Power Mac goes to the blue screen and no where

I had a Power Mac G4 Dual 1, processor. Upgraded to 10.5 and after I cleaned up some files and was ready to reboot system and when I brought the system backup it went to blue screen. Now I can not do anything else on the system. I want to restart to a clean install if I can.

Start with http://support.apple.com/kb/TS1545 If that doesn't solve the problem, restore your previous Tiger bootable backup/clone.

Similar Messages

I have a PB G4 that won't start. It shows the gray apple screen, shows the blue screen, and then the screen goes black, and "sleep" light pulses.

I have a PB G4 that won't start. It shows the gray apple screen, shows the blue screen, and then goes black. The sleep light pulses. From there, I can't turn it off normally. I have tried restarting the PMU. And I have tried unplugging the ac adaptor and removing the battery. From there I have plugged only the ac adaptor in, and it will begin to start but do the same thing once it shows the blue screen.
I tried only using the battery (without plugging in the ac adaptor) and the same thing happens. I tried starting the computer while holding down CTRL, Option, P, and R, waiting to hear the start up chimes 3 times, and then holding Shift as it starts up. But I still get the black screen once I see the blue one, and the computer's sleep light pulses.
I need something very important from this computer. And was able to start it last night. I did not shut down the computer, and was going to take it to a friends to use his printer today. The computer was in sleep mode in the morning.
Thanks for any help!
Gina

What your describing could be a logic board or memory issue.
You did or did not hear 3 startup chimes? If you hear 3 chimes when you start it, that would indicate a memory problem. Try reseating the memory to see if that makes a difference. If you have 2 RAM cards, try one then the other in each slot. If you have 1 RAM card, move it to the other slot. Powerbooks can develop one bad slot.
You may need to pull the hard drive out of the Powerbook, put it into an external case, then read it from another mac.

When i plug my Ipod touch 4th generation in it goes to the apple screen and then it will turn off and then back on to a solid blue screen.

When i plug my Ipod touch 4th generation in it goes to the apple screen and then shuts off and then turns back on and goes to a solid blue screen.

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

Upon start up I get a start up disk full message and to delete files, now I only get a a blue screen on start up. How to I get past the blue screen and how do I delete files?

Upon start up I get a "start up disk full message, delete files". Now on startup I only get a blue screen. How do I get past the blue screen and how do I delete files.

That;s really not enough free space... you can use a tools such as OmniDiskSweeper to find out where your large files reside and begin pruning (or copying to an external if they're files that you want to keep).
One thing is certain - if you're going to continue your current usage you're certainly going to need to install a larger boot drive.
Clinton

My ipod only goes to the apple screen and freezes then turns off after about a minute. Is this fixable?

My ipod only goes to the apple screen and freezes then turns off after about a minute. Is this fixable?

Try a system reset. It's quick, easy and harmless...
Hold down the on/off switch and the Home button simultaneously until the screen blacks out or you see the Apple logo. Ignore the "Slide to power off" text if it appears. You will not lose any apps, data, music, movies, settings, etc.

G5 Power Mac (ppc) boots to blue screen only

Hi, I realize that this is an old machine (10 years, at least) but until a few days ago it was working fine. I use it only for the FCP Suite, which will not run on my new Intel-Based Imac.
Anyway, I was able to boot up from the CD and run both the Disk utility and the Hardware Diagnostic Test. It passed the Hardware test without problems and then the disk utility found a bunch of errors, all of which is fixed (I have run it several times and it now comes up at "ok" everytime.
Still, when I go to boot it up it takes forever and goes through the gray screen, then the blue screen, and does not go past that.
I am stuck. Any ideas about the next steps? Should I use the Firewire Target Disk Mode?
There is another internal hard drive (which also passed all the tests) and I am wondering if I should try to install the system onto that and then try to boot from that. Any ideas about that? And, if I were able to boot from that disk, any ideas whether or not I would be able to then see the primary hard drive to copy off the project I was in the middle of when it went down?
I know I have a lot of questions, but any insight would be greatly appreciated.
Thanks,
Debbie

Hi BDAqua,
Many thanks for your thoughtful reply. I have done as you said—actually, I tried it right after I read your post—and the wheel is still spinning on the blue screen, which can't be good! It may be doing something, as previously it would go to the blue screen and eventually lose the spinning wheel, but still...
So, I had also done a reset of the PRAM and, I think, the SMU. What's next, do you think? What do you think of the idea of installing a system on the second hard drive...too risky? And is there anything I should be vacuuming, or looking at inside the whale? I saw some others had recommended that for other reasons...
Again, many thanks,
Debbie

Hi, my iphone its in recovery mode and when i restore my iphone 5s loading show the blue screen and show note on itunes (unknown error 14) please i need your help please . thanks

Hi, my iphone its in recovery mode and when i restore my iphone 5s loading show the blue screen and show note on itunes (unknown error 14) please i need your help please . thanks

In the article Resolve iOS update and restore errors this is what it says about error 14:
Check your USB connections
Related errors: 13, 14, 1600, 1601, 1602, 1603, 1604, 1611, 1643-1650, 2000, 2001, 2002, 2005, 2006, 2009, 4005, 4013, 4014, or “invalid response."
If the USB connection between your device and computer is interrupted, you may be unable to update or restore.
To narrow down the issue, you can also change up your hardware:
Use the USB cable that came with your device, or a different Apple USB cable.
Plug your cable into a different USB port directly on your computer. Don't plug it into your keyboard.
Try a different computer.
If necessary, resolve any further issues with the USB connection, then with your security software.
If you're still seeing the error message, check for hardware issues by following the next section.

I powered off my Ipad and it is stuck on the blue screen and won't shut off. What can I do?

I shut down my Ipad but it has become stuck in shutdown mode on the blue screen and won't turn off. What can I do to turn it off and try to restart it?

Both buttons:

My sound has gone out and please don't tell me about PRAM because my MacBook keeps going to the login screen and I can't hear any start up beeps neither someone PLEASE help me

my sound has gone out and please don't tell me about PRAM because my MacBook keeps going to the login screen and I can't hear any start up beeps neither someone PLEASE help me

bcoady90 wrote:
My guess is a loose connection.
I suspect you are correct. I would suggest you bring it to a repair facility that may have better diagnostic tools, preferably an Apple store genius bar.
Ciao.

My macbook turns off randomly but not completely because when I tap the touchpad it goes to the password screen and I am back to it in seconds. It's really annoying. HELP!!!

My macbook turns off randomly but not completely because when I tap the touchpad it goes to the password screen and I am back to it in seconds. It's really annoying. HELP!!!

1. Non volatile random access memory (NVRAM) is where the computer stores user's settings, like time and date, speaker volume, energy saver settings etc.
2. Reseting NVRAM has no impact on anything on your hard drive, or anything else on the computer.
See this note from Apple: http://support.apple.com/kb/ht1379

I connected my laptop to the tv and it has worked before. this time only the laptop flashes the blue screen and the tv is saying no signal. when i tried to check the dispaly arrangement it says this:The Arrangement tab of Displays preferences is hidden

i connected my laptop to the tv and it has worked before. this time only the laptop flashes the blue screen and the tv is saying no signal. when i tried to check the dispaly arrangement it says this:The Arrangement tab of Displays preferences is hidden because you only have a single display attached to this computer.

It is not properly connected to the network.
Make sure location is set correctly
DNS should be on auto (settings - general - network)
Try ethernet
Signal strength on device won't account for issues, you would need a network report from istumbler, netstumbler or similar. This will show accurate signal strength along with noise and nearby networks

When I power up my mac, I see the white screen and the apple icon. After a few seconds of powering up the screen goes dark. Yet I still can the mouse arrow but nothing else.

When I power up my Imac, I see the white screen and the apple icon. After a few seconds the screen goes dark. I am able to still see the mouse arrow as I move it around. But nothing else. What is the problem and how do I recover?

Try this from another user:
1. Shut the computer down by holding the power button for 10 seconds
2. Restart the computer and press shift at the same time until you see the progress bar start moving
3. Once you reach the point where your screen goes dark and you see the cursor, type the first letter of the username for your computer, then hit Enter, then type your password, then hit Enter.
4. After a moment, you should see the spinning beach ball
5. Your screen should then move on to something along the lines of "Completing OSX Installation" (I can't remember the exact wording). Let it finish. After that it should go to your normal desktop and the issue should be fixed. (If your screen goes pitch black during this process, hit the space bar. I thought it wasn't working, but the screen was just sleeping).

My MacBook pro is less then a year old and when I try to shut it down it gives me the blue screen and the loading spinner but the doesn't do anything or shut down. I've already tried to reinstall Mac os x but that didn't work any ideas?

It stays on the blue screen forever until I manually shut it down

Cooper, please start a new thread. You'll get a wider audience and won't confuse Quintonaturner with issues that don't pertain to them. You don't know they have Office. Many Mac users don't. http://www.neooffice.org is a nice alternative, and so is http://docs.google.com/ as long as you don't have Exchange servers that aren't Mac OS X Mail compatible.

My MacBook Pro is now asking for a login. When I enter my passcode, it goes to a blue screen and back to the login screen. I saw several older posts, but nothing recently. I am running Snow Leopard.

My MacBook is now asking for a password. When I login, it loops to a blue screen, and back to the login. Incorrect logins create a shaking of the login screen. I tried restarting with the shift key depressed, with no luck.

I performed a hard shutdown, and upon start I could access my system without logging on. I'm not sure what caused the issue, but I have not booted up in almost a week.

IMac makes a loud beep on start up, won't load past the blue screen and the black ticking dial appears every few seconds in centre of screen.

Urgent help!
Out of the blue my mac lost the mouse cursor even though it had connection so I rebooted only for the mac to make a loud beep on start up then get stuck at the blue loading screen. It won't load past the blue screen. I've tried to reboot holding down the shift key but no change. I've also shut down, unplugged the main for 15 seconds, re plug and wait 5 seconds before starting up again but no change. Does anyone have any suggestions?
PS: I'm not too sure which systems I am running without being able to check in about this mac. I bought my imac in January or February 2011 if that helps.

The power on self-test resides in the ROM of the computer. This test runs whenever the computer is turned on after being fully shut down (the power-on self-test does not run if the computer is only restarted).
If a fault is detected during the test, you will not hear a normal startup chime. Instead, the system will beep as explained below. If you experience one of these beeps, you may call your Apple Authorized Service Provider for additional troubleshooting assistance.
1 beep = no RAM installed
2 beeps = incompatible RAM types
3 beeps = no good banks
4 beeps = no good boot images in the boot ROM (and/or bad sys config block)
5 beeps = processor is not usable
http://support.apple.com/kb/HT1547

Power Mac goes to the blue screen and no where

Similar Messages

Maybe you are looking for