Power calibration error when burning?

I get a power calibration error when burning from IDVD.
Any suggestions as to how to fix it?

Basically a power calibration is the drive writes to the blank and then tries to read it back and adjusts the laser power accordingly to get a proper burn. So there are a number of reasons you might get this problem.
One is the media itself. A bad disc or poor quality media might give you this error.
Next, you may have a dirty laser and running on of those cleaning CDs (they have little brushes on them to dust off the laser) might do the trick.
Third, could be a laser on the drive is giving up the ghost. Hopefully it is not the last one.
Patrick

Similar Messages

  • M30-842: Power Calibration error while burning DVD-RW

    I have faced a problem with my M30-842. Several times I have tried to erase burned on my laptop DVD-RW and Nero would say "Burn process failed. Power calibration error". So I cannot erase or continue multisession DVD-RWs.
    Burning CDs is ok.
    Please help me with the problem, how can I solve it? SOS!
    Semen

    Hi Semen
    Can you please try to use roxio software built into Windows XP? There is also the same option. It will be interesting to know if this problem is caused by software that you use or if there is some malfunction of your device.

  • DR4-A power calibration error??

    I bought 50 units of Maxell MXL RG01 dvd-r:s. They are on the recommended disk -document. Everytime I try to burn them with Nero 6, Process goes to 1 percent and I get error message "Power calibration error". I'm having a new Firmware(2.50) installed. Can anyone tell me what's wrong, because MSI doesn't reply my e-mails?

    Hi All
    I just wanted to post some information on the "Power Calibration Error" on the DR8-A2. There are quite a few posts on this subject and yes this error can occur if you are using incompatible media, but if you have been using the media without any problems in the past and then you suddenly start receiving this error then it's not the media at fault and also not the software you are using.  You can try a "DVD Lens" cleaner the wet or dry version and it may work but I have personally found that when you have the "Power Calibration Error" problem these cleaners will not work for the DVD writer.  They do work well for DVD players and DVD ROM drives so don't get me wrong.  The reason so many people get the "Power Calibration Error" on the DR8-A2 drive is really due to the fact that the drives dust proof mechanism is poor and the dust builds up on the lens.  Remember if you get the "Power Calibration Error" when you try a new media then it probably is the media.  Only try the fix given below on the drive if you receive this error on your normal media which you have been using in the past without any problems.  I have now had the problem 3 times and the drive is only 4 months old but have managed to get round it every time.  Although my drive was in warranty I had to break the warranty seal as I didn't have time to take the drive back for exchange.  You will need to open your drive and you will void the warranty so only do this if you are confident enough to do so and at your own risk.
    You will need the following...
    A) Screwdriver to remove your drive.
    B) Computer cotton swabs - (Others may leave cotton deposits so not recommended)
    C) Lens / Head Care Solution - (One that contains ISOPROPYL ALCOHOL)
    D) Paper clip - (Or something of a similar size to eject drive)
    I have gone into detailed instruction only for the benefit of people who have never opened up a CD/DVD drive, obviously people with the experience can skip to step 5 in the instructions.
    Instructions...
    1) Philips screwdriver to open your PC and remove your drive.
    2) Straighten the paper clip and insert it into the "Emergency Drive Eject" hole to eject the drive tray a quarter of the way out and remove the front panel from the tray by unhooking the clips underneath and then sliding up.
    3) Now remove the drives front panel by pressing down on the clips and sliding forward.
    4) Remove the 4 screws at the bottom of the drive and then turn the drive over to slide up the top panel of the drive.
    5) Here’s the delicate bit, you will really need to be very gently now, place 2 or 3 drops of the lens leaner onto the tip of the cotton bud and then very gently wipe the lens side to side. Do not push down on the lens too hard and don’t clean it using up & down strokes.  Do this 8 to 10 times.  Then get a clean cotton bud and do this once more.
    6) You can now put your drive back together in reverse order and the system should work without giving a "Power Calibration Error".
    I hope this helps, I have done this several times now on my own systems and for friends and family, it has worked for me every time.  Like I said earlier the dust mechanism is poor on these drives and in a few weeks time you will need to clean the lens again.

  • Qosmio G20: Can not burn CD's but only DVD's - power calibration error

    Hi
    I'm having some trouble and i think it's very strange.
    I can't record audio or data cd's!
    i've used sonic reducer, as nero, as windows media player..tried 3 different brands of cd'r and i can't burn audio or data files in any of those..BUT...on the other hand i can burn DVD'S...this is very strange right?
    Ps: when i record with nero i keep having this message on the relatory of the burning process : "power calibration error" but only i when i try to burn cd´s.. dvd's recording doesn't have this problem
    do i need to update some drivers?
    please any help would be super or i will have to make a big trip to solve the problem on the laptop shop.
    regards

    "Power calibration" - When burning a CD the drive tries to write a test signal to the disk to set the calibration of the laser. If it cannot write a readable signal, this is called a "power calibration error". The error message usually means that there is something wrong with the media.
    Please try to use few different empty CDs (Verbatim, TDK, Maxell and others).
    Check also this page http://www.cd-burner-help.com/power-calibration.htm
    Maybe helps.
    Good luck!!!

  • IDVD power calibration error?

    Hello everyone. For the past few days I have been trying to burn a dvd from iDVD, however, when it seems to almost finish an error message pops up. ( Error, power calibration error 0x73, 0x03). Can anybody help me?

    Hi FilmStudent:
    Welcome to discussions!
    I think that this is an issue related to the DVD media. Basically, your burner doesn't like whatever brand of discs you've just brought and so you get that weird error message.
    May I suggest Verbatim DVD-R 8x or less? (4x if you can find them).
    :)Sue

  • Medium error: Power calibration error. (0x73, 0x03.)

    Everytime I try to burn a DVD-R in iDVD v3.0.1, I always get the following;
    Power calibration error. (0x73, 0x03.)
    What does that error code mean?
    Any resolution?
    Thanks.

    Hi
    What brand of DVD ?
    I only use Verbatim (Taiyo Yuden DVDs also supposed to be first class)
    What type of DVD ?
    I use only DVD-R
    If You can - try to get an as slow burning versions x1 or x2 - x16 can be problematic
    (alternative is to make a DiskImage of Your DVD project - standard in iDVD 5 and onwards.
    In iDVD 4 You need to do a Hack and use a program named HPfurz, install it and follow instr.
    Then when You have a working DiskImage - burn this at (x1 or) x4 with Apple Disk Util tool or
    Roxio Toast™ if You got this.)
    Else
    *Not knowing the origin to Your problem - General approach when in trouble is as follows.*
    • Free space on internal (start-up) hard disk if it is less than 10Gb should rather have 25Gb
    • Hard disk is untidy. Repair Permissions, Repair Hard disk (Apple Disc Util tool)
    • Delete iDVD pref file - *or rather start a new user/account* - log into this and re-try
    iDVD pref file resides. Mac Hard Disk (start-up HD)/Users/"Your account"/Library/Preferences and is named.
    com.apple.iDVD.plist
    While iDVD is NOT RUNNING - move this file out to desk-top.
    Now restart iDVD.
    • Program miss-match. iDVD 5.0.2, Mac OS X.4.11 AND QuickTime 7.5.5 - is OK - DON’T work under Leopard
    • Program miss-match. iDVD 6.0.4, Mac OS X.4.11 AND QuickTime 7.5.5 - is OK (might work under Leopard)
    • Program miss-match. iDVD’08 v. 7.0.1, Mac OS X.4.11 AND QuickTime 7.5.5 - is OK (might work under Leopard)
    • iDVD (08) v7 Locate theme folder. Move out iDVD1, iDVD 2 and eventually iDVD4 folders to desktop - re-try
    • Try a Cleaning CD/DVD that cleans the laser lens on the DVD burner/player
    iDVD 6.0.4 and iDVD 7.0.1 are compatible with Mac OS X 10.5 Leopard
    Last resort. from Craig. Solved the problem!! Finally!!
    I deleted every iDVD application and folder from my boot drive,
    emptied the trash and then installed iDVD 08 using the customize option
    and I am up and running.
    If You do a re-install be sure to get rid of all iDVD old parts AND then EMPTY the Trash-basket !
    Yours Bengt W

  • Error message - power calibration error

    We are experiencing a power calibration error message when the studetns are buring their edited projects to DVD. Can you give me any advice?

    Moost often, this is due to cheap media, or an incompatibility between the write speed of the media and your drive.
    You might try building the project to a folder on the hard drive and burning a disc of that with toast, which allows you to chooose different burn speeds.

  • Satellite A200-1M8 PAE6E: CD/DVD drive issue - power calibration error

    Hi,
    I have an Satellite A200-1M8 ( or A200 PAE6E ) with Vista and for some time I've been trying to burn some dvds which I failed due to power calibration error.
    I tested my DVD-ROM and it works normally, the problem is it does not read (recognise) every dvd.
    Is there anyone who can help me out about this?
    Or how can I learn which type of media my DVD-ROM would read?
    Thanks in advance.

    Hi
    I think I have founded an interesting article for you:
    [Is there a list of supported type of CD-R/-RW or DVD-R/+R/-RW/+RW/-RAM discs which should be used?|http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=36]
    But generally a power calibration error means that its the media is faulty or not compatible with the drive.

  • Re: Satellite L30-105 Vista - Power Calibration Error - need new firmware

    Hey there guys =)
    Ive got a Satellite L30-105 running a 32-bit Vista. And even if i try several different burning softwares (Imageburn, Nero), and with TDK-cds, I get a error from the burning softwares, saying "POwer Callibration Error".
    The Satellite L30-105 (Article number PSL33E-02S026N5), uses a cd/dvd burner called MAT****A DVD-RAM UJ-850S
    I am wondering, can i download and install new drivers for my dvd-drive???
    i am also gonna try to buy this "cleaning-cd", to try to clean the lense. cause i bought the laptop in 2007... so its like grandma..
    But do u guys have any other what might be wrong?? Is it expensive to get a new cd/dvd-drive for this laptop???
    Cheers and thank u!

    Hi
    Power calibration error means that the ODD laser lens cannot calibrate in the right position.
    Usually this has nothing to do with an drive firmware but with the hardware problem.
    In most cases the CD/DVD drive must be replaced.
    Im not sure how much an new CD/DVD drive could be but fact is that you cannot use any CD/DVD drive
    You need an compatible one and such compatible and supported drive could be ordered from an local ASP.
    greets

  • Unknown error when burning disc

    I get an unknown error when burning playlists to blank discs.  My computer begins to write the discs, but stops after a song or two. 

    Could you post your diagnostics for us please?
    In iTunes, go "Help > Run Diagnostics". Uncheck the boxes other than DVD/CD tests, as per the following screenshot:
    ... and click "Next".
    When you get through to the final screen:
    ... click the "Copy to Clipboard" button and paste the diagnostics into a reply here.

  • Memory allocation error when burning in premiere elements 2

    I have premiere elements 2. I happily burnt a version of my dvd then suddenly it stopped burning and I had the above message during the burning section of the process. My computer has adequate memory to run this programme and nothing new has been added. I then downloaded Premiere elements 7 as a trial and burnt this Dvd yesterday. However today it won't burn through 7 either so i am reluctant to upgrade unnecessarily. Can anyone shed light on why I receive this error message.
    Other things seem to burn but I am beginning to receive messages that Adobe is low generally on memory allocation.
    Regards
    Erika

    memory allocation error when burning in premiere elements 2
    Erika Lindsay - 09:30am Jan 4, 2009 Pacific
    I have premiere elements 2. I happily burnt a version of my dvd then suddenly it stopped burning and I had the above message during the burning section of the process. My computer has adequate memory to run this programme and nothing new has been added. I then downloaded Premiere elements 7 as a trial and burnt this Dvd yesterday. However today it won't burn through 7 either so i am reluctant to upgrade unnecessarily. Can anyone shed light on why I receive this error message.
    Other things seem to burn but I am beginning to receive messages that Adobe is low generally on memory allocation.
    Regards
    Erika

  • Burning Problem - Power calibration error

    hi...
    i use dvd studio pro 3.02 and now when i try burning the DVD my laptop the error message appears.
    "The recording device reported the media error: Power calibration area error. (0x73, 0x03.)"
    i doubt it but is there anyway i can fix that?

    Hi
    You have two things to check:
    - Try a different media. Check this site about * about quality media *.
    - Try creating a disc image in your hard drive and burning it with Disk Utility and/or Toast. Check thsi tutorial: * Creating Disc Image in DVDSP *
    Hope that helps !
      Alberto

  • IDVD 3 calibration problems when burning

    Help! I'm having calibration error messages when burning iDVD-R discs in iDVD 3. I've had success in the past with Maxell DVD-R 8X discs but other brands and other speeds won't work. I can't find Maxell DVD-R 8X discs anymore. Do I need to update the iDVD software? I'm at a loss to figure this one out.
    Swen

    hi sue,
    i purchased the verbatim dvd-r and burned 1 dvd successfully. unfortunately, it will not burn again and i am prompted with the same error message: Power calibration area error: (0x73, 0x03). what is weird is that when i tried to burn a .mov file using toast, i was prompted with an error similar to the idvd error (0x73, 0x03). Could this be a problem with both idvd and imovie? i am able to burn data onto dvds within toast, just not files that i have created using imovie and idvd. i hope this makes sense!
    thanks

  • Power calibration error

    Our Mac Mini Superdrive has stopped burning to discs. It ends the proceedure and reports the following Error message: The device failed to calibrate the laser power level for this media.
    We can't figure out why this is happening. It happens when burning to any disc, from any software. We haven't changed the discs we use and they used to work fine.
    The other interesting anomally is that when I try to get the machine to run a hardware check on start up using the Mac OSX Disc 1, it won't reveal the menu so that I can check to see if the superdrive is working correctly. Instead after about 5mins it goes into safe mode.

    Does this page contain anything useful?
    (14616)

  • Error when burning DVD - no plugin DLLS

    When burning a DVD I get an error message that says Plugin Coder error : no plugin DLLS.  Why is this happening and how can I fix it?

    They do but aren't cheap.
    Look at SuperMediaStore.
    You might be able to find them cheaper. I was just checking to see if they make them.

Maybe you are looking for