Power Mac G5 Hard Drive Dead?

So the other day I tried to format my internal hard drive using my leopard server install disk that I bought for my power mac but I got the error Resource Busy. Then I used my Tiger install disk to format the drive and got the error Input/Output error. I ended up putting the hard drive into a PC I had and used it to format it to FAT. After that I put the hard drive back in my Power Mac G5 and it showed up as FAT and I formatted it to Mac OS Extended (Journaled). I took a 250GB drive I found and also stuck it into the G5. Formatted it into Mac OS Extended (Journaled) and tried RAIDing them together using a Concatenated Disk Set so I could get the full usage of my 250GB and my 1TB drives. The raid failed with a error I can't remember. Now the 1 TB drive won't show up at all. The PC says it is a unknown device and needs drivers. What do I do. I have tried everything I know. Do I need to buy a new drive (why couldn't it be the 250 GB drive )

That drive series has had a bunch of issues.
Fixing a Seagate 7200.11 Hard Drive
The Solution for Seagate 7200.11 HDDs - MSFN Forum
Firmware Check - Support - Seagate
Seagate fixes 7200.11 drives--except when it doesn't | Crave - CNET
Seagate Barracuda 7200.11 drives failing- The Inquirer

Similar Messages

  • Power Mac G4 hard drive a goner?

    Hello,
    My Power Mac G4 "died" last Sunday. Initially, the it wouldn't start up at all. So, after reading some suggestions on the net (I have a Mac Book pro), I changed the battery.
    It booted but the question mark folder came on. I couldn't even open the CD tray. Further reading had me use the command-option-F-O during start up and I finally got the install CD in.
    I booted via the CD but when I went to utilities, my hard drive was nowhere to be found! It just showed the DVD drive and a USB flash drive that I had.
    I called the local Mac service shop and he said that it would take from $50-1000 to diagnose and perhaps fix the problem.
    Can I salvage my hard disk? Or is it a goner?
    Thanks guys.

    To start with, anyone who would give you such a ridiculous ballpark figure of $50-$1,000 to diagnose/repair a G4 with an AWOL hard drive has lost touch with reality. Depending on which model G4 that you have, its market value may be substantially less than the upper figure quoted. The fact that the hard drive isn't detected on the bus, would likely indicate that it has an electronic and/or mechanical problem. If either is the case, none of the software solutions ("DiskWarrior" or "Data Rescue") will work, because they require a mechanically-functioning hard drive. You can check the data ribbon cable for abrasions in the insulation that may have caused a short, but that's probably a long shot. You should also check that the power connection is plugged securely into the back of the drive, even though it's typically such a tight fit, that it rarely comes loose. The possibility of unexpected hard drive failure is the primary reason for routinely backing up the data, so you only need to worry about buying/installing a replacement. Professional data recovery companies can retrieve data from the most severely damaged hard drives, but the cost is quite expensive for the home computer user. If you don't have files on the hard drive that you need to retrieve, I'd suggest replacing it with a new one. If you post back with the G4 model/processor speed that you have, a compatible replacement can be recommended.

  • Upgrade Power Mac G5 Hard Drive: But New Drive Doesn't show up??

    Hello,
    I have a Power Mac G5 1.8 (circa 2003).  I bought it in 2003 and it has travelled all over the world with me. I love it.  It has been the best and most reliable computer I ever owned; and I'm trying to keep it humming along as long as possible.
    I am currently running Leopard (OS 10.5.8).
    I have 2.5 GB of Ram (I upgraded 2 GB a few years back)
    I have currently run out of room on my Hard Drive 160GB - the original one that came with the computer.
    I purchased a Seagate Barracuda 2TB Hard Drive (Seagate ST2000DL003) to replace the 160GB one.
    However, when I tried to replace the drive - it wouldn't show up on my computer.  I could see it appear on screen when I looked at Disk Utility but not in the window that allows you to select a drive? - and continue the installation process?  did I buy the wrong kind of drive?
    I'm 100% sure I'm doing something wrong.  I just have no clue what it is?
    Could someone please help; or point me in the right direction?
    I'm not a computer whizz; nonetheless I'm not affraid to dabble in DIY.
    Many Thanks
    foginwater

    Hi foginwater, just asking since you don't specify, did you use Disk Utility to Format it for Mac yet?
    How to format your disks...
    http://www.kenstone.net/fcp_homepage/partitioning_tiger.html
    Thanks to Pondini, Formatting,  Partitioning, Verifying,  and  Repairing  Disks...
    http://web.me.com/pondini/AppleTips/DU.html
    And if you would like to just have everything on the old drive transferd to the new ine...
    Get carbon copy cloner to make an exact copy of your old HD to the New one...
    http://www.bombich.com/software/ccc.html
    Or SuperDuper...
    http://www.shirt-pocket.com/SuperDuper/
    Then you can hold the Option/alt key down at bootup to choose the HD to boot from when completed.

  • I have an iMac running Lion and W7 with boot camp . It has been operating flawlessly until I went to reboot into Mac tonight. Screen went black, and system is unresponsive. I've tried force quitting and turning power off. Hard drive starts but that's it..

    I have a 5 month old  iMac running Lion and W7 with the latest version of boot camp . It has been operating flawlessly until I went to reboot into Mac tonight. Screen went black, and system is unresponsive. I've tried force quitting and turning power off. Hard drive starts, there's a small amount of drive activity and that's it. 

    Hi Jane, your info may still be there, look in the Users folder at root of the drive, how many users are there there?
    It sounds like this may have happened...
    Return to default desktop, apparent "loss" of home directory, (it can happen spontaneously too)...
    http://docs.info.apple.com/article.html?artnum=107854

  • Hard Drive Dead? Help!

    Hi, so I recently bought an enclosure for my old HD that died out on me, I suppose? My mac was asleep, then I pressed any button on the computer to wake it up, then I clicked on Mail right away, and it froze for a while.. so I held the power down to restart it. When it restarted, it gave me a white screen with a folder with a question mark on it. I was told my HD was bad. So I changed it, now my mac is up and running. BUT... i need my old files from my old HD. I bought an enclosure, plugged and played.. nothing comes up. How can I get my old files? Please help!!!!

    This one has an outside chance of working. But if it doesn't work, _be warned_, might make the data completely unrecoverable through a professional data rescue service. I've only heard about this and never done it myself. You put it in the freezer. Not sure why this is supposed to work, but it might.
    _Much safer to try Data Rescue first. I would try this only as a last resort._
    For others, try googling hard drive dead freezer and see what you think.
    http://hacknmod.com/hack/how-to-recover-dead-hard-drive-data/
    I can tell you from experience that it in fact DOES work…most of the time. I have managed to recover data 3 times from dead drives, and have also not managed to recover data about the same amount of time. So, it is fair to say that for me, it worked 50% of the time.
    I placed the drive in two zip lock bags expelling as much as air as possible before zip locking both bags. I left it in the freezer for approx. 12 hours with no luck, but after freezing it for extended periods of time, it worked like a charm. It is also important to note that this is generally a one shot deal, if it works, you’re in luck, but you must get as much data as possible from the drive because once it dies, it is rare that you will gain access a second time.
    The 3 times I did manage to get the data back, I exhumed only the data that I absolutely required. In other words, only the data I created or files that I placed on the drive.
    I too, found it hard to believe when I first heard it, but after losing 3 years of tax returns I HAD to try it. Fortunately for me, it worked like a charm.

  • Gray folder with question mark-- is my hard drive dead?

    I have a white 13 inch MacBook that is about 3 years old and runs on Mac OS X 10.4 (I believe). In the past year, it has been running more and more slowly and programs keep freezing. I was going to ask for more RAM for Christmas, but decided to try a few maintenance steps first. I ran a VirusScan this morning (using McAfee), and when I came back into the room, my computer had frozen past all help. I powered it off with the power button, and now, when I try to start it, a gray screen appears with a question mark. I have tried some of the support steps listed to get it working again such as trying a safe boot (didn't work) and resetting my PRAM (didn't work). Is my hard drive dead? Is there any way I can get my files off the computer? I haven't backed up in about 3 months, and I am very upset because I have a lot of important papers and photos on my HD.
    Thank you..

    Hi corimazz and welcome to Apple Discussions!
    It is possible that your hard drive has kicked the bucket, but the folder with the question mark just shows that the computer cannot find a valid system when it starts up. There are a number of possible reasons for this.
    Do you have the 10.4 install disk? If so, insert it into the optical disk drive, restart the computer and hold down the C key during startup. Once the computer is booted to the install DVD, select your primary language, then look for the utilities menu and from it select "Disk Utility".
    In the Disk Utility, you should see a list of available disks, which we hope will include your hard drive. If the hard drive does not appear in the list, it is dead. If it does show up, select it and click the "Repair Disk" button to see if the problem is being caused by directory damage that can be repaired.
    If the drive is truly dead, you are going to have to decide how much the data from the last three months is worth to you. There are companies that have quite good records of recovering data from even very badly damaged hard drives (sunk in rivers, burned in fires, etc) but they are not cheap.
    In the USA some data recovery options include:
    DriveSavers.com - 800-440-1904
    www.ontrack.com - 800-872-2599
    www.lazarus.com - 800-341-3282
    Once you have the drive out (it's a simple process to remove) it can be replaced with a new one.
    I hate to say it, but keeping backups of important files is vital to safe computing. Both the Leopard and Snow Leopard operating systems make this a much easier process using the "Time Machine" application.
    Best of luck.

  • My Passport for Mac external Hard drive is not recognized

    I recently had to purchase a new MacBook Pro, and when I tried to get files off of my Passport for Mac external hard drive.  I get an error stating "The disk you inserted was not readable by this computer."  And when I try to initalize, and verify disk, I get this message "Partition map check failed because no slices were found.".  I have already updated firmware for the external hard drive.  One site I found stated that it could be that the USB port is not strong enough, and I would need a 2.0 Booster cable.  Does anyone know if this would work? 

    What did you old Macbook die from?  Likely the HD in it is still ok,  yes?
    You can remove the HD inside your old dead Mac and put it into a $20 HD enclosure or HD dock, and remove the photos that way, very easy.........IF your old Macbook died from something other than ALSO a bad HD.
    You said----my OLD Macbook pro which recently lost video
    What happened with your old "dead" macbook?  Still have it?

  • What would happen if my mac os hard drive failed

    so i have 2 hard drives
    1 for windows bootcamp and 1 for mac
    as it is now, i boot to the windows boot manager then choose my copy of windows.
    what would happen if my mac os hard drive failed right now?
    would the computer still boot and be unaffected unless i tried to boot to mac?

    failure is usually not dead. It can be a bad sector, but usually it is a directory issue or just the partition table (but which require either quick or long format)
    if you have a workstation, you should clone both operating systems; you should not put them on the same hard drive. And you just use the clone you made for each (Paragon Clone OS for Windows $19; Carbon Copy is sharefare for OS X)
    both of those allow booting off the new hard drive while you figure what you want to do or what happened.
    If you only have two hard drives use the other drive bays.
    Basically NOTHING happens if you pull one or the other.

  • My Mac Book  hard drive is nearly full. How do I move  iTunes music, etc folders to a different location on an external hard drive and still access as if on my Mac?

    My Mac Book  hard drive is nearly full. How do I move  iTunes music, etc folders to a different location on an external hard drive and still access as if on my Mac?

    http://support.apple.com/kb/HT1449

  • My mac mini hard drive is failing. I am no longer under warranty. Do you know how much it cost to have Apple replace the hard drive? or How I can replace it myself?

    MY mac mini hard drive is failing. I am no longer under warranty. Do you know how much it cost to have Apple replace the hard drive? or How I can replace it myself?

    You can do it yourself. I did on my 2009 Mini
    http://www.ifixit.com/Device/Mac_Mini
    Also, this place sells HSDs and has install videos.
    http://eshop.macsales.com/installvideos/

  • Moving Garageband Music Files to MyBook for Mac External Hard Drive on OSX 10.5.8  I'm a musician and need to make space on my mac hd. Is it safe to move music files there and delete them on the mac? Thanks!

    use a MyBook for Mac external hard drive.
    I need space on garageband or the entire hard drive, since I am getting the "need space on the hard drive" messages.
    It's scary to move my precious music files!
    How should I move them to the external and feel safe about doing so?
    Or are there other methods besides the obvious, clearing caches, deleting the trash and downloads, etc., that are recommended?
    I am doing music now and producers are waiting for the new vocals!
    Help!
    Thanks!

    The process is as simple as just copying your Garageband project to the external drive and deleting from the macs hard drive. But before you delete anything you really need to back them up to someplace else also. Having just one copy is not safe. Get another external drive, DVDs or even flash drives, you absolutely need anything important in more then one place.

  • How do I get finder to recognize my hard drive after pulling my hard drive out without eject...? Is my hard drive dead? I see it in disk utility... Can I get my info back?

    I have a seagte back up plus. I pulled my hard drive out without ejecting it and now finder dosn't find it but I see it in disk utility (although I cant repair permissions) How do I get finder to recognize my hard drive after pulling my hard drive out without eject...? Is my hard drive dead? I see it in disk utility... Can I get my info back?
    Thank you so much for any help

    In Disk Utility you need to see a volume or partition in addition to the drive.
    If all you see is the drive, then when you ejected it you proably corrupted the volume or partition on the drive.
    If that is true then your chances of getting anything back are slim at best.
    About the only thing I know that might work not is to send the disk out to a service for recovery. This is going to cost like $$$$.
    Is the data worth that much?
    Allan

  • Using non-mac external hard drive with time machine

    Is it possible to use a non-mac external hard drive (ie, anything other than Time Capsule) connected to Airport Extreme with Time Machine?
    If so, how do I make the external hard drive visible in the back up disk list?

    see this [link|http://www.macworld.com/article/132613/2008/03/airporttime.html].

  • New to MAC, External Hard Drive Problem Transfering files to MAC

    Hello All.
    First I'm new to the MAC world, just bought my powerbook pro yesterday. Love it. I tired looking for this topic and found similar post but no solutions that I understood.
    10.4.9
    I have a 260GB NTFS external hard drive with about 100 gigs of info on it. I used it with my PC, running XP Pro.
    I want to be able to access that HD from my MAC but all I can do is read, I cannot write. I was hoping it would just hook up to my MAC and I'd be able to read and write.
    I do not need to be able to use this HD with my PC anymore. I'm 100% MAC now. I was hoping someone could give me some advice on how to make that happen. Do I have to reformat my HD? What system is that FAT32, NTFS? Something else? And how do I go about doing it?
    Thanks to all.
    D-Power

    Welcome to Apple Discussions!
    You are correct, Macs can only write to FAT32, or Mac formatted hard drives with the built-in software, unless the Mac is networked to the PC, as this article describes:
    http://docs.info.apple.com/article.html?artnum=19652
    You can also add Macfuse to the Mac, to connect to an NTFS drive, and that's linked here:
    http://code.google.com/p/macfuse/
    To reformat the drive, you'll have to erase it with Applications -> Utilities -> Disk Utility. Thus before you can reformat it, you'll have to copy over any essential information. The Partition section under Disk Uitlity lets you create a GUID Mac formatted partition under its Options button, and that is ideal for both Intel iMacs and MacBook Pros. If the label under the screen says Powerbook, let us know, and we'll direct you to that forum instead, if we can't answer your question here. Apple Partition Map on the other hand is the ideal for Powerbooks, and PowerPC based Macs. Formatting GUID or Apple Partition map, will let you boot from that drive, to verify that a clone backup was done properly depending on which Mac you made the clone for. Formatting FAT32 or NTFS won't let you make a full backup of your internal hard drive, and only will let you use it for backing up user documents. I highly recommend Shirt-pocket Superduper for backing up, as my FAQ* explains:
    http://www.macmaps.com/backup.html
    P.S. The MacBook Pro is the Intel version of the Pro notebooks. You posted to the Intel iMac forum. The Intel iMac looks like: . So unless you have that Mac, you are in the wrong forum. There is no such Mac as the Powerbook Pro. You'll see the label in front says MacBook Pro below the screen if that's what you got. Here's the forum for it for category reference:
    http://discussions.apple.com/category.jspa?categoryID=190
    And pick a forum within it to post a new topic, if I can't answer your question here.
    In addition, this nomenclature article will be helpful as well:
    http://discussions.apple.com/thread.jspa?threadID=503342&tstart=0
    * Links to my pages may give me compensation.

  • Creating Partition in Mac Mini Hard Drive

    i Have buy a mac mini a week ago, but before three days ago, some file got corrupted, and it does not start, only the password screen appears, when i entered the password, the screen appears again. and it continues. Now i want to partition the mac mini hard drive. i have only one drive, and i want to create another partition in the hard drive. when i create another partition  through the disk utility , i gives error, and cannot create the partition. i acutally want that first i make partition in the hard drive, and after using the "restore from time machine option" to install the mac osx lion in the system. Please help me in make the partition in the hard drive.

    Apple themselves don't specify hard drive RPM because they buy a number of different drives, some apparently 4200 some apparently 5400.
    It's no surprise that your retailer wants you to buy a G5 though, and is trying to upsell one based on the minis weaknesses - after all, they get more money from a G5 sale than from a mini. They may also be considering your planned use of Photoshop as a stumbling block to effective use of a mini, but the question really is what you intend to use Photoshop to do. If you're a hobbyist, the system is fine and will work more than adequately - particularly if you max out the RAM. If you're a professional user with pro-level expectations, then a mini likely wouldn't be sufficient, not so much due to the drive speed (powerbook users have run Photoshop verisons for years quite happily on what are predominently 4200rpm drives) but because for pro work, Photoshop needs a lot of hard drive space and a great deal of RAM.
    On the basis of what you've posted, I'd say your retailer is more interested in their profit than your need. Chances are, if you run PS on the G4 listed in your profile, you're already running on a drive of similar general performance.

Maybe you are looking for

  • Can't Open any files in photoshop CS3

    I can not open any files in Photoshop CS3. It has been working fine. I was using camera raw and did not open the file and now can't open any file in photoshop. I reinstall it photoshop and it did not work. I reinstall install window xp worked fine un

  • My Macbook Air is running slow with Yosemite.

    My Macbook Air is running slow with Yosemite. I checked out most of the blogs and everything and have removed widgets from the notification center, but everything seems to run kinda slowly. Sure, i have the base model 2014 macbook air but that 4 gb r

  • RE-FX features differeing in ECC 6.0  and 4.7

    Dear all Please give some pointers on which are the features that are available in ECC 6.0 of real estate not available in  SAP R/3 4.7.flexible. Also in the first place need some under standing whether in 4.7  flexible real estate can be used. Regar

  • More than one form accessing a PayPal account

    My plan is to have one Adobe Forms Central account. I would like to set up two different forms (one for registratants and one for Exhibitors) and have both of them access the same PayPal Standard Business account to use their credit cards. Is this po

  • ClassCastException on getObject()

    I'm using the thin driver Oracle JDBC 8.1.5. When I execute the following syntax: callStmt.registerOutParameter (1, java.sql.Types.INTEGER); callStmt.execute(); //correctly executed Object value = callStmt.getObject(1); Integer pk = (Integer) value;