POTS/Analog Dial Access with PVDM3 and 3900? Possible?

I have a PVDM3-16, 3925 and HWIC-CE1T1-PRI.
I have a T1 terminating in the HWIC and the other end goes to an ATLAS 800. I dial into it with an analog v.92 modem. It provides dial-tone and a phone numbering setup. Sort of a self-contained phone system in-a-box.
My old, existing, setup is an AS5200 hanging off of that same ATLAS, on another T1 port.
All I want to do is dial in and establish a PPP session. Simple on the AS5200. Not so much with the PVDM3.
I have seen all sorts of documentation about doing this with a PVDM2, but not with a PVDM3. I assume the "3" would have all of the features of the "2" with newer ones to boot.
My main problem is figuring out how to refer to the 16 "modems" in my router. The PVDM2 docs note the line numbers created when it is installed in X800 series routers, but I have found no such documentation for the PVDM3. Also, I am having some conceptual difficulty getting my mind around modems that don't have hardware support. In the AS5200's modem cards, I can deal with actual "line" commands, however, I assume that the digital modems in the PVDM3 don't generate that. Is that correct?
If anyone is using PVDM3 modems to support POTS/Analog dial-in via a channelized T1 or PRI, I would greatly appreciate any direction you can provide.
I'm not asking for someone to essentially configure it for me. I'd be happy knowing how to setup the PVDM3 to act like run of the mill analog modems and maybe some insight into how that translates into async line references.
Thanks,
Andy

Paolo,
Thank you for your reply.
I can't actually find any documentation that differentiates between a PVDM2 and a PVDM2-XXDM. As far as I can see, the "XX" is the number of modems contained on the card. Like PVDM2-12DM, where "12" replaces the generic "XX". Is this not the case? Are "PVDM2"s and "PVDM2-12DM"s, for example, two different SKUs?
I had heard, but have not yet found supporting info online, that the PVDM2s have been announced as EOS.
I have seen the PVDM EOS/EOL announcement onnline.

Similar Messages

Remote Desktop Access with Mac and Asus Transformer Prime

I have an E2000 router with the most current firmware. I have a Sony VAio laptop with Windows 7 Home Premium 64bit,a Macbook with 10.6.8, and a new Asus Transformer Prime with ICS.My work desktop is a Dell Optiplex 380 with Windows 7 Pro 32bit. I frequently work from home and have no issues remoting into to my work PC from by Sony laptop via VPN and RDP.However I have never been able to connect successfully to my work PC with my Macbook(using Remote Desktop Connection 2.1 for Mac OS) or Asus tablet(using WYSE Pocket Cloud RDP app for Android). I can however connect to the VPN itself on the Macbook and tablet without issue same as my Windows laptop. The other interesting part is I can connect via RDP when I am connected to a Mi-Fi 3g hotspot. So it is definitely something in the my Linksys E2000 blocking the connection for some reason. I have even set Port forwarding of 3389 with the ip's of both the Macbook and Asus tablet.I have also tried connecting via ethernet to the router with the same outcome. I cannot ping my work pc from either device as well.In addition the firewall on my work PC is completely disabled and all services related to Remote desktop access are enabled and running.Does anyone have any ideas?

For my tablet its own ip assigned by the router. Same with the macbook.the Pocketcloud RDP app also uses 3389.I have port 3389 set for both internal and external port and protocol "both" under the Single Port Forwarding tab in the router config.

LWA Guest Access with ISE and WLC

Hi guys,
Our Company try to implement Guest Access with ISE dan WLC with Local Web Auth Method. But there is problem that comes up with the certificate. This is the scenario :
1. Guests try to connect wifi with SSID Guest
2. Once it connect, guests open the browser and try to open a webpage (example: cisco.com)
3. Because, guests didn't login, so it redirect to "ISE Guest Login Page" (url became :
https://ise-hostname:8443/guestportal/Login.action?switch_url=https://1.1.1.1/login.html&wlan=Guest&redirect=www.cisco.com/
4. If there is no ISE Guest Login Page installed, message Untrusted Connection message will appear, but it will be fine if they "Add Exception and install the certificate"
5. After that the Guest Login Page will appear, and guests input their username and password.
6. Login success and they will be redirected to www.cisco.com and there is pop up from 1.1.1.1 (WLC Virtual Interface IP) with logout button.
The problem happen in scenario 6, after login success, the webpage with ISE IP address and message certificate error for 1.1.1.1 is appear.
I know it happened when guests didn't have the WLC Login Page Certificate...
My Question is, is there a way to tunneling WLC Certificate on ISE ? Or what can we do to make ISE validate WLC Certificate, so guests doesn't need to install WLC Certificate/ Root Certificate before connect to Wifi ?
Thx 4 your answer and sorry for my bad English....

Thx for your reply Peter, your solution is right,
i don't choose CWA, because their DNS is not stable...
i've found the problem...
the third-party CA is revoked, so there is no way it will success until it fixed...
and there is no guarantee, they will fix it soon..
so solution that we choose is by disable "HTTPS" on WLC...
"config network web-auth secureweb disable".
"config network web-auth secureweb disable".
"config network web-auth secureweb disable".
"config network web-auth secureweb disable".
"config network web-auth secureweb disable"
thank you all...

Migrating Non ASM, Non RMAN to New Server with ASM and RMAN - Possible?

We currently have a database ( Oracle 10g R1 ) on a Sun Solaris server that is NOT using ASM or RMAN. The database is about 300GB. We are getting a new server and we want to install Oracle 10g R2 with ASM and RMAN and migrate the database.
I have seen the documentation on migrating non ASM to an ASM server but the methods all use RMAN. Is it possible to migrate to an ASM database without using RMAN? Would datapump import/export work if I created a new database on the new server with all the same tablespaces? Or, do I have to bite the bullet, install RMAN on the old server and do the backup?
Thanks.

If you're not using RMAN that doesn't mean you can't use it to perform a single backup, rman is contained in every oracle RDBMS installation version 10G or higher.
this is only a sample of how to do it
RMAN> CONFIGURE CHANNEL DEVICE TYPE DISK FORMAT '<file_system_path>/%U.DBF';
--first we allocate the channel default channel.
RMAN>RUN
ALLOCATE CHANNEL DEFAULTCHANNEL TYPE DISK;
SHUTDOWN IMMEDIATE;
STARTUP MOUNT;
BACKUP DATABASE;
SHUTDOWN
}then once you have it, you can do what you want.
It should also be possible to manually restore the database from the original datafiles but it's better to follow the solution involving RMAN.
Bye Alessandro

FAX and Dial-access with 5350

I have a 5350 router, and I get some troubles. I can't use fax over wan links. Before I had a 5300 router and it works fine (same IOS version). Voice works fine, but I can't use fax. This interface is E1 with ISDN Q-Sig.
Configuration below...
==
version 12.2
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname 5350
no boot startup-test
logging buffered 20480 debugging
aaa new-model
aaa authentication login default local
aaa authentication enable default enable
aaa session-id common
resource-pool disable
calltracker enable
spe default-firmware spe-firmware-1
ip subnet-zero
ip cef
frame-relay switching
isdn switch-type primary-qsig
isdn voice-call-failure 0
voice call send-alert
voice call carrier capacity active
voice rtp send-recv
voice service voip
fax protocol t38 ls-redundancy 0 hs-redundancy 0
mta receive maximum-recipients 0
controller E1 3/0
pri-group timeslots 1-31
interface FastEthernet0/0
ip address x.x.x.x x.x.x.x
duplex auto
speed auto
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface Serial3/0:15
no ip address
isdn switch-type primary-qsig
isdn overlap-receiving
isdn incoming-voice modem
isdn bchan-number-order ascending
isdn sending-complete
no cdp enable
interface Group-Async0
ip unnumbered FastEthernet0/0
encapsulation ppp
ip tcp header-compression
async mode dedicated
peer default ip address pool mypool
ppp authentication pap
group-range 1/00 1/59
ip local pool mypool x.x.x.x x.x.x.x
ip classless
ip route 0.0.0.0 0.0.0.0 x.x.x.x
no ip http server
call rsvp-sync
voice-port 3/0:D
bearer-cap Speech
voice-port 3/1:0
compand-type a-law
mgcp profile default
dial-peer cor custom
dial-peer voice 8400 pots
application data_dialpeer
incoming called-number 8400
port 3/1:0
forward-digits all
dial-peer voice 1000 pots
destination-pattern 1...
direct-inward-dial
port 3/0:D
forward-digits all
dial-peer voice 1001 pots
destination-pattern 8...
direct-inward-dial
port 3/0:D
forward-digits all
dial-peer voice 2000 voip
destination-pattern 12..
session target ipv4:x.x.x.x
dtmf-relay rtp-nte
ip qos dscp cs5 media
5350#sh ver
Cisco Internetwork Operating System Software
IOS (tm) 5350 Software (C5350-IS-M), Version 12.2(11)T8, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Thu 27-Mar-03 22:32 by hqluong
Image text-base: 0x60008948, data-base: 0x61380000
ROM: System Bootstrap, Version 12.2(1r)1, RELEASE SOFTWARE (fc1)
BOOTLDR: 5350 Software (C5350-BOOT-M), Experimental Version 12.1(20000922:142008) [nag-flo_t_0110 101]
cfw-5350-voip uptime is 1 day, 3 hours, 8 minutes
System returned to ROM by reload at 00:23:01 brz Fri Jan 21 2000
System image file is "flash:c5350-is-mz.122-11.T8.bin"
cisco AS5350 (R7K) processor (revision T) with 131072K/65536K bytes of memory.
Processor board ID JAE070401D5
R7000 CPU at 250Mhz, Implementation 39, Rev 1.0, 256KB L2, 2048KB L3 Cache
Last reset from IOS reload
Channelized E1, Version 1.0.
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
Primary Rate ISDN software, Version 1.1.
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x32,
Board Hardware Version 3.34, Item Number 800-5171-02,
Board Revision C0, Serial Number JAE070401D5,
PLD/ISP Version 2.2, Manufacture Date 24-Jan-2003.
Processor 0x14, MAC Address 0x0B5FDAB22
Backplane HW Revision 1.0, Flash Type 5V
2 FastEthernet/IEEE 802.3 interface(s)
37 Serial network interface(s)
60 terminal line(s)
2 Channelized E1/PRI port(s)
512K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)
8192K bytes of processor board Boot flash (Read/Write)
Configuration register is 0x2102
5350#
===
Can someone help me?
regards

try this:
voice service pots
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711alaw
voice service voip
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711alaw
dial-peer voice 900 voip
permission term
description your outgoing dialpeer
destination-pattern ^1234..
modem relay nse codec g711alaw redundancy
modem relay latency 150
modem relay sprt retries 6
fax-relay ecm disable
fax nsf 000000
fax protocol t38 ls-redundancy 2 hs-redundancy 2 fallback pass-through g711ulaw
no vad
and make sure you have g711alaw and g711ulaw in your codec preference list.

Remote desktop access with VNC and KDE

Hi,
I want to access from my win machine the arch linux one with remote desktop the KDE graphic interface.
I've installed xrdp and I can connect in the session :1 but not on the session :0 (the one one that allow you to control the real desktop)
I do not think with xrdp I connet to the session :0, do you know how can I do it?
thanks

thanks for your answer,
my need is very easy, I have my linux box in the living room and it is connected to the TV through HDMI.
I want to control it from my laptop, (that is on my knees) what I see on the tv without need to go till there (i'm lazy and the sofa is very confortable), mainly I want to play/stop movies and browse internet for add torrents to ktorrent.
And I would like to remove the keyboard and the mouse from the linux box (but this is not a must)
if there is a better way to do that, please tell me
thanks

Wireless guest access with CWA and ISE using mobility anchor

My team is trying to demo wireless guest access using CWA with an ISE server. We appear to be hitting an issue when combining this with mobility anchoring.
When we don't use a mobility anchor the authentication goes off without a hitch seemingly proving that the ISE configuration is sound. The test laptop associates and gets redirected, auths, moves to the RUN state and access to the network is granted.
When the mobility anchor is enabled, the test laptop does get redirected, authentication is successful, but the process does not fully complete, as on the foreign controller the user is in RUN state whereas on the anchor the user is still stuck at CWA required.
Now, I've read the L2 auth occurs between the foreign controller and ISE, and the L3 auth occurs between the anchor controller and ISE, but this does not appear to borne out in packet captures of the process where both parts of the auth seems to go to and from the foreign controller and ISE.
I'm curious to know if anyone else has come across this issue, or has ideas where I should be looking in the config or debugs to find the root cause.
When setting up the controllers and ISE this guide (linked below) was used and the controllers are 2504 controllers on 7.5 series software and ISE is on the latest 1.2 patches:
http://www.cisco.com/en/US/products/ps11640/products_configuration_example09186a0080bead09.shtml
To me it seems to be mobility related, but the authentication flow does seem to be off compared with what the guide says.

FOREIGN
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Adding mobile on LWAPP AP 0c:d9:96:ba:7d:20(1)
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Association received from mobile on BSSID 0c:d9:96:ba:7d:2f
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Global 200 Clients are allowed to AP radio
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Max Client Trap Threshold: 0 cur: 0
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 0 Quarantine Vlan 0 Access Vlan 0
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Re-applying interface policy for client
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2164)
*apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2185)
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 In processSsidIE:4565 setting Central switched to TRUE
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 In processSsidIE:4568 apVapId = 1 and Split Acl Id = 65535
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Applying site-specific Local Bridging override for station 00:1e:c2:c0:96:05 - vapId 1, site 'AP-Group-CHEC.default', interface 'management'
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Applying Local Bridging Interface Policy for station 00:1e:c2:c0:96:05 - vlan 84, interface id 0, interface 'management'
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 STA - rates (8): 140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfProcessAssocReq (apf_80211.c:7830) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Idle to AAA Pending
*apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station: (callerId: 20) in 10 seconds
*radiusTransportThread: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Username entry (00-1E-C2-C0-96-05) created for mobile, length = 253
*radiusTransportThread: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Username entry (00-1E-C2-C0-96-05) created in mscb for mobile, length = 253
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Received SGT for this Client.
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Redirect URL received for client from RADIUS. Client will be moved to WebAuth_Reqd state to facilitate redirection. Skip web-auth Flag = 0
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Resetting web IPv4 acl from 255 to 255
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Resetting web IPv4 Flex acl from 65535 to 65535
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 84
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Re-applying interface policy for client
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2164)
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2185)
*apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 0 on mobile
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Inserting AAA Override struct for mobile
MAC: 00:1e:c2:c0:96:05, source 2
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Initializing policy
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 AUTHCHECK (2) Change state to L2AUTHCOMPLETE (4) last state AUTHCHECK (2)
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Not Using WMM Compliance code qosCap 00
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 0c:d9:96:ba:7d:20 vapId 1 apVapId 1 flex-acl-name:
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state L2AUTHCOMPLETE (4)
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfMsAssoStateInc
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from AAA Pending to Associated
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfPemAddUser2:session timeout forstation 00:1e:c2:c0:96:05 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is 0
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Sending Assoc Response to station on BSSID 0c:d9:96:ba:7d:2f (status 0) ApVapId 1 Slot 1
*apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfProcessRadiusAssocResp (apf_80211.c:3066) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Associated to Associated
*DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
*DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
*DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0, mobility state = 'apfMsMmQueryRequested'
*DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
*DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
*DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0, mobility state = 'apfMsMmQueryRequested'
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=ExpForeign, client state=APF_MS_STATE_ASSOCIATED
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 apfMsRunStateInc
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 DHCP_REQD (7) Change state to RUN (20) last state DHCP_REQD (7)
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Reached PLUMBFASTPATH: from line 5793
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Adding Fast Path rule
type = Airespace AP Client
on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
IPv4 ACL ID = 255, IPv6 ACL ID = 255,
*mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206 Local Bridging Vlan = 84, Local Bridging intf id = 0
*mmMaListen: Jan 28 23:05:02.363: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
*pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 0.0.0.0 Added NPU entry of type 1, dtlFlags 0x4
*pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 Skip Foreign / Export Foreign Client IP 0.0.0.0 plumbing in FP SCB
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP processing DHCP REQUEST (3)
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 0
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   xid: 0xafea6bc9 (2951375817), secs: 5, flags: 0
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   chaddr: 00:1e:c2:c0:96:05
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   ciaddr: 0.0.0.0, yiaddr: 0.0.0.0
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   siaddr: 0.0.0.0, giaddr: 0.0.0.0
*DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   requested ip: 10.130.98.8
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP received op BOOTREPLY (2) (len 320,vlan 84, port 13, encap 0xec07)
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP processing DHCP ACK (5)
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   xid: 0xafea6bc9 (2951375817), secs: 0, flags: 0
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   chaddr: 00:1e:c2:c0:96:05
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   ciaddr: 0.0.0.0, yiaddr: 10.130.98.8
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   siaddr: 10.30.4.173, giaddr: 0.0.0.0
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   server id: 1.1.1.2 rcvd server id: 1.1.1.2
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) DHCP Address Re-established
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Reached PLUMBFASTPATH: from line 6978
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Replacing Fast Path rule
type = Airespace AP Client
on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
IPv4 ACL ID = 255, IPv6 ACL ID
*DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206 Local Bridging Vlan = 84, Local Bridging intf id = 0
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 Assigning Address 10.130.98.8 to mobile
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP success event for client. Clearing dhcp failure count for interface management.
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP success event for client. Clearing dhcp failure count for interface management.
*DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP successfully bridged packet to STA
*pemReceiveTask: Jan 28 23:05:03.889: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
*pemReceiveTask: Jan 28 23:05:03.889: 00:1e:c2:c0:96:05 10.130.98.8 Added NPU entry of type 1, dtlFlags 0x4
*pemReceiveTask: Jan 28 23:05:03.890: 00:1e:c2:c0:96:05 Skip Foreign / Export Foreign Client IP 10.130.98.8 plumbing in FP SCB
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Received SGT for this Client.
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Resetting web IPv4 acl from 0 to 255
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Resetting web IPv4 Flex acl from 65535 to 65535
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 AAA redirect is NULL. Skipping Web-auth for Radius NAC enabled WLAN.
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Inserting AAA Override struct for mobile
MAC: 00:1e:c2:c0:96:05, source 2
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Setting session timeout 3600 on mobile 00:1e:c2:c0:96:05
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Session Timeout is 3600 - starting session timer for the mobile
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Applying cached RADIUS Override values for mobile 00:1e:c2:c0:96:05 (caller pem_api.c:2307)
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Setting session timeout 3600 on mobile 00:1e:c2:c0:96:05
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Session Timeout is 3600 - starting session timer for the mobile
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Applied RADIUS override policy
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Replacing Fast Path rule
type = Airespace AP Client
on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
IPv4 ACL ID = 255, IPv6 ACL ID
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206 Local Bridging Vlan = 84, Local Bridging intf id = 0
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Not Using WMM Compliance code qosCap 00
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Plumbed mobile LWAPP rule on AP 0c:d9:96:ba:7d:20 vapId 1 apVapId 1 flex-acl-name:
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Change state to RUN (20) last state RUN (20)
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfMsAssoStateInc
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from AAA Pending to Associated
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfPemAddUser2:session timeout forstation 00:1e:c2:c0:96:05 - Session Tout 3600, apfMsTimeOut '1800' and sessionTimerRunning flag is 1
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station: (callerId: 49) in 3600 seconds
*apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 3600
*apfReceiveTask: Jan 28 23:05:18.718: 00:1e:c2:c0:96:05 Sending Assoc Response to station on BSSID 0c:d9:96:ba:7d:2f (status 0) ApVapId 1 Slot 1
*apfReceiveTask: Jan 28 23:05:18.718: 00:1e:c2:c0:96:05 apfProcessRadiusAssocResp (apf_80211.c:3066) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Associated to Associated
*pemReceiveTask: Jan 28 23:05:18.720: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
*pemReceiveTask: Jan 28 23:05:18.720: 00:1e:c2:c0:96:05 10.130.98.8 Added NPU entry of type 1, dtlFlags 0x4

ARD Access with enabled Firewall not possible under Leopard

I got a network and my clients are running mostly Mac OS X 10.5.8 Leopard. When the Firewall is on i am not able to connect with Apple Remote Desktop even though the Firewall automatically enables the ARD service. Does anyone know what to do? My 10.4.11 Tiger clients do not have the same issue.

Try the ARD forum under Server Products.

ARD Access with enabled Firewall not possible

I got a network and my clients are running mostly Mac OS X 10.5.8 Leopard. When the Firewall is on i am not able to connect with Apple Remote Desktop even though the Firewall automatically enables the ARD service. Does anyone know what to do? My 10.4.11 Tiger clients do not have the same issue.

Try the ARD forum under Server Products.

Dual screen with MacBook and iBook possible?

Hi,
I was wondering if it was possible to have the MacBook and a iBook G4 hooked up dual screen?
If so what are the things I need to make it happen?
I am doing photo editing and just got a MacBook and I need the extra screen space and I have my old iBook laying around my house and thought I could use it for extra screen space.
Thanks for the help,
Sam

Unfortunately you can't, and there really isn't anyway to do it. You would be best of buying a cheap LCD monitor.
-Internet Wiz™

Video broadcast with bridge and pvdm3

Hey all,
Any way to do a Video broadcast with a 4520 bridge and a 2911 with pvdm3..
We want the bridge to dial out to all locations. If the 9971 video phones dial in to a 2911 conf using pvdm3's is there a way to get the bridge to dial out to that conf?
Sent from Cisco Technical Support iPad App

I'm hoping that I am missing something because this seems like a strange request. Are you saying that you want a 4520 MCU to outdial to a preset group of endpoints when a completely separate PVDM3-based ad-hoc conference is started? The answer to this would be no.
What may be possible would be to join the H323 ID/E164 ID of the 4520 conference to the PVDM3-based ad-hoc conference by calling it and using the Join button on the Cisco phone. If that worked, the obvious downside would be that you have a cascaded conference across two MCUs. Each MCU would make its own active speaker decisions and feed only that output to the other bridge.

Im not satasfied with 6.0 i miss youtube and some apps are slower, facebook wants premission to access my contacts, and how do i use apple tv feature with out mirroring?

Im not satasfied with 6.0, i miss youtube, some apps are slower, facebook wants premission to access my contacts, and how do i use apple tv feature with out mirroring?

That is awesome, works perfectly.
I'll get it worked into my main script. Is this Action Manager code, and not just regular Javascript from the Scripting Dictionary? I can't tell the difference. I'll see whether or not it's actually faster than Applescript.
Thanks. I know Scripting Listener records a bunch of stuff, but it's pretty amazing to me that playing back this line does the same thing that playing back the 1,011 lines Scripting Listener puts out.
Thanks.

HT6114 My Mac Book Pro had a split drive with Windows Microsoft Access on it and it was removed when Mavericks installed. I need this so how can I go back to the old system?

My Mac Book Pro had a split drive with Windows Microsoft Access on it and it was removed when Mavericks installed. I need this so how can I go back to the old system?

Restore from the backup you had prior to installing Mavericks.
However, the upgrade should not have altered your partition scheme. Did your erase and format the drive prior to upgrading?

When accessing eBay with Firefox and launching a search, I get less results/hits with Firefox then when using Internet Explorer, why? Try it, you'll see.

For example access eBay with Firefox and launch a search on the word Frankenstein: you'll get something like 23,671 results (if you search in ''All categories''). Then quit the Firefox browser and load Microsoft Internet Explorer instead; access eBay again and repeat the very same search: this time you'll get 25,383 results. These are reral figures that I tried at 19:21 on March 20, 2014. Why does a search on eBay through Firefox report less hits than the very same search through Internet Explorer? Using Firefox rather than Microsoft Internet Explorer automatically means missing hits/results/items on eBay: that doesn't make sense but it does happen. Why is it so? Thank you, somebody, for shedding light on this problem.

Try this steps and try to load the same once again!!!
Hello,
Many site issues can be caused by corrupt cookies or cache. In order to try to fix these problems, the first step is to clear both cookies and the cache.
Note: ''This will temporarily log you out of all sites you're logged in to.''
To clear cache and cookies do the following:
#Go to Firefox > History > Clear recent history or (if no Firefox button is shown) go to Tools > Clear recent history.
#Under "Time range to clear", select "Everything".
#Now, click the arrow next to Details to toggle the Details list active.
#From the details list, check ''Cache'' and ''Cookies'' and uncheck everything else.
#Now click the ''Clear now'' button.
Further information can be found in the [[Clear your cache, history and other personal information in Firefox]] article.
Did this fix your problems? Please report back to us!
Thank you.

Hi, I can't seem to get my ipod 32gb 4th gen to sync with itunes. It's brand new, but everytime I plug it in it says can't access Itunes store and nothing else happens. I enabled my firewall to allow itunes but it still can't access it. Please help.

Hi, I can't seem to get my ipod 32gb 4th gen to sync with itunes. It's brand new, but everytime I plug it in it says can't access Itunes store and nothing else happens. I enabled my firewall to allow itunes but it still can't access the store. Please help.

If you look at the feed, and look at the entry 'The end to an exciting field season in Aulavik National Park' you will see the line:
<pubDateFri, 29 Jul 2011 04:00:00 GMT</pubDate>
You have not closed the 'pubdate' tag - there should be a '>' as the 9th character. Because the tag has been left open, it invalidates everything which follows it, and thus the entire feed. iTunes therefore cannot read it, which is why the Store has not updated. Add the '>' and republish, and all should be well.
It's always worth checking your feed by subscribing manually, from the 'Advanced' menu, or by clicking the 'subscribe free' button on the Store page (both do the same thing) - if you can subscribe to the feed it should be OK.

POTS/Analog Dial Access with PVDM3 and 3900? Possible?

Similar Messages

Maybe you are looking for