Posible p4n diamond heat problem and other beep question

Hi was using my p4n diamond for about 2h 30min and it all of a sudden just cuts out with no warning.
im unsure if its heat related thought the constant 55C is not as good temp as i should probably have but it stays stable there.
Also when i recently installed msi core it said i was very close to the voltages it had in the display just to hope to rule out power problems.
i have the cases 120mm exaust fan in the back an 80mm input fan in thefront and then the cpu fan that came with my pentium d 830 .
if its heat related should i get another 80mm fan as an exaust or an 80 mm input fan. i have one more spot on the door of the case.
----other beep question--
I was also wondering about the beeps on my computer. when i first was working with this pcc i had no beeps but then when working i had one beep before os then two after os and usb case plugs and floppy , 3 when i put on a printer and then back to one and then no beeps.
are these my beeps going down related to my heat or is this mother board short lived . one beeps soposed to mean that its loading properly
thanks

regarding your question about target temperature. my board isn't exactly the same as yours, but it's close.
you are right that you can lower the target temp and it will tend to cool the cpu because the fan runs faster at a lower temperature. the way i set up mine was to DISABLE the target temp and that gives the fan full voltage at all temps. that way, the fan rpm will bottom out at 2250rpm (instead of 1100rpm up to the target temp) or so even at lower temps.
also keep in mind that your cpu temp in the bios disply should be a few degrees HIGHER than the temp in "idle windows".
the intel data sheet for the pentium D 8xx series says that the max temp is 69C. so your cpu shouldnt have a problem at 55C.
i ran a prime95 primality test for about 17 hours at 60C to test stability (while using the computer for my normal foreground tasks) and didn't have a problem. i'm NOT recommending this. but i wanted you to know that this cpu doesn't have a problem with temps in the 60C range. and that msi motherboard will stand up to rough treatment.
also, in my humble opinion, i would NEVER run those msi windows utilities. they may be causing you a problem with stability. i use speedfan from almico to monitor temps and i have it set up to generate sound and visual warnings at certain temps. the F1 docs are good. if it were my system, i would go so far as to reinstall windows and format the C: to get rid of core center. i wouldn't even trust the uninstall unless you're good enough to surgically remove it manually.
also make sure you turn off EIST in the bios. it wont impact your temps significantly. that nvidia nforce sli intel edition has a problem with 14x multiplier and pentiumD. and EIST bumps you down to 14x occaisionally.

Similar Messages

Heating problem and battery backup

Recently I bought a macbook pro (7 days). I am facing heating problem and its battery backup is also not good, 3-4 hrs, but company claims 7 hrs. What should I do?

For more on laptop temperature, look here:
http://support.apple.com/kb/HT1778
Take note of this part:
While there are third-party utilities that measure the temperature of a notebook computer, it is important to understand that these utilities are not measuring the external case temperature. The actual case temperature is much lower. Never use third-party applications to diagnose possible hardware issues—instead,contact Apple or go to an Apple Retail Store or Apple Authorized Service Provider.

P4N Diamond startup problems

I've had problems with my P4N Diamond-based PC since I built it a couple of months ago. Through excellent help from this forum I eventually resolved the main problem - I was using Maxtor 300GB drives which (due to their staggered spin-up) were incompatible with the Nvidia drive controller.
OUTSTANDING PROBLEMS:
1) Since before then though most boot-ups were taking longer than they should and I traced the problem via the event viewer, which reports disk errors and suggests replacing the drive. I have tested 5 drives in total (3 different models) and I always get the same error. I am 99% confident that the reported disk errors are actually motherboard related and I am suspecting that I either need to change the BIOS or the mobo.
But, changing the mobo is my very last resort and I can't see that changing the BIOS from 1.30 to 1.40 will improve anything (and may introduce new issues?) as there appear to only be updates to the Silicon disk controller.
2) Am getting 4 beeps (in total) on startup - (1-2-1) beeps once, pauses, then beeps twice, pauses, then 1 low tone beep. I have checked the BIOS beep codes page, but am confused about what my beeps mean?
3) PC wouldn't shut down last night, so I had to do hard shut-down. This morning it took 20 minutes to start up! This problem appears to be linked to problem 1.
4) My PSU blew (a couple of weeks ago) and I recently got a replacement. Enermax assured me that it wouldn't have harmed the other PC components. The problems above were occuring before the old PSU died, but I am unsure whether this could be linked to any of the above issues.
All previous burn-in tests, memtests and hard disk checks have all come back clear. I think that the starting point is for me to understand what the beeps mean and to see if resolving the beep problems stops the other issues.

nwheeler,
Well i spent 2 and half hours stright looking for BIOS beep codes for our motherbaord. But the only thing that i found was the same information that is on here. The P4N has different toned beeps, i know that my hearing is not messsed up. I think that i made a pretty exsustive search for it so im still stumped. I even tried the Diamond Forums (there are not that many posts there). You can check that out here: http://diamondclub.msi.com.tw/eng/
There is one silver lining though. I came across a post on another forum board saying that you might get one beep for every USB device you have pluged into your machine. So do a count and see if that has something to do with your mixed code.
In my case i hear the one beep before the BIOS flash screen, from my search that first beep says that everything is fine. But after that i get a high beep followed up a few seconds later by a lower toned beep. As for USB devices i have 2 pluged into my machine...the first being a USB mouse, and the second being a Joystic. Later when i get home today im going to try unpluging them to see if i get a different beep process. Ill let you know what i find out.
GL

[875P Neo Series] P4N Diamond - RAID problem

Hi,
I just purchased a P4N Diamond. I've installed WinXP-SP2 on a single Samsung 70GB IDE disk on IDE1 as Primary Master. Two CD/DVD drives are on IDE2.
SATA-1 and SATA-2 are connected to Hitachi 500GB SATA drives.
I've entered the nVidea RAID utility in Bios by pressing F10 during boot, and established the two SATA drives as a mirrored volume.
After reboot the RAID volume is detected and appear as sync'ed during reboot.
Now comws the problems: I am utterly unable to set these two drives up as a mirrored volume under WindowsXP-SP2:
When I enter Control Panel -> Administrative Tools -> Computer Management -> Storage -> Disk management, both disks appear as separate disks and Unallocated. When I Right Click to create a new volume, I don't the option of creating a Mirrored volume.
Even stranger thing happens if I now exit everything and reboot: The nVidea RAID utility in BIOS has now been reset to two separate drives.
Question is: What do I do wrong, and how do I get these two 500GB drives set up as one mirrored RAID volume?
Regards,
Robert H

read the raid manual ?
https://forum-en.msi.com/index.php?topic=84043.0

[nVidia Series] P4N Diamond raid problem

i have a P4N diamond motherboard with a 3 ghz cpu on. I have setted up a raid 5 with 4 drives on the nvidia raid controller. on the sillicon raid controller i want to have to have 2 sata disks striped. In the sillicon bios for the raid i have configured those 2 drives for raid0 and i get 1 logical drive which i also can see from the bios. My problem is then that when i boot up the computer and begin the installation of windows xp ( and give it the sillicon driver with the F6 button ) then i get 2 logical disks on the sillicon controller instead of my striped raid0 drive.
What do i do wrong? everything looks right for me in the bios. Raid is enabled and the serial ata ports are enabled. Help please
- Jesper H

problem fixed by using the right silicon driver. the orginal diskette driver can not be used. you need to make a diskette with the raid version of the silicon driver.

P4N Diamond - Some quirks and annoyances. :)

Alright, I'd just like to check if anyone by chance happens to have these issues too.
1. Sound Blaster Live! optical output doesn't register as Dolby Digital on my Yamaha HT-5730 receiver. I have the Creative utilities installed and no matter what option I choose, either 2 speaker, 5.1, or forcing Dolby Digital only, it always shows up as PCM and can only use Pro Logic II (boo). I know my receiver supports Dolby, I had an Intel D915PBL and Abit IC7 motherboard previously and both had Dolby Digital ability on the onboard TOSlink. I mean if the P4N SBLive didn't advertise that it supports Dolby Digital, then I wouldn't have so much of a problem, but the fact is that it does and it's not working.
2. I use an MSI Vox TV tuner. When I power my system up while it's plugged into USB, the machine will hang at the HDD summary screen until I unplug it and reboot. With it unplugged, it will still hang, but only once out of every 10 power-ups. The tuner works fine after I plug it in after it loads OS. Currently there are 6 devices plugged into USB; keyboard, wireless mouse, monitor USB hub, MSI Vox, and Logitech Quickcam. Machine will hang whether the Vox is plugged into the monitor hub or in the back of the machine.
3. Machine powers on 1-3 minutes after shutdown. I have a feeling the network connection is tickling the machine, but I do not have the WOL set in BIOS...it just powers back on by itself. When I had the system using WiFi, it would not do this. Only once I started using the Marvell onboard NIC it would power on. The problem doesn't repeat if I shut the system down a second time.
4. Oh yeah, before I forget... the USB keyboard won't work in BIOS level about 4 out of every 5 times I power the machine on, so I have to use a PS/2 KB to go into the BIOS most of the time as well as modify settings or install XP. My former Intel board had no such problem.
Anyone have experience with any of this on these boards? I realize I'm using a lot of accessories so yeah, it's complicated. I can provide more info if needed. System config is in my sig.

i just want to know the bios version you are using now. you may check the bios version if POST one screen. The reason why I asked is what you 've written in the additional Options: don't flash the bios to version 3.2. As far as I know the latest bios version for P4N Diamond is 1.4 when I searched on MSI website. You may check here. So I am very confused, could you help me?

P4N diamond sata problem

Hi
I got a big problem with my P4N diamond motherboard, my problem is the nvidia sata controller, when I connect a sata drive in slot 1- 4 the system hangs with a black screen just before windows boots, if I turn on raid the system boots with no problem, but I don’t wanna have raid, I have tried different sata harddisks with the same problem, so I know that is not the drive that is the problem and also if I put the drive in slot 5-6 ( Silicon image controller ) the system boots with no problem
So my question is how do I setup my system right or is there something wrong with the controller
Thanx

All drivers is installed, and I cant boot with cd-rom or anyting when the harddisk is set to nvraid controller and the nvraid is disable, if I enable nvraid and enable all 4 sata drives and disable pata on the drives the system boots with no problem, but as I don’t want my drives raided, so I got a problem I think there is something wrong with the controller ?
I have tried segate, Maxtor and wd drives but the same thing happens

P4N Diamond SATA Problem after Bios Update HELP!

I updated the bios correctly & now my SATA harddrive won't recognize.I put the drive in another pc (with the exact same setup..a p4n diamond etc) and it works no problem.The bios settings are set exactly as they were before the flash as i wrote them down!.
I have noticed there is an extra setting added in the bios ,something in the cell menu named CPU ratio unlock.
I have also noticed that my other pc (the working one) will no longer connect to the net if my network cable is plugged in my router from the pc with the bios update.As soon as i unplug the cable it connects.
I got the latest bios for the board is there something different in the bios from previously i need to do?
Like i says the bios settings i have put exactly the same as they were before the update.My windows (on the SATA drive) booted fine before the update and now it won't.
I updated the bios correctly and cleared cmos afterwards.Everything i should have done i am guessing i done.
Can somebody please help me on this.
Thanks
Decided to reflash the bios to version 1.4
Now the harddrive is recognised but windows will not boot (blue screen before it boots with the usual to prevent damage to your computer etc etc)
I am now formatting the harddrive & reinstalling windows.It seems MSI have issues with bios updates for this board which they should maybe bring out a new bios fixing this problem as it sure is a problem.

RE flashing the bios.I did this to try and fix a problem with windows not turning off when shutting down.I pc does the other does not & both have the same board and now the same version bios & also a freshly installed windows.I noticed power options in windows are not the same.How can this be.The boards are the same.
Anyway here are the specs of pc1 & pc2:-
pc1 (the working fine pc):-
P4N diamond bios ver 1.40
P4 SKT 775 Prescott 3.6ghz
2gb kingston ddr2 (dual channel)
1x 200gb maxtor IDE hd
2x 160gb maxtor SATA hd
Ati Radeon x600 gfx
pc2
P4N diamond bios ver 1.40
P4 SKT 775 Prescott 3.4ghz
512mb crucial ddr2 (1 stick single channel)
1x SATA2 16mb cache hd
nvidia quadro gfx
As you can see,not much difference between the 2.

[nVidia Series] P4N Diamond --PSU Problem, help me select

ok I finally am 100% sure it's my PSU tahts giving me the freeze/fallout things.
so now I'm going to buy a new PSU but I cant decide which one ..
these are the ones I was thinking about to replace my Ultra X-Connect UV BLue
(I'll give you my system setup first to see what I need)
Intel Pentium 840 EE 3.2Ghz Dual-Core Hyper-Threading
MSI P4N Diamond
1x Corsair ValueRam 512MB DDR2 (soon replacing with GEIL PC2-5400 667MHz DDR2 Ultra Dual Channel 1GB Kit 2*512)
1x MSI NX7800GTX 256MB
1x WD Raptor 10k RPM 36GB Sata
1x Maxtor 300GB 7200rpm Sata
1x Maxtor 200GB 7200rpm IDE
1x Plextor 16x DVD+/-RW DL
and if I forgot anything, ask me
comparing these PSU's atm.. price doesnt matter, I just need the best one out of these, or an even better one in the same price range
Enermax Liberty 620W
http://www.enermax.com/english/product_psu_liberty620w.htm
Sunbeam NUUO 550W
http://www.sunbeamtech.com/PRODUCTS/Power-supply/NUUO/nuuo-550.htm
Hiper Type-R 580W
http://www.hipergroup.com/English/products/hpu-4s580.html
help me decide pls, tnx :D

Quote from: MooZleZ on 24-November-05, 00:06:38
ok I finally am 100% sure it's my PSU tahts giving me the freeze/fallout things.
Just wondering what makes you 100% that its your PSU? Did you find some information or trobbleshoot...? Please make sure that you post back with results of a new PSU.
Thanks

Touchpad problems ((and other Windows 10 issues)

I upgraded to Windows 10 pretty smoothly, but I'm experieiincing the same problems as others when it comes to using tablet mode etc. My biggest frustration though is that the touchpad no longer consistently supports two-finger scrolling, which is sooo frustrating. Also, edge-swipe gestures to bring up things like the app-switcher and charms bar (is it still called that?) don't work either. I've updated to the latest drivers (all of the ones that Lenovo has at ths point) and that doesn't seem to fix any problems. Anyone know how to solve the touchpad issues? Also, seriously disapponted with the Lenovo support on these issues. The Yoga went from being one of my favorite laptops to being one of my least favorite with this OS "upgrade" and next time, I'll probably get a computer from Dell.

Hi, I too was experiencing simlar frustrations on my Flex 2-15" which uses a similar touchpad, the movement would even stop all together for about 15-20 secs, extremely frustrating!! Since my wireless mouse would work just fine I knew it had to be an issue with the drivers. So the updated driver version for win 10 min my case is going from v17(win8) to v19+(win10). I noticed that the Device Manager driver was showing that new version but the Synaptics control panel was reading that the driver was still 17 which I could see might cause issues for the hardware input to be read properly. Here is how I fixed it: 1) If you haven't already, download the windows 10 driver for your specific computer/ trackpad from this site. 2) Go to your device manager cpl and expand the pointer mouse objects and uninstall all of the drivers but DO NOT reboot immediately. 3) Goto the Programs and Features cpl and uninstall the Synaptics program (or ELAN / Alps depending on your stock controller app) 4) Reboot when prompted. 5) Run the download in step one and install the driver and Synaptics app when prompted NOTE: In my case the Synaptics install would not open on its own and had to open it's setup.exe manually <<C: drivers\Touchpad Driver(Elan, Synaptics, ALPS)\2al301af\Synaptics>> If you still have the issue, try running through the steps while disconnected from the internet. It might be auto-updating with the wrong data. I hope this helps those afflicted my this annyoing issue.~gC

Adding a RAID card to help speed up export (and other drive question) in Premiere Pro CC

First of all, I have read Tweakers Page exporting section because that is where my primary concern is. First my questions, then background and my current and proposed configurations:
Question 1: Will adding a hardware RAID controller, such as an LSI MegaRAID remove enough burden from the CPU managing parity on my software RAID 5 that the CPU will jump for joy and export faster?
Question 2: If true to above, then compare thoughts on adding more smaller SSDs for either a one volume RAID 0 or smaller two volume RAID 0 to complement existing HDD RAID 5. That is, I'm thinking of buying four Samsung 850 Pro 128 GB SSDs to put in a four disk volume to handle everything (media/projects, media cache, previews, exports), or split it up into two volumes of two disks each and split the duties, or keep the four disk volume idea and put the previews & exports on my HDD RAID 5 array.
The 850's are rated at SEQ read/write: 550/470 MB/s thus I could get around 2000/1500 MB/s read write in a four disk RAID 0 or 1/2 that if I split into two volumes to minimize volumes from reading/writing at the same time, if that really matters with these SSDs?
The Tweaker's page made a few comments. One is splitting duties among different disks, rather than a large efficient RAID may actually slow things down. Since the SSDs are much faster than a single HDD, I'm thinking that is no longer accurate, thus I'm leaning toward the Four disk configuration putting OS & Programs on C drive, Media & Projects on D (HDD RAID 5), Pagefile & Media Cache on SSD (2-disk RAID 0) and Previews &Exports on 2nd SSD RAID 0 (or combine the two RAID 0's and their duties).
Just trying to get a perspective here, since I haven't purchased anything yet. Any experience/stories, I would appreciate.
My current drive configuration:
My D drive is software RAID 5 consisting of four 1 TB Western Digital RE4 (RED) 7200 RPM HDDs with a CrystalDiskMark SEQ Read/Write of 339/252 MB/s.
The C drive is SSD 500 GB (Samsung 840 (not Pro) and does 531/330 MB/s. My OS, Program Files and Page File are on C, and data/media files/project, etc all are on the RAID drive.
Problem:
Current setup allows for smooth editing, only the exporting seems slow, often taking between two and two and a half times the video length to export. Thus a 10 minute video takes 20-30 minutes to export. 15 minute video can take 30-40 minutes to export. The first 10% of the two-pass export takes under a minute (seems fast), but it gets slower where the final 10 or 20% can hang for many minutes like my system is running out of steam. So where is the waste?
I have enabled hardware acceleration (did the GPU hack since my GPU isn't listed) and it may spike at 25% usage a few times and eat up 600 MB of VRAM (I have 2 GB of VRAM), otherwise it is idle the whole export. The CPU may spike at 50% but it doesn't seem overly busy either.
Our timeline is simple with two video streams and two audio streams (a little music and mostly voice) with simple transitions (jump cuts or cross dissolves). We sometimes fast color correct, so that might use the GPU? Also, since we film in 1080 60P and export 1080 29.97 frames/sec, I think that is scaling and uses the GPU. I know without the GPU, it does take a lot longer. I have ruled out buying a faster GPU since it doesn't appear to be breaking a sweat. I just need to know if my system is bottlenecked at the hard drive level because I'm using software RAID and my disks are slow and will hardware RAID significantly reduce the CPU load so it can export faster.
Our files are not huge in nature. Most our clips are several MBs each. Total project files are between 5 GBs and 10 GBs for each video with Windows Media File export being 500 MB to 1.2 GB on average. We shoot using Panasonic camcorders so the original files are AVCHD, I believe (.MTS files?).
Considerations:
1. I'm thinking of buying (and future proofing) an LSI Logic MegaRAID 9361-8i that is 12Gb/s SAS and SATA (because some current SSDs can exceed the 6Gb/s standard).
2. I'm not replacing my current RAID 5 HDDs because not in my budget to upgrade to 6 or more large SSDs. These drives are more important to me for temporary storage because I remove the files once backed up. I don't mind a few inexpensive smaller SSDs if they can make a significant difference for editing and exporting.
I can only guess my HDD RAID is slow but the CPU is burdened with parity. I would imagine running RAID 10 would not help much.
My setup:
my setup:
CPU - i7-3930K CPU @4.5 GHz
RAM - G.SKILL Ripjaws Z Series 32GB (4 x 8GB) DDR3 2133 @2000
Motherboard - ASUS P9X79 WS LGA 2011
GPU - Gigabyte GeForce GTX 660 OC 2GB (performed the compatibility list hack to enable hardware acceleration).
C drive - 500 GB Samsung 840 SSD (Windows 7 Pro 64 bit and programs).
D drive - four 1 TB WD RE4 Enterprise HDDs 7200 RPMs in software RAID 5
Case - Cooler Master HAF X
CPU Fan - Cooler Master Hyper 212 EVO with 120 mm fan
Power Supply - Corsair Pro Series AX 850 Watt 80 Plus Gold
Optical Drive - Pioneer BDR - 208DBK
thanks in advance,
Eric

........software RAID 5 off the motherboard ??????......NOT a good idea, from what I have read here on this forum from experts like Harm Millard and others. They have mentioned a LARGE overhead on the CPU doing this....causing sub-par performance. RAID 0 off the motherboard will NOT do this, however.....RAID 0 would provide optimum speed, but, with the risk of total data loss if ANY drive fails. You may wish to reconfigure your RAID to be RAID 0...BUT...you would need to DILIGENTLY back up its entire volume onto perhaps a quality 4TB drive very frequently.
A lot depends on the nature of your current and FUTURE codecs you plan to edit. You may not want to sink a lot of money into an older setup that may have trouble with more demanding future codecs. For now, in the 1080p realm, your rig should be OK....the read/write performance on your CURRENT RAID 5 setup is not great, and a definite drag on the performance. The rest of your components appear to be fine.....the Samsung SSD, though not ideal, is OK.....it's write speed is WAY lower than the Pro model,but, the drive is used mainly for reading operations. Since you have Windows 7 Pro, and NOT Windows 8.......you CAN put the entire windows page file onto the RAID 0 you might create.....this will take that frequent read/write load OFF the SSD. Read the "tweakers Page" to see how to best TUNE your machine. To use your current setup most efficiently, without investing much money, you would :a. create the RAID 0 off the motherboard, ( putting all media and project files on it ) b. install a quality 7200rpm 4TB HDD to serve as a BACKUP of the RAID array. Then, install a Crucial M550 256GB or larger SSD, ( close in performance to Samsung 850 Pro...much cheaper), to put all previews, cache , and media cache files on....AND to use as " global performance cache" for After Effects...if you use that program. Exporting can be done to ANOTHER Crucial M550 for best speed...or, just to the either the FIRST Crucial or, the 4TB drive. Your current GPU will accelerate exports on any video containing scaling and any GPU accelerated effects. Your CPU is STILL important in SERVING the data to and from the GPU AND for decoding and encoding non-GPU handled video....your high CPU clock speed helps performance there ! You may want to check out possibly overclocking your video card, using MSI Afterburner.or, similar free program. Increasing the "memory clock speed" can RAISE performance and cut export times on GPU effects loaded timelines,or, scaling operations. On my laptop, I export 25% faster doing this. With my NEW i7 4700 HQ laptop, I export in the range of your CURRENT machine....about 2 to 3 times the length of the original video. PROPERLY SET UP...your desktop machine should BLOW THIS AWAY !!
Visit the PPBM7 website and test your current setup to possibly identify current bottlenecks,or, performance issues. THEN, RE-TEST it again, after making improvements to your machine to see how it does. Be aware that new codecs are coming (H.265 and HEVC,etc.) which may demand more computer horsepower to edit, as they are even MORE compressed and engineered for "streaming" high quality at a lower bandwidth on the internet. The new Haswell E...with its quad-channel memory, 8 core option, large number of PCI gen. 3 lanes, goes farther in being prepared for 4K and more. Testing by Eric Bowen has shown the newer PPro versions provide MUCH better processing of 4K than older versions.

Leopard, gcc 3.3 and other bizarre questions...

Hi all.
I'm currently trying to install amarok music player onto Mac OS X 10.5.2,
I've already done so on an identical hardware configuration, under Mac OS X 10.4.x, and after a few compiling errors, and unmet dependencies, managed pretty well I thought.
This time my problem(s) is(are) different.
I've user what the amarok wiki ( http://amarok.kde.org/wiki/OnOSX ) describes as the "Amarok via Fink in complete" method, which is to say install fink, hit fink install amarok, and hope for the best... Having pushed through a few bits and pieces here and there, amarok is now compiled and installed.
But I get this strange error message when launching amarok, which then subsequently and very rapidly crashes :
[start code]
dyld: lazy symbol binding failed: Symbol not found: dscaler_greedyh_getmethod
Referenced from: /sw/lib/xine/plugins/1.1.10/post/xineplugposttvtime.0.0.0.so
Expected in: dynamic lookup
dyld: Symbol not found: dscaler_greedyh_getmethod
Referenced from: /sw/lib/xine/plugins/1.1.10/post/xineplugposttvtime.0.0.0.so
Expected in: dynamic lookup
[end code]
(I don't think the entire amarok debug output is relevant, it's just version 1.4.8 and the rest seems pretty standard to me, do please ask if you want the full gdb output though)
After looking up the dyld errors I found this :
http://naranja.umh.es/~atg/blog/archives/2007/01/entry_0.html
(quite old I know, but sound and the closest I found to my error)
which lead me to believe I should have compiled amarok, and for that matter libxine1 (which I compiled myself with the --with-external-ffmpeg flag because fink wouldn't do so...), with gcc set to version 3.3 (should I?)
I then discovered that gcc_select didn't exist in Mac OS X 10.5, nicked it of a 10.4, removed and tweaked it until everything worked fine on the 10.5 with gcc 3.3 (I compiled a test.c with no problem), and tried again... with no luck. I couldn't get xine, nor amarok to compile.
So my questions are these (after that lengthly introduction, bear with me please :
-firstly (or miraculously...) does anyone recognize or understand those errors amarok is giving out?
-secondly can someone please explain the situation with Mac OS X 10.5 and gcc versions <=4.0 'cos I'm really out of the picture here ?!
Thanks a lot in advance for any help, and sorry for the long post, I figure it's always best for folks to have an overall picture of things...
Kind regards,
Mark.
Message was edited by: Marcool

I quote :
Re: Mac OS X 10.5 ? gcc 3.3 ? and other strange happenings
From: Benjamin Reed ([email protected])
Sent: Mon 24/03/08 15:51
To: Mark COLLINS ([email protected])
On Mon, Mar 24, 2008 at 6:01 AM, Mark COLLINS <[email protected]> wrote:
start code
dyld: lazy symbol binding failed: Symbol not found:
dscaler_greedyh_getmethod
Referenced from:
/sw/lib/xine/plugins/1.1.10/post/xineplugposttvtime.0.0.0.so
Expected in: dynamic lookup
dyld: Symbol not found: dscaler_greedyh_getmethod
Referenced from:
/sw/lib/xine/plugins/1.1.10/post/xineplugposttvtime.0.0.0.so
Expected in: dynamic lookup
end code
I'm sorry, I can't really help with xine issues, you'll have to
contact the xine maintainer.
As for getting amarok 1.4.x, if you want 1.4.8, I've already got
amarok 1.4.8 in fink unstable, your best bet is to not try to build it
by hand, and instead get it there...
-firstly (or miraculously...) do you recognize or understand those errors
amarok is giving out?
I recognize them as an issue with xine, but I don't know where the
errors come from.
-secondly can you explain the situation with Mac OS X 10.5 and gcc versions
<=4.0 'cos I'm really out of the picture here ?!</div>
gcc 3.3 does not exist on any of the intel platforms, except for
compiling backwards-compatible powerpc code. The first apple gcc that
supports x86 Mac OS X is gcc 4.0. You can't gcc_select it, if there
is something that supposedly requires 3.3, it won't work on 10.4 or
10.5, on an intel box, except building a complete powerpc application
and running it under rosetta.
Benjamin Reed a.k.a. Ranger Rick
Fink, KDE, and Mac OS X development
http://www.racoonfink.com/
So thanks a lot Benjamin, that solves that, no way to run gcc 3.3 on Intel Mac OS X 10.5, and the errors I'm encountering are from xine.
I guess I'll be chasing up the xine maintainer now!
Thanks all for you help guys, and see ya' !
Regards,
Mark.

How does Smartware handle backing up two drives to My Cloud...and other Smartware questions

When you set up backup from two disk drives on one PC to My Cloud via Smartware, do they both backup simultaneously, or do I need to do one, then the other? I have a Windows 8.1 laptop with two hard drives, one is 500GB, the other 1 TB. After installing My Cloud (3TB) and Smartware, I went into Smartware and set up my backups. I selected various folders on each drive to back up, and I also set up two different folders on My Cloud to receive these files. Setup is like this: PC Drive -> My Cloud FolderSeveral folders in G: drive -> Pictures, Video folder on My CloudDesktop and User folder onmain drive -> Users folder on My Cloud Every time I open my PC at home, I start Smartware, click the Backup tab and let the backup continue. I feel like I need to manually go into the Home and Backup tab for each backup plan (one per drive) and restart it. Regardless, my question is this: is Smartware able to handle these two drives on my laptop backing up onto My CLoud? Other Smartware questions:- Does my PC have to be on my home network (where My Cloud is installed) in order to run Smartware? Can I be on the internet outside of my home and run Smartware?- I run Outlook 2010. Will Smartware back up the latest Outlook file automatically as new files are created (basically, every time I run Outlook)? Much appreciated. - Paul M.

Hello,
When you set up backup from two disk drives on one PC to My Cloud via Smartware, do they both backup simultaneously, or do I need to do one, then the other?
You will need to do one first and then the other and the last one that is selected will be done automatically.
- Does my PC have to be on my home network (where My Cloud is installed) in order to run Smartware?
Yes.
Can I be on the internet outside of my home and run Smartware?
WD Smartware does not perform remote backups.

Video and audio linking problem, and others?

So, I am having 2 main problems. When I first started using FCE everything was great. Then, I changed some settings, and for some reason, it doesn't work like I want it to. So, my first problem is linking. When I import, it is automatically unlinked, but I think FCE thinks that it is! When I do press Apple L (shortcut to link video and audio) it still isn't linked! How can I get it to link?
My 2nd problem may be linked to the first. When I want to make a cut right on the playhead, it is really hard to get it on the playhead. Previously, it would just snap on the playhead if I got close, and now it doesn't! How can I get it to snap better?
Thanks for all the help!

1) Make sure linking (Shift-L) is turned on before you add your clip to the timeline. To manually link audio tracks to your video tracks select the two and go to +Modify > Link+ (Command-L).
2) Make sure snapping is turned on in the timeline. Hit the "N" key to toggle it on or off.

OJSP classpath problems and other OJSP issues

Hi,
We are running into a number of OJSP problems. The technology stack we are using is :
Apache 1.3.12
Jserv 2.0
Jswdk 1.0.1
OJSP 1.0.0.6
The issues we have are:
1) The OJSP classpaths mechanism as described in the documentation does not work. In our configuration, globals.jsa resides under apache/htdocs. The WEB-INF directory also sits under apache/htdocs.
It seems that OJSP completely ignores WEB-INF/lib. Any jars that the JSP may need have to be put on the servlet classpath (wrapper.classpath).
OJSP will pick up modified beans from
WEB-INF/classes but only for beans that
use JDBC with thick drivers or for beans
that don't use the JDBC driver at all.
2) We got our application to work by moving everything that the JSPs may need to the servlet classpath. However, OJSP would hang when switching between various JSPs. Stopping apache in this case also caused the port to be held by some runaway process. We then had to start apache on a different port.
So our questions are:
1) Is OJSP going to support thin JDBC drivers?
2) Are there other ways of getting bean reloading to work? Bouncing the server, everytime a bean changes is not a viable option for us.
3) Are there any known issues with OJSP hanging when navigating from page to page?
Thanks,
Munazza

Originally Posted by zdenca
Hi, we got 2 node cluster Netware6.5SP8 or (OES) we lost the sbd partition and could not mount or start clustered volumes and could not recreate the sbd partition.
So I have created a new cluster and was able to create sbd partition and mount the clustered partitions manually.
But not we see 2 cluster objects in C1 the old one is complaining with the NDS sync for the GroupWise pool and master ip resource says new node under location.
The new cluster objects see the servers properly but no cluster volumes and I cannot create any.
Nssmu under both servers sees the clustered volumes properly. Check volume objects and trustees under Dsrepair sees only sys.
So how do I make everything work under the new cluster?
Help would be greatly appreciated.
Thanks M.
Well could not find the cluster forum :(
Anyhow this is the fix: Deleted all old cluster objects from C1 recreated e-dir objects for clustered pools with nssmu which published the correct clustered info in C1, and allowed me to create new cluster volumes in C1, under the new cluster.
But took me much longer than type these 3 lines:)
Cheers.
M.

Posible p4n diamond heat problem and other beep question

Similar Messages

Maybe you are looking for