Posting IDocs, partner profile setting

Hello,
I want to ask for advice.
It happens IDoc hangs on R/3 side while requesting data to load them to BW. This IDoc has no error and after manual processing (BD87) data are transfered correctly and IDoc posted. It is message type : RSRQST and it has set up " Trigger by background program" option in Partner profile / inbound parameters.
What could be the reason that IDocs hang without any error?
Addtionally:
what is recommended as IDoc processing  option?
is it : Trigger by background program or trigger immediatelly?
Thank you in advance, Peter

Thank you for fast feedback.
I checked notes 561880 , 555229 and 535172 but  they point to issues with resources during IDoc processing to application. I am not quite sure if this is my case. I Think my problem occured before the IDoc processing to appliccation.
I suppose if there is a problem with resources the IDoc gets  " status 64, "NO RESOURCES, IMMED. PROCESSING NOT POSSIBLE:
However the problem I am referring to is that IDoc gets  "Status 64, No filters , No conversion , No version change . If I understand it right this means that IDoc was processed by ALE and waits for further processing to Application. Unfortunately it doesn't start.
any idea what could be the problem? or does it really have something to do with resources?
Thank you,
Peter

Similar Messages

  • File -XI-Idoc partner profile error.

    Hi All,
    Iam trying to post a file to idoc scenario thru xi..when I post the idoc into the r3 system, it gives me an error saying partenr profile not available.
    I checked in the r3 system and have created a partner profile for my XI system and also added the idoc chrmas into inbound and outbound parameters in the dev and XI instance there..
    please could anyone guide me as to where else should i check for this error.. my idoc is in status 56.
    Thanks.

    Hello Shabrish,
    Thanks for your responce.. I went through all the mentioned steps..
    the issue was with the sender port. hence it was giving the exception and the status 56.. its been resolved..
    thanks again.

  • Help on idoc (partner profile)

    Hi All
    I am facing a weired problem , I am creating Idoc i R3 system and sending it to XI , every thing works fine men suddenly the status of the idon remains 32 by the RSEOUT00 program .
    Then I delet the partner profile and creat it again and thnigs turn out to be fine again.
    What can be the problem , I can not go on deleting the partner profile each time  specially in he production system.
    any help is apreciated.
    Thanks.

    Hi malu,
    Make sure there is no other session remains open for triggering the IDOC (with same user id) when you are triggering the IDOC from R3. This could lock the IDOC and hence the it will be get stucked.
    Regards,
    Sarvesh

  • IDOC Partner Profile

    Hi Experts,
                      What is the partner type we use in Partner profile for XI Linkage. I know we use LS for ALE Links.
    Thank you
    Kris

    Please check the following links which explains about the partner type Customer (KU) and Vendor (LI)
    http://www.*******************/2009/02/edi-idoc.html
    http://www.sap-img.com/sap-sd/partner-determination-for-sales-doc.htm
    http://www.sapdb.info/partner-determination-in-sap-sd/

  • IDOC Partner Profile for Sales Orders

    What kind of Partner Profile should i create to receive Sales Orders by IDOC from external non-SAP system by RFC?

    I created Partner Profile type KU (Customer) with name AAA001.
    AAA001 is customer, created in VD01.
    Added to inbound parameters:
    - Message type - ORDERS
    - Process code - ORDE
    - Trigger immediately
    Testing in WE19:
    E1EDK01-RECIPNT_NO = AAA001
    E1EDKA1-PARVW = AG, E1EDKA1-PARTN = AAA001
    Sales Order is not created.
    IDOC has following status:
    EDI: Partner profile not available                                                                               
    Message no. E0 332                                                                               
    Diagnosis                                                                               
    A partner profile could not be found with the following key:                                                                    
         /0000000000/  /                                                                               
    This involves the key fields of the table EDPP1:                                                                               
    -PARNUM  partner number                                      
         -PARTYP  partner type                                                                               
    Procedure                                                                               
    Please check the EDI partner profiles.
    Edited by: S S on Dec 21, 2008 4:51 PM

  • How workflow will be triggered from the Idoc partner profiles

    Hi,
         We have scenario like, We are doing business with the same vendor in different countries. When ever we receive the Idoc from that vendor, Agent will be notified based on the agent details, which is mentioned in the Inbound partner profiles for that vendor. Now they like to enhance the scenario like different agents should be notified for different countries, based on the company code from the same vendor. I came to know that its possible through workflow, can you please let me know the step by step procedure to achieve this scenario. Since this is very important issue, need your help as soon as possible.
    Thanks
    Satyasuresh

    Hi,
    In Tx. WE42, Select the process code for the corresponding partner and bind your workflow / task inplace of the function module with the process code. Now, this will enable the idoc to get placed in the agents(identified by that workflow)inbox.
    But to design the workflow, you`ll have to use tx. swdd and prior to that get some basic understanding of Business Workflow from SAP Library.
    Hope the info. is helpful and reward points if so.
    Regards

  • Partner profile setting between BI and R3

    Dear all,
    we have client refersh of R3 quality now they have change the name of the client to 330 to 720.
    now if i chekc the source systm , it show the RFC checked failed.
    now i need to connect with new configuration so please let me know what are the step and what should i do in partner profile with details.i have only one day to do this.

    Hi Viral,
    Check this link :
    https://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/908836c3-7f97-2b10-4cb8-e6790361c152
    Cheers,
    Tanish

  • Partner profile set-up

    Hi All,
    How we can assign a different vendor as a Good Supplier for a particular vendor. I have checked in main vendor master partner profile not able to find the same.
    Thanks
    Chandru

    Hi CHANDRAMOHAN ,
    Please go through the above link :
    Partner Function in Vendor master

  • Partner profile settings - Trigger Immediate or Collect Idocs ??

    Hi All,
    We have EDI Setup between SAP and a EDI system and Idocs flowing with port type TCP/IP connection.
    we are facing issue at some times where in the Idoc is created and is in status 03 / 12 (trfc queue is cleared) but not found in the EDI system.
    what I have observed is the issue has occurred for only few vendors where partner profile setting in trigger immediately
    and it has not occurred t for every Idoc created, only some Idocs were missing in EDI system.
    issue was not present in case  where partner profile setting in collect Idocs.
    So it that do we have a best practice to set partner profile to collect Idocs (packet size ~ 20) when sending to EDI subsystem?

    Hi,
    It seems the issue is not because of your partner profile setting since your status of the IDOC is 03 0r 12.
    Output mode 'Transfer Idoc Immediate': Single Idoc is transfered immediately to the EDI system when the output triggered
    'Collect Idoc': Idocs generated for the particular message type will be collected in a single file and are triggered to  EDI system at a scheduled time. Here no of Idocs sent in a file will be decied based on packet size.
    It may be problem with your network connectivity.If are using a EDI substem then you use file port not trfc port.
    Check how the EDI sytem is reading the Idoc files which are created in R/3 OS level is it through FTP???
    Regards
    Praveen

  • No partner profiles (message control) maintained.

    Hi Friends,
    I have created a PO but getting error message in output type that
    No partner profiles (message control) maintained.
    Message no. B1127
    Diagnosis
    No IDOC partner profiles have been created for the message control for for application EF, condition key ZDPO and change message '' with partner type 'LS' and partner role '  '.
    Procedure
    Please create the partner profiles for the logical system that should contain the IDOC. You can either generate them from the ALE model or create them manually.
    Any pointers.
    Regards

    Hi,
    I get the same Error message can someone help?
    No partner profiles (message control) maintained
    Message no. B1127
    Diagnosis
    No IDOC partner profiles have been created for the message control for for application EF, condition key ZZVA and change message '' with partner type 'LS' and partner role '  '.
    Procedure
    Please create the partner profiles for the logical system that should contain the IDOC. You can either generate them from the ALE model or create them manually.
    I  need to send my PO information to a Logical system.
    1) Created new message type ZZBA. Message type triggers automatically but fails.
    2) I did create a LS Partner profile (PART123) in WE20
    3) In outbound parameters, in partner profile I entered
    LS/ORDERS
    4) Basic type- ORDERS01
    5) In message control i have
    EF/ZZBA/ME10
    6) Maintained condition record for ZZBA
                     PO type/ LS/PART123/A/4/EN
    please help
    Regards
    Raj

  • Is it possible to transport partner profile settings ?

    hello,
    is it possible that whatever partner profile settings i have maintained in development server that i can transport into production server?
    or i have to maintain it manually?

    Hi,
    Partner profile setting are actually soft configuration and you cannot transport them.
    You have to set partner profile in all stages.
    Nilesh

  • Error while posting Inbound Idocs-"EDI: Partner profile not available"

    Hi,
    I am getting the error "EDI: Partner profile not available" Status -56 while creating inboud Idocs.
    I have done the following steps so far
    1.Created IDOC basic Type and Message Type. (Custom)
    2. Created process code to process the IDOC.
    3. Use the FM IDOC_INBOUND_WRITE_TO_DB to create the inbound IDOC.
    4. Use the FM IDOC_START_INBOUND to process the IDOC.
        Is ther anything else that i have to do inorder to post the idoc sucessfully.
    Thanks in advance
    -Nishant
    Edited by: nishant patel on Nov 13, 2009 10:35 AM
    Edited by: nishant patel on Nov 13, 2009 10:41 AM

    Hi,
    Check in WE20 if the partner profile is configured for the idoc type and the message type. That might be the cause of the error.
    Also make sure the same partner profile details are sent to the control record. Partner profile details are stored in the table EDP13.
    Hope this helps
    Regards
    Shiva

  • IDOC status 30 but partner profile is set to send immediately (04)

    Hi guys,
    I have a problem with idocs not being sent immediately... The outputs, the EDI partner profiles are all set up correctly...
    it is configured to send immediately however, it's not doing so... prior to upgrade to ECC 6.0 it's working fine... now its not...
    However, in BD87 thru manual release of IDocs, it is working fine...
    Is there any changes to ECC 6.0 for this matter? or is there anything that needs to be set up other than those mentioned above in order for it to work in ECC 6.0?
    Thanks a lot!

    Mark, have you looked at the OSS notes? By 'IDOC status 30' it finds 300+ notes, this is really a wide-spread issue.
    The most recent one is 150202, which actually recommends collecting the IDocs instead of having "send immediately" because it saves the RFC resources. This is not really an ABAP issue, so you might want to discuss this with your Basis admin.
    Also, from my experience, even with "mission critical" processes the users, in fact, never feel any real difference between "immediate" and 5-10 min. Sometimes (due to a technical problem, for example) nothing goes on for 30+ min. and no one even notices.

  • Error when posting  Idocs From XI to SAP by Partner Profile

    Hi all.
    i have a problem. all my inbound IDocs in R3 use PP(Partner Profile) LS_XID.
    but i need to send IDoc MATMAS by a diferent PP (LS_MATERIALS).
    So, i added a new BS in transaction BD54.
    In transaction BD64 re-desing the Distribution Model as follow
    SL_130 (R3 DES)
    > LS_MATERIALS (XI)
                |> MATMAS.
    In transaction WE20 define the new PP LS_MATERIAL. In inbound table add the MATMAS IDoc. Later imust delete de MATMAS IDoc from LS_XID list. same as transaction BD64.
    My problem is when send the MATMAS to R3. it is still using PP SL_XID, so IDoc get status 56 (EDI: Partner Profile Inbound not Available) in R3.
    Why?? Any IDea??
    Thanks & Regards
    Rodrigo.

    Hi,
    Please check the Logical system,Business system, configurations ,please see the below links
    https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/cdded790-0201-0010-6db8-beb9bb2b2660
    /people/prateek.shah/blog/2005/06/08/introduction-to-idoc-xi-file-scenario-and-complete-walk-through-for-starters
    /people/anish.abraham2/blog/2005/12/22/file-to-multiple-idocs-xslt-mapping
    /people/ravikumar.allampallam/blog/2005/06/24/convert-any-flat-file-to-any-idoc-java-mapping
    Regards
    Chilla..

  • Using SYPART01 IDOC for setting partner profiles from external system

    We wish to maintain our partner profiles from an external system.
    Is there any existing interface for doing this.
    It seems that the sypart message is only for output, not input.
    Any ideas or suggestions?
    Thanks!
    Dan

    Hello Dan,
    Thanks for your post.
    I hope the following code helps in future.
    http://wiki.sdn.sap.com/wiki/display/Snippets/Copy+partner+profiles+with+SYPART+message+quickly.

Maybe you are looking for