                  IP-Address      OK? Method Status                Protocol
GigabitEthernet0/0         172.24.55.9     YES NVRAM down                  down
GigabitEthernet0/1         10.150.0.1      YES NVRAM up                    up
Any idea why it says "Port Stopped: Y"?
Thanks for your help

- Swap the cables between gig0/0 and gig0/1. Gig0/1 was previously up and
working so it is a known good link. If you plug that link into gig0/0 and
gig0/0 comes up then obviously there is no issue with gig0/0.

Similar Messages

MDB and Database - Listener port stops working

Hi,
I have created an MDB which does the following when a message is received from the queue.
1. Store message in database
2. do some processing
At step 1, if there is any issue with the database connection (e.g. database is not available etc), I rollback transaction. My idea is to leave the message on queue for now and retry it again after some time unless the database is back again. "Maximum retries" of the listener port is set to N but since there is no retry interval available, all N retries are done in a flash and my listener port stops working. I cannot use backout mechanism as I have to wait for the database to be back again. What are my options?

usmanchaudhry wrote:
Hi,
I have created an MDB which does the following when a message is received from the queue.
1. Store message in database
2. do some processing
At step 1, if there is any issue with the database connection (e.g. database is not available etc), I rollback transaction. My idea is to leave the message on queue for now and retry it again after some time unless the database is back again. "Maximum retries" of the listener port is set to N but since there is no retry interval available, all N retries are done in a flash and my listener port stops working. I cannot use backout mechanism as I have to wait for the database to be back again. What are my options?i believe you need an XA driver and a transaction manager, for starters.
a simple JDBC rollback won't do it.
which app server are you using?
which jms provider?
%

HP Pavilion dv6 All 4 USB ports stopped working

Hello,
I recently bought a Pavilion dv6-6c11sa laptop. Windows 7 Home Premium 64-bit
Everything was working fine for about a week, and then yesterday all of the USB ports stopped working. I have 4 USB ports in total, two 2.0 and two 3.0. No matter what peripheral device I plug in, mouse or flash drive etc, they're not recognized by the laptop. The lights don't even light up on the devices, regardless of the port. I've tried uninstalling and reinstalling the drivers in device manager, taking out the battery and rebooting, installing the chipset drivers (AMD), nothing works. No programs had been installed 3 days prior to the occurence, although I had rebooted several times in that time frame. I simply booted up the laptop yesterday, and nothing worked.
Could anyone offer a solution or suggestion, please?

Hello,
I recently bought a Pavilion dv6-6c11sa laptop. Windows 7 Home Premium 64-bit
Everything was working fine for about a week, and then yesterday all of the USB ports stopped working. I have 4 USB ports in total, two 2.0 and two 3.0. No matter what peripheral device I plug in, mouse or flash drive etc, they're not recognized by the laptop. The lights don't even light up on the devices, regardless of the port. I've tried uninstalling and reinstalling the drivers in device manager, taking out the battery and rebooting, installing the chipset drivers (AMD), nothing works. No programs had been installed 3 days prior to the occurence, although I had rebooted several times in that time frame. I simply booted up the laptop yesterday, and nothing worked.

USB Ports Stopped working on MacBook Pro 13-inch, Late 2011, OS X 10.8.5

Please help with any advice
I have OS X 10.8.5
One USB port stopped a while ago
The other stopped yesterday.
I have reset the PRAM
I have also reset the SMC
Nothing seems to fix it.
I do have a time machine backup
Any suggestions?

The best option is a visit to the Apple store genius bar for a FREE evaluation. You have tried all you can.
Ciao.

A barcode scanner that was connected directly to the Mac's USB port stopped working as the "USB had too much power drawn", even though it has worked for over a year in that port. WHen we plugged it into the port on the keyboard, the device works. Why?

A barcode scanner that was connected directly to the Mac's USB port stopped working as the "USB had too much power drawn", even though it has worked for over a year in that port. When we plugged it into the port on the keyboard, the device works. Why? Obviously the device is operational. Could the USB port have burned out from having too much power drawn? If so, is it reparable?

It can't draw "too much" power, it can only draw as much as the USB port is able to provide and no more. IIRC, the keyboard port has a lower power output than the iMac's port.
That being said, yea, it's possible that the port has failed and it can be replaced or if another port works you can use that one. Although if it is still under warranty or covered by Apple Care, then I would take it to an Apple Store or service provider to get the port repaired.

Ports stopped working.

I used to use port 8001 for a lot of things. Recently, the port stopped working. I triple checked all my router settings and port 8001 is still forwarded. I tried other ports. I rebooted. I tried shutting off my firewall. Nothing worked. I really need a port working for various things so I need some help. Tell me if you need any additional information and I'll tell you. Does anyone know what I should do??

Well, I did everything you said and I'm sure I did it right. No luck. I have a feeling that something else is going on here, but I'm not sure what I should do. Anyone have any ideas?

1 of 2 USB ports stopped working after 10.7.2 upgrade

I have the newest Macbook Pro. I upgraded to 10.7.2 today and immediately after, 1 of my 2 usb ports stopped working.   Thought it may be the cable, so I switched cables. Tried plugging in my iPhone, my portable drive and nothing.   Both work on the other port though.   Both ports worked fine before the update.
I've rebooted 4x.
Suggestions?

    Reset SMC.     http://support.apple.com/kb/HT3964
    Choose the method for:
    "Resetting SMC on portables with a battery you should not remove on your own".
If this does not help, contact Apple.
Genius Bar reservation
http://www.apple.com/retail/geniusbar/
Best.

One usb port stopped working today

One of my USB ports stopped working today. I think it may be related to Itunes update today. Has anyone else seen this recently? I restarted my computer - but that didn't help. I have a MacBook Pro - running Lion 10.7.5
Any suggestions? I saw one USB Hub when I went to Apple --> About this Mac, but couldn't tell if both were there.

http://www.ehow.com/how_7351075_reset-usb-ports-mac-laptops.html

Brand new Macbook pro one USB port stopped working

Brand new Macbook Pro 15 with Retina display. One of the USB ports stopped working after 24hours.

Serial Port Configuration and Port definition is reset by
NVRAM http://support.apple.com/kb/ht1379
If no good I would return the machine ASAP:
Genius reservation http://www.apple.com/retail/geniusbar/
check warranty https://selfsolve.apple.com/agreementWarrantyDynamic.do

HT1379 MacBook Pro USB port stopped working

USB port stopped working....
How can I diagnose my USB port to test for hardware or software problem

Try Resetting the System Management Controller (SMC)

USB ports stopped working in my Macbook Pro

USB ports stopped working in my Macbook Pro

I do not know anything about audio consoles nor do I have an iPhone.
My iPod also does not show on the desktop but it is recognized in iTunes, Check if that is the case for your MBP.
Do you have the appropriate boxes checked in Finder Preferences?
See if this support article is of any assistance:
http://support.apple.com/kb/TS1410
If you have an external HDD, connect it to your MBP and see if it is recognized. If it does not show on the desktop, check Disk Utility.
Have you tried all USB ports? It could be that the problem lies in your MBP.
Ciao.

Satellite R830 - USB3.0 port stop working after long time usage

Hi there,
This is my new laptop. I got it just one week. However, USB 3.0 port is very weird. It always stop working when i used it for several hours. I try to update the driver, but i still seems not working.
are there any other solutions?

>well, it will stop working as well when i use it as data transfer.
So how long does it take until the USB 3.0 port stops working?
Does it interrupt the data throughput?
Did you use the USB 3.0 compatible devices?
On the Toshiba European driver page you can find the USB 3.0 driver version 2.0.34.1.
Are u using this version?

My USB ports stopped working. So did my dvd drive. I have a Pavillion Laptop. Model 1245dx.

My USB ports stopped working. Do did my DVD drive. I did do a Windows update yesterday. Any ideas out there? I can't use my mouse or printer. Help!

Try a windows system restore, pick a date before the windows updates were installed.

MAC PRO Internal USB ports stopped working

Hello, I have a mac pro 8 core with an USB internal ports problem, the 2 in front are not working anymore, and from the 3 in the back only the middle one is working.
I tried to pull all the power out for a whole night, resetting the pram and nvram but nothing helps.
When for example I put in a keyboard in one of the ports that is not working and when I power up the machine and I press the ALT key I get the choice of startup preferences, once I select one, and the system boots up the ports stops working, so before the OS loads the usb ports are working !!!
What to do ??

This is a hardware failure. While USB ports on the whole are just not designed very well, leading to their failures being pretty common, your issue sounds a bit more like the USB controller chip is failing.
In any case, the answer is to take it to a repair shop. If they're smart about it, they'll replace the logic board and see if that also fixes the front ports. If not, they'll replace the front I/O panel as well.

Re: Computer shuts down by itself, ethernet port stopped working (MS-7673 P67A-C45)

do a properties on each device with yellow mark and check its Hardware IDs

if the load temps are OK, try with a different PSU [quality one]
QuoteWindows tells me that Ethernet adapter is OK, but that no cable are connected. (It is!).
ethernet port stopped working
this suggest that board can be failing

HT2844 iMac 27"(late 2009), Audio in/Optical digital audio out port, stopped recognizing my new Bose speaker system, previously working...

Hello,
My iMac 27"(late 2009), Audio in/Optical digital audio out port, stopped recognizing my new Bose speaker system, previously working through that port. I tested the speaker system through my iPhone, and it works fine. I hooked it up to the Headphone out/Optical digital audio in port, and it works through that port also. I did a computer restart, I also checked all wiring and did a system repair on the computer. I also restarted the computer in mode where I could use the system utility, and the computer still did not correct the matter, and it reported everything as being "ok". I wented into "sound", through system preferences, and the computer does not recognize anything I plug into the Audio in/Optical digital audio out port. When I plug the speaker sysytem into the headphone out/optical digital audio out port, it does recognize the Bose speaker system as being "headphones".
Reading through a lot of forums, I hear everything from compatibility, to the port being stuck, and on and on. Since the port was working before, and just quit working one day, I wonder if there is a capacitor or fuse or some type of similar thing is blown, and causing the port to be unfunctionable. Maybe the port went bad, but before this time, I had never used it, and the computer does not move around, and I never plug in and pull wiring out unless needing to, and that being rare.
Here is a link to Costco, where I bought the system, and the exact system I have, if this is any help: http://accessories.us.dell.com/sna/productdetail.aspx?c=us&l=en&s=bsd&cs=04&sku= A4092931&ST=pla&dgc=ST&cid=262075&lid=4742361&acd=1230980794501410
By the way, I am running OS X Mountain Lion (10.8.5). I upgraded to Mavericks about a month ago, and expeirienced a number of issues, and had to take my iMac into Apple. Talking with the tech, I decided to wait for a while more before I upgraded to Mavericks. I try and keep the computer maintained.
If any of you have any ideas regadrding wear and tear, and fix I can do, etc., besides having to take my computer into Apple? Thank you, and potentially all of you, for your time and effort in helping me with this issue. Thank you kindly.
davE

Okay, davE, first, you have posted in the "Mac Pro" forum (not Macbook Pro), so we can't be super helpful
but we help you. First, hold down the Option key while clicking on the speaker icon at the top of your screen. This should show you all the inputs and outputs you have. you could check in "About this Mac" then "More info" to see whatever's recognized. Then, maybe, fire up Audio MIDI. your speaker system should show up there. something might have gotten set incorrectly. You can test it there. I guess you are using the good ol' analog cable for connection, and it works on your iPhone, so the cable isn't bad. You could try this. it 's an adapter which might solve your problem
http://www.amazon.com/gp/product/B004HBWYQ6/ref=oh_details_o00_s00_i00
depending on which model of Bose speaker you have, you might try doing a product reset
turn off speakers...unplug power cord from outlet...wait 1 minute..plug cord into outlet..turn on speakers..
\\turning off automatic standby||
press and hold top of control pod for 6 seconds until you hear 2 tones that go from high to low
other than that ,I don't know
John B

Port Stopped: Y

Similar Messages

Maybe you are looking for