Portege 3010ct: Question about USB drivers under W2k

Can somebody point me in the direction of the Windows 2000 drivers for the Portege 3010CT USB port? I can only find Win 95 and 98 and these don't seem to work.
Many thanks,
Adam

Hi
Usually its not necessary to install any extra USB drivers for W2k or WinXP.
I have read on some websites that sometimes the service packs update will solve the driver problems. You should check if you have installed all SP for W2k.
I have also found this site:
http://www.usb-drivers.com/companies/667.htm
You should check it.

Similar Messages

  • About to purchase but question about usb access to Sony DVD-RW camera

    I am on the verge of purchase of a macbook and it would be my first mac at that. Specifically, I am looking for information on using the usb connection between my camera and the macbook. I am coming from the Windows world, and the camera software is windows only. I record my stuff in VR mode, and when I plug in via usb the windows software allows me to pull off the VRO files. Then I have another windows program that is able to read the VRO files and I can move them around (I don't edit the contents of the VROs), put transitions and then create a dvd. My question when moving to the macbook, can I still record in VR mode and then when done recording, without finalizing the disk, hook the usb cable to the macbook and it will be able to read those files? I read in other posts something similar but not definitive that it could not do this. There might be other software (ie, something call readDVD) that might be able to but could not determine, for sure, that it could do this over the usb (since I can't pull the 8CM disk and put it in the non-tray DVD drive). Or is there a better suggestion, please be kind that I don't know what is possible on the MAC.
    For what is it worth, my scenario that I have put up with (because it gave me results that were adequate) on the windows side, had me record in VR mode and it gave me control over all the individual segments (hitting record and then stop is a segment) that I could manipulate individually with the windows software. I don't know enough about what is possible with the usb connection and the software on the MAC to know what to expect out of the box and if I have to buy additional software (to pull the movies off the video camera). If I recorded in Video mode, and then finalized and then hooked the usb cable to the macbook, would the resultant files be able to be read by iMovie? If so, would it be the individual segments or would it be one be movie (ie, all segments rolled up into a/many vob(s))? I want to be able to join many segments from many different disks onto one dvd. Maybe that is the crux of my question and may really be better suited for the iMovie forum rather than this one. If, so, please forgive my ignorance.

    Welcome to macbook forum,
    Could you post your camera model / type, so we can check that out for you in order to give you better answers.
    Or you can check this link for camcorder that supported on new iMovie 7.x.x.
    http://docs.info.apple.com/article.html?artnum=306171
    Good Luck.

  • Question about usb in labview

    I am currently doing a project about designing standalone data acquisition module with USB 2.0 interface.
    For the hardware, a USB FIFO chip(FT245BM) is used to communicate with PC via USB with the driver DLL provided by the manufacturer (FTDI).
    I want to use labview (version 7.0)to develop a data logging software and I learned that the functions in the DLL could be called by the 'library call function node' in labview.
    My question is:
    1.Apart from labview, do I need to intall Measurement and Automation Exploere to configure the hardware before I use it in the labview?
    2. I noticed that the type of call in labview should be configured as either 'c' or 'stdcall'. My knowledge about C/C++ is poor, could someone explain them in
    detail and which one shall I choose?
    3.I heard that not all the DLLs could be used in labview (due to the problem of different format???). I don't quite understand about this. Could anyone be kind to explain about this as well?
    Many thanks!!!

    Xiaohui wrote:
    > I am currently doing a project about designing standalone data
    > acquisition module with USB 2.0 interface.
    >
    > For the hardware, a USB FIFO chip(FT245BM) is used to communicate with
    > PC via USB with the driver DLL provided by the manufacturer (FTDI).
    >
    > I want to use labview (version 7.0)to develop a data logging software
    > and I learned that the functions in the DLL could be called by the
    > 'library call function node' in labview.
    I assume your chip comes with a Software Development Kit (SDK) with a
    ready made driver. This driver consists of a kernel mode driver and the
    user mode shared library (DLL). LabVIEWs call library node can be used
    to call such user mode DLLs.
    > My question is:
    > 1.Apart from labview, do I need to intall Measurement and Automation
    > Exploere to configure the hardware before I use it in the labview?
    Very unlikely, as the driver which comes with your SDK for the chip will
    be not configurable at all in Measurement & Automation Explorer (MAX).
    MAX really is only to configure National Instruments hardware devices
    and to some lesser extend external measurement devices connected through
    the GPIB, VXI and PXI bus.
    The NI-VISA driver 3.0 which comes in LabVIEW 7.0 can also directly
    communicate with the raw USB interface of some devices. If you want to
    use that interface you would NOT install the driver for that device and
    would configure that device in MAX instead. You do need to know the
    manufacturer ID and Device ID of your USB chip for that. Also the
    programming in LabVIEW through the VISA functions is possible but it is
    not very simple and completely dependant on the implemenation of the USB
    communication by that chip. There are some documents on Developer
    Exchange and also some discussion topics here on this forum about VISA
    and USB communication.
    > 2. I noticed that the type of call in labview should be configured as
    > either 'c' or 'stdcall'. My knowledge about C/C++ is poor, could
    > someone explain them in detail and which one shall I choose?
    Most Windows DLLs use stdcall but this is not a must. If you get it
    wrong you will simply crash LabVIEW. The documentation or if that
    doesn't work the header file which comes with the DLL should give you
    this information, although for the header file you need to know a little
    C to understand where it shows this.
    > 3.I heard that not all the DLLs could be used in labview (due to the
    > problem of different format???). I don't quite understand about this.
    > Could anyone be kind to explain about this as well?
    Windows DLLs should be fairly standard. The only problem could be .Net
    assemblies which are not really DLLs but a complete archive of DLL's
    documentations, certificates and, and, and!
    It's still very unlikely that a device would come with a .Net assembly
    instead of a simple DLL with the according API.
    Rolf Kalbermatter
    Rolf Kalbermatter
    CIT Engineering Netherlands
    a division of Test & Measurement Solutions

  • Question about installing drivers on Vi

    Hey,?Within the next couple of weeks, I intend to purchase a?X-Fi Fatalty FPS card. I know the Vista drivers aren't up to scratch at the moment, but I'm in no rush to upgrade to Vista, although I have access to the RTM through TechNet. As soon as all drivers are of a good standard then I'll upgrade - until then I'd stick with XP which works great. My question is this, If I buy this card it'll ship with a driver CD. I'll need to install the drivers/creative applications from this CD and then update them from the website. The drivers on the disc will be for Windows XP, and not compatible with Vista. When I format the dri've and install Vista, how do I go about installing the Creative Vista drivers. The downloadable ones from the website require the main CD drivers to be installed, which I won't be able to install as they're for XP. Hope that makes sense. Thanks.

    Ooh, perhaps I got the wrong end of the stick then. Im basing this on my experience with an old Creative Audigy card I had years ago, but If memory serves me correctly it was actually an OEM card. So what you're saying is, when I receive my X-Fi, I can not use the CD and straight away download the latest drivers/apps from the creative website and install them without needing to run the CD through first?Thanks for your reply.

  • *Solved* Question about ATI Drivers

    Ok, I'm just finished installing, and I know most distro's, ask you to remove the open source drivers, before adding in FGLRX  drivers.  Looking at the wiki, I didn't noticed if this needed to be done, and after going through the install, I rebooted.  It went as planned until kdm went to load.  The screen was unreadable.  I used the cd media to mount root, and removed catalyst, and re-installed the opensource drivers.  All is well atm, so I'm trying to figure out what I missed.  My question atm though is during the FGLRX install, it ask's if you want to removed the opensource drivers due to conflict.  If I hit yes, will pacman it automatically remove the required drivers, or do I need to manually remove the Fx86 drivers on my own?
    I do apologize for not having a /etc/X11/xorg.conf report, as it slipped my mind while fixing everything. I'll try to make a better habbit of getting it made. I did do a aticonig --inital before the reboot, so i know it won't that.
    If I missed anything on the wiki, please let me know, I'll look again at it after dinner.
    Thank you all for  your time in the matter.
    Last edited by bigcountryva (2012-09-30 01:01:49)

    Silex89 wrote:
    Hi there
    First off, which installation method are you following? (ABS using the AUR package, the unofficial repository or the AMD installer). Depending on which method you use, you'll have (or not) a resolved dependency. For instance, you have to remove both the open source driver and your former xorg.conf file (safer is to back it up) to be able to install Catalyst with the AMD's site installer.
    If you use AUR (with a tool like Yaourt for example) or the repo method, pacman/yaourt should do it for you, but in a lot of cases it doesn't (I switched to Catalyst having my OpenBox session built already, so when I tried to remove the open source driver it complained about all of the apps that I had installed for removing a dependency like libgl or mesa) and you'll have to do a pacman -Rdd xf86-video-ati to make it work
    I'm wondering if you remembered to add the mkinitcpio hook (which is needed to make Catalyst work).
    What I would suggest is to re-read the wiki page for Catalyst, see if your card is still supported by Catalyst, maybe your card needs Catalyst-Legacy...
    Best of Luck with that
    I figured it out, and got it working.  I had a typo adding the module for flgxr driver.  Fixed it and a soft boot later, all is well.  I also deicided to make it so I have to "startx" into my gui, incase this happens again, I won't need the installation media.  Thanks for the input.

  • Questions about USB sound blas

    I just got the Creative USB Sound Blaster Audigy 2 NX, and I simply love it. It was well worth the $0 I paid for it with a gift card I had to blow anyway. I have come to expect quality from Creative, through 2 sets of speakers, an MP3 player, and now a USB sound device.
    I do have a question though. I've got USB . in the machine I use the device in. I'm wondering if it would make any difference to use USB 2.0?
    Also, there was a very large cable that came in the box that I couldn't find out what it was. Do I need this cable? My music is working great right now, but I'm wondering if I need that cable.

    The USB-6008 is supported by both DAQmx and DAQmx Base, so you can
    definately use a USB-6008 with Visual Basic 6 through the DAQmx
    API.  Information on how to get started can be found at this link:
    http://digital.ni.com/public.nsf/websearch/B22FE2B0F9C8935286256E920073DA07?OpenDocument
    While the DAQmx driver is the preferred API under Windows, you may also
    use the DAQmx Base driver with VB 6 if you prefer.  It is slightly
    more work to set up however.  Instructions on how to do that can
    be found at the following link:
    http://digital.ni.com/public.nsf/websearch/A21A013CA229A5988625703E0025A8AE?OpenDocument

  • Webcam 2 usb drivers for w2k

    Hello I need drivers for Windows 2000 of my camera Webcam II (PN:0000424) i dont found the drivers in your donwload area is any work around to make it works on W2k? Any solution?

    Quote from: acacia987 on 03-August-05, 23:04:27
    did you have to modify your connecter when you hooked up your front usb ports?
    Maybe , i don't remember .. (btw: there is two versions of the slk3000b , an early model and a more resent one)
    Check it visually ,how hard is that .
    jusb1/jusb2
    [2][4][6][8][10]
    [1][3][5][7][9]
    No wires on 9 or 10
    Is there a Pin 10 in JUSB1 and/or JUSB2 connected or not ? YES or NO
    Does bios post PCI list show ECHI initilalized with IRQ ?  YES or NO
    Does BIOS show enabled or "USB 1.1+USB 2.0" enabled ? ENABLED or V1.1+V2.0
    Does windows device manager show Enhanced host controller ? YES or NO
    (U should have three - The Enanced supports one hub for 8 devices - Each OHCI suppoert one hub with 4 ports each)
    Have you done the microsoft trick to reinstall drivers for each USB device inkl the hubs through device manager ? YES or NO
    This is what I like you to answer ...

  • Question about USB power adapter

    hey guys, i have a question, i have an USB power adapter as a charger for my itouch and I accidentally dropped the USB power adapter on the floor. would it get damage? and if it's damage, would it be advisable to charge my itouch using it? would it damage my itouch?

    Hi,
    Bizzarre question!
    How far did it fall?
    Do you have carpet?
    Is it Cracked?
    *No one here can give advice on that without fear of being sued*
    Good luck,
    Dud.

  • Question about DB13 jobs under MSCS environment

    Hi,
    I have migrated my system to cluster hardware.It´s two nodes windows 2003 server R2 x64, with MSCS and Oracle 10g.
    I need run DB13 operations, so I have installed the standalone gateway following note 657999. Gateway is running anda RFC works fine.
    Now SAP group is running in node A and Oracle group is running in node B, and when I try to run a database check through DB13 job returns this log:
    Job started
    Step 001 started (program RSDBAJOB, variant &0000000000210, user ID CONSULTORAC)
    No application server found on database host - rsh/Gateway will be used
    Ejecución del comando lógico BRCONNECT En máquina ACDCPDPSR3002
    Parámetros: -u / -jid CHECK20101201092709 -c -f check
    BR0801I BRCONNECT 7.00 (16)
    BR0252E Function fopen() failed for 'J:oracleACPsapcheckceernjjz.chk' at location main-9
    BR0253E errno 13: Permission denied
    BR0121E Processing of log file J:oracleACPsapcheckceernjjz.chk failed
    BR0280I BRCONNECT time stamp: 2010-12-01 09.27.11
    BR0301E SQL error -12560 at location db_connect-2, SQL statement:
    'CONNECT /'
    ORA-12560: TNS:protocol adapter error
    BR0310E Connect to database instance ACP failed
    BR0806I End of BRCONNECT processing: ceernjjz.chk2010-12-01 09.27.11
    BR0280I BRCONNECT time stamp: 2010-12-01 09.27.11
    BR0804I BRCONNECT terminated with errors
    External program terminated with exit code 3
    BRCONNECT returned error status E
    Job finished
    Error 1: BR0252E Function fopen() failed for 'J:oracleACPsapcheckceernjjz.chk' at location main-9
    Brconnect is trying to write .chk file in SAPDATA_HOME directory and it can´t. When I execute the command at OS level in node A (where SAP group is running) I get same error, but when I execute same command in node B it run without problems.
    Error 2: 'CONNECT /' ORA-12560: TNS:protocol adapter error
    No listener.
    SAP try to run commands on the node where SAP group is running, and it can´t works with Oracle group resources like listener or sapdata_home disk.
    My question, is it possible execute DB13 actions whene each group is running in different nodes?
    If is possible, how can I solve my problem?
    Thanks in advance.
    Pablo.

    Hello,
    As stated in point 7 within Note 446172 :
    7.  In Windows, make sure that the USER environment variable for
        SAPSERVICE<sid> contains <sid>ADM. This variable controls the user
        under which the external command is started. See also Note 556232.
    regards,
    John Feely

  • Question about USB mice using

    Can anyone please let me know whether any precautions need to be taken when using a mice ; generally is there any need to exert caution while connecting and removing the mice from USB port.
    As of now, the mice is being detected automatically and there is no icon for "safely remove hardware" .
    Thankyou very much
    Best Regards

    Hi Karthik,
    When an external device is connected to your notebook it it will usually transmit and receive data in real time. Consider your USB Mouse, you click one of the buttons and this is transmitted to your notebook where it is acted upon by the operating system. In effect this occurs in real time and there is no buffering of data to worry about so the device could be unplugged at any time without the need to 'Safely Remove Hardware'.
    Now consider a USB attached hard drive. In this case if data is being written to the hard drive (or read from it) then this does not occur in real time since the data is 'buffered' in transit in order to optimise the hard drive utilisation. A similar system is used when ripping/burning CDs and DVDs. In this case the 'Safely Remove Hardware' option is used to ensure that the last bits of data are cleared from the 'buffer' before the device is disconnected. If this were not done then some data loss would be experienced when the device was disconnected.
    Since your mouse is not transferring data it is therefore not using any buffering.
    regards,

  • Question about USB mobile modem

    I have Toshiba Equium with Vista Home Premium. I connect to the internet using a huawie mobile modem. It comes pre installed with it drivers you just plug in and it installs its own software.
    I have noticed it will only work on the USB port where I originally installed from and not the other. I have uninstalled the software and tried installing from the other port and this works so its not the USB ports.
    Any ideas?

    this is because each of the usb ports have thier own drive letter e.g. on my pc they vary from e,f,g,h,i,j depending on how many are connected and if there is a hub or whatever
    when the software was installed the directions to reach the usb modem were go to drive e.g. [J]
    when you plug it into another port the eltter changes as it is in a different place so when your software tries to find it, it will look in the specified place and it will see nothing is plugged therefore will think that no modem is connected at all.
    understand?
    hope it helps
    Bas

  • Questions about USB-6008

    I need a simple (low cost) USB DAQ
    so I was thinking to get the model
    NI-6008.
    Can I use VB6 to program it?
    NI provides (on the bundled CD), dll,
    library, samples on how to
    program it (with VB6)?
    Thanks in advance,
    Frank

    The USB-6008 is supported by both DAQmx and DAQmx Base, so you can
    definately use a USB-6008 with Visual Basic 6 through the DAQmx
    API.  Information on how to get started can be found at this link:
    http://digital.ni.com/public.nsf/websearch/B22FE2B0F9C8935286256E920073DA07?OpenDocument
    While the DAQmx driver is the preferred API under Windows, you may also
    use the DAQmx Base driver with VB 6 if you prefer.  It is slightly
    more work to set up however.  Instructions on how to do that can
    be found at the following link:
    http://digital.ni.com/public.nsf/websearch/A21A013CA229A5988625703E0025A8AE?OpenDocument

  • Questions about JDBC-Drivers

    Hi,
    I'm working with JDBC-Drivers for the first time.
    How can I get detailed information about the database, subprotocol etc. the driver supports. In ODBC there exist some information functions like SQLGetInfo to explore drivers. But there seems to be no way to do this with JDBC.
    Can anybody give me some advice how to get this information ?
    J�rgen

    Hi,
    after instantiating an object implementing the Driver interface I want to know what database this driver works for. If possible, this should be done without connecting to the database. I supposed a driver should store such information in itself but there seems no way to get this information.
    The Driver interface declares a method 'getPropertyInfo' to extract information about the possible properties for this driver. Unfortunately I didn't found any description what lookup strings can be used.
    Do you know how to go on ?
    Thanks and regards
    Jugi

  • Portege P7220: Question about SymEvent

    I have a Portege P7220, bought 2001, with Win2000. I tried to upgrade to XP, using the PCMCIA CD-drive that I bought from Toshiba with the computer.
    1. During early stages of installation, it told me that I didn't have a CD drive installed, with some info about "SCSI" which i didn't understand, and it aborted the XP installation.
    2. So I restarted Win2000, and got a dialog box with title "NAV Autoprotect" and message "Unable to start SymEvent". If I dismiss the dialog box, the system apparently works.
    Should I be worried about the warning dialog box? Any way round the problem I met when trying to install XP? Would appreciate advice.
    David

    Well, I found that "SymEvent" belongs to an old installation of Norton Antivirus, which I've got rid of. But I havent found a solution to the problem of XP Setup not recognising the external CD drive.

  • Satellite C50-A-571 -Two questions about Toshiba drivers download

    Hello all , great day .. how is it doin?
    I'm new to this forum , it's good to be here hoping will find solution to every problem we facing
    My first question is : why the drivers download from "http://www.toshibamea.com/" is so slow and limited or something? , it never finish downloading , I'm always having connection interrupted when trying to download a driver, isnt there other mirrors or something?
    Second question:
    why is there so many unnecessary drivers ? like I set all my preferences, product type, family,model , series ... and it gave me 33 driver , and some of them aren't drivers for my laptop
    I have a Satellite C50-A-571 notebook

    Hi and welcome
    Im not some expert but Ill try to offer my answers.
    1/
    As far as I know support page you use is offered for Middle East and Arica. I don't know where is the server placed but download should not be problematic. In the past I used it few times for drivers check and everything was OK. Maybe is there some problem with your Internet connectivity.
    Toshiba support and download page is definitely not limited and can be used anytime you want.
    2/
    Ive checked download page and found 33 results for Win7 64bit so I presume you want to install this Windows version.
    Anyway all listed stuff are not just the drivers but also useful Toshiba specific tools and utilities. This tools and utilities control some special useful special features like special keys functionality or HDD protection.
    I can just recommend you to install all of them and have full control over your machine. Of course if you don't like or don't need some of them they can be disabled or removed from the system.
    I hope my opinion is useful for you. If you have more questions you are welcome.

Maybe you are looking for