Power Keyboard battery is not present

My power keyboard battery is not present. nokia SD-42
Moderator's Note: The subject was changed as we have created a new thread for this topic.

Hi, mananah_Lumia. To verify, you received the Nokia Power Keyboard without a battery, is that correct? If so, where did you purchase it and did you inform them about it? If we got you wrong, feel free to correct us. We look forward to your reply. Good day!

Similar Messages

Battery #2 not present after windows 8.1 upgrade

battery #2 not present after windows 8.1 upgrade. I am using sony vaio laptop model VPCZ2390X

Hi aalmoeen,
Thank you for visiting Sony Community!
I assume your computer has an extended battery pack, right? Are you using a genuine Sony battery packs? Please follow these steps to isolate the issue:
Power Cycle
Turn off the laptop -> push and hold the battery off button for 5 seconds located on the bottom of the laptop. (You may use safety pin).
Remove the battery pack and install it once again. Test the laptop again.
Remove the battery pack -> push the battery off button -> install the battery pack once again.
Reset BIOS
Run Vaio update and Windows update.
Make sure you have the updated drivers and software, check on eSupport website.
For further assistance regarding your concern, please contact the Sony offices/Sony representative offices nearest to your place of residence in Asia Pacific region http://www.sony-asia.com/countryselector.html?hpid=countryselector:AsiaPacific. Due to proximity, they are in a better position to respond to your questions or concerns.
Hope these steps help.
Thanks,
Vincent
If my post answers your question, please mark it as "Accept as Solution"

Battery state not present

Hi everybody
I have a Acer Aspire 5820TG TimelineX which is a really good laptop. But I have a big problem. I can't read the state of the battery.
This is what I get from acpi -V,
Battery 0: Unknown, 0%, rate information unavailable
Battery 0: design capacity 4400 mAh, last full capacity 4400 mAh = 100%
Adapter 0: on-line
Thermal 0: ok, 40.0 degrees C
Thermal 0: trip point 0 switches to mode critical at temperature 105.0 degrees C
Thermal 0: trip point 1 switches to mode passive at temperature 98.0 degrees C
Cooling 0: LCD 0 of 9
Cooling 1: LCD 0 of 9
Cooling 2: Processor 0 of 10
Cooling 3: Processor 0 of 10
Cooling 4: Processor 0 of 10
Cooling 5: Processor 0 of 10
from /proc/acpi/battery/BAT1/state
present: yes
design capacity: 4400 mAh
last full capacity: 4400 mAh
battery technology: rechargeable
design voltage: 11100 mV
design capacity warning: 300 mAh
design capacity low: 132 mAh
cycle count: 0
capacity granularity 1: 32 mAh
capacity granularity 2: 32 mAh
model number: BAT1
serial number: 11
battery type: 11
OEM info: 11
As you can see, ACPI is well aware that the battery is present and its infomation
Some output from dmesg | grep ACPI if it helps
BIOS-e820: 00000000bb73b000 - 00000000bb7bf000 (ACPI NVS)
BIOS-e820: 00000000bb7e1000 - 00000000bb7ff000 (ACPI data)
modified: 00000000bb73b000 - 00000000bb7bf000 (ACPI NVS)
modified: 00000000bb7e1000 - 00000000bb7ff000 (ACPI data)
ACPI: RSDP 00000000000fe020 00024 (v02 ACRSYS)
ACPI: XSDT 00000000bb7fe120 0007C (v01 ACRSYS ACRPRDCT 00000001 01000013)
ACPI: FACP 00000000bb7fc000 000F4 (v04 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: DSDT 00000000bb7ed000 0BA9D (v02 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: FACS 00000000bb75f000 00040
ACPI: ASF! 00000000bb7fd000 000A5 (v32 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: HPET 00000000bb7fb000 00038 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: APIC 00000000bb7fa000 0008C (v02 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: MCFG 00000000bb7f9000 0003C (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: SLIC 00000000bb7ec000 00176 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: BOOT 00000000bb7e9000 00028 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: ASPT 00000000bb7e5000 00034 (v04 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: WDAT 00000000bb7e4000 00224 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: SSDT 00000000bb7e3000 009F1 (v01 PmRef CpuPm 00003000 INTL 20051117)
ACPI: SSDT 00000000bb7e1000 01E0F (v01 AmdRef AmdTabl 00001000 INTL 20051117)
ACPI: Local APIC address 0xfee00000
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x05] enabled)
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)
ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a201 base: 0xfed00000
#6 [0000012000 - 0000016000] ACPI WAKEUP
ACPI: Core revision 20100121
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
ACPI: EC: Look up EC in DSDT
ACPI: Executed 1 blocks of module-level executable AML code
ACPI: BIOS _OSI(Linux) query ignored
ACPI: SSDT 00000000bb691c18 003AE (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
ACPI: SSDT 00000000bb68f018 00891 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
ACPI: SSDT 00000000bb690a98 00303 (v01 PmRef ApIst 00003000 INTL 20051117)
ACPI: SSDT 00000000bb68ed98 00119 (v01 PmRef ApCst 00003000 INTL 20051117)
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62
ACPI: No dock devices found.
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
ACPI: PCI Root Bridge [PCI0] (0000:00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Root Bridge [CPBG] (0000:7f)
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 *7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 *5 6 7 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 *7 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)
PCI: Using ACPI for IRQ routing
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
pcieport 0000:00:01.0: Requesting control of PCIe PME from ACPI BIOS
pcieport 0000:00:01.0: Failed to receive control of PCIe PME service: ACPI _OSC failed
pcieport 0000:00:1c.0: Requesting control of PCIe PME from ACPI BIOS
pcieport 0000:00:1c.0: Failed to receive control of PCIe PME service: ACPI _OSC failed
pcieport 0000:00:1c.5: Requesting control of PCIe PME from ACPI BIOS
pcieport 0000:00:1c.5: Failed to receive control of PCIe PME service: ACPI _OSC failed
ACPI: resource 0000:00:1f.3 [io 0x4000-0x401f] conflicts with ACPI region SMBI [io 0x4000-0x400f 64bit pref disabled]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
ACPI: Power Button [PWRB]
ACPI: Lid Switch [LID0]
ACPI: Sleep Button [SLPB]
ACPI: Power Button [PWRF]
ACPI: Thermal Zone [_TZ] (40 C)
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: WMI: Mapper loaded
ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[Firmware Bug]: ACPI(PEGP) defines _DOD but not _DOS
ACPI: Video Device [PEGP] (multi-head: yes rom: no post: no)
[Firmware Bug]: Duplicate ACPI video bus devices for the same VGA controller, please try module parameter "video.allow_duplicates=1"if the current driver doesn't work.
I'm using the latest kernel from [testing] (2.6.34-ARCH).

docwario wrote:you should try to update the bios with the latest one from acer (actually 1.13),
battery state is now available
I updated BIOS to v1.15 - still no solution. I have, however, found out why I can't see if the battery is charged or not. Appearantly, Acer is not using the standard ACPI spec. Just look at this:
Intel ACPI Component Architecture
ASL Optimizing Compiler version 20100121 [Feb 6 2010]
Copyright (c) 2000 - 2010 Intel Corporation
Supports ACPI Specification Revision 4.0
dsdt.dsl 5231: Method (_Q0E, 0, NotSerialized)
Warning 1088 - ^ Not all control paths return a value (_Q0E)
dsdt.dsl 6596: Name (_T_0, Zero)
Remark 5111 - Use of compiler reserved name ^ (_T_0)
dsdt.dsl 6600: Name (_T_1, Zero)
Remark 5111 - Use of compiler reserved name ^ (_T_1)
dsdt.dsl 6659: Name (_T_0, Zero)
Remark 5111 - Use of compiler reserved name ^ (_T_0)
dsdt.dsl 6663: Name (_T_1, Zero)
Remark 5111 - Use of compiler reserved name ^ (_T_1)
dsdt.dsl 6831: Name (_T_0, Zero)
Remark 5111 - Use of compiler reserved name ^ (_T_0)
dsdt.dsl 6835: Name (_T_1, Zero)
Remark 5111 - Use of compiler reserved name ^ (_T_1)
dsdt.dsl 6894: Name (_T_0, Zero)
Remark 5111 - Use of compiler reserved name ^ (_T_0)
dsdt.dsl 6898: Name (_T_1, Zero)
Remark 5111 - Use of compiler reserved name ^ (_T_1)
dsdt.dsl 7777: Name (_T_0, Zero)
Remark 5111 - ^ Use of compiler reserved name (_T_0)
dsdt.dsl 7870: Name (_T_0, Zero)
Remark 5111 - ^ Use of compiler reserved name (_T_0)
dsdt.dsl 7874: Name (_T_1, Zero)
Remark 5111 - Use of compiler reserved name ^ (_T_1)
dsdt.dsl 7941: Name (_T_2, Zero)
Remark 5111 - Use of compiler reserved name ^ (_T_2)
dsdt.dsl 8008: Method (OEMN, 0, NotSerialized)
Warning 1088 - ^ Not all control paths return a value (OEMN)
dsdt.dsl 8105: Name (_T_0, Zero)
Remark 5111 - ^ Use of compiler reserved name (_T_0)
dsdt.dsl 9124: Name (_T_0, Zero)
Remark 5111 - Use of compiler reserved name ^ (_T_0)
dsdt.dsl 9152: Name (_T_1, Zero)
Remark 5111 - Use of compiler reserved name ^ (_T_1)
dsdt.dsl 9182: Name (_T_0, Zero)
Remark 5111 - ^ Use of compiler reserved name (_T_0)
dsdt.dsl 9248: Method (_WED, 1, NotSerialized)
Warning 1088 - ^ Not all control paths return a value (_WED)
dsdt.dsl 9248: Method (_WED, 1, NotSerialized)
Warning 1081 - ^ Reserved method must return a value (_WED)
dsdt.dsl 9254: Return (OEMN ())
Warning 1093 - ^ Called method may not always return a value
dsdt.dsl 9399: Method (WMBH, 3, NotSerialized)
Warning 1088 - ^ Not all control paths return a value (WMBH)
dsdt.dsl 9456: Method (WMBI, 3, NotSerialized)
Warning 1088 - ^ Not all control paths return a value (WMBI)
dsdt.dsl 9518: Method (WMBJ, 3, NotSerialized)
Warning 1088 - ^ Not all control paths return a value (WMBJ)
dsdt.dsl 9616: Name (_T_0, Zero)
Remark 5111 - ^ Use of compiler reserved name (_T_0)
dsdt.dsl 9661: Name (_T_0, Zero)
Remark 5111 - ^ Use of compiler reserved name (_T_0)
ASL Input: dsdt.dsl - 12143 lines, 396315 bytes, 5129 keywords
AML Output: dsdt.aml - 47766 bytes, 1103 named objects, 4026 executable opcodes
Compilation complete. 0 Errors, 8 Warnings, 18 Remarks, 6 Optimizations
So I properly need to make a correct DSDT table to solve my problem. However, I can't make heads or tails in the ACPI spec document, and most infomation about such a issue is highly outdated.

Lumia 2520 Power Keyboard Battery Level

Apologies to those of you who are still waiting/looking for one of these. Got my free one this week. For those that do have one, I guess you have noticed that the Battery icon in the system tray on the desktop lets you see both the tablet and the keyboard power status, Charged, percentage, not charging, etc.
My tablet gets to 100% just fine. The keyboard has never seen above 87%, and at that point actually says 'not charging'. I can drain it some, and plug it back in and it will show the keyboard charging, but it hasn't got above 85-87% and then says it has quit. What do you guys see? Normal? Problem?

My Lumia 2520 with Nokia Power Keyboard shows Battery #1: Fully charged (100%) and Battery #2: 0% available (plugged in, charging). However, even after more than 8 hours plugged in and showing "charging", Battery #2 never shows more than 0%.
The tablet was a used gift,but the keyboard is new, ordered online from Verizon. It has done this from the first time using the tablet with the new keyboard. As far as I know, the tablet never had a keyboard attached until now. All keyboard functions appear to work properly and all tablet functions appear to work properly. I used the tablet with the keyboard for several hours unplugged and the Battery #1 disharged to about 80%. When I plugged it in, Battery #1 charged up to 100% and then it showed Battery #2 plugged in and charging, but never changed from 0% available on Battery #2.
I have tried the Power button and +Volume button technique with no change. It does go throught the stages of showing 0%, not charging on both batteries and then after resetting it goes back to showing the same issue of never showing an increase in Battery #2charge % beyond 0%.
Nokia telephone tech support had me go through that same exercise with no fix. I also refreshed Windows to see if a driver was corrupt with no joy.
None of the nearby Verizon, AT&T or Microsoft stores have the Nokia Porwe Keyboard in stock so I ordered another keyboard from Verizon and if it works then will get a refund on this one that isn't working.
If anyone has any other ideas on how to get the keyboard battery to show that it is charged beyond 0% then please let me know so I won't be returning a good keyboard thinking it is defective.

Tecra A9, Power connected - battery is not charged

I use a Tecra A9. It is about 3 years old now. But I seem to have a problem with battery recharging.
Connected to external power it is functioning oke. But the battery is not been recharged anymore. When removing the powercord, the laptop is running on battery power.
I removed the battery from the laptop and reinserted it. Then it is recharging for several seconds and than stops charging again. Remaining charge is at this moment at about 90%.
I also removed it and cleaned the contacts in the laptp and on the battery. But the same happened. Some seconds recharging, than it stops charging.
What could be the problem?
Thanks in advance for your reaction(s).
Kind regards,
Ren

>Connected to external power it is functioning oke. But the battery is not been recharged anymore. When removing the powercord, the laptop is running on battery power.
I think the problem is the battery.
Its old and cannot hold the charge anymore. So you have to replace this battery.
Check the part number of this batter.. it should be placed at the back side of the battery.
Then you can google for this part in the net to get the right battery.
Greets

Wireless Keyboard Battery Level Not Changing?

Hi,
I have got a new iMAC machine 21.5" , almost 6 weeks since. I am a regular user. The machine has Mountain Lion OS 10.8.2.
In System Preferences, I can see the Battery level for Blue tooth mouse dropping to 57%, but the keyboard has been showing 100% all the time.
Looks like this is a bug. How do i check the Keyboard Batter Level.
Regards,
Vinay

I bought an 21.5" iMac eight months ago and I did note that the battery level wasn't changing for my Wireless Keyboard as my Magic Trackpad slowly used its batteries up. That being said I changed the batteries in the Keyboard when the Magic Trackpad died assuming the Keyboard was soon to follow and now the battery level is reported accurately. In conclusion I believe that the Energizer Advance batteries that are shipped with the Wireless Keyboard, Magic Mouse and Magic Trackpad had a lot more to do with the problem then the OS. I don't know why only the Keyboard was affected but I do know that now I am using regular Energizer batteries and all is normal as far as usage levels. Hope that helps.

No Mains Power or Battery Chargeup, Not a Battery or Power Adaptor Fault

I have an iBook G4 12" purchased March 2006. It's been heavily used but the only problem I've had with it was last year it developed a tendency to shut down without warning. This was solved by taking the battery out and hasn't been a problem since I replaced the power lead. So otherwise no problems with the computer.
I mostly use it on the mains but a couple of times a week have it for 30 mins on battery. A few weeks ago it started to struggle charging up afterwards. A change of "routine", eg. plugging it into a different socket or adding the extension to the power adaptor, would trick it into working again. But the problem got more frequent until, a couple of weeks later, it was charging up then suddenly switched into battery mode and has been stuck there ever since.
I have changed the battery and power adaptor and this has made no difference.
A couple of odd things to note: using the old battery (5 mins a day for emergencies) it had got down to 35% then the Software Update launched and the battery suddenly dropped to 0% and went to sleep. This is when I had to buy the new battery. Also, when I pull the plug out of the mains with the barrel connector still in the computer, instead of the LED going out instantly it stays on for 10 seconds then fades out.
I've had a couple of tricks suggested that have failed: powering up through the mains with no battery in, also pressing ShiftControlOption for 5 seconds before powering up.
Please does anyone have any suggestions as to what might be wrong? Thanks.
Message was edited by: ValW

The charge and run issues may be related to a failing DC in-board.
You may be able to get the correct part and replace it yourself, or
have a repair tech do the task for parts-plus-labor charges.
There are some DIY pages online, such as those from iFixit:
http://www.ifixit.com/Browse/iBook_G4
Good luck & happy computing!
+{ PS: Hello, and welcome to Apple Discussions! }+

Battery #1: Not present

Two days ago the tablet was just running fine without being connected to the keyboard.
Right now as soon as I`ve plugged it out it stops running - no battery.
I can't even turn on helix without keyboard.
Solved!
Go to Solution.

I just opened the tablet by myself, and I found that the connector of the main battery is lose.
So I just pressed the connector lightly, and it works well now!!!
here is the instructions of how to open the tablet, just so easy
http://support.lenovo.com/en_US/product-and-parts/detail.page?&DocID=PD026804
http://support.lenovo.com/en_US/product-and-parts/detail.page?&DocID=PD026805

Keyboard Backlight ALS Not Present

My back light has always been working in the past but never noticed it not working until today because I haven't been using it at night anymore. It's no longer working! pressing the F8,F9, & F10 doesn't even bring up the adjustment on the display.. also, going into the keyboard preference.. I no longer see the option to enable/disable the illuminate keyboard. What is going on here? is this a 10.4.2 update bug or something? Anyone have the same issue?

Welcome to Apple Discussions.
First, rule out a software problem by creating a new user account with administrative privileges and look to see if the checkbox appears in System Preferences while you are logged in to that account. If it does, then delete the file com.apple.bezelservices.plist from yourusername/Library/Preferences in your original administrative account, then log out and back in again or restart.
If the checkbox doesn't appear in the new user account, move the file com.apple.bezelservices.plist in your Macintosh HD/Library/Preferences folder to the Desktop and log out and back in again or restart and check to see if the checkbox appears in System Preferences in your main Admin account.
If none of these things correct the problem, then it is likely that you have a hardware issue. If it is a hardware issue, it may be something relatively minor, like a loose connection between the ALS and the logic board, which is easy to fix, or it may require a logic board replacement.
Let us know how the troubleshooting goes. Good luck.
Tuttle

Split x2 battery not present

Hi,
If i have my computer docked in the keyboard, it will not work unless i have the power cord plugged in. It will keep chiming and the wifi light will blink. Also then when i do plug it in and click the power icon it shows battery # 2 not present. Or sometimes it will just show battery #1 and not even show that there is a battery # 2. I've attempted to run the battery check however it only comes back as battery 1 is good and doesn't give me anything for battery # 2. Any help or ideas would be greatly appreciated.
Thanks

Hi ZachHopper,
Welcome to the HP Forums!
I would like to take a moment and thank you for using the forum, it is a great place to find answers. For you to have the best experience in the HP forum, I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I understand you have a battery problem. Because it cannot be found you are unable to test or calibrate it.
I suggest contacting HP support for assistance with this issue.
Please call HP technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region HP Technical Support Sitemap.
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

Battery 1 plugged in, charging. Battery 2 is not present

Hello,
I have an HP Elitebook 8440p, like three months ago it started to shut down everytime I unplugged the AC power, and to not cherging the battery at all, then appered a message "battery 2 is not present". I recently changed the battery, it is bigger since I thought it would be better, but now it is out of charge and I am on the same problem, plugged to the AC power but it is stocked on 1% of charge, it says Battery 1 is plugged in, charging; baterry 2 not present; but do not charge the battery at all, if I unplugged the power my notebook shuts down.
I tried following some steps I found posted on some other users, but nothing works out.
Please help me.
Thank you.

Hello diegoL90,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I have read your post on how your notebook computer is producing an error message: "Battery 2 not present," and I would be happy to guide you towards a resolution!
I am sorry, but to get your issue more exposure, I would suggest posting it in the commercial forums, since this is a commercial product. You can do this at:
http://h30499.www3.hp.com/t5/Notebook-HP-ProBook-EliteBook/bd-p/bsc-274
I hope this helps!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

Hp Envy states second battery not present

My second battery states not present. Please help me to solve this issue. I love this compuuter. And my warranty have already expired.

@razalijamsuri ,
Welcome to the HP support forums and thank you for posting. So that I can better help you with your battery issue, I will need a little more information. Here are some links to check out first.
Advice for asking the "Very Best Question"
Could you post back with your full model and product number.
How Do I Find My Model Number or Product Number?
As well when you state a second battery. Is it an hp original part or is it a third party battery.
Any information would be great. Please include your notebooks Operating System as well.
Which Windows operating system am I running?
I hope to hear back from you soon. Have a great day and thank you again for posting.
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
D5GR
I work on behalf of HP

HT1547 My mac book pro is 3 yrs old and today while watching something on it, it got power off suddenly. And power button is not working, left side round button to battery is not working but when I plugg in to charge it, then this round button shows 4 gre

I am having MacBook Pro 3 yrs old and today while I was watching some movie on it suddenly it got power off and when I am trying to start it, it's power button is not working even the round button on external left side is not showing battery lights. But when I connect it to chrger then Charger only gives green light and even the external round button only shown 4 green lights (if charger connected). I don't know what to do now

Sounds like you need a #1SMC Reset
1. SMC reset
>>Instructions to reset SMC
Disconnect other non-Apple and external hardware except (if applicable) a mouse and keyboard until your finished repairing your machine.
Problems solved: Fans blowing with no activity, machine is not booting, power button pressed and nothing happens, problems with indicators, Magsafe has wrong lights, battery is not charging, monitor and graphics issues etc. If the battery is not charged (from like letting it sleep too long), let the Mac charge up awhile afterwards.
Will not hurt the machine resetting if it's not broken.
Other related hardware problems (optional):
Check battery status: Hold option/alt key down while clicking on the battery icon in the menu bar, top right corner.
Magsafe: Use the correct/matching power supply charger with your Mac, not a less powered one from another Mac.
Apple: Laptop won't power up Apple: Computer won't power up Troubleshooting optical drive
Magsafe problems Magsafe problems more

T60 will not power up (battery status led green, power status led green)

Ok so I have been researching this for a couple days now. Trying various things............
Including the famous 10 second power button press discharge.........
Symptoms:
1st Disclaimer - coffee was exploded all over the laptop but has been running for a month.
Symptoms:
It has been working post coffee spill (several weeks ago) as long as you left it running. I get cocky and turn it off then it wont come back on.
The laptop has exhibited the inability to power on since but I have been able to get it to turn on several times since.
green power light comes on with AC adapter only
plug battery in and the battery light goes green
press the power button - both lights go out
I replaced the keyboard, battery, tested for 20 Volts on the AC adapter, tested for 2-3 volts on the CMOS battery.
I tried testing for 20 volts on the motherboard where the power supply cable connects. I have most of the laptop broke down still.
I did get it running again last night as a result of me incorrectly using the multimeter and short circuiting the power supply connector .
It booted up and ran fine and I even tried turning it off and on again several times.
I thought it might be a heat issue. I turned it off and tried to turn it on this morning and it will not power up.
Same symptoms as before.
no battery, only power connected, green light comes on, plug in the battery, battery light goes green, try to turn it on and the lights go out.
It seems like it is fixable but I am not sure what to look for next.
Or should I be looking for another system board...........if so what should I replace it with
This is an IBM T60 Type 2613 15" screen.
Solved!
Go to Solution.

Welcome to the forum!
Your best bet would indeed be a new system board. Any single one from a non-widescreen T60/p will work.
I've got dozens of them available - send me a PM if you're interested.
Good luck.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

My hp mini 110-3700 laptop say battery not present

My hp mini 110-3700 laptop say battery not present, but i can see the battery s/n under the system info

Please how can i fix this? I need your help please

Power Keyboard battery is not present

Similar Messages

Maybe you are looking for