Power Mac G5 wont install 10.5 on new hard drive

I recently got a Pmac g5 from my uncle. His hard drive died and he had no further use for it. I bought a new drive and have a disk for Leopard, but when I try to load from the disk it doesnt seem to work. it just defaults back to the ? folder. The disk works because it loads fine on my G3 iMac, and I dont know how to check to see if the hard drive is recognized (250 GB Maxor formatted for this computer). I've reset PRAM and all that stuff, but with no luck. Any help as to why it wont work?

Well Option Boot won't see the Hard Drive ubtil we fornat it HFS+, but whyit isn't seeing the Install Disc is our problem.
Does the G3 iMac haveFirewire?
If so wee could use the G3's Optical drive with the G3 in Target Mode, & Option Boot the G5.

Similar Messages

Power Mac 7200/120 won't boot off new hard drive. Says HD "not supported"

I just recently came into possession of a PowerMac 7200/120. The only thing it came with is a boot cd with Mac OS 8.1. It booted fine off the cd with only the date/time issues of a dead PRAM battery, but when I tried to boot the internal HD on its own, it was a no-go. Flashing ?. When I tried to verify the HD, the software would not even find the HD. Not even listed on the program. You can't initialize what isn't there, so I ordered a new HD from an online vendor. I replaced it according to the directions on the Apple .pdf file I googled. I also reset the logic board and replaced the PRAM battery. Upon booting after all this ... still flashing ?. I run the same verification process as before and I actually DO see this HD listed, but it says it is "not supported" and doesn't allow me to initialize it. It's virtually the same quantum fireball HD with the Apple logo as the old one I just took out, just a different GB size. Connections and slots are all the same. Is this just not the right HD for my computer? Is there something I need to download? I just rebuilt a Performa 6300cd with ZERO issues.

Ok ... a couple of mistakes on my part which of course could change EVERYTHING. I'm embarassed with the amount of mistakes in my own question. A couple of forgetful omissions on my part ...
#1. The drive DID start up just fine upon first switching out the HD. Original software on HD was 8.1, but as I needed to run older programs not compatible with 8.1, I initialized and installed 7.5.3 clean. (I know ... HUGE omission here, but be kind as I've been working on multiple computers and it has been a couple months since I did this). It worked fine after download. After coming back to this computer a couple of months later, I get the flashing ? again (like before the HD switch).
#2.The HD the online vendor sent me was not the one I ordered, but ended up being a carbon copy of the one I took out except the GB size (which was actually larger than the one I ordered). Didn't physically count the pins, but it plugged in fine. Everything fit.
#3. I also forgot to mention that while the CD drive worked, the floppy either spat my disks out at me or asked to initialize them. These were the same floppies that I took out of my Performa literally a minute earlier (which worked).
#4. The 8.1 cd is a mistake on my part again. Turns out it's the black-faced 7.5.3 cd (7200, 7500, 7600, 8500, and 9500 series). Got confused with the 8.1 drive.
UPDATE
The strangest thing ... I just booted up off the cd and it's now reading the HD. I ejected the cd and booted it up on its own ... and it works just fine. I did NOTHING since I asked the question. In fact, I just booted the computer back up in response to your response.
Before I delved into these boards and bothered to ask for help ... I had opened it up, cleared out a TON of dust bunnies with my can o' air, pressed the CUDA? chip, and then replaced the PRAM battery. Restarted holding down cmd-opt-p-r until it chimed again and it was still a flashing ?. You could hear it clicking as if trying to start the drive up at regular intervals. I restarted the computer well over 10 times hoping it was just something jammed up in the HD (though just bought) and it was the same flashing ?. And now today ... did nothing and it boots up just fine. I check the drive setup lite and it now shows macintoshHD there (instead of unsupported drive - original showed nothing at all).
Does it take time for the PRAM battery or logic board to reset? Did it just needed a thorough internal cleaning? Or should I chalk this up as just being a really old comp?
I really don't want to go delving back into it now that it's working to check the SCSI terminations, jumpers, etc. I'm going to assume those are ok now it's booting.

How to install Windows 7 on new hard drive?

I have changed the old hard drive (500 gb) with a new hard dirve (1 Tera), and now I have two problems: -
1. How do I install Windows 7 on new hard drive?
2. My laptop was pre-installed Windows 7 Pro, but all the DVD kit (Application & Drives Recivery Disc + Operating System Revocer), which was provided (by Lenovo) for the laptop is in the Windows 8 Pro. So how do I install Windows 7 Pro, in my laptop while all DVD kits are in Windows 8 Pro?
by the way this is my laptop spec (for reference) ; -
* Note *
I plan to install Windows 7 Pro in my new hard drive using another Windows 7 DVD (Not DVD provided by Lenovo), but how do I get all the Leveno program which found within the 'Application & Drives Recivery' disc (such as ; - Lenovo System Health and Diagnostics, Lenovo Power Control,Lenovo's Fingerprint Reader) to install in that hard drive? (as I tell you before, all the DVD kit is in or only for Windows 8 Pro)
I hope somebody will help me answer my question,
Thank You
Solved!
Go to Solution.

I got the solution;
Answer to question 1 ; using a backup & recovery software to clone my current OS, then transfer to my new hard drive.
Answer to question 2 ; download all the Drivers and software ( all the application that located on the DVD kit that I have) on Lenovo Official Website.
or other solution, send it to a computer service shop and let the experts ( the workers) install it for me ( the most simple and safe way).

How to install and reconfigure a new hard drive?

How to install and reconfigure a new hard drive?
I installed a new hard drive from best buy for my "vintage" MacBook laptop. When I turned on the laptop and the flashing folder appeared, I need help?
I looked online for some clues. I put in the software disk I received when I bought the disk but I cannot select a destination volume to install the software. I tired to partition the drive within disk utility but there was an input/output error. Should I just plug in my external hard drive and hope everything reboots like magic ?
Thank you for any help you can give

How to replace or upgrade a drive in a laptop
Step One: Repair the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger, Leopard or Snow Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
Step Two: Remove the old drive and install the new drive. Place the old drive in an external USB enclosure. You can buy one at OWC who is also a good vendor for drives.
Step Three: Boot from the external drive. Restart the computer and after the chime press and hold down the OPTION key until the boot manager appears. Select the icon for the external drive then click on the downward pointing arrow button.
Step Four: New Hard Drive Preparation
1. Open Disk Utility in your Utilities folder.
2. After DU loads select your new hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID then click on the OK button. Click on the Partition button and wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
Step Five: Clone the old drive to the new drive
1. Open Disk Utility from the Utilities folder.
2. Select the destination volume from the left side list.
3. Click on the Restore tab in the DU main window.
4. Check the box labeled Erase destination.
5. Select the destination volume from the left side list and drag it to the Destination entry field.
6. Select the source volume from the left side list and drag it to the Source entry field.
7. Double-check you got it right, then click on the Restore button.
Destination means the new internal drive. Source means the old external drive.
Step Six: Open the Startup Disk preferences and select the new internal volume. Click on the Restart button. You should boot from the new drive. Eject the external drive and disconnect it from the computer.

Any ideas on how I install Lion on a new hard drive

Any ideas on how I might install Lion on a new hard drive when I purchased the OS online from Apple prior to my hard drive failing? I don't have a disk.

when you install your new drive, what happens? it should boot into internet recovery and you setup from there.
does it not do that?
here is an article about how to force internet recover http://www.cultofmac.com/106669/force-lion-to-start-internet-recovery-on-your-20 11-or-later-mac-os-x-tips/
here is apple literature about the recovery partition (if you had a hard drive) http://www.apple.com/osx/recovery/
here is a do it yourself downloader that makes a usb stick the recovery disk. If you have data on the usb drive I would back it up, as this will erase everything else on the thumb drive. http://support.apple.com/kb/DL1433

Installing Mavericks on a new hard drive...

Hi
My hard drive crashed, and I bought a new one today. They told me at best buy I need to download mavericks drivers onto a usb or something. I'm not really sure what they meant so I thought I would ask here. Where do I go to put Mavericks onto a usb to install it on a new hard drive?
Thanks

1. If it shipped with 10.7 or newer, you'll need to go through that OS by following the instructions above, and then install Mavericks in the normal way. If it shipped with 10.6.8 or earlier, reload that OS from DVD and then upgrade to Mavericks.
2. The computer's firmware contains instructions for connecting to the Internet.
(100250)

My conputer crashed and I want to install cs4 onto a new hard drive, how can i do this the registration won't let me?

My conputer crashed and I want to install cs4 onto a new hard drive, how can i do this the registration won't let me?

What does "the registration won't let me" mean? If the serial number is rejected, contact support by web chat. for anything else you need to provide proper technical information and actually explain your issue.
Mylenium

I purchased mountain lion from apple but never got a disk. How do I install it on my new hard drive, old hard drive failed and is not recoverable according to Apple and Recovery Specialist?

I have a mid 2009 MacBook Pro with newly installed SATA HD + SSD, I can get mavericks download free but I can't recover photos, apps, files etc from time machine (1TB Time Capsule), I think I was running lion when I started backing up on it but I had updated to mavericks before the HD Failure. When I tried to transfer info from Time Capsule it says " no volumes detected" or something to that effect. I had mucho info backed up on that capsule. Any help appreciated, please spell it all out for me if you can help, I am not at all tech savvy and desperate to get up and going as I am an online student with a fast approaching deadline for course paper. Thank you in advance :)

Step 1: Buy a new Hard drive that can be installed in your MacBook Pro later, and an External enclose to place it in for now.
The MacBook Pro before 2010 can not contain the stand-alone firmware to go to the Internet and get a fresh copy of Mac OS X and install it.
You will need a working Recovery_HD, or to drop back to a 10.6 DVD (if it will Boot on your Mac).
There may be a functioning Recovery_HD on your existing Boot Drive. If you were running 10.7.4 or later and Time Machine, there may be a Recovery_HD on the Time Machine Volume.
To check:
Hold down the Alt/Option key as you restart. This will slowly draw a gray screen and then add an Icon (over several minutes) for each potentially-bootable volume. If any Recovery_HD shows up, take it, and you will be able to get to Internet Recovery and re-download some version of Mac OS X that can be installed on a new drive.
It is generally far quicker to set up a new drive and install Mac OS X than to struggle with only the primitive tools available only on a DVD or a Recovery_HD. Once you get any version of Mac OS X running, you can get some work done and attempt to salvage first your data, then your drive (if either will be possible).
By NOT trying to Boot from and use the possibly-damaged drive, you improve your chances of being able to salvage some files off it, since blocks will not be over-written by running Mac OS X from it.

Can I install OSX on a new hard drive without a CD?

I'm receiving a replacement hard drive in the mail in a few days, as my current HDD has failed. Although I don't have an OS X disk. My Macbook is a mid 2012, will I be able to reinstall the OS via OS X Utilities when I get the new hard drive? Or will I need to launch Internet Recovery?

Your current HD will be removed from the Mac? If it has failed the recovery partition will also be unusable. You will need to use Internet recovery
OS X: About OS X Recovery - Apple Support scroll down for internet recovery info.
It will install 10.7 since that shipped with the Mac, upgrade post install to whatever OS you have in your App store account.
P.S. connect via ethernet to speed the whole process up (WiFi can be much slower).

Installing Windows 8 on New Hard Drive

I am not very computer literate so please bear with me.
The hard drive went bad in m Hp Pavilion 15 Notebook PC last week. I ordered a new hard drive from H P and installed t this morning. I found a video online and the installation was quick and simple...a piece of cake!
However, I am now having major difficulties with the intallation of my operating system. I purchased Windows 8.1 and when I put in the CD it tries to install, I think, but then I get a message that says "Selected boot image did not authenticate. Press <Enter> to Continue. " I have tried this numerous times and I always get the same thing...and pressing enter does nothing.
I learned on some of the forums that there is something I may do in bios to change how it boot ups. However, I cannot get into the bios to make the changes that they say I need to make.
Please help me!

Hi,
Try the following.
Shutdown the notebook.
Tap away at the esc key as soon as you press the power button to enter the Start-up Menu and then select the Bios Menu ( f10 ).
Under the System Configuration tab, expand the Boot Options Menu.
You need to set Secure Boot to Disabled and Legacy Devices to Enabled.
When done, press f10 and select to save the changes.
You may then have to enter a 4 digit pin displayed on the screen to confirm the setting changes - enter the code and hit enter.
Insert the Windows 8 installation disc and Shutdown the notebook.
Tap away at the esc key as soon as you press the power button to enter the Start-up Menu and then select the Boot Options Menu ( f9 ).
Use the arrow keys to highlight the CDROM (uefi) option and hit enter - if prompted to 'Press any key to continue....' - do so.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

How can I install OSX into a new hard drive without a CD?

I just installed a new hard drive and I don't have a installation CD/DVD to install OSX. How can I go about install a fresh copy?

Are you able to beg or borrow access to another Mac that has access to the internet & is new enough to use the App store?
You can sign in to your App store account & download the appropriate installer (Mavericks or whatever you have in your account). Then you can make a USB bootable copy of the installer (there are many other guides around)…
http://osxdaily.com/2011/07/08/make-a-bootable-mac-os-x-10-7-lion-installer-from -a-usb-flash-drive/
If you can access a Mac but don't want to do the huge download you can use the recovery assistant to create a bootable recovery partition on a USB stick.
https://support.apple.com/kb/DL1433
When you boot your Mac it will download the OS for installation.
Does the original HD still work? It may be quicker to get a cheap 2.5inch case & boot from that just to get an OS downloaded & installed. It will mean you are not wasting cash & time on 10.6 that is only needed for one App store download.
I'd consider a trip to an Apple store if you have one local, they may drop an installer or recovery partition onto a memory stick for you.

Installing Os 10 on new hard drive

How do i install a fresh copy of mac OS 10.. on a new hard drive.. I have the Tiger cd's. I really need to get my mac back up n running.
Message was edited by: ChinyBwoy

First prep the drive:
Extended Hard Drive Preparation
1. Boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger or Leopard.)
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Click on the Options button, set the partition scheme to GUID (only required for Intel Macs) then click on the OK button. Set the number of partitions from the dropdown menu (use 1 partition unless you wish to make more.) Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the volume(s) mount on the Desktop.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
After formatting has completed quit DU and return to the installer. Now proceed with the OS X installation.

Install OS X on new Hard Drive

I am planning to upgrade my macbook's 60gb hard drive to 120gb.
My question is, How do I install OS X on the new hard drive?
Please advise.
Thanks.

wow, your way seems a lot more simple compared to this one...
http://www.mac-forums.com/forums/showthread.php?p=276354
it looked a little complicated and i was just wondering if these steps are alright to follow. if not, then how do i go through this process without messing everything up? i haven't done anything yet, and i'm trying to figure out the right way to switch my almost filled hard drive with my new one.
i just ordered a 160GB seagate drive for my macbook and an external enclosure from OWC.
sorry, i'm new to this stuff.
-jan
Macbook Core Duo, Mac OSX (10.4.8), 2.0Ghz, 2GB RAM Mac OS X (10.4.8)

Installing from DVD to New Hard Drive

I have recently purchased a MacBook Pro, and a new 500 gig hard drive to use in it. The new hard drive is mounted using a hard drive dock. While attempting to install Snow Leopard on the new hard drive from the MacBook Pro's DVDs, I get the following message:
"Snow Leopard cannot be installed on this computer."
Is there any way to install a fresh version of Snow Leopard onto this new hard drive from these DVDs?

First prep your drive as follows:
Extended Hard Drive Preparation
1. Boot from your Snow Leopard Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID then click on the OK button. Click on the Partition button and wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
Upon completion quit DU and return to the installer. Complete the OS X installation.

Installing OS X on new hard drive

I'm having a bit of a problem with my G5. I installed a new hard drive, but can't install OS X onto it. When I run the CD and I have to select a destination drive, nothing comes up. I ran the hardware test and there are no issues with the hard drive, so it recognizes it somewhere at least. But it doesn't want to come up when I actually go to install the operating system.
Any input? Thanks!

Your G-5 iMac should have come with a system restore DVD. It should be gray in color and say "Mac OSX install Disc 1 " on it. You need to insert the DVD and then restart the computer while holding down the "C" key until you see the splash screen. Then you can release the "C" key until it completes the boot process. At that point you should be able to begin the process of installing the system by following the steps. Is this what is not happening for you?
If you are trying to start up and do an install from a different disc, say one from another Mac it may not work. Of course a retail 10.4 disc should work without a problem.

Power Mac G5 wont install 10.5 on new hard drive

Similar Messages

Maybe you are looking for