Power Mac G4 shows this when turned on..

Please help. Not sure what to do. My friend says my HD failed. If I buy Disk Warrior would that help?

Q: would I need a SATA pci card in order to install a SATA hard drive to my power Mac G4 that uses IDE? I
Yes, Best Buy was wrong... unless you maybe got an IDE to SATA adapter...
http://www.amazon.com/Ide-Pin-Female-sata-Adapter/dp/B001PYSAJI
But you can still get ATA/IDE/PATA drives...
http://eshop.macsales.com/item/Western%20Digital/WD5000AAKBRC/
http://eshop.macsales.com/item/Western%20Digital/WD3200BEVE/
http://eshop.macsales.com/item/Western%20Digital/WD1600AAJB/

Similar Messages

My user account doesnt show up when turned on, just a gray screen on my Mac mini.

My user account doesnt show up when turned on, just a gray screen on my Mac mini. Please help. I have lots of unsaved data on it.

Gello, see if this works...
If 10.7.0 or later...
Bootup holding CMD+r, or the Option/alt key to boot from the Restore partition & use Disk Utility from there to Repair the Disk.

Power Mac G4 Gigabit won't turn on

My power mac g4 gigabit won't turn on. When you press the power button on the front it lights up for a seccond and then it turns off and the computer doesn't turn on. If you hold the power button down the light stays on but when you release it it turns off again. only the light on the zip drive comes on sometimes. I have tried to reset the PMU but that didn't do anything I took out the battery and replaced it but it didn't help.
PLEASE ANYBODY HELP ME!
Thanks,
rcrickarby

first of all, i'm an AMIGA guy. i did my share of apple ][ programming in the late 70's, but this is the first mac i've touched (literally) since 1985 when i played with the original mac. in 2000, i finally went from the amiga (i still have lots of 'em) to the Dark Side and got a PC (QUAKE II, DUDE!) running Windows NT, then Windows 2000, now XP. i finally retired that machine this year - i gave it to a neighbor for his kids.
now back to the topic...
i'm working on a friend's G4 gigabit machine which had a bad power supply (no 28V output). as a replacement supply is obscenely expensive and they apparently die early and often, i've got an ATX supply in there (let go my ears - i are an engineer and i know what i'm doing).
i'm currently feeding +5V standby from the ATX supply (+5 always hot, even when supply is "off") to the +28V trickle pin of the motherboard power connector. i'm not worried about firewire or ADC monitors at this point.
besides the power supply hack, i'm using a PC mouse & keyboard (USB) through a belkin flip KVM.
the machine works fine now, except:
1) if i let it put itself to sleep (power saver setting), it wakes up brain damaged. the screen is corrupt, the mouse pointer is present and moves, but it's for all intents and purposes dead and must be reset. if i put it to sleep with a quick push of the power switch (throbbing power light mode) and then wake it back up (after waiting seconds or hours), it's fine.
2) if i disconnect the AC (even briefly), it won't power back up until i reset the PMU. i bought a new battery at radio shack today (didn't realize they wanted ****$19.00**9.00** for the thing until i saw the numbers on the register!), and i'm giving it an overnight charge with everything powered up before seeing if that fixes things. interestingly, i came home with the new battery, and of course the machine wouldn't start as i had left it unplugged. popped the old battery out, put the new one in, and it started! of course, i excitedly shut it down and unplugged the AC for 5 minutes, but it wouldn't start until i did the PMU reset
i realize that either of these problems could be related to using only +5V standby for trickle power, but keep in mind that previous G4 machines (yikes/sawtooth) also used "standard" +5V trickle power, so i'm not breaking any new ground.
what else might be going on to prevent it from starting up when freshly plugged in?
i'm looking at two solutions for the 28V thing - one is an off-the-shelf DC to DC upconverter which turns 5V to 24V (and can even provide 2A if i diode-OR +5V standby with +12V), and the other is something i'll whip up myself using an LM3478 and a big FET which can provide 1A @ 28V from 5V. either of these should be enough to run powered firewire things, but again no ADC monitor.
system stats:
G4 gigabit, 400MHz, 1G RAM (512M PC133, 256M PC133, 256M PC100), 4.2.8f1 firmware, OS X 10.4.11
i saw a message in one of the system startup logs about the video card firmware being "too old". is there a way to update the firmware? here's what system profiler says about it:
ATY,Rage128Pro:
Chipset Model: ATY,Rage128Pro
Type: Display
Bus: AGP
Slot: SLOT-A
VRAM (Total): 16 MB
Vendor: ATI (0x1002)
Device ID: 0x5046
Revision ID: 0x0000
ROM Revision: 113-72701-125
one last thing - when the machine is asleep (throbbing power light), i assume the DRAM is on and being refreshed. how much current does that require at 28V?
i'm pleasantly surprised by how quickly it boots and shuts down. the "identify your keyboard" thing was weird, but effective. the UI is a little better than 1985, but still seems a little cryptic - and that's from a guy who still uses VI to edit software.
my only other apple experience since 1985 is an iPod Shuffle, which is cool once you get hold of a certain perl script to rebuild its database. until you do that, you're saddled with iTunes. i've only used (or tried to) the Windows version. i don't think i've ever used any software on any platform that was so LARGE, so SLOW, so INTRUSIVE to the rest of the system, and so COMPLETELY OPAQUE before (well, maybe ClearCase). dear apple - don't do THAT again.

My mac keeps on loading when turning on. I cant get in with my mac. how to settle it?

My mac keeps on loading when turning on. I cant get in with my mac. Any idea how to settle it? Or should I reset my mac?

Hi..
Try Resetting the System Management Controller (SMC)

Power Mac G4 shows only screensaver image; won't read disks

My Power Mac G4 will no longer show the finder or any of my folders. It boots beyond the grey and blue screens to show a screensaver I'd chosen earlier, but doesn't show the finder or any of my folders. It will not read any of its original install disks, nor read the OS X Panther disks.
I don't know if its versions are current. It has no internet card, which has not been a problem until now as I also use a G5 that's on a cable modem.
I got this computer second-hand. It came with these disks:
Apple Hardware Test (Power Mac G4)
Power Mac G4 Software Install
Power Mac G4 Software Restore
Power Mac G4 Developer Tools
Mac OS X Panther Install Disks 1, 2 and 3
I have tried installing them all from the screensaver mode, as well as from CD mode. Nothing has been forthcoming. Is my data still present? Does the OS X need to be installed, or has the system just stalled in the booting? I've rebooted a dozen or more times while working with the disks. Since I'm getting beyond the grey and blue screens, is this a sign of life?

Hi t_orzechowski!
Have you found a resolution yet?
Have you ever run Repair Disk?
THESE ARE THE STEPS FOR USING DISK UTILITY TO REPAIR YOUR HD
1.Insert the System Install disk, Mac OS X CD-ROM disk, or Restore DVD disk, then restart the computer while holding the C key. Use the System disk, of the OS, that is currently installed.
2.Once started up from CD or DVD, on the Menubar at the top of the screen, choose Disk Utility from the Installer contextual menu.
Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from disc to access Disk Utility.
3.Click the First Aid tab.
4.Click the disclosure triangle to the left of the hard drive icon to display the names of your hard disk volumes and partitions.
5.Select your Mac OS X volume, if necessary.
6.Click Repair. If DU reports errors it has fixed, re-run Repair Disk until no errors are reported.
7.Repeat steps 5 & 6, but select the Hard Drive this time. It's usually the first listed with the manufacturer's model number. Make note of the S.M.A.R.T. status.
8.When finished, select Quit Disk Utility from the Installer menu.
9.Select Quit Installer from the Installer menu.
10.In the resulting pop-up window, choose restart.
11.After the computer has restarted, you can eject the CD.
ali b

Power Mac G5 Showing Prohibitory Sign on Start Up?

Earlier this week my Power Mac G5 1.8 ghz dual started to show a prohibitory sign on start up. The hard drive was original to the machine (from 2004) and I wanted to upgrade it to a larger size anyhow, so I put in a new hard drive thinking that might solve the problem and give me an upgrade at the same time.
After I installed the new hard drive, I formatted it and did a restore from Time Machine of my system. When I restarted, I got the prohibitory sign again. I restarted holding down the option key to see if it found the new drive and it did. So I selected the new drive and it started up from the new drive with my restored system on it with no problem. Then I went to system preferences and made sure the new hard drive was selected as my start up disk. On restart, I got the prohibitory sign again.
Then the weirdness started. On subsequent restarts, I get the prohibitory sign intermitently whether I'm starting from the hard drive, my Leopard installation DVD, my Disk Warrior boot disk, or my old Panther installation disk. It seems to boot without any problem from the Apple Hardware test CD. I've run the extended apple hardware test and it didn't find any problems. Most of the time, I get a prohibitory sign no matter how I'm trying to boot up, but sometimes it will boot from the Leopard installation disk or the hard drive, but when it does, it freezes after running for a few minutes. I've tried swapping out the memory sticks and it's made no difference.
Is it possible this is a software problem and not a problem with the motherboard or other hardware? I sure hope so, because I love this machine. Anyone have any suggestions about what I might try next? I've read about the "hair dryer" solution, but if Apple Hardware Test didn't find any probemms with the memory or motherboard, could that still be a solution?
Thanks for any help or suggestions.

Thanks, japamac. Yep, I should have said I replaced the old hard drive with the new one. So, it now only has the one, new fresh hard drive. The new drive is a WD Caviar Blue 320gb.
I set the jumpers on the new drive for 5-6 to slow the new drive down to 1.5. I've also tried resetting the PRAM several times, and tried restarting in safe mode. Every few tries I can get it to boot from the hard drive or a boot DVD/CD (maybe once every 10 tries), but it freezes up after running for about 10 minutes. The only instance this doesn't happen is if I boot with the Apple Hardware Test CD. It didn't freeze up during the 2 hours it took to run the extended test.
Thanks for trying to help me.

Power Mac g4 freezes up when put in sleep mode

Hello. So the machine has had a lot of changes but the problem just started a couple days ago, before that I was going into sleep mode just fine with no problems. The problem is when the computer goes to sleep it freezes, the screen goes black but the fan and hard drive are still going and the light never turns to the flashing amber. What's more I'm unable to wake it up or use the keyboard restart command. The only way to restart or shutdown are the buttons on the tower. So I've turned power saver off and now have just resorted to shutting down when it's not in use but that's pretty bad in the long run.
Any ideas on what may have started causing this? Like I said it's beem working perfectly for a while now.
Here's info on the machine
I'm running a modified AGP G4 stats as follows:
Machine Name: Power Mac G4 (AGP graphics)
Machine Model: PowerMac3,1
CPU Type: PowerPC G4 (3.3) (Power Logix dual 1.3)
Number Of CPUs: 2
CPU Speed: 1.3 GHz
L2 Cache (per CPU): 256 KB
L3 Cache (per CPU): 2 MB
Memory: 1.75 GB
Bus Speed: 100 MHz
Boot ROM Version: 4.2.8f1
System Version: Mac OS X 10.4.9 (8P135)
Kernel Version: Darwin 8.9.0
Classic 9.2.2
ATI Radeon 9200:
Chipset Model: ATY,RV280
Type: Display
Bus: AGP
Slot: SLOT-A
VRAM (Total): 128 MB
Vendor: ATI (0x1002)
Device ID: 0x5960
Revision ID: 0x0001
ROM Revision: 113-A27502-124
Displays:
SyncMaster:
Resolution: 1440 x 900 @ 60 Hz
Depth: 32-bit Color
Core Image: Not Supported
Main Display: Yes
Mirror: Off
Online: Yes
Quartz Extreme: Supported
Display:
Status: No display connected
ATA ST3200822A:
Capacity: 186.31 GB
Manufacturer: ATA
Model: ST3200822A
Revision:
Removable Media: Yes
BSD Name: disk2
OS9 Drivers: Yes
SCSI Target Identifier: 1
SCSI Logical Unit Identifier: 0
S.M.A.R.T. status: Not Supported
I also have a 60 gig HD installed which is currently not being used
Thanks again in advance.
Aaron

Did you install a USB 2.0 PCI card and do you leave bus-powered devices connected to it, when the computer goes into sleep mode? There have been many reported sleep issues associated with USB 2.0 cards in the G4s. What name is printed on the main controller chip (sometimes it's hidden by the card manufacturer's label)? The consensus of opinion is that USB 2.0 cards with an NEC chip tend to have fewer problems. Additionally, it's a good practice to disconnect the bus-powered devices from the card, prior to letting the computer go into sleep mode.

Power Mac G5 Shuts Down When Waking From Sleep

I picked up a Power Mac G5 for a song at work. It had OS X Tiger 10.4.11, 1 GB RAM and 160 GB HDD, I've since upgraded the RAM to 2 GB, the HDD to 1 TB, and installed OS X Leopard 10.5 from an install disk I had bought when it first came out, and then upgraded to 10.5.8. It works and does what I want it to do.
It refuses to wake up from sleep since I first brought it home.
When it goes to sleep, the power light pulses like it should. However, when I move the mouse or press a key, it does a hard shutdown imediately. I've explored the suggestions here and searched on the internet for a solution.
Here is what I have done:
1.     Unplugged everything but the keyboard and monitor
2.     Replaced the keyboard with another white one that had never been used
3.     Replaced the battery on the Logic Board
4.     Pressed the SMC button on the Logic Board
5.     Did a PRAM reset
6.     Erased, partitioned the disk, and reinstalled Leopard from scratch
There are no extra programs loaded, only Leopard and the programs that came with it.
I've changed the Energy Saver Preference Pane to never sleep:
This is not going to kill me if the best option is to never sleep.
Everyone have a nice day.
Boyd

Boyd Porter wrote:
It is on an APC ups, so it could be a flaky power supply. At least it doesn't do any spontaneous shutdowns, yet, so I can live with it. If it dies, I will buy a new MacMini.
I had a similar sporadic problem with my G5 on a UPS which was failing. The surge on wake was enough to sag the power causing the PSU to kill the power supply. The UPS finally tanked and getting a new one cured the problem. You might see how it reacts on normal mains power as an experiment.
Also, never underestimate the capacity of a G5 power supply to accumulate dust, which reminds me that it is time I blew out my power supply dust, since it's been about a year since the last cleaning.

POWER MAC G4 MDD WON'T TURN ON

i went to turn on the computer and it wont turn on? i need it to work it is my only mac and only computer i have i am on a library computer now. i have over $750 in parts and upgrades on this computer.
G4 MDD 2GHZ 2GBRAM 3 750GB HD'S 512 MB VIDEO CARD DVD-RWDL 2 USB 2.0 CARDS ONE SATA CARD

Whew, could be a bunch of things, how old is the PRAM Battery?
Might be time to replace the PRAM Battery, 4 years is close to their lifespan, far less if ever without AC power, & can cause strange startup problems...
http://eshop.macsales.com/item/Newer%20Technology/BAA36VPRAM/
How to reset the SMU/PMU on a Power Mac Earlier G3, G4, G5 models...
http://support.apple.com/kb/HT1939
Remove the PRAM Battery, AC power, all peripherals, including Monitor, Mouse, KB, everything, let sit a few hours or overnight... replace everything & try starting it up.
Might also reseat any PCI cards & Graphic card.
https://discussions.apple.com/message/15009563#15009563

I still have the problem with my Power Mac G3 Blue/white. Turning the power on i can hear it go thru POST but nothing every shows up on the monitor screen. Also when booting pressing the "C" or the Shift key nothing happens.

I don't get anything on the monitor screen. During startup i can hear it going thru POST but never any screen image. Any ideas?

The "C" key will work if there is a bootable volume on a disk in the optical drive. Are you running OSX? Jaguar, Panther, Tiger? On OSX (UNIX) you can use the command "S" (⌘-S) at start up to go to the root and do a file system check: Type; fsck -f -y at the prompt when it appears then press Return; let the root check for problems and repair. To exit after the test type; reboot and press Return

Mac Pro Power Supply making noise (even when turned off)

Hi everyone,
My Mac Pro Early 2008 (Dual quad core 2,8) began to make noise a while ago and it drives me mad.
The sound is (100% sure) coming from the Power Supply. The sound is not mechanical, but electrical, like an oscillator crackle sort of.
First I thought it was the PSU itself, so I had it replaced with a new one, but that did not change the situation.
The (new) PSU makes excactly the same noise, even when my computer is turned off (but still connected to the power socket in the wall).
I've eliminated all possible factors that could create an interference (other electrical devices). I even completely switched off the power of my office, except for one power socket; the one I used to test the Mac. As soon as I connected the Mac, as soon the noise came back. So, it's got to be inside the Mac.
So my question is: if it's not the PSU, nor the power of my office, what could it be?
PS: I've tried a UPS too... but that did not change a bit.
Thanks for your suggestions!

Hey
I appreciate the attention and help from you guys. I installed hardware monitor and this is what tells me:
Ambient Air 22
CPU A Heatsink 28
CPU B Heatsink 29
CPU Core 1 27
CPU Core 2 30
CPU Core 3 29
CPU Core 4 27
Expansion Slots 32
Hard Drive Bay 1 30
Hard Drive Bay 2 25
Hard Drive Bay 3 24
Hard Drive Bay 4 24
Memory Bank A Point 1 38
Memory Bank A Point 2 44
Memory Bank A Point 3 44
Memory Bank B Point 1 37
Memory Bank B Point 2 44
Memory Bank B Point 3 48
Memory Module A1 65
Memory Module A2 65
Memory Module A3 62
Memory Module A4 54
Memory Module B1 69
Memory Module B2 65
Memory Module B3 59
Memory Module B4 57
Northbridge Heat Sink 63
SMART Disk Maxtor 6V300F0 (V60E4NQG) 41
SMART Disk ST3500630AS P (9QG0H24P) 31
Do you have any suggestions? is it safe to find a program to regulate the fan of the power supply down or can this damage the system?

New 8 Core MP passing power to firewire ports even when turned off???

Is anyone else noticing this? Even after you have turned the power off to the MP 8 core, power continues to travel through the firewire ports?

Some FireWire functions work with the computer off. See:
<http://developer.apple.com/documentation/HardwareDrivers/Conceptual/HWTechFireWire/Articles/FireWimplementation.html>
and
<http://developer.apple.com/documentation/HardwareDrivers/Conceptual/MacPro_0801/Articles/ProductDeveloperNote.html#//appleref/doc/uid/TP90005242>
"When in sleep, the Mac Pro has 25 W of power available to the USB and FireWire ports, and memory. If the combined USB and FireWire port power load exceeds the available power, power to those ports will be cut to preserve memory."

It seems that I have lost all my photos/catalogs on my Mac - Lightroom 5. When turning on Lightroom there are no photos listed and nothing comes up.

Upon turning on Lightroom 5 on my Mac Book Pro there are no photos listed in the Library. I do have external backup but need to understand what might have happened that I have lost the photos and how to get them back into lightroom. I was editing earlier in the day and now nothing! It is as though I never imported any photos - says photos 0.

Look under File->Open Recent, try the catalogs listed there.

My Power Mac G4 shows AAAAAAAAA on the desktop after startup

What should I do to resolve the problem? Please help me.

Everywhere. It appears as blinking AAAAA's on the top bar and on a screen that looks like the Documents folder. In the folder, everything is AAAAAA's. When you click on something like iTunes, this little window will pop up and say....
AAAAAA AAAA AAAAA AA AAA AAAAA.
...or something like a paragraph of AAAAAAA's.
This more helpful?

Mac Pro showing black and white lines when booting up

Hello Apple community,
My Mac Pro crashed yesterday after it was reading an empty DVD, and now if boot the Mac it shows this screen:
I have tryed rebooting it in safe mode, does not work, I get the same screen.
Tryed to use a other monitor, same problem.
Now, If I press the Eject button, the disc tray will eject and if I press the volume button it can be heard.
Need some help
Thank you in advance.

Nevermind I found out that my videocard is broken.

Power Mac G4 shows this when turned on..

Similar Messages

Maybe you are looking for