Portal down after starting Server in debug mode

I have started my AS Java in Debug Mode. Now, the Portal is down, shing the following error message:
503 Service not available
Error:     -6
Version:     7010
Component:     ICM Java
Date/Time:     Mon May 26 11:39:28 2008
Module:     http_j2ee2.c
Line:     1136
Server:     SV-SAP-5_CES_01
Error Tag:     {00000a45}
Detail:     ICM running but no server with HTTP connected - Load Balancing failed
Why is that?
Thanks, JJJ

It takes time till the server is running again. Wait a few minutes and try again!

Similar Messages

Starting Server in Debug Mode - Need Some Advice Plz.

Hi Guys,
I have an EP SP 12 Server Running and I am trying to Start the Server in Debug mode from the Netweaver Developer Studio but when I right click the Server and try to choose Debug, the option is greyed out and even while viewing the Debug option from the SAPMMC I see that under the column Debug, it say 'Disabled' for the Server and Dispatcher.
Can anyone suggest how this can be done, I would appreciate any help as I have been working on this for some time.
Best Wishes,
John.
Message was edited by: John Bray
Message was edited by: John Bray

Hi John,
If the you cannot start the server in the debugging mode through the NWDS then you can try the other way round.
Through Config Tool:
You can enable the debuggine mode from the Config Tool as well. Just visit the following path :
C:\usr\sap\<SID>\JC<SYS_NO>\j2ee\configtool\configtool.bat
Click on the your instance. Then under the tab VM Environment, Set the DebugMode = true.
Restart the engine now. This will open the J2EE server again in the Debug Mode.
I hope this helps you!!
Regards
Pravesh
PS: Please conside rewarding points if helpful and solved.

How to start server in debug mode by default

Hi,
Whenever the server starts it does not start in debug mode.
One has to manually start the "SDM" and "Server0" in the debug mode.
Is there a way I can make the server start in debug mode for the first time itself.
regards,
Saurabh

Hi Saurabh,
You can start the server in debug mode using config tool. Just open cofig tool (/usr/sap/<SYS ID>/JC<SYS NR>/j2ee/configtool/configtool.bat).
Click on the your instance. Then under the tab Servers Debug check Debuggable and also Enable Debug mode.
Restart the engine now.
However a word of caution: Starting the server in debug mode decreases the system performance. You should only start the dev server in debug mode.
Hope this helps.
Regards
Sidharth

Starting SOA Suite server in debug mode

Hello,
anyone knows how to start soa suite server on debug mode?
it basically oc4j server started from opmn. is there anyway i can pass the "-ojvm -XXdebug,port4000,detached,quiet" to opmn?
Rudi

solved..!!!
http://download.oracle.com/docs/cd/B31017_01/web.1013/b28950/sysprops.htm#CHDCFADJ

Start weblogic server in debug mode through command prompt

Hi,
Please help me in starting the weblogic server in debug mode through command prompt.I am using weblogic 10.3.6 app server.
Thanks

Hi,
To debug weblogic startup issues you can pass the below jvm arguments:
-Dweblogic.slc=true
-Dweblogic.debug.DebugServerLifeCycle=true
Debug options are available in weblogic based on the subsystem, such as security, jms, jdbc, deployment..etc
You can refer to :
https://blogs.oracle.com/vijaya/entry/weblogic_web_service_debug_flags
Thanks,
Sharmela

How to start weblogic in debug mode ? and how to set the eclipse in the deb

how to start weblogic in debug mode ? and how to set the eclipse in the debug

Put this in JAVA_OPTIONS :
Xdebug -Xnoagent -Djava.compiler=NONE -Xrunjdwp:transport=dt_socket,address=3999,suspend=y,server=y
After restarted weblogic, in eclipse set your breakpoint , open debug perspective then choose Remote Java Appliction and configure Connection Properties (host=localhost and port=3999)

Error when starting Weblogic in debug mode

Hi there
Has anyone experienced any difficulties when starting weblogic in debug mode.
More specifically, it cannot start correctly because it thinks that another instance
is using the same port (definately not the case).
Any clues/suggestions are greatly appreciated.
Error log follows:
<Mar 18, 2002 7:42:32 AM GMT+10:00> <Emergency> <WebLogicServer> <Unable to create
a server socket for port: 8320. java.net.BindException: Address already in use
Perhaps another process is using port 8320.>
<Mar 18, 2002 7:42:32 AM GMT+10:00> <Notice> <WebLogicServer> <SSLListenThread
listening on port 8321>
<Mar 18, 2002 7:42:32 AM GMT+10:00> <Emergency> <WebLogicServer> <The WebLogic
Server is no longer listening for connections. You should probably restart it.>
<Mar 18, 2002 7:42:32 AM GMT+10:00> <Alert> <WebLogicServer> <Server shutdown
has been requested by system>
<Mar 18, 2002 7:42:32 AM GMT+10:00> <Alert> <WebLogicServer> <The shutdown sequence
has been initiated.>
<Mar 18, 2002 7:42:32 AM GMT+10:00> <Info> <WebLogicServer> <Server shutdown is
commencing NOW and is irreversible.>
<Mar 18, 2002 7:42:32 AM GMT+10:00> <Error> <Performance Pack> <Unable to load
performance pack, using Java I/O.
java.lang.ThreadDeath
at java.lang.Thread.stop(Thread.java:581)
at weblogic.t3.srvr.T3Srvr.die(T3Srvr.java:764)
at weblogic.t3.srvr.T3Srvr.waitForDeath(T3Srvr.java:507)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:171)
at weblogic.Server.main(Server.java:35)

Thanks for the suggestion.
Unfortunatley the port is definately free/available during startup.
Stephane Kergozien <[email protected]> wrote:
Maark,
Before starting your server, please could you check that the port is
not used by one
other process. You can use the netstat command to do this.
Regards
Stephane
Mark wrote:
Hi there
Has anyone experienced any difficulties when starting weblogic in debugmode.
More specifically, it cannot start correctly because it thinks thatanother instance
is using the same port (definately not the case).
Any clues/suggestions are greatly appreciated.
Error log follows:
<Mar 18, 2002 7:42:32 AM GMT+10:00> <Emergency> <WebLogicServer> <Unableto create
a server socket for port: 8320. java.net.BindException: Address alreadyin use
Perhaps another process is using port 8320.>
<Mar 18, 2002 7:42:32 AM GMT+10:00> <Notice> <WebLogicServer> <SSLListenThread
listening on port 8321>
<Mar 18, 2002 7:42:32 AM GMT+10:00> <Emergency> <WebLogicServer> <TheWebLogic
Server is no longer listening for connections. You should probablyrestart it.>
<Mar 18, 2002 7:42:32 AM GMT+10:00> <Alert> <WebLogicServer> <Servershutdown
has been requested by system>
<Mar 18, 2002 7:42:32 AM GMT+10:00> <Alert> <WebLogicServer> <The shutdownsequence
has been initiated.>
<Mar 18, 2002 7:42:32 AM GMT+10:00> <Info> <WebLogicServer> <Servershutdown is
commencing NOW and is irreversible.>
<Mar 18, 2002 7:42:32 AM GMT+10:00> <Error> <Performance Pack> <Unableto load
performance pack, using Java I/O.
java.lang.ThreadDeath
at java.lang.Thread.stop(Thread.java:581)
at weblogic.t3.srvr.T3Srvr.die(T3Srvr.java:764)
at weblogic.t3.srvr.T3Srvr.waitForDeath(T3Srvr.java:507)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:171)
at weblogic.Server.main(Server.java:35)--
Regards,
Stephane Kergozien
BEA Support

Start weblogic in debug mode

Hi,
I want to start weblogic in debug mode.
Do you know what modifications should be made in the default configurations?
-John

John wrote:
Hi,
I want to start weblogic in debug mode.
Do you know what modifications should be made in the default configurations?
-JohnWebLogic Server doesn't have a debug mode. Are you trying to see debug
messages in the shell window where you started the server?
~Ryan

Help! Starting Weblogic in Debug Mode

Hi there
Any clues/suggestions are greatly appreciated.
Has anyone experienced any difficulties when starting weblogic in debug mode.
More specifically, it cannot start correctly because it thinks that another instance
is using the same port (definately not the case).
Error log follows:
<Mar 18, 2002 7:42:32 AM GMT+10:00> <Emergency> <WebLogicServer> <Unable to create
a server socket for port: 8320. java.net.BindException: Address already in use
Perhaps another process is using port 8320.> <Mar 18, 2002 7:42:32 AM GMT+10:00>
<Notice> <WebLogicServer> <SSLListenThread listening on port 8321> <Mar 18, 2002
7:42:32 AM GMT+10:00> <Emergency> <WebLogicServer> <The WebLogic Server is no
longer listening for connections. You should probably restart it.>
<Mar 18, 2002 7:42:32 AM GMT+10:00> <Alert> <WebLogicServer> <Server shutdown
has been requested by system> <Mar 18, 2002 7:42:32 AM GMT+10:00> <Alert> <WebLogicServer>
<The shutdown sequence has been initiated.> <Mar 18, 2002 7:42:32 AM GMT+10:00>
<Info> <WebLogicServer> <Server shutdown is commencing NOW and is irreversible.>
<Mar 18, 2002 7:42:32 AM GMT+10:00> <Error> <Performance Pack> <Unable to load
performance pack, using Java I/O. java.lang.ThreadDeath at java.lang.Thread.stop(Thread.java:581)
at weblogic.t3.srvr.T3Srvr.die(T3Srvr.java:764) at weblogic.t3.srvr.T3Srvr.waitForDeath(T3Srvr.java:507)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:171) at weblogic.Server.main(Server.java:35)

The following error has nothing to do with running in debug mode?
It just means that there's another process already binded to port 8320
you might want to see the output of netstat -a
BTW, what flags you switched on to run the server in debug mode?
Kumar
"Mark" <[email protected]> wrote in message
news:3c951474$[email protected]..
>
Hi there
Any clues/suggestions are greatly appreciated.
Has anyone experienced any difficulties when starting weblogic in debugmode.
More specifically, it cannot start correctly because it thinks thatanother instance
is using the same port (definately not the case).
Error log follows:
<Mar 18, 2002 7:42:32 AM GMT+10:00> <Emergency> <WebLogicServer> <Unableto create
a server socket for port: 8320. java.net.BindException: Address already inuse
Perhaps another process is using port 8320.> <Mar 18, 2002 7:42:32 AMGMT+10:00>
<Notice> <WebLogicServer> <SSLListenThread listening on port 8321> <Mar18, 2002
7:42:32 AM GMT+10:00> <Emergency> <WebLogicServer> <The WebLogic Server isno
longer listening for connections. You should probably restart it.>
<Mar 18, 2002 7:42:32 AM GMT+10:00> <Alert> <WebLogicServer> <Servershutdown
has been requested by system> <Mar 18, 2002 7:42:32 AM GMT+10:00> <Alert><WebLogicServer>
<The shutdown sequence has been initiated.> <Mar 18, 2002 7:42:32 AMGMT+10:00>
<Info> <WebLogicServer> <Server shutdown is commencing NOW and isirreversible.>
<Mar 18, 2002 7:42:32 AM GMT+10:00> <Error> <Performance Pack> <Unable toload
performance pack, using Java I/O. java.lang.ThreadDeath atjava.lang.Thread.stop(Thread.java:581)
at weblogic.t3.srvr.T3Srvr.die(T3Srvr.java:764) atweblogic.t3.srvr.T3Srvr.waitForDeath(T3Srvr.java:507)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:171) atweblogic.Server.main(Server.java:35)
>
>

SOA Server in Debug mode

How to start SOA server in Debug mode and what kind of errors or issues going to face.
What is the use to start SOA server in Debug mode.

Try this.
http://docs.oracle.com/cd/B31017_01/web.1013/b28950/sysprops.htm
Thanks,
Vijay

Start Oracle Application Server in Debug mode

We have oracle application server 10g with oc4j. How do we configure App server to start in debug mode so remote debugging from different machine can be done.
I am new Oracle Application Sever. OC4j is java container and it starts automatical when ORacleAServer starts.
Thanks,
MS

MadanShah, how did you start Oracle Application server? Let us say, you start it with opmnctl. In order to do java remote debugging with the oc4j process inside the OAS, you have to add the java remote debugging option to the "java-options" in the $ORACLE_HOME/opmn/config/opmn.xml.
<ias-component id="OC4J">
<process-type id="home" module-id="OC4J" status="enabled">
<module-data>
<category id="start-parameters">
<data id="java-options" value="-Xdebug -Xnoagent -Xrunjdwp:transport=dt_socket,server=y,suspend=n,address=5050 -Xrs -server -Djava.security.policy=$ORACLE_HOME/j2ee/home/config/java2.policy -Djava.awt.headless=true"/>
</category>
The "-Xdebug -Xnoagent -Xrunjdwp:transport=dt_socket,server=y,suspend=n,address=5050" is what I added. After starting OAS, you can connect to the oc4j process by selecting port 5050 using a java remote debugger that is included in any major IDE, like Jdeveloper. For more information, search for "remote debug" in the online help of Jdeveloper.

Error starting J2EE server in debug mode

I am trying to start the Sun 1.4 application server in a debug mode. I get an error
err:FATAL ERROR in native method: No transports initialized
: No such file or directory
Error [2] in bind() call!
Socket transport failed to init.
Transport dt_socket failed to initialize, rc = -1.
The setting in config.xml file is:-
debug-enabled="true" debug-options="-Xdebug -Xrunjdwp:transport=dt_socket,server=y,suspend=n,address=1044
Any help will be appreciated.
Thanks,
Milind

I changed the port number and it worked. Not sure why port 1044 as specified in the Sun documentation doesnot work.
Milind

After start-up from sleep mode, Mail 6.2 shuts down and needs to be rebooted

After starting my iMac (Mountian Lion OS) from sleep mode and then staring Mail, Mail will crash (shut down) and needs to be restarted. This does not happen every time but enough to be annoying. Does anyone else also experience this and is there a fix? I have sent problem reports to Apple but they just seem to go into a black hole with no response. I would appreciate any help or advice. Thanks in advance.

I am also seeing the symptoms of this on my large (3500+) network of macs. We have seen it happen on MacBooks and MacBook Pros. I am curious to know do you have multiple airports in your environment or a single airport?
Also have you found any way to mitigate these effects (i.e does it still happen if you go to the apple menu and choose the sleep command)
Just curious, I want to find a solution to this because it seems to be very similar to what our users are seeing.

Server looses Debug mode after a restart

Hello,
At the NWDS there is an option to enable the Server debug mode. When I do that the server restarts and debug mode is on. The problem is that if I restart the server again it looses the debug mode and than I have to enable it again from the NWDS (Which, again, requires a restart). The same symptom is happen if I do the enable through the Config tool at the Debug tab.
Any idea why this happen?
Roy

Hey Shubhadip,
I think you misunderstood my problem: I did save it, otherwise how the debig mode will be on. The problem is that after ANOTHER restart (after the restart to enable the debug mode) it loses the debug mode again.
Roy

How to start the server in debug mode

HI
Im working on weblogic server 8.1 sp. My requirement is to run the application in hosted on weblogic server with out restaring the server i.e dynamiically turn to debug mode with out stopping. IM using Log4j method for logging. please let me know how to do it... if any one have sample java code
Thanks & regards
shiva

I am not sure, how can you do it on the fly, but if you want to restart the server here are the parameters you need to add to the java arguments
-Xdebug -Xrunjdwp:transport=dt_socket,server=y,suspend=n,address=$Port
(where Port will be any port you want to connect to).
Thanks
Togotutor
<a class="jive-link-external" href="http://www.togotutor.com">http://www.togotutor.com</a> (Learn Programming and Administration for Free)
Edited by: togotutor on Aug 12, 2010 3:44 PM

Portal down after starting Server in debug mode

Similar Messages

Maybe you are looking for