Possible slice change needed for boot???

One of our servers went down a week ago. I narrowed down to a bad hard drive. I received a new drive but I REALLY need the data off the old drive. I had another bad drive laying around so I swapped the controller cards and i was able to boot up. Now I receiving "/dev/dsk/c1t1d0s1 No such device or address. I then booted from the CDROM using the Solaris 8 install disk and ran format. The menu identified the drive as c2t1d0.........i'm guessing because the the controller card change.
How do change this to look at c2t1d0 at boot??
Thanks in advance.

Hello experts,
any ideas?
I need aswell to change the permission in the UME repository...
Thanks in advance!
Greets
Thomas

Similar Messages

Mass change needed for document properties

Hello Techies,
My users want to upload large amounts of documents and want they also want to set the properties in bulk and not one by one. I have made some properties for these documents.
The problem is that the mass change report in the portal is not user friendly enough. They want to select a few documents and set them all to the same properties. Webdav does not support this either, nor does DAV explorer.
Other suggestions?

Frederik - there is <a href="https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/9bfc45ba-0b01-0010-4890-da85753f0f58">an article by Martin Hermes about using Excel for property maintenance</a> that outlines one possible custom solution for this. You might find that the Excel sheet as it is delivered fits your needs - you may also find that you need to modify it for your requirements.

Bitlocker: Is it possible to change the pre-boot screen?

Hi,
Very simple question but I cannot seem to find any information, is it possible to customise the Bitlocker pre-boot screen so I can have my own company logo on it?
Thanks

Hi,
For this issue, i think we cannot do this since bitlocker tool will add to BIOS before system start, so we we protect the data on volumes include non-system volume, here is the detailed information:
http://technet.microsoft.com/en-us/library/cc732774.aspx
http://technet.microsoft.com/en-us/library/hh831507.aspx
For customise logo screen, please refer to the below link:
http://social.technet.microsoft.com/Forums/windows/en-US/911ac246-3196-41fa-ac7a-0227910985ad/company-logo-on-login-screen?forum=w7itprogeneral
Hope this helpful.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

Doc for changes needed for RIDC going from folders_g to framework folders?

Greetings,
Is there any documentation on the potential changes that are needed to be made by a RIDC client when going from a folders_g implementation to a framework folders one?

Hi ,
Changes to the code will be on the service side where in the Folders_g service calls need to be replaced with Framework Folders . Documentation for the FF services are :
http://docs.oracle.com/cd/E23943_01/doc.1111/e11011/c08_frameworkfolders.htm#CHDHIHDI
Apart from that I don't think there should be any other major changes that need to be done to the code .
Let me know if this helps you .
Thanks
Srinath

Is it possible to change settings for an existing sequence?

I am cutting a short "crowd-sourced" class play, shot by parents. I have 4 different types of footage from 4 cameras: Two are 720p (30p), one is a 640x480 .mov and the other was shot in 720p but burned to a PAL DVD so they are .VOB file rips at 25fps, 720 x 576 w/1.2 widescreen.The main camera is an .MTS file (AVCHD 720p)
Since I am planning on ultimately making widescreen NTSC DVD's, I sync'd the cameras in a widescreen-DV sequence, then nested that into a new widescreen-DV sequence and activated the multi-cam. I did all of my actual editing in the new muti-cam sequence - but now I am thinking that I should have started with an AVCHD 720p sequence to sync cameras and just maintained 720p thoughout - until exporting the MPEG-2 file for the DVD.
I can make a new 720p sequence and cut/paste everything from my timeline - but they would still be nested multi-cam cuts that link back to the original widescreen-DV sequenece I setup to sync the 4 cam views. I cannot seem to change the settings for the existing sequence - so is there maybe a workaround for what I am trying to do? Essentially, to trick the new 720p sequence (with all the actual multi-cam edits pasted into it) to linking to a new 720p sequence with the already sync'd cam footage pasted into it? And secondly, will it actually effect the quality of the final DVD output? I may also want to make a 720p web version for Vimeo if feasible...
Any help would be greatly appreciated.

I have created the new 720p AVCHD and cut/pasted all of my edits. That is not the problem.
Almost of my edits (other than a few titles amd stil pics I added) are cuts from the original nested sequence called (4-CAM SYNC). It is a regular NTSC widescreen sequence. In this original sequence, I am scaling the the cameras down to fit the frame and sync'ing the four cameras. I am attempting to get this new sequence to link to a new 720p nested sequence that has my sync'd cam footage - to replace 4-CAM SYNC on the time, while still retaining all the edits I have made - I will just have to change some of my scaling settings in a few clips.
It sure would be easier if I could change the "Editing Mode" parameter under Sequence Settings...

Change permissions for UME repository

Dear friends,
Is it possible to change permissions for the ume repository. By default, it has "Allow" permission for List Children and Read properties. I dont see any options to change permissions under Settings -> permissions. Does anyone here in this forum knows how can I achieve the same? I am actually trying to index the ume repository and the crawler fails. I was wondering if the repository needed to have a full control. So, I am trying to change the permissions.
We are on EP6 SP13 (all components)
Any help is appreciated,
Thanks,
Mandar

Hello experts,
any ideas?
I need aswell to change the permission in the UME repository...
Thanks in advance!
Greets
Thomas

Backend Purchase Requisition - is it possible to change price?

Hi,
We are using classic scenario (SRM 4.0 - R/3 4.7), and, after the transfer of the PR to the backend system, the "Price" field in ME51N is non-changeable. Is it possible to change price for items in the backend purchase requisition after it was transferred from SRM system?
thanking you in advance,
Andrey.

Hi Andrey
One the Pr is generated in R3 backend system we can change the price field and this can be regulted by field status group where you have to keep the option optional for price field rarther than display .
This is in MM -spro - Manterial Management - Purchase requisiton- Define Screen Layout at Document Level
regards,
Nimish Sheth
Do reward points for helpful answers.

EDI/IDOC changes required for Unicode migration

Hi Everyone,
We are planning to migrate our R/3 box to Unicode and have got suffiecient documents regarding the changes needed for the ABAP programs. But the EDI and IDoc process is proving to be a grey area in this regard. I would be thankful if some one can send the related documents.
email [email protected]
Thanks,
Vinay

If you have VS .NET 2003, then all you need to do is install CR XI Developer. I would not recommend using the RDC in.NET for two basic reasons:
1) The RDC has not been tested in .NET (thus no escalation is available for any fix issues)
2) The RDC has been retired in CR 12. This may have implications for the lifecycle of your project...
To see how to use the RDC in .NET, check out the article [Using the Report Designer Component in Microsoft Visual Studio .NET|https://www.sdn.sap.com/irj/boc/index?rid=/library/uuid/f0751a7f-a81d-2b10-55a0-e6df0e1bab6d&overridelayout=true]
My recommendation would be to use the CR assemblies for .NET. The following resources should get you going:
[Sample applications|https://wiki.sdn.sap.com/wiki/display/BOBJ/CrystalReportsfor.NETSDK+Samples]
[Crystal Reports For Visual Studio 2005 Walkthroughs|https://www.sdn.sap.com/irj/boc/index?rid=/library/uuid/2081b4d9-6864-2b10-f49d-918baefc7a23&overridelayout=true] (most of the concepts will apply to .NET 2003)
[Advanced use of Crystal Reports for Visual Studio .NETu2019s feature set and object model|https://www.sdn.sap.com/irj/boc/index?rid=/library/uuid/702ab443-6a64-2b10-3683-88eb1c3744bc&overridelayout=true]
Developer libraries:
https://boc.sdn.sap.com/developer/library
http://devlibrary.businessobjects.com
Also, ensure you apply the latest CR XI r1 [Service Pack|https://smpdl.sap-ag.de/~sapidp/012002523100006008952008E/crXIwin_sp4.zip]
Ludek

Change Style for text (PE12)

When I insert a text, i can change style just one time. It is not possible to change style for other text. I must stop the program and start up for changing style at each time I request to change style.
Solution?

Peru Bob,
Thank you for linking to the Muvipix thread. Not sure what happened in PrE 12, but this Styles Bug looks pretty serious, as Styles allow a user to do so much, regarding attributes for Shapes and Text.
Appreciated,
Hunt

Changing defualts for options on far left of timeline

hi everyone. Anyone know if it's possible to change defaults for the options available under the arrow facing right on the far bottom left of the timeline? I'm sorry if there is a word for these options that I'm not aware of. I'm talking about 'Show video film strips/Show audio wave forms/show through edits...'
I would like to have 'show duplicate frames on whenever I create a sequence, rather than have to select it every time. Thanks in advance for any advice.

In the top left of your screen, in the menu Choose FINAL CUT PRO > User Preferences > go to the 'Timeline Options'-tab...
Set your desired settings.
That will apply to everey newly created sequence...
Rienk

I have a iMac 21,5" Intel mid 2011 and I need to know if is possible I change the original 500Gb HD for a 512Gb SSD? If yes, where I find a tutorial about this? Thanks a lot and best regards all.

Hi people,
I'm typing from Brasil, sorry my English.
I have a iMac 21,5" Intel mid 2011 and I need to know if is possible I change the original 500Gb HD for a 512Gb SSD?
I intend to keep the original DVD driver and install the SSD in the same HD place.
If yes, where I find a tutorial about this?
And I will like to know if the 512GB Solid-State Drive Kit for Mac Pro is compatible with iMac.
http://store.apple.com/us/product/MC731ZM/A/512gb-solid-state-drive-kit-for-mac- pro?fnode=5f
What brand and model of SSD do you recommend?
Thanks a lot for now and best regards all.
Carlos Sgrillo
Porto Alegre, RS, Brasil

Tukaine
Sep 23, 2012 10:59 PM
Since the late 2009 iMacs came out, replacing the hard drive has caused the internal Hard Drive Fan to start running at around 6000RPM.
This is due to Apple replacing the external Hard Drive temperature sensor with a proprietary firmware and using the drives internal sensor.
Replacement drives do not contain the firmware to deliver temperature data on the temperature sensor cable.
When the iMac does not receive a good signal from the hard drive it puts the fan at full speed to protect the drive.
If you replace your drive, your iMac will initially seem fine, but soon the fan will begin to speed up to full speed. Resetting the SMC (System Management Controller) will have a temporary effect, but again the fan will speed up.
Fixes people have used in the past included:
Using smcFanControl and the terminal to set a MAX speed for the fan and writing scripts to start this after every sleep/restart.
Shorting the temperature sensor cable (Not a possibility on 2011 iMacs) this tricks the iMac into thinking the drives temperature is very low, hence slow fan speed.
Both these fixes are less then perfect and leave the drive in a dangerous situation with no protection from overheating.
Another option people try is other Fan Control software. These programs will not work for this particular issue as they often only control the base speed, and if they do control the fans actual speed they rely on the temperature reported by the sensor which is now incorrect.
HDD Fan Control
HDD Fan Control works to fix this issue by reading the drives internal temperature using the S.M.A.R.T protocol and set the fans actual speed to a value good to protect the drive.
It runs at startup and continually to always control the fan correctly, prevent the loud fan noise and protect the drive from overheating
Instead of HDDFan Control, get the free SSDFan Control
http://exirion.net/ssdfanctrl/

Disk Utility: For one Disk it isn't possible to change anything

Good Morning everybody
First I think my Spec's are important:
MacBook Pro (13-inch, Mid 2012)
2.9 GHz Intel Core i7
16 GB 1600 MHz DDR3
Two Disks: Samsung SSD 840 EVO 250 GB (normal Startup Disk)
Toshiba HDD 750 GB
Intel Hd Graphics 4000 1024 MB
OS X Yosemite Version 10.10.1
And now to the thing I did that the Problem appeared:
After a very long discussion with the Apple Support Help Hotline I decided that, after a Backup, I wil do this: OS X Mountain Lion: Erase and reinstall OS X to try something out, and then will restore my backup.
It all went perfect till the thing with restoring my backup. In the Menu I get when I press (CMD + R) I tried to restore the backup. But then, in the middle of the process, the system cancelled the process automatically and shut down. So I started the Mac again, it automatically came into this CMD + R menu. So I went into the Disk Utility to watch what happened. Since then my two Disks are shown the same way (picture): It is not possible to change anything, except running the First Aid thing. Luckily it was possible to install the OS X and my Backup on the HDD, but for me this is only a temporarily version because the SSD is at the moment completely blocked.
Goal:
It would be great when I can add/remove/change partitions on both Hard Disks and when, at the end, it would be possible to install my Backup to the SSD and use the HDD as a "external Storage" again.
Thanks for all your responses & you can ask me everything if you need more information.
David

This solved my problem.
http://derflounder.wordpress.com/2013/06/29/erasing-a-filevault-2-encrypted-volu me/

Am creating document with Pages. pages are in "portrait" orientation, but two charts at end need to be "landscape". changing the orientation for one section changes it for entire doc. can i have different orientations in Pages for different sections?

am creating a document with Pages. all pages using "portrait" orientation, except 2 appendices need to be in "landscape". in Word for Windows it is possible to have different page orientations for different sections of a document. is that possible with Pages. Even when i put the appendices in a different section, changing the page orientation changes it for the entire doc.

Make a separate document the size and orientation you want.
Turn that into a pdf and add it back into the original Pages document or into the pdf from from that document.
Peter

Is it possible to change the read/write permissions on a time machine back-up of iTunes? I need to restore it, but old version is locked....

Is it possible to change the read/write permissions on a time machine back-up of iTunes? I'm needing to restore it as my phone deleted half our playlists during sync & am not seeing a way to unlock the permissions. I have the current version unlocked, but can't seem to get the backed-up version. When I click on restore I get a pop-up that says iTunes can't be deleted as it is part of the OS. I'm not even trying to delete, just restore the old version. Any suggestions?

Hmmm, ok I'll give it a shot. I've always had the iTunes sync w/ my phone set up to only load selected playlists to the phone b/c there's a lot more in iTunes than I have room or desire for on my phone. A few months back I started having trouble w/ trying to sync everything & subsequently adding more to the phone than it could hold. The quickest thing at the time was to unclick the sync music option in iTunes so I could still backup the phone to the computer & not have a problem.
When I asked about it during one-to-one session shortly after, they advised me to delete the music off my phone & then re-sync it to the computer, run a backup of the phone & redownload the music to the phone. When I tried this it ended up deleting all my playlists (but not my husband's) from iTunes. Irritating, but I've been rebuilding the playlists since. I had also unclicked sync music again & an Apple person told me the most likely best fix was to delete & reload iTunes completely.
A few days ago I realized I hadn't backed up the phone to the computer in over a month so after deleting & reinstalling iTunes, & w/o changing anything (sync music was STILL unchecked) I ran a backup & my phone went from having 4 GB free space to being 2 GB over capacity due to iTunes trying to download the entire music library to the phone. I made a one-to-one appt again & it was suggested AGAIN that I delete all the music off my phone & then resync it to the computer & redownload the music. We did this (though a few random songs that had previously been purchased somehow remained on the phone), I got home, connected the phone & instead of the music that shows as 'on my device' disappearing from iTunes it just sat there, so, as the guy had told me I MIGHT have to do, I threw all those songs showing in iTunes as being on my phone, in the trash so that it was completely clear.
At this point I checked sync music, made sure the options were 'selected playlists only', checked the ones from my own list that I wanted (I usually have one playlist of comedians from my husband's folder that I also have on the phone, but didn't check it at this point). It uploaded all my stuff just fine, but for whatever reason when it saw that I wasn't uploading that comedy playlist any longer, it not only didn't upload it but proceeded to delete my husband's entire folder of playlists from iTunes. -_- I got on the phone w/ an Apple support person right away but he wasn't able to tell me anything .. basically said we'll have to rebuild everything. I asked about the possibility of using time machine, he said he's not qualified to answer that, so that's when I started looking around online & found, among others, the link I referenced a couple replies ago.
I hope this all makes sense. It's been a long-term issue so I'm trying to go from memory as I figured to begin w/ that I had just made a mistake somewhere, so didn't try to document anything. Now w/ it having happened a 2nd time, I'm not sure if it was 'user error' or something else.......

TS1544 I am the administrator of my MacBook Pro, which I share with my kids. One of them forgot his password, so as the admin I changed it for his account, but when I try to see his account, it says I need to provide the keychain password. How can i get

I am the administrator of my MacBook Pro, which I share with my kids. One of them forgot his password, so as the admin I changed it for his account, but when I try to see his account, it says I need to provide the keychain password. How can i get it? I have no idea how to sort this out...

First, make sure caps lock is not on.
You must back up all data before continuing, unless you've already done so. If you need to back up but can't log in, ask for instructions.
If the user account is associated with an Apple ID, and you know the Apple ID password, then maybe the Apple ID can be used to reset your user account password.
Otherwise*, boot into Recovery mode. When the OS X Utilities screen appears, select
Utilities ▹ Terminal
from the menu bar. In the Terminal window, type this:
res
Press the tab key. The partial command you typed will automatically be completed to this:
resetpassword
Press return. A Reset Password window opens.
Select your boot volume ("Macintosh HD," unless you gave it a different name) if not already selected.
Select your username from the menu labeled Select the user account if not already selected.
Follow the prompts to reset the password. It's safest to choose a password that includes only the characters a-z, A-Z, and 0-9.
Select
 ▹ Restart
from the menu bar.
You should now be able to log in with the new password, but your Keychain will be reset (empty.) If you've forgotten the Keychain password (which is ordinarily the same as your login password), there's no way to recover it.
*Note: If you've activated FileVault, this procedure doesn't apply. Follow instead the instructions on this page:
If you forget the password and FileVault is on

Possible slice change needed for boot???

Similar Messages

Maybe you are looking for