Portal java servers shutdown and does not restart
HI there,
We are running Netweaver 7.0 SPS12 JSDK 1.4.2_13. We have 3 Central Instances (BI, CRM, ECC) on one server, and 3 Dialog Instances (BI, CRM, ECC) on another, with the SCS and ASCS clustered on a different server. AMD64 / Windows 2003 Server / MSCS cluster.
All 3 java stack instances go down at the same time on either server inconsistently with the following error in dev_jcontrol where the java jlaunch processes do not start up again....
[Thr 9856] *** WARNING => JsfOpenShm: ShmCreate (69, 312160, CREATE) failed(rc = 4 SHM segment already exists) [jsfxxshm.c 715]
[Thr 9856] *** ERROR => JsfOpenShm: Shm version mismatch (shm "JSF-ADM-CORRUPT", code "JSF-ADM-015") [jsfxxshm.c 761]
[Thr 9856] *** ERROR => Can't create shared memory segment 69 (rc = 8) [jcntrxx.c 1759]
[Thr 9856] *** ERROR => Can't initialize JControl Administration [jcntrxx.c 273]
[Thr 9856] JControlCloseProgram: started (exitcode = -1)
[Thr 9856] *** ERROR => JsfCloseShm: FiDetachIndex(SESSION) failed (rc = 6 invalid argument) [jsfxxshm.c 1243]
[Thr 9856] *** ERROR => JsfCloseShm: FiDetachIndex(ALIAS) failed (rc = 6 invalid argument) [jsfxxshm.c 1250]
[Thr 9856] *** ERROR => JsfCloseShm: FiDetachIndex(SERVICE) failed (rc = 6 invalid argument) [jsfxxshm.c 1257]
[Thr 9856] JControlCloseProgram: good bye... (exitcode = -1)
To start up the java instances again, the jcontrol process has to be killed and the cluster restarted from SMICM.
Any ideas? Please help!
kind regards,
Clinton
Hi,
CHeck help documentation for troubleshooting.
http://help.sap.com/saphelp_nw04s/helpdata/en/12/bb0a412a06f023e10000000a155106/frameset.htm
Regards,
Harini S
Similar Messages
-
10.9.1 installs, then system turns off and does not restart.
10.9.1 installs, then system turns off and does not restart. When I eventually turn it back on, it installs again, then turns off.. Endless Cycle.. I have booted to restore disk, found errors that needed to be repaired and tried to repair them but system told me, after a few minutes, its not possible to repair. When I restart back to main disk, it shows the install AGAIN and then turns off. Much appreciate any Ideas?
All I can tell you is that:
Antivirus software, aside from being next to useless on Macs, is a common source of problems with Mavericks.
Google Drive was incompatible with Mavericks last time I looked.
WD hard drives have software that comes on the drives that is incompatible with Mavericks, software that comes with the drives that they want you to install on your mac which is incompatible with Mavericks, and in some cases firmware in the hardware of the drive enclosure itself which is incompatible with Mavericks. And all of this software is completely unnecessary. The good folks at WD have really worked hard to ensure that their products won't work with Mavericks. Bless their little pointy corporate heads. I'll bet that's the last WD drive you'll buy.
Basically you would need to get all this stuff uninstalled from your hard drive before it will reliably work with Mavericks. But even then, it might not work, because old/bad/incompatible software can alter your OS and the kernel such that uninstalling it won't help- the OS/kernel may be damaged such that you have no alternatives other than to erase the HD and start over. And anyway, currently you can't boot your HD to be able to access the Finder so unless you're going to spend a weekend with the Terminal you won't be able to uninstall that stuff in the first place. If I were you I'd just go ahead and erase the HD and install Mavericks from scratch.
10.9.1 doesn't come on a CD. If you had another (working) mac you could make a bootable installer flash drive with DiskMaker X and an 8 GB key drive DiskMaker X (formerly Lion DiskMaker) , but then you'd still have the same problem, the incompatible software would still be on your HD, unless you erase it first before you try installing Mavericks again. So there's really nothing to gain by having the Mavericks installer on a disk.
If you have a third party utility like Techtool Pro 7 you might be able to boot from the TechTool disk and repair your HD enough for it to boot.
Message was edited by: arthur -
How to create a looping music player that does not restart when you go to other pages
Hello
I am new to web design. I apologize if I do not use the write
terminology. I am designing a website. I want to have a song that
loops continuously throughout the site and does not restart when
you click on the different pages. I have included a link to a site
that I found that does what I want to do. (Hopefully this link will
give you a better idea of what I am trying to describe)
http://www.marcuscoleministries.com/index2.html
Thanks for your time and considerationYou will have to use frames which in itself is a bad idea.
IMO music that
plays automatically is a terrible idea. It is likely to drive
away many
visitors and is unlikely to retain even a single visitor.
Avoid frames. Drop the music. You'll be happy you did.
Walt
"dbone1" <[email protected]> wrote in
message
news:fn36v6$de7$[email protected]..
> Hello
>
> I am new to web design. I apologize if I do not use the
write terminology.
> I
> am designing a website. I want to have a song that loops
continuously
> throughout the site and does not restart when you click
on the different
> pages.
> I have included a link to a site that I found that does
what I want to do.
> (Hopefully this link will give you a better idea of what
I am trying to
> describe)
http://www.marcuscoleministries.com/index2.html
>
> Thanks for your time and consideration
>
> -
my ipad mini does not restart when i press and hold the home and power buttons for a minute or more. what do i do? i really need to access some information on it. please help.
You need to connect to iTunes and restore.
iOS: Not responding or does not turn on
You may need to put the device into recovery mode, this is covered in the link on this page.
Did you back up the device? -
I just purchased a MacPro with 10.7.2 installed. I want to install 10.5 on a separate partition.
I created the partition with no issues, now when I put in the 10.5 install DVD and restart the computer, it does not restart.
All I get is a grey screen. no icons, no nothing. I have to shut the computer down.
I really need to do this. I plan on upgrading to FCP X, but I still need to finish some old projects that were done with FCP 7. I need the different boot drivesMac Pro - Mid 2010
Processor 2 x 2.66 GHz 6-Core Intel Xeon
Memory 8 GB 1333 MHz DDR3 ECC
Graphics ATI Radeon HD 5870 1024 MB
Software Mac OS X Lion 10.7.2 (11C74)
This is a brand new machine that I just purchased from Apple. It was delivered yesterday
The old computer is an old PowerMac G5, but my OS X install disc is a retail version of 10.5.
I also tried the OS X 10.5 install disc that came with my MacBook Pro (2.6 Ghz Intel Core 2 Dual).
Same issue - nothing but a grey screen when the system tries to boot from the DVD -
I have a mid-2011 iMac running Mavericks. When I click restart the computer goes to a white screen with a spinning circle and does not go any further until I hold down the power button to turn it off. What do I do?
Ok, sounds like the safe mode boot worked... You probably don't want to always be in safe mode though (some reduced functionality) so does it do a normal boot now? If not, you should then reboot into safe mode and run Disk Utility. Then select Macintosh HD on the left hand side, and click the Verify Disk button. If needed, it will ask you to Repair Disk. If there are errors found, Repair Disk again until there are none. Then try another normal boot and reply with result, wether good or bad.
-
When my Mac battery dies and I turn it back on, it always crashes on the grey screen with the progress bar, then it restarts (taking forever) and does not remember any of the programs I was running. MacBook Pro 13 inch running Mavericks
http://osxdaily.com/2014/10/17/os-x-yosemite-installation-stuck/
also use the Command-L to view logs during installation -
Xperia Z1 keeps shutting down does not restarts,and automatically stops and starts charging randomly
My Sony Xperia Z1 keeps shutting down due to high temperature even though its not overheated, or i am not running any app. It does not restarts even after i give it some time to cool down as it soon again displays the same messege (SHUTTING DOWN DUE TO HIGH TEMPERATURE), then when i connect a charger it automatically starts charging and discharging (even though if the charger is connected and ON) the cell phone
I request you to kindly look into the matter, expedite the situation and suggest me any possible solution asap
also i would request you to not to release any OS updates unless they are fully stable and functional, i have bought this device 6 months back and it has already malfunctioned 3 times which is a serious concern. I cannot keep on updating and repairing my cell phone after every month or so which i feel is very irritating.
Please stop treating these devices as developers guinea pigsI suggest that you try to repair the phone software using PC Companion..
Before repairing your device you may want to backup your information first. Check out this topic for more information on how to.
How to backup?
If the issue should still remain I think that this needs to be examined and fixed at a repair center. For more information about how to submit your phone for repair and where, contact your local support team.
- Official Sony Xperia Support Staff
If you're new to our forums make sure that you have read our Discussion guidelines.
If you want to get in touch with the local support team for your country please visit our contact page. -
Java applet works in windows and does not work in linux
Hello, guys!
I'm working with site which is located in vpn network at work.
I use browsers firefox 3 and opera.
When I want to open java applet using firefox or opera at first everything is fine then on the last stage of loading(judging by progress bar) applet hangs(progress bar hangs) and when I reload page firefox shows in the bottom bar: applet <applet's name> bail.
In windows everything works both in ie6 and firefox 3.
On both environments I have the jre 6 installed.
please help!Ok, I installed ies4linux and jre 1.5.16. I can work with that but when I start applet screen goes black and window frames dissapear.
To solve this problem(feature?) I disabled DirectX-based acceleration for Java 2D but that works for javacpl.exe and does not work for my applet. -
Problems to shut down, restart my Mac it displays a message saying Safari does not allow it. I try to quit Safari and does not do it.
Have you tried using Activity Monitor to shut down Safari?
Ciao.
Have you clicked on the Safari icon in the dock and seen if 'Force Quit' is displayed?
Message was edited by: OGELTHORPE -
I am running Itunes in Windows 7. Every time I exit, it restarts in a few seconds. If I restart my compter and forec close it, it does not restart, but If I use it at all the whole loop starts again.
Sorry, just to confirm, I DID NOT ACTUALLY ANSWER MY OWN QUESTION!
I replied to the previous message from my iphone and I managed to hit the link to "This has answered my question" by accident!
I AM STILL LOOKING FOR A RESOLUTION TO MY ORIGINAL PROBLEM. CAN SOMEONE ALSO NIW TELL ME HOW TO GET RID OF THE GREEN TEXT TGAT SAYS TGAT MY QUESTION IS ANSWERED? That is a pain! It should at least ask you to confirm that your question is actually answered and you didn't hit it by mistake, like I did! -
My iPad does not restart, I have kept the button for more than 10 seconds and will not turn off.
Please if anyone has any idea that I do, let me know.
thanksReset iPad
Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
Note: You have to hold 2 buttons down together. -
My Imac late 2012 running Yosemite does not recognise my Huawei 3g usb modem. itried to install Java bt still it does not although the same modem works with my MacBook pro . any help please
Hey there mbarikiwa,
If your iMac still has not recognized the usb modem, I would use the troubleshooting for Yosemite USB issues in the following article:
OS X Yosemite: If a USB device isn’t working
If the device is connected to a USB hub:
Make sure the device and the hub are the same speed. Connect USB 3.0 SuperSpeed devices to a USB 3.0 SuperSpeed HUB, USB 2.0 Hi-Speed devices to a USB 2.0 Hi-Speed hub, and so on.
If the device doesn’t have a power cord and is plugged into another USB device that doesn’t have a power cord:
Try plugging the device directly into your computer’s USB port or into a USB device that does have a power cord. You might need to disconnect and reconnect the other device as well, if it has stopped responding.
If you have many devices connected to your Mac:
Disconnect all USB devices except the device you’re testing, an Apple keyboard, and an Apple mouse. Make sure that the device is connected directly to the computer, and that any hubs or extension cables are disconnected. If you can use the device now, the problem may be with one of the other USB devices or hubs you had connected to your computer. Try reconnecting them, one by one, to your computer. When you find the device causing the problem, review its documentation for further troubleshooting steps.
Verify that the device appears in System Information:
Choose Apple menu > About This Mac. In the window that appears, click Overview, then click the System Report button to open System Information.
In the window that appears, see if the USB device is listed below Hardware in the Contents list. If the device appears but does not work, review the device’s documentation for further troubleshooting steps.
Restart apps:
Quit and restart any apps that use the device.
Restart your Mac:
Choose Apple menu > Restart.
Check your device’s USB connection
Thank you for using Apple Support Communities.
All the very best,
Sterling -
Is not abstract and does not override abstract method actionPerformed
I dont how to corr. Please help!! and thank you very much!!
import javax.swing.*;
import java.awt.*;
import java.awt.event.*;
public class test extends JFrame implements ActionListener, ItemListener
private CenterPanel centerPanel;
private QuestionPanel questionPanel;
private ButtonPanel buttonPanel;
private ResponsePanel responsePanel;
private JButton b1,b2,b3,b4,b5; //Create five references to Jbutton instances
private JTextField t1,t2,t3,t4,t5; //Create five references to JTextField instances
private JLabel label1; //Create one references to JLabel instances
private JRadioButton q1,q2,q3; //Create three references to JRadioButton instances
private ButtonGroup radioGroup; //Create one references to Button Group instances
private int que1[] = new int[5]; //Create int[4] Array
private int que2[] = new int[5];
private int que3[] = new int[5];
private String temp1, temp2, temp3, temp4, temp5, temp6, temp7, temp8, temp9, temp10,
temp11, temp12, temp13, temp14, temp15;
public test (String header)
super(header);
Container container = getContentPane();
label1 = new JLabel ("PLease click on your response to ");
q1 = new JRadioButton("I understand most of the content of this subject",true);
add(q1);
q2 = new JRadioButton("I see the relevance of the subject to my degree",false);
add(q2);
q3 = new JRadioButton("The workload in this subject is appropriate",false);
add(q3);
radioGroup = new ButtonGroup(); //JRadioButton belong to ButtonGroup
radioGroup.add(q1);
radioGroup.add(q2);
radioGroup.add(q3);
JPanel buttonPanel = new JPanel();
JPanel responsePanel = new JPanel();
JPanel questionPanel = new JPanel();
JPanel centerPanel = new JPanel();
b1 = new JButton ("Strongly DISAGREE"); //Instantiate JButton with text
b1.addActionListener (this); //Register JButtons to receive events
b2 = new JButton ("DISAGREE");
b2.addActionListener (this);
b3 = new JButton ("Neither AGREE or DISAGREE");
b3.addActionListener (this);
b4 = new JButton ("AGREE");
b4.addActionListener (this);
b5 = new JButton ("Strongly AGREE");
b5.addActionListener (this);
buttonPanel.setLayout(new GridLayout(5,1));
buttonPanel.add(b1);
buttonPanel.add(b2);
buttonPanel.add(b3);
buttonPanel.add(b4);
buttonPanel.add(b5);
t1 = new JTextField ("0",3); //JTextField contains empty string
t2 = new JTextField ("0",3);
t3 = new JTextField ("0",3);
t4 = new JTextField ("0",3);
t5 = new JTextField ("0",3);
t1.setEditable( false );
t2.setEditable( false );
t3.setEditable( false );
t4.setEditable( false );
t5.setEditable( false );
responsePanel.setLayout(new GridLayout(5,1));
responsePanel.add(t1);
responsePanel.add(t2);
responsePanel.add(t3);
responsePanel.add(t4);
responsePanel.add(t5);
questionPanel.setLayout(new GridLayout(4,1));
questionPanel.add(label1);
questionPanel.add(q1);
questionPanel.add(q2);
questionPanel.add(q3);
centerPanel.add(buttonPanel,BorderLayout.CENTER);
centerPanel.add(responsePanel,BorderLayout.EAST);
container.add(centerPanel,BorderLayout.WEST);
container.add(questionPanel,BorderLayout.NORTH);
q1.addActionListener(
new ActionListener(){
public void actionPerformed( ActionEvent e )
{ //actionPerformed of all registered listeners
if (e.getSource() == b1) {
que1[0] = Integer.parseInt(t1.getText()) + 1;
String temp1 = String.valueOf(que1[0]);
t1.setText(temp1);
else if (e.getSource() == b2) {
que1[1] = Integer.parseInt(t2.getText()) + 1;
String temp2 = String.valueOf(que1[1]);
t2.setText(temp2);
else if (e.getSource() == b3) {
que1[2] = Integer.parseInt(t3.getText()) + 1;
String temp3 = String.valueOf(que1[2]);
t3.setText(temp3);
else if (e.getSource() == b4) {
que1[3] = Integer.parseInt(t4.getText()) + 1;
String temp4 = String.valueOf(que1[3]);
t4.setText(temp4);
else if (e.getSource() == b5) {
que1[4] = Integer.parseInt(t5.getText()) + 1;
String temp5 = String.valueOf(que1[4]);
t5.setText(temp5);
} //end action performed
q2.addActionListener(
new ActionListener(){
public void actionPerformed( ActionEvent e )
{ //actionPerformed of all registered listeners
if (e.getSource() == b1) {
que2[0] = Integer.parseInt(t1.getText()) + 1;
String temp6 = String.valueOf(que2[0]);
t1.setText(temp1);
else if (e.getSource() == b2) {
que2[1] = Integer.parseInt(t2.getText()) + 1;
String temp7 = String.valueOf(que2[1]);
t2.setText(temp7);
else if (e.getSource() == b3) {
que2[2] = Integer.parseInt(t3.getText()) + 1;
String temp8 = String.valueOf(que2[2]);
t3.setText(temp8);
else if (e.getSource() == b4) {
que2[3] = Integer.parseInt(t4.getText()) + 1;
String temp9 = String.valueOf(que2[3]);
t4.setText(temp9);
else if (e.getSource() == b5) {
que2[4] = Integer.parseInt(t5.getText()) + 1;
String temp10 = String.valueOf(que2[4]);
t5.setText(temp10);
} //end action performed
q3.addActionListener(
new ActionListener(){
public void actionPerformed( ActionEvent e )
{ //actionPerformed of all registered listeners
if (e.getSource() == b1) {
que3[0] = Integer.parseInt(t1.getText()) + 1;
String temp11 = String.valueOf(que3[0]);
t1.setText(temp11);
else if (e.getSource() == b2) {
que3[1] = Integer.parseInt(t2.getText()) + 1;
String temp12 = String.valueOf(que3[1]);
t2.setText(temp12);
else if (e.getSource() == b3) {
que3[2] = Integer.parseInt(t3.getText()) + 1;
String temp13 = String.valueOf(que3[2]);
t3.setText(temp13);
else if (e.getSource() == b4) {
que3[3] = Integer.parseInt(t4.getText()) + 1;
String temp14 = String.valueOf(que3[3]);
t4.setText(temp14);
else if (e.getSource() == b5) {
que3[4] = Integer.parseInt(t5.getText()) + 1;
String temp15 = String.valueOf(que3[4]);
t5.setText(temp15);
} //end action performed
}//end constructor test
public void itemStateChanged(ItemEvent item) {
//int state = item.getStateChange();
//if (q1 == item.SELECTED)
public class ButtonPanel extends JPanel
public ButtonPanel()
public class CenterPanel extends JPanel
public CenterPanel()
public class QuestionPanel extends JPanel
public QuestionPanel()
public class ResponsePanel extends JPanel
public ResponsePanel()
public static void main(String [] args)
test surveyFrame = new test("Student Survey") ;
surveyFrame.setSize( 500,300 );
surveyFrame.setVisible(true);
surveyFrame.setDefaultCloseOperation (JFrame.EXIT_ON_CLOSE);
}//end main
}//end class testis not abstract and does not override abstract method actionPerformed
Oh, I see that the title of your post is an error message? Ok. Well, the test class is declared as implementing an ActionListener. That means the test class must have an actionPerformed() method. Your test class apparently does not.
It does not appear that the test class needs to implement ActionListener. You are using annonymous classes as listeners. -
Is not abstract and does not override abstract method ERROR
Hello. I'm new at all this, and am attempting to recreate a sample code out of my book (Teach Yourself XML in 24 Hours), and I keep getting an error. I appriciate any help.
This is the Error that I get:
DocumentPrinter is not abstract and does not override abstract method skippedEntity(java.lang.String) in org.xml.sax.ContentHandler
public class DocumentPrinter implements ContentHandler, ErrorHandler
^This is the sourcecode:
import org.xml.sax.Attributes;
import org.xml.sax.ContentHandler;
import org.xml.sax.ErrorHandler;
import org.xml.sax.Locator;
import org.xml.sax.SAXParseException;
import org.xml.sax.XMLReader;
public class DocumentPrinter implements ContentHandler, ErrorHandler
// A Constant containing the name of the SAX parser to use.
private static final String PARSER_NAME = "org.apache.xerces.parsers.SAXParser";
public static void main(String[] args)
// Check to see whether the user supplied any command line arguments. If not, print an error and exit.
if (args.length == 0)
System.out.println("No XML document path specified.");
System.exit(1);
// Create a new instance of the DocumentPrinter class.
DocumentPrinter dp = new DocumentPrinter();
try
// Create a new instance of the XML Parser.
XMLReader parser = (XMLReader)Class.forName(PARSER_NAME).newInstance();
// Set the parser's content handler
// parser.setContentHandler(dp);
// Set the parsers error handler
parser.setErrorHandler(dp);
// Parse the file named in the argument
parser.parse(args[0]);
catch (Exception ex)
System.out.println(ex.getMessage());
ex.printStackTrace();
public void characters(char[] ch, int start, int length)
String chars ="";
for (int i = start; i < start + length; i++)
chars = chars + ch;
System.out.println("Recieved characters: " + chars);
public void startDocument()
System.out.println("Start Document.");
public void endDocument()
System.out.println("End of Document.");
public void startElement(String namespaceURI, String localName, String qName, Attributes atts)
System.out.println("Start element: " + localName);
for (int i = 0; i < atts.getLength(); i++)
System.out.println(" Attribute: " + atts.getLocalName(i));
System.out.println(" Value: " + atts.getValue(i));
public void endElement(String namespaceURI, String localName, String qName)
System.out.println("End of element: " + localName);
public void startPrefixMapping(String prefix, String uri)
System.out.println("Prefix mapping: " + prefix);
System.out.println("URI: " + uri);
public void endPrefixMapping(String prefix)
System.out.println("End of prefix mapping: " + prefix);
public void ignorableWhitespace(char[] ch, int start, int length)
System.out.println("Recieved whitespace.");
public void processingInstruction(String target, String data)
System.out.println("Recieved processing instruction:");
System.out.println("Target: " + target);
System.out.println("Data: " + data);
public void setDocumentLocation(Locator locator)
// Nada
public void error(SAXParseException exception)
System.out.println("Parsing error on line " + exception.getLineNumber());
public void fatalError(SAXParseException exception)
System.out.println("Fatal parsing error on line " + exception.getLineNumber());
public void warning(SAXParseException exception)
System.out.println("Warning on line " + exception.getLineNumber());Check to make sure that the arguments are consistent with your ContentHandler class. Probably the wrong type.
I think you forgot to include the skippedEntity method, it seems to be missing. Even if an implemented class has a method that you are not using, you still have to include the method in your code even if it doesn't do anything.
Message was edited by:
ChargersTule1
Maybe you are looking for
-
Voice memos app not saving properly
I am using an iphone5 running iOS7.1.1 and performing the following actions will cause Voice Memos app not saving recordings. I have sent a feedback to Apple but is wondering if anyone else is found having similar problems. 1) Run Voice memos app and
-
Why am I being charged for THEIR mistake?
I signed up online to have new internet service started along with phone service. I was told it would be on May 6th. A guy even came to my home and told me it would be turned on that night. After 2 days with still no internet, I called and complai
-
So, I keep getting these emails from Comcast's Constant Guard service claiming "Constant Guard from XFINITY identified that one or more of your computers may be infected with a bot." They seem to be dead serious about it, though Comcast never provid
-
Checking to see if I have all my movies download and backed and realized I noticed a duplicate of a purchased movie. Thor: The Dark World plus the iTunes extras. I switched view all duplicates and also include purchased iTunes movies. How do I delete
-
Can anyone please explain what is a certification process of payment file. Is it an enhance ment in SAP, if yes how is it done. Thank you