Portal Design - Best Practices for Role and Workset Tab Menu

We are looking to identify and promote best practices in SAP Portal Design.
First, is there a maximum number of tabs which should exist on the highest level tab menu, commonly called the role menu? Do a large number of tabs on this menu cause performance issues? Are there any other issues associated with a large number of tabs on this menu?
Second, can the workset tab menu be customized to be 2 lines of tabs? Our goal is to prevent tab scrolling.
Thanks

Debra,
Not aware of any performance issues with the number of tabs in the Level 1 or 2 menus, particularly if you have portal navigation caching enabled.
From an end user perspective I guess "best practice" would be to avoid scrolling in the top level navigation areas completely if possible.
You can do a number of things to avoid this, including:
- Keep the role/folder/workset names as short as possible.
- If necessary break the role down into multiple level 1 entry points to reduce the number of tabs in level 2.
An example of the second point would be MSS. Instead of creating a role with a single workset (i.e. level 1 tab), we usually split it into two folders called something like "My Staff" and My Finance" and define these folders as entry points. We therefore end up with two tabs in level 1 for the MSS role, and consequently a smaller number of tabs in level 2.
Hope that helps......
Regards,
John

Similar Messages

Best Practice for Planning and BI

What's the best practice for Planning and BI infrastructure - set up combined on one box or separate? What are the factors to consider?
Thanks in advance..

There is no way that question could be answered with the information that has been provided.
Cheers
John
http://john-goodwin.blogspot.com/

How can i get best practice for SD and MM

Please, can any body tell me how can i get best practices for SD and MM for functional approach?
Thanks
Utpal

Hello Utpal,
I am really surprised, in just 10 minutes you searched that site and found it not useful. Check out my previous reply "you will not find screen shot in this but you can add it in this"
You will not find readymade document, you need to add this as per your requirement.
btw, the following link gives you some more link for new SAP guys, this will be helpful. Check out HOW to BASIC transaction
New to Materials Management / Warehouse Management?
Hope this helps.
Regards
Arif Mansuri

Best practice for Plan and actual data

Hello, what is the best practice for Plan and actual data? should they both be in the same app or different?
Thanks.

Hi Zack,
It will be easier for you to maintain the data in a single application. Every application needs to have the category dimension, mandatorily. So, you can use this dimension to maintain the actual and plan data.
Hope this helps.

DNS best practices for hub and spoke AD Architecture?

I have an Active Directory Forest with a forest root such as joe.co and the root domain of the same name, and root DNS servers (Domain Controllers) dns1.joe.co and dns2.joe.co
I have child domains with names in the form region1.joe.com, region2.joe.co and so on, with dns servers dns1.region1.joe.co and so on.
Each region has distribute offices that may have a DC in them, servers named in the form dns1branch1.region1.joe.co
Over all my DNS tests out okay, but I want to get the general guidelines for setting up new DCs correct.
Configuration:
Root DC/DNS server dns1.joe.co adapter settings points DNS to itself, then two other root domain DNS/DCs dns2.joe.co and dns3.joe.co.
The other root domain DNS/DCs adapter settings point to root server dns1.joe.co and then to itself dns2.joe.co, and then 127.0.0.1
The regional domains have a root dns server dns1.region1.joe.co with adapter that that points to root server dns1.joe.co then to itself.
The additional region domain DNS/DCs adapter settings point to dns1.region1.joe.co then to itself then to dn1.joe.co
What would you do to correct this topology (and settings) or improve it?
Thanks in advance
just david

Hi,
According to your description, my understanding is that you need suggestion about your DNS topology.
In theory, there is no obvious problem. Except for the namespace and server plaining for DNS, zone is also needed to consideration. If you place DNS server on each domain and subdomain, confirm that if the traffic browsed by DNS will affect the network performance.
Besides, fault tolerance and security are also necessary.
We usually recommend that:
DC with DNS should point to another DNS server as primary and itself as secondary or tertiary. It should not point to self as primary due to various DNS islanding and performance issues that can occur. And when referencing a DNS server on itself, a DNS client
should always use a loopback address and not a real IP address. detailed information you may reference:
What is Microsoft's best practice for where and how many DNS servers exist? What about for configuring DNS client settings on DC’s and members?
http://blogs.technet.com/b/askds/archive/2010/07/17/friday-mail-sack-saturday-edition.aspx#dnsbest
How To Split and Migrate Child Domain DNS Records To a Dedicated DNS Zone
http://blogs.technet.com/b/askpfeplat/archive/2013/12/02/how-to-split-and-migrate-child-domain-dns-records-to-a-dedicated-dns-zone.aspx
Best Regards,
Eve Wang
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Universe Design Best Practices for Oracle

Hello All,
We recently moved from XIR2 on MS SQL 2005 to XI 3.1 on Oracle. This has been a difficult move for us as my team is new to oracle. I'm currently working on several performance issues between BOBJ and Oracle and am looking for documentation on best practices for universe design with oracle. I've foudn tidbits here and there regrading using parameters joing_by_sql and boundary_weight_table, wondering if there are other options out there that might help. We have queries taking 45+ minutes to run and that is totally unacceptable.
thanks
Andrea

I am not sure if you are looking for Optimization or anything else. sorry for that following link might help you considering Oracle as DB.
Link:[Universe Optimization 1|http://www.bidwtoday.com/business-objects/universe-designer/business-objects-universe-optimization/]
Link:[Universe Optimization 2|http://forums.sdn.sap.com/post!reply.jspa?messageID=8721932]
--Kuldeep

What are best practice for packaging and deploying j2EE apps to iAS?

We've been running a set of J2EE applications on a pair of iAS SP1b for about a year and it has been quite stable.
Recently however we have had a number of LDAP issues, particularly when registering and unregistering applications (registering ear files sometimes fails 1st time but may work 2nd time). Also We've noticed very occasionally that old versions of classes sometimes find their way onto our machines.
What is considered to be best practice in terms of packaging and deployment, specifically:
1) Packaging - using the deployTool that comes with iAS6 SP1b to package is a big manual task, especially when you have 200+ jsp files. Are people out there using this or are they scripting it with a build tool such as Ant?
2) Deploying an existing application to multiple iAS's. Are you guys unregistering old application then reregistering new application? Are you shutting down iAS whilst doing the deployment?
3) Deploying ear files can take 5 to 10 mins, is this normal?
4) In a clustered scenario where HTTPSession is shared what are the consequences of doing deployments to data stored in session?
thanks in asvance for your replies
Owen

You may want to consider upgrading your application server environment to a newer service pack. There are numerous enhancements involving the deployment tool and run time layout of your application that make clear where you're application is loading its files from.
If you've at a long running application server environment, with lots of deployments under your belt, you might start to notice slow downs in deployment and kjs start time. Generally this is due to garbage collecting in your iAS registry.
You can do several things to resolve this. The most complete solution is to reinstall the application server. This will guarantee a clean ldap registry. Of course you've got to restablish your configurations and redeploy your applications. When done, backup your application server install space with the application server and directory server off. You can use this backup to return to a known configuation at some future time.
For the second method: BE CAREFUL - BACKUP FIRST
There is a more exhaustive solution that involves examining your deployed components to determine the active GUIDS. You then search the NameTrans section of the registry searching for Applogic Servlet *, and Bean * entries that represent your previously deployed components but are represented in the set of deployed GUIDs. Record these older GUIDs, remove them from ClassImp and ClassDef. Finally remove the older entries from NameTrans.
Best practices for deployment depend on your particular environmental needs. Many people utilize ANT as a build tool. In later versions of the application server, complete ANT scripts are included that address compiling, assembly and deployment. Ant 1.4 includes iAS specific targets and general J2EE targets. There are iAS specific targets that can be utilized with the 1.3 version. Specialized build targets are not required however to deploy to iAS.
Newer versions of the deployment tool allow you to specify that JSPs are not to be registered automatically. This can be significant if deployment times lag. Registered JSP's however benefit more fully from the services that iAS offers.
2) In general it is better to undeploy then redeploy. However, if you know that you're not changing GUIDs, recreating an existing application with new GUIDs, or removing registered components, you may avoid the undeploy phase.
If you shut down the KJS processes during deployment you can eliminate some addition workload on the LDAP server which really gets pounded during deployment. This is because the KJS processes detect changes and do registry loads to repopulate their caches. This can happen many times during a deployment and does not provide any benefit.
3) Deploying can be a lengthy process. There have been improvements in that performance from service pack to service pack but unfortunately you wont see dramatic drops in deployment times.
One thing you can do to reduce deployment times is to understand the type of deployment. If you have not manipulated your deployment descriptors in any way, then there is no need to deploy. Simply drop your newer bits in to the run time space of the application server. In later service packs this means exploding the package (ear,war, or jar) in to the appropriate subdirectory of the APPS directory.
4) If you've changed the classes of objects that have been placed in HTTPSession, you may find that you can no longer utilize those objects. For that reason, it is suggested that objects placed in session be kept as simple as possible in order to minimize this effect. In general however, is not a good idea to change a web application during the life span of a session.

Best practice for PK and indexes?

Dear All,
What is the best practice for making Primary Key and indexes? Should we keep them in the same tablespace as table or should we create a seperate tableapce for all indexes and Primary Key? Please note I am talking about a table that has 21milion rows at the moment and increasing 10k to 20k rows daily. This table is also heavily involved in daily reports and causing slow performance. Currently the complete table with all associated objects such as indexes and PK is stored in one seperate tablespace. If my way is right then please advise me how can I improve the performance of retrival or DML operation on this table?
Thanks in advance..
Zia Shareef

Well, thanks for valueable advices... I am using Oracle 8i and let me tell you exact problem...
My billing database has two major tables having almost 21 millions rows each... one has collection data and other one for invoices... many reports are showing the data with the joining of Customer + Collection + Invoices tables.
There are 5 common fields in between invoices(reading) and collection tables
YEAR, MONTH, AREA_CODE, CONS_CODE, BILL_TYPE(adtl)
My one of batch process has following update and it is VERY VERY SLOW:
UPDATE reading r
SET bamount (SELECT sum(camount)
FROM collection cl
WHERE r.ryear = cl.byear
AND r.rmonth = cl.bmonth
AND r.area_code = cl.area_code
AND r.cons_code = cl.cons_code
AND r.adtl = cl.adtl)
WHERE area_code = 1
tentatively area_code(1) is having 20,000 consumers
each consuemr may have 72 invoices and against these invoices it may have 200 rows in collection tables (system have provision to record partial payment against one invoice)
NOTE: Please note presently my process is based on cursors so the above query runs for one consumer at one time but just for giving an idea I have made it for whole area.
Mr. Yingkuan, can you please tell me how can I check that the table' statistics is not current and how can I make it current. Is it really effect performance?

Kernel: PANIC! -- best practice for backup and recovery when modifying system?

I installed NVidia drivers on my OL6.6 system at home and something went bad with one of the libraries. On reboot, the kernel would panic and I couldn't get back into the system to fix anything. I ended up re-installing the OS to recovery my system.
What would be some best practices for backing up the system when making a change and then recovering if this happens again?
Would LVM snapshots be a good option? Can I recovery a snapshot from a rescue boot?
EX: File system snapshots with LVM | Ars Technica -- scroll down to the section discussing LVM.
Any pointers to documentation would be welcome as well. I'm just not sure what to do to revert the kernel or the system when installing something goes bad like this.
Thanks for your attention.

There is often a common misconception: A snapshot is not a backup. A snapshot and the original it was taken from initially share the same data blocks. LVM snapshot is a general purpose solution which can be used, for example, to quickly create a snapshot prior to a system upgrade, then if you are satisfied with the result, you would delete the snapshot.
The advantage of a snapshot is that it can be used for a live filesystem or volume while changes are written to the snapshot volume. Hence it's called "copy on write (COW), or copy on change if you want. This is necessary for system integrity to have a consistent data status of all data at a certain point in time and to allow changes happening, for example to perform a filesystem backup. A snapshot is no substitute for a disaster recovery in case you loose your storage media. A snapshot only takes seconds, and initially does not copy or backup any data, unless data changes. It is therefore important to delete the snapshot if no longer required, in order to prevent duplication of data and restore file system performance.
LVM was never a great thing under Linux and can cause serious I/O performance bottlenecks. If snapshot or COW technology suits your purpose, I suggest you look into Btrfs, which is a modern filesystem built into the latest Oracle UEK kernel. Btrfs employs the idea of subvolumes and is much more efficient that LVM because it can operate on files or directories while LVM is doing the whole logical volume.
Keep in mind however, you cannot use LVM or Btrfs with the boot partition, because the Grub boot loader, which loads the Linux kernel, cannot deal with LVM or BTRFS before loading the Linux kernel (catch22).
I think the following is an interesting and fun to read introduction explaining basic concepts:
http://events.linuxfoundation.org/sites/events/files/slides/Btrfs_1.pdf

Best Practice for SUP and WSUS Installation on Same Server

Hi Folks,
I have a question, I am in process of deploying SCCM 2012 R2... I was in process of deploying Software Update Point on SCCM with one of the existing WSUS server installed on a separate server from SCCM.
A debate has started with of the colleague who says that the using remote WSUS server is recommended by Microsoft because of the scalability security that WSUS will be downloading the updates from Microsoft and SCCM should be working as downstream
server to fetch updates from WSUS server.
but according to my consideration it is recommended to install WSUS server on the same server where SCCM is installed... actually it is recommended to install WSUS on a site system and you can used the same SCCM server to deploy WSUS.
please advice me the best practices for deploying SCCM and WSUS ... what Microsoft says about WSUS to be installed on same SCCM server OR WSUS should be on a separate server then the SCCM server ???
awaiting your advices ASAP :)
Regards, Owais

Hi Don,
thanks for the information, another quick one...
the above mentioned configuration I did is correct in terms of planning and best practices?
I agree with Jorgen, it's ok to have WSUS/SUP on the same server as your site server, or you can have WSUS/SUP on a dedicated server if you wish.
The "best practice" is whatever suits your environment, and is a supported-by-MS way of doing it.
One thing to note, is that if WSUS ever becomes "corrupt" it can be difficult to repair and sometimes it's simplest to rebuild the WSUS Windows OS. If this is on your site server, that's a big deal.
Sometimes, WSUS goes wrong (not because of ConfigMgr)..
Note that if you have a very large estate, or multiple primary site servers, you might have a CAS, and you would need a SUP on the CAS. (this is not a recommendation for a CAS, just to be aware)
Don
(Please take a moment to "Vote as Helpful" and/or "Mark as Answer", where applicable.
This helps the community, keeps the forums tidy, and recognises useful contributions. Thanks!)

Best Practices for AD and Windows Environment

Hello Everyone,
I need to create a document having the best practices for AD containing best practices for DNS, DHCP, AD Structure, Group Policy, Trust Etc.
I just need the best practices irrespective of what is implemented in our company.
I just need to create a document for analysis as of now. I searched over the internet but could not find much. I would request you all to pour in your suggestions from where i can find those.
If anyone could send me or point me the link. I am pretty new to the technology, so need your help.
Thanks in Advance

I have an article where I shared the best practices to use to avoid known AD/DNS issues: http://www.ahmedmalek.com/web/fr/articles.asp?artid=23
However, you need first to identify your requirements and based on these requirements, you can identify what should be implemented on your environment and how to manage it. The basics here is that you need to have at least two DC/DNS/GC servers per AD domain
for the High Availability. You need also to take a system state backup of at least one DC/DNS/GC server in your domain. As for DHCP, you can use 50/50 or 80/20 DHCP rule depending on your setup.
You can also refer to that: https://technet.microsoft.com/en-us/library/cc754678%28v=ws.10%29.aspx
This posting is provided AS IS with no warranties or guarantees , and confers no rights.
Ahmed MALEK
My Website Link
My Linkedin Profile
My MVP Profile

Export and Deployment - Best Practices for RAR and CUP

Hi Experts,
I wanted to know what in your opinon is best practice for deployment for GRC for a 3 system landscape.
We have a development landscape which connacts to all our environments - Dev-QA-Prod.
Is it recommended to have just the production client connected to the prodiction boxes only and use Dev/ QA for other environments or is it a good idea to have Prod and QA in sync?
In my opinion it looks like a good idea to have the same QA and PROD as it would make export easier.. Maybe I am worng..
What according to you all is a good recommended practice here?
Thanks,
Chinmaya

Hi Chinmaya,
depends how many clusters you have in your landscape
if it is something like 5 DEV box to connect 5 QAS boxes, so on
then best practice will be to have separate DEV - QAS - PRD boxes for GRC if money (h/w ) is no constraint for organization
rather than later asking SAP for deletion scripts for deleting sandbox or dev connectors,
best to have separate boxes for each
also for future whenever you do rule changes in RAR and config changes in CUP, best to test in QAS first, as CUP will become very critical for your organization, post go-live
and good part will be that management report will reflect true data for PRD only
regards,
Surpreet

Best practice for declaring and initializing String?

What is the best practice for the way Strings are declared in a class?
Should it be
private String strHello = "";
or should I have the initialization in the constructors?

The servlet constructor is usually called once, when the servlet is first accessed. But then again maybe something else happens, google servlet life cycle if you must know.
But let's take a step backwards here. It seems like you are trying to put fields into servlets. Don't do that. When two users fetch the servlet's URL at the same time, the fields are shared between the two hits. If you store something like HTTP parameters in the fields, the two hits' parameters will get mangled. The hits can end up seeing each other's parameter values.
The best way is not to have fields in servlets. (Except maybe "static final" constants, sometimes rarely something else.) Many concurrency worries go away, servlet life cycle worries go away, servlet constructors go away, init() usually goes away.

Wireless Design - Best Practices for Data, Voice, and LBS

Hi,
I am currently in the process of designing a WLAN for a new hospital and I am getting some push back from my sales team. The requirements of the WLAN are data, voice, and location based services (RFID for medical equipment) ... needs to be 2.4 GHz for Guest and some apps/clients but primarily 5 GHz for most of the clients ... lastly needs to be N compatible for future use.
So, I did a predictive design with 1252's on the perimeter with 2.4 and 5 GHz patch antennas and 1142's in the middle to fill gaps ... I also scoped out 2 5508 for redundancy .... total design with -65 at my edges was 169. However, this is getting push back because of several cost issues ....
1. The bundle that Cisco offers for 5 100 AP license 5508 WLC is cheaper than buying 2 250 AP licenses WLC's ... which doesn't make any sense to me because I think 5 devices is over kill
2. The sales engineer is concerned about the power issues with the 1252's ... customer would rather not use power injectors ... and although they would have 6500's at there core ... they would only have basic switches in their IDF's so I wasn't sure which POE Switches would be able to handle 1252 but cost was an issue there as well
So, for my understanding when you are doing a WLAN design for LBS it's always best to have APs or antennas on the perimeter for better triangulation ... it makes more sense to me to do that with patch instead of Omni's ... however my sales engineer wants to use all 1142's ... so my question is what are the pro and cons behind using all Omni's or using Patch and Omni's?
Furthermore, if anyone has any documentation supporting why I would not use all Omni's that would be great because all the articles I have read on LBS just state that placement of APs is critical but doesn't give no specifics on whether it's a good practice to place them on the perimeter using a specific type of antenna or what.
Thanks in advance for you help and any ideas about this design!!!

1. The 5508 is expensive because it's alot faster than the 4400 plus there are some features exclusive to the 5508 such as OfficeExtend. As the old network design adage goes: Your design can be done correctly, cheap or fast. Choose two.
2. The 1250 requires 19.5w of power to enable FULL MCS rates to both radios. Only the 3560E, 3750E or the Sup720 is capable of supporting that. Upgrading the IOS of the 1250 to 12.4(10b)JDA3 will allow the AP to operate both radios at 15.4w BUT at a lower MCS rates. Correct placement of the AP and the correct use of the antennaes will also help in the signal distribution.
3. Patch antennaes are mostly directional. The 1140 is onmi-directional BUT the signal strength is not as powrful as the 1250 at full power. The AIR-ANT2451NV is an omni-directional patch designed for the 1250.
Cisco Aironet Antennas and Accessories Reference Guide
http://www.cisco.com/en/US/prod/collateral/wireless/ps7183/ps469/product_data_sheet09186a008008883b.html
Cisco Aironet 2.4 GHz and 5 GHz Antennas and Accessories
http://www.cisco.com/en/US/prod/collateral/wireless/ps7183/ps469/product_data_sheet09186a008022b11b.html
Some of the new patch antennaes for the 1250
Cisco Aironet Dual Band MIMO Low Profile Ceiling Mount Antenna (AIR-ANT2451NV-R)
http://www.cisco.com/en/US/prod/collateral/wireless/ps7183/ps469/data_sheet_ant2451nv.pdf
Cisco Aironet Very Short 5-GHz Omnidirectional Antenna (AIR-ANT5135SDW-R)
http://www.cisco.com/en/US/prod/collateral/wireless/ps7183/ps469/data_sheet_ant5135sdw.pdf
Cisco Aironet Very Short 2.4-GHz Omnidirectional Antenna (AIR-ANT2422SDW-R)
http://www.cisco.com/en/US/prod/collateral/wireless/ps7183/ps469/data_sheet_ant2422sdw.pdf
Cisco Aironet 5-dBi Diversity Omnidirectional Antenna (AIR-ANT2452V-R)
http://www.cisco.com/en/US/prod/collateral/wireless/ps7183/ps469/data_sheet_ant2452v.pdf
Cisco Aironet 5-GHz MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT5140NV-R)
http://www.cisco.com/en/US/prod/collateral/wireless/ps7183/ps469/data_sheet_ant5140nv.pdf
Cisco Aironet 5-GHz MIMO 6-dBi Patch Antenna (AIR-ANT5160NP-R)
http://www.cisco.com/en/US/prod/collateral/wireless/ps7183/ps469/data_sheet_ant5160np.pdf
Cisco Aironet 2.4-GHz MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2450NV-R)
http://www.cisco.com/en/US/prod/collateral/wireless/ps7183/ps469/data_sheet_ant2450nv.pdf
Cisco Aironet 2.4-GHz MIMO 6-dBi Patch Antenna (AIR-ANT2460NP-R)
http://www.cisco.com/en/US/prod/collateral/wireless/ps7183/ps469/data_sheet_ant2460np.pdf

Resources for from design - best practices for layout?

Hi,
I have made a number of forms fo the past few years. I feel like they look dated and are somewhat stale... I have found a few resources out there on Javascript best practices and more mechanical focused articles, but nothing really specific design as it relates to usability and "feel". I realized some of this is subjective and varies depending on the form's purpose, but I am just looking for some new ideas.
Does anyone have a resource or listing of froms they think are outstanidng from a design perspective?
Is anyone willing to share forms they think are outstanding? Just that baisics like information collection?
How much color and line type objects become to much?
What are some design elements used in "web 2.0" (whatver that really means) that we sould be using in our forms. tempered with what can be done.
I am looking for this to be an open disucssion and am curious to hear what works for others. I hope others will find this interesting and helpful.
Cheers,
Tom

And the second snippet code validates any form to check every fields if values are not null, if a value is null it will setFocus on the first null field
2. Validate Form and Focus on First Field that Fails Validation
 2.1 Create a script Object with two small methods to return a table of fields that have null values
Script Object :
form1.#variables[0].myForm - (JavaScript, client)
//Tab for field's expressions and field's exceptions
var tabExpression;
var tabException;
function validateAllFields(rootObject){
 //If a field is null, stop everything
 if (tabExpression.length > 0)
 return;
 //If the 'presence' property is by default 'visible' in the form and the object value is 'visible', the 'presence' property doesn't exist
 //If its default value is "hidden", the property always exist
 if (!rootObject.isPropertySpecified("presence") || rootObject.presence == "visible"){
 //Verify if the object contains an interface 'button'
 //The button is considered as a 'field', so if it's not a button the statement is true
 if (!(rootObject.isPropertySpecified("ui") && rootObject.ui.nodes.item(0).className == "button")){
 //If the object contains nodes and if it's not a 'field' or a RadioButtonList
 if (rootObject.nodes.length > 0 && (rootObject.className != "field" && rootObject.className != "exclGroup")){
 //Recall this method for each nodes in the object to find every fields (Recursive Method)
 for (var i = 0; i < rootObject.nodes.length; i++){
 validateAllFields(rootObject.nodes.item(i));
 //Verify to add the object in the list if the object is a field and if it contains a value
 if (rootObject.className == "field" || rootObject.className == "exclGroup"){
 if (rootObject.rawValue == null || rootObject.rawValue == 0){
 //Variable to determines if the object is an exception field
 var boValidate = true;
 //If there's exception fields
 if (tabException.length > 0){
 //Verify if the field is in the exception list
 if (tabException.indexOf(rootObject.name) != -1){
 boValidate = false;
 //Add if the object is not in the exception table
 if (boValidate)
 tabExpression[tabExpression.length] = rootObject.somExpression;
 2.2 Create this method in your object as well, and will be called on a click_event
function getValExpressions(rootObject, tabExcption){
 //Create new table
 tabExpression = new Array();
 //Put the exceptions fields value in the exception table
 tabException = tabExcption
 //Validation
 validateAllFields(rootObject);
 //Return a null field
 return tabExpression;
 2.3 The click event is where you write the special validation for different forms
//Create a table with exception fields, can be used for special validation fields or no validation
var tabExceptionFields = new Array("dateField1", "txtComments", "txtTotal");
//Call the validation
var tab = myForm.getValExpressions(Main, tabExceptionFields);
if (tab.length > ){
 xfa.host.setFocus(tab[0]);
} else{
 var boValidate = false;
 var strExpression;
 //write your validation according to the fields you need special validation.
 if (statement == false){
 strExpression = Reference_Syntax.Field.somExpression;
 boValidate = false;
 if (boValidate){
 xfa.host.print(1, "0", (xfa.host.numPages -1).toString(), 0, 0, 0, 0, 0);
 } else{
 xfa.host.setFocus(strExpression);
I will post a form template as an exemple for these function
Enjoy!
Message was edited by: Magus069

Portal Design - Best Practices for Role and Workset Tab Menu

Similar Messages

Maybe you are looking for