Post Your HDTV display CONFIGURATION HERE.

In order to help others, can those who have full (or close) resolution of your HDTV post your display configuration here?
Please include your television model, OSX version, and list of an additional software/hardware used to get things working.
Thanks.

Toshiba 37WL58, Mac mini 1.5GHz Intel Core Solo, DisplayConfigX (registered), connected with the DVI to VGA adapter.
Verified DisplayConfigX settings:
Monitor Tab:
Refresh: 49.00 - 105.00
Horizontal Frequency: 12.00 - 85.00
Pixel Frequency: 350.00
Aspect Ratio: 4:3
Default Refresh Rate: 60
Resolution Tab:
Horizontal - Vertical
Active Pixel: 1360 - 768
The others are preset, but should read:
Front Porch: 64 - 1
Sync: 144 - 3
Back Porch: 208 - 23
Total: 1776 - 795
The refresh rate should default to 60.003
Afterwards, choose the Widescreen option on the remote.
(Thanks to Andyb2 over at AVForums.com and Mark Parsons1 at Apple Discussions)
Mac mini 1.5GHz Intel Core Solo Mac OS X (10.4.7)

Similar Messages

Post your questions about #BlackBerry10 here!

Hey everyone,
What a week last week! I think I'm finally starting to settle down after all the excitement with our global launch events last week.
If you're getting a BlackBerry 10 device soon, take a look at these tips on the BlackBerry Help Blog to help you set up your email, contacts, calendar and social networks: http://helpblog.blackberry.com/2013/01/blackberry-10-add-email-contacts/
Have other questions about BlackBerry 10? Our community can answer pretty much anything, just post your question below!
Remember, if you have a BlackBerry 10 device and need support, check out the BlackBerry 10 Support boards on the main page of the community.
^Bo
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Likes for those who have helped you.Click Accept as Solution for posts that have solved your issue(s)!

sanjithb wrote:
Why is the bis being stopped and not unlimited in south africa. Especially on the Z10.
the BIS is not stopped. BIS is still required for OS7 and previous.
the Z10 does not need a specific BIS plan, which is generally considered a very good improvement.
The search box on top-right of this page is your true friend, and the public Knowledge Base too:

Refurbished MacBook Pro Owners: Post your experiences with "Refurbs" here.

Hello Everyone. For the past few months I've been seriously thinking about getting a Mac notebook. When I get my Mac, I plan to run Final Cut Express HD for a few years, and If I decide to get a MacBook Pro then after a few more years I'll upgrade to Final Cut Studio. During my research of Macs I've stumbled upon something that really seemed to catch my eye; Refurbished MacBook Pro's for 41% Off Original Price. As far as I know, according to a few refurbished MBP owner's comments and Apple's brief description of it's "Stringement Refurbishing Process," it seems like a good deal to me, but of course it's always good to ask those who have already purchased a Refurbished MacBook Pro to see just how good of a job Apple does on refurbishing their products. That's why I've come here. For your comments. For all of you who have previously purchased a Refurbished MacBook Pro or other related item, please tell me about your experiences with your refurbished products. Was it a good experience? Or was it a bad experience, and feel free to go into as much detail as you need because I'll read your entire comment no matter how long. As you can see I'm pretty desperate for some owner's opinions so I will very much appreciate any comments that you give me. Thanks in advance for all your help and comments!

I received my refurbished 2.16GHz Macbook Pro on Tuesday and had a similar instance to Ty-Guy. My shipping box wasn't visibly damaged but the Macbook Pro was warped in the center which caused the case to buckle out, right above the lid latch. I called Apple Care and they offered a full refund or an exchange. I opted for the exchange. After the call, I decided I might be able to live with the Macbook Pro as-is with maybe a little "tweaking". After a few hours of use I realized it also suffered from the glitchy DVD drive issue - some would read, some wouldn't, some that would read were ssssssllllloooowwww. So another call to Apple Care and 20 minutes later I had a Fedex return label emailed to me. 2 hours after I printed the label from the Fedex website, I received another email that my replacement Macbook Pro was already shipped Priority Overnight to me! However inconvenient it may be that I have to send a unit back for defects, Apple more than made up for it by handling it the way they did.
And as far as Apple's strict refurbishment process goes, it is more than likely that the Macbook Pro arrived warped due to the shipping/packaging and not to lack of quality control. My Macbook Pro had no support underneath the center of it in the package. Which when subjected to say, a delivery person dropping it, would result in the area without support taking the brunt of the force. At least, that's my interpretation of it.
12 Powerbook G4 Mac OS X (10.2.x)
12 Powerbook G4 Mac OS X (10.2.x)
12 Powerbook G4 Mac OS X (10.2.x)

Post Your's 3DMark 2k1 scores HERE

I would like to verify my 3DMark 2001 SE (v.330). Post your's results with complete system description (drivers versions, ram timings, overclock settings (if any), ect.)
Here is my Baby:
- Athlon 3200 (2210 MHz - NC core, no OC)
- MSI K8N NEO Platinum (1.4 bios)
- 2x 512Mb PC3200 Kingston ValueRam (KVR400X64C2.5/512) at 2.5-3-8-3-1T (stock speeds)
- MSI 6800GT (stock speed)
- WD Caviar 80GB SATA 8Mb cache
- Tagan Tg-480 (480W)
- SB Audigy 2 ZS
- Other standar stuff
My 3D 2k1 score: 21435 (with above system&settings, all stock)
Run at:
- Win XP + SP2
- Dx: 9.0c
- ForceWare: 66.70
NOW YOUR'S RESULTS...

Here is mine using the system in my sig.........
3dmark01 score.....24,552
http://service.futuremark.com/compare?2k1=8165419
DX9c
66.81 nvidia drivers
XP Pro with SP2

Post Your's 3DMark 2001 scores HERE

I would like to verify my 3DMark 2001 SE (v.330). Post your's results with complete system description (drivers versions, ram timings, overclock settings (if any), ect.)
Here is my Baby:
- Athlon 3200 (2210 MHz - NC core, no OC)
- MSI K8N NEO Platinum (1.4 bios)
- 2x 512Mb PC3200 Kingston ValueRam (KVR400X64C2.5/512) at 2.5-3-8-3-1T (stock speeds)
- MSI 6800GT (stock speed)
- WD Caviar 80GB SATA 8Mb cache
- Tagan Tg-480 (480W)
- SB Audigy 2 ZS
- Other standar stuff
My 3D 2k1 score: 21435 (with above system&settings, all stock)
Run at:
- Win XP + SP2
- Dx: 9.0c
- ForceWare: 66.70
NOW YOUR'S RESULTS...

MSI K8N Neo Platinum (1.5b2 beta BIOS)
Athlon 64 3000+ @ 2.4GHz (10 x 240)
Radeon 9800 Pro @ 450/375
2x512MB Crucial PC3200 @ 240MHz @ 3-3-3-8 1T
Catalyst 4.9
Score: 23,077
URL: http://service.futuremark.com/compare?2k1=8134558

Oracle Config Tools DBCA DBUA NETCA NETMGR -Post your issues here

Hi
This thread is created to collect user experience with Oracle Config tools
DBCA DBUA NETCA NETMGR
You can post your questions,issues and if you come across any bugs you can post here .
This will be taken into consideration and the fix / solution will be given ASAP .
Looking forward for your responses .
Thanks
Kantha

Hi,
I have a Sun SPARC box . There are 7 instances 2 in 9.2.0.8 and 5 in 10.2.0.1 upgraded earlier than my joining. I want to upgrade one of the 9.2.0.8 databases.
The database to upgarde is up and running and can be connected through listener.
I login as the owner of ora10g and start dbua. It shows me all the 7 databases but when I select the database to upgrade it throws the following info :
[b]The Upgrade Assistant Failed in bringing up the database xxxx. Oracle Home /oracle/9.2.0.8 obtained from /etc/oratab was used to connect to the database. Either the database is not running from Oracle Home /oracle/9.2.0.8 or correct Initialization pfile was not found.
It then asks for pfile. -----------------------------------
The database is up and running.The Oracle home is also correct in Oratab file.
I checked the sqls.log file
It has info like
set heading off
set pagesize 0
set feedback off
set linesize 2048
set sqlprompt 'SQL_ENGINE_END_OF_SQL'
show sqlprompt
set sqlprompt 'SQL>'
set sqlprompt 'SQL>';
set heading off
set pagesize 0
set feedback off
set linesize 2048
set sqlprompt 'SQL_ENGINE_END_OF_SQL'
show sqlprompt
set sqlprompt 'SQL>'
connect /****** as SYSDBA
select count(*) from v$instance;
set heading off
set pagesize 0
set feedback off
set linesize 2048
set sqlprompt 'SQL_ENGINE_END_OF_SQL'
show sqlprompt
set sqlprompt 'SQL>'
Please help on this issue . Y cant the DBUA see that database is up?

Post your photo's here

post your photo's of your ipod with cases on or any other picture you like.

Why don't you?

Kt600 delta post your gripes here!

Major gripes with this board :-
1.why should i have to spend another £50 - £80 on a top of the range psu
just to run a £55 motherboard ?
The amount of people on this forum who have had to upgrade their psu just
to get this board up and running is unbelievable
2. heat :- this board runs a good 10 - 15 degrees higher than its nforce 2
counterparts ! so you have to go out and buy uprated cooling to
get a stable system
never mind trying to clock it
kt6 chipset :-this is the most unstable board i have ever fitted costing more in the long run to get it all up and running than any other ive built
shall stick to the nf2 in future
feel free to post your moans

1: The heat on the cpu, increased ALOT from my old KT400, very strange. It vas before, 39-40 (Idle) now its 45-46, much more I think, maybe there is something wrong with the sensor, or the KT400 had a 'good n' sweet days' sensor.
Well, that would be everything I think.
I ran my XP2500+ at 3200+ yesterday, and it was very stable, but I had to increase my TwinMOS PC2700 memory to 3v to have them in 400 mode. And even then I had to remove Ultra mode and everything else fast, that made the computer slower, atlest in 3dmark, then default clock on everything So I will just get better mem and then I will go 3200+ everyday, I hope, if there wont be a problem with the heat.
Using a open window, and a Cooler Master Aero 7 LITE at 45% speed, I suppose I can increase the speed if I want to clock but Its very loud then. I think, as I said that there might be some error with the sensor, cause the window was open, and the computer was just under it and totaly open, no plates or sidepanels or something, also it was -3C outside (sweden). The old motherboard (K4v) got much colder.
EDIT: I have a Q-TEC 550W (you say they suck, not mine ) and I still got very good voltage even when Im in so extreme overclock (to me that is extreme )

Mac Mini behaves poorly through DVI at 1920x1080 on HDTV displays

I recently purchased a Samsung LN-S4695D - a 46" LCD TV capable of 1080p with HDMI and VGA inputs. I've had been using my 23" Cinema Display + a Mac Mini G4 + Rotel Amp as the centerpieces of my Home Theater, and decided to change out the display to accommodate a gaming system and perhaps some other digital or component inputs (and, of course, nab a larger viewing surface). It seems like a fairly standard use of the Mini, but unfortunately many of us are running into disappointing results using our Minis as connected to an HDTV display. I'm writing here to see if we can clear up the issue with the mini and to attempt to identify reasonable workarounds or solutions until Apple gets the Mini right for HD home theater.
The current problem with the Mini and the Samsung TV/Display is that when the Mini is connected via DVI-HDMI (with a Monster 400 2m cable) to the display and asked to run at 1920x1080 (60hz NTSC) it does a reasonable job until it is required to refresh a lot of pixels (scrolling through album art in iTunes, playing DVD or other video, etc.). At that point, the screen fills with bands of static, and (if the rate of change is sustained) eventually looses the signal all together. With heavy scrolling operations, the signal returns as soon as scrolling stops, but with full-screen video it usually stays out until the mac resets its video resolution. Another article shows examples of this "DVI static" here:
http://www.freewebs.com/themagius/minidvipics.htm
So it is clear that the Mini and HDTVs don't play well at 1080 resolutions, as many of you have attested to. The samsung seems to do a better job than most with the Mini in that it it actually renders the 1080 as well as other resolutions, but flakes out on fast updates. While some other resolutions are also problematic, it is important to note that 1280x720 runs flawlessly on the Samsung, and is currently how I have mine set up (VGA input was too disappointing compared to DVI, though it scanned great and fit the image w/o over/underscanning.). Also, my Powerbook G4 1.25ghz (older than the mini) powers the Samsung perfectly at 1920x1080 as a secondary display, running DVD video or anything else that I throw at it, which leads me to believe that the mini is the problem. Here is another story very similar to mine that reports almost the same results with a Sharp LCD panel:
http://www.avsforum.com/avs-vb/showthread.php?p=5940932
So I've three sets of questions for Apple and the rest of you on this forum:
1) Why does the Mac Mini underpeform with the LCD display? The Powerbook works great, and the mini works great with my Cinema display (also 1920x1080) - where is the disconnect between the Mini and the Samsung? I understand very little about the actual details of DVI signals being carried across the wire, and don't understand what would cause the Powerbook to succeed, but the Mini to falter.
2) Assuming the Mini video hardware is at fault, has Apple improved this with the new Core 2 Duo line? Has anyone had success where previous Minis or other Apple hardware failed at 1080? If not, is there any announced intention to make the hardware that is positioned as being most ideal for the living room (ie, Mac Mini) actually DVI/HDMI-compatible with the finest HD living room devices?
3) An unfortunate sideffect of the DVI connection to the TV is that it requires the image from the Apple device to be oversanned (about a menu-bar's worth of pixels disappear on each edge) or underscanned (2" of black space around the image). Is there a common industry standard to correct this? Who is managing the overscan - the TV or the Mini? Also, can any utility, such as ScreenResX correct this until Apple manages to build in correction options into the OS for their living-room devices?
Thanks for all the help! Hopefully we can outline clear answers here in this thread for everyone else having similar problems.
Mac Mini G4 Mac OS X (10.4.8) Samsung LN-S4695D, Monster 400 DVI-HDMI 2m cable

David,
Great post. There's a lot to digest here. Let's get started!
The first question relating to noise, or static, over a TMDS (DVI) connection has to do with with the interoperability of various TMDS transmitters and receivers and how they are implemented. At this point in the market place there are thousands of combinations of transmitter/reciever pairings and obviously some are working better than others.
If you were to observe a TMDS signal with a scope there is something called the "eye" which is framed by the swing voltage and the bit time. When the eye collapses and is encroached upon, digital noise is the result. The noise margin is degraded by higher bit rates. That is why the mini and your TV are working at 720p but failing at 1080p...because the dot clock is that much higher for 1080p. The solution for cases such as this is to build a custom 1920x1080 timing that has reduced blanking, which allows for the lowering of the dot clock. Generally you can lower the dot clock sufficiently to get the noise to stop. LCD displays are relatively immune to reductions in blanking time so you can squeeze a lot out of a timing that was designed more with a CRT in mind.
To answer your second question, you can't fairly say the problem is with the mini. When you consider TMDS compatibility between two devices you have to take a whole system view. This includes not only the transmitter (mini) but the transmission line (PCB traces from the TMDS transmitter inside the mini to the mini's DVI connector -> the cable -> PCB traces from the DVI connector on the TV to the TMDS receiver in the TV), and the receiver. All three have to work together to make things come out right. You could probably just as easily find a display that works well with the mini that doesn't work with your PowerBook. It can be really had to pin the blame down to one device except in the most obvious cases where a certain device seems to be incompatible with just about everything. But I don't think the mini can be labeled that way. Compatibility is definitely an issue the industry still struggles with, especially at the higher clock rates approaching the 165MHz TMDS speed limit.
As for question 3, overscan is being forced by the TV, not by the mini. And, no, utilities like SwitchRes X and DisplayConfigX cannot be counted on to reliably deal with this except in the case of pure analog displays with magnetic deflection systems (e.g. old TVs and monitors). Once you have a digital processor involved and a matrix addressed display, tweaks to porch timings and blanking and such do not have predictable results. It seems to work in some cases but it is basically voodoo when it does. Purely luck.
If you want, I can help you to build a reduced blanking, 1080p timing that will most likely eliminate the DVI static. But you'll still be stuck with overscan. I should point out that a lot of manufacturers are starting to "get it" with respect to the public's desire to attach computers to their hi-def LCD televisions. I see a real shift in 2006 models. I believe the current crop of FHD (Full HD; native 1080) LCDs from the three "S" companies (Samsung, Sharp and Sony) all can display 1080p bit-for-bit now, meaning no overscan. So at least that is changing for the better. Write back if you want help with the timing.
Cheers. And thanks for starting this great thread.

T530 multiple display configuration

I have the T530 with the NVIDIA Optimus option that should allow a triple display configuration (two external displays and the laptop LCD).
I have been able to get a working configuration with the laptop LCD and two external displays over DisplayPort through the docking station.
I have found that upon some boot cycles, I am either stuck with just the laptop LCD as the only display or I am able to turn on only one external display. Sometimes a reboot will change it, sometimes it will not.
What's strange is that the NVIDIA control panel and the Windows display settings show all three LCDs, I am just not able to turn on one or both of the external displays (even if I turn off the laptop LCD).
Has anyone found a solution to this problem?
Thank you!
Solved!
Go to Solution.

Hi, admarsha
There are updates available for both your BIOS and Optimus that may help this issue. The BIOS update can be found here and the Optimus update can be found here. Looking over the ReadMe for the Nvidia update, part of the update does help with issues connected to multiple displays through docking stations so it may help.
Best,
Adam
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution!" This will help the rest of the community with similar issues identify the verified solution and benefit from it.

I need to change the display configuration of my macbook but I can't see to open the preferences (because the configuration is wrong!) - what can I do?

I need to change the display configuration of my macbook but I can't see to open the preferences (because the configuration is wrong!) - what can I do?

(cannot update previous post, exceeded timinout)
4. In case any of the previous operations work but the settings don't "stick". There are two plists associated with the settings:
/Library/Preferences/com.apple.windowserver.plist
~/Library/Preferences/ByHost/com.apple.windowserver.XXXXX-XXXXXXX.plist
The first is global to all accounts while the second is in your home directory. The X's are a sequence of hyphaninated letters and numbers. If you can get these removed then it will probably revert to a default resolution.

Steps to link a report to Web Application Form. Post Your Opinion

Hi friends,
After going through it what is your opinion. please do post your opinion.
Could any one give the complete steps of Linking a report to web form so that when called / clicked the link the report can display the data.
I have unchecked the "Report Option -> Save Data with Reports". So that the report could not take extra space.
I have DB connection code in my .aspx.vb file, it is as follows:
Private Sub ConfigureCrystalReports()
Dim fileName As String = "Reports\" & ReportID & ".rpt"
Dim reportPath As String = Server.MapPath(fileName)
myRepDoc = New ReportDocument()
myRepDoc.Load(reportPath)
myCrystalReportViewer.ReportSource = myRepDoc
myCrystalReportViewer.RefreshReport()
Dim myConnectionInfo As ConnectionInfo = New ConnectionInfo()
If Session("reportConnectionInfo") IsNot Nothing Then
Dim ConnInforArrList As ArrayList = DirectCast(Session("reportConnectionInfo"), ArrayList)
myConnectionInfo.ServerName = ConnInforArrList(0)
myConnectionInfo.DatabaseName = ConnInforArrList(1)
myConnectionInfo.UserID = ConnInforArrList(2)
myConnectionInfo.Password = ConnInforArrList(3)
Else
lblMessage.ForeColor = Drawing.Color.Red
lblMessage.Text = "Session is off. Please Relogin to See the Report."
End If
SetDBLogonForReport(myConnectionInfo, myRepDoc)
SetDBLogonForSubreports(myConnectionInfo, myRepDoc)
myCrystalReportViewer.SelectionFormula = GetFieldName(ReportID) & "='" & Session("CompCode") & "'"
myCrystalReportViewer.Visible = True
End Sub
Private Sub SetDBLogonForReport(ByVal myConnectionInfo As ConnectionInfo, ByVal myReportDocument As ReportDocument)
Dim myTables As Tables = myReportDocument.Database.Tables
For Each myTable As CrystalDecisions.CrystalReports.Engine.Table In myTables
Dim myTableLogonInfo As TableLogOnInfo = myTable.LogOnInfo
myTableLogonInfo.ConnectionInfo = myConnectionInfo
myTable.ApplyLogOnInfo(myTableLogonInfo)
Next
End Sub
Private Sub SetDBLogonForSubreports(ByVal myConnectionInfo As ConnectionInfo, ByVal myReportDocument As ReportDocument)
Dim mySections As Sections = myReportDocument.ReportDefinition.Sections
For Each mySection As Section In mySections
Dim myReportObjects As ReportObjects = mySection.ReportObjects
For Each myReportObject As ReportObject In myReportObjects
If myReportObject.Kind = ReportObjectKind.SubreportObject Then
Dim mySubreportObject As SubreportObject = CType(myReportObject, SubreportObject)
Dim subReportDocument As ReportDocument = mySubreportObject.OpenSubreport(mySubreportObject.SubreportName)
SetDBLogonForReport(myConnectionInfo, subReportDocument)
If myReportObject.Name = "Subreport1" Then
Dim lvSec As Section = subReportDocument.ReportDefinition.Sections("DetailSection1")
If Not lvSec Is Nothing Then
Dim t1 As TextObject
t1 = lvSec.ReportObjects("txtEmpName")
t1.Text = Session.Contents("EmpName")
Dim t2 As TextObject
t2 = lvSec.ReportObjects("txtRepID")
t2.Text = Request.QueryString("REPID")
End If
End If
End If
Next
Next
End Sub
Please do help me out as the data of report is not getting displayed on the report.
After going through it what is your opinion. please do post your opinion.
While creating the Report has the following Report Options on / checked.
1. Database Server is Case-Incensitive
2. Use Indexes Or Server For Speed
3. Verify on First Refresh
4. Show Preview Panel
5. Display Alerts on Refresh
6. Select Distinct Data for Browsing
Do I have check or uncheck any other option?
Thanks and regards
Edited by: Md. Mushtaque on Sep 6, 2008 2:50 PM
Edited by: Md. Mushtaque on Sep 8, 2008 9:27 AM
Edited by: Md. Mushtaque on Sep 8, 2008 12:14 PM

Sir AG,
Thanks a lot for replying and spending your valuable time for my problem.
Sir, I just want to put this in your knowledge that my application is web based application and I am calling these reports through web forms i.e. of ASP.NET coded in vb from .aspx.vb files.
So as per the code I have attached, I have this
Option Explicit On
Imports CrystalDecisions.CrystalReports.Engine
Imports CrystalDecisions.Shared
Next for ReportDocument Object:
Dim fileName As String = "Reports\" & ReportID & ".rpt"
        Dim reportPath As String = Server.MapPath(fileName)
        myRepDoc = New ReportDocument()
        myRepDoc.Load(reportPath)
        myCrystalReportViewer.ReportSource = myRepDoc
Above is the code used by me in Page_Init and I have already tested it from Page_Load. I have got few suggestions from this forum that I should put this code in Page_Init only.
Lastly:
The database connectivity code:
Dim myConnectionInfo As ConnectionInfo = New ConnectionInfo()
        If Session("reportConnectionInfo") IsNot Nothing Then
            Dim ConnInforArrList As ArrayList = DirectCast(Session("reportConnectionInfo"), ArrayList)
            myConnectionInfo.ServerName = ConnInforArrList(0)
            myConnectionInfo.DatabaseName = ConnInforArrList(1)
            myConnectionInfo.UserID = ConnInforArrList(2)
            myConnectionInfo.Password = ConnInforArrList(3)
        Else
            lblMessage.ForeColor = Drawing.Color.Red
            lblMessage.Text = "Session is off. Please Relogin to See the Report."
        End If
        SetDBLogonForReport(myConnectionInfo, myRepDoc)
        SetDBLogonForSubreports(myConnectionInfo, myRepDoc)
SetDBLogonForReport(myConnectionInfo, myRepDoc)
Private Sub SetDBLogonForReport(ByVal myConnectionInfo As ConnectionInfo, ByVal myReportDocument As ReportDocument)
        Dim myTables As Tables = myReportDocument.Database.Tables
        For Each myTable As CrystalDecisions.CrystalReports.Engine.Table In myTables
            Dim myTableLogonInfo As TableLogOnInfo = myTable.LogOnInfo
            myTableLogonInfo.ConnectionInfo = myConnectionInfo
            myTable.ApplyLogOnInfo(myTableLogonInfo)
        Next
    End Sub
This code I have got from a sample of the forum itself.
Sir, after all these effort and the unchecking of option "Save Data with Report" on calling the reports from my forms it is showing blank report. No data from the database is coming form the database.
I have uncheked the option "Save Data with Reports" to get the updated data each time the report has been called but now the status is that nothing is coming.
Thanks again for you precious and valuable effort to help me but the my problem is unsolved, So sir please if you could put an eye on it and help me out to get rid of this problem, I will be very thankful to you for your kind help.
Thanks and regards
Mushtaque

Best export settings? Post your tips!

I have been using iMovie for a long time. I have messed with settings quite a bit but the files always come out huge. I have seen other people's QT movies with great image quality for small file size. I have no idea how they do it.
My best experience in iMovie is to use the CD-ROM setting for export. This gives it the window size that I want, with a small file size, while maintaining pretty good image quality.
I'm talking about custom settings here. I need something other than the pre-made settings. There are so many custom options, but they're all way over my head. My goal is to use something other than h264, but keep the CD-ROM quality and size.
Does anyone have any good custom settings they recommend for getting a good balance of dimensions, image quality, and file size?
If so, post your tips! Let us know your favorite export settings!
--Timothy

The export settings are determined by the way the file is to be viewed.
"Local" files (those on CD's or fast networks) can be much larger in file size because bandwidth isn't much of an issue. Sent to iDVD and they make great videos that can only play in DVD players or software.
"Web" based files are a new can of worms because each persons opinion of "good" and also "small" file size differ so much.
Best advice anyone can give you is for you to make your own sample export "tests":
Take a minute sample (a part that has high action and motion) and choose the "Expert Settings" to send the file to QuickTime.
Try various video codecs and adjust the data and frame rate to raise or reduce file size.
Try AAC audio (very popular audio format) but set the frequency to "half" of CD quality (22050 Hz). This will be half as large in file size.
If your camera didn't record in stereo (most don't) set the file to mono and you reduce the file size in half again.
Compression is nearly an art form and the options in the expert settings can be a bit confusing.

Adobe Premiere Pro could not find any capable video play modules. Please update your video display drivers and start again.

I have administrator rights to the computer. The drivers are up to date. But I am still getting the error message "Adobe Premiere Pro could not find any capable video play modules. Please update your video display drivers and start again" when opening Premier Pro CS5.5. This appears to have happed after I upgraded to Mac OS 10.10.2.
Anyone?
Thanks

Hi Stan.
I had the same problem as you did though I am using Adobe CC. I saw nobody replied to you so perhaps my eventual success on my later version may have applications to the error on your version.
Anyhow, I did all the suggestions found here (Error "Premiere Pro could not find any capable video play modules" | Startup ) first and updated my NVidea card to no avail. Eventually what did the trick was this...
After mucking about with the video card, I said "OK lets just have a go at Premiere itself." So I uninstalled Premiere CC and reinstalled it. Now for some reason it didn't give me the latest patch but a slightly earlier version than the current one but lo and behold it was fine with the video card again. I was able to get my friend's video imported and quickly edited but then was having some issues with exporting where it would hang up but I went into Adobe Media Encoder and exported it there without a care. That task out of the way, I then went and made the update to the latest patch and it works perfectly fine - no video driver issues.
So short of it is this - if you've updated your drivers, perhaps what you could try uninstalling and reinstalling Premiere.
Let me know if this works.
Cheers and good luck

[Blog Post] Eclipse Scout 5 is here

We have posted a new blog post "Eclipse Scout 5 is here". Please use this forum thread to share your thoughts and pose any questions.

of course. the naming in the scout widget application might be misleading here.
regarding the naming of the outlines in the widgets application: pages and widget forms that are not (yet) refactored within the widget application are shown in an outline having "(old)" in its title. over time, these outline will get empty and disappear and the refactored content will become in other outlines.
explicitly: having pages or form fields in one of the outlines with a title "(old)" does not mean, that the form field/page is no longer supported with the Scout Neon release.

Post Your HDTV display CONFIGURATION HERE.

Similar Messages

Maybe you are looking for