Power on-off-on Problems with New Build Z68A-GD65(G3)

I'm hoping someone has seen these issues and can help me, although I realize this is a vague issue. I'm working on a new build. On power up everything looks good but then I get a power off and back on (like a reset). Sometimes it happens very quickly; other times it will stay on for roughly 5-10 minutes before the reset. I've checked all the connectors, case wires look ok, BIOS info looks correct.
The other issue is that when I tried to do the Win 7 install, it loads the files, goes to the "Starting Windows" screen, and freezes there (until the next power off problem shuts things down).
Any ideas on what to try to narrow things down? Seems like it almost has to be the power supply or motherboard?

Quote from: Henry on 28-October-11, 09:54:40
You have more than a Z68A-GD65(G3), please list he rest of your components. See my signature below for example of what to list.
>> Posting Guide <<
I've disconnected everything but the mouse, keyboard and monitor and still have the power resets.
Tried one memory module at a time... still fails.
Played with lower memory freq settings... still fails.
Finally pulled the MB out, bench tested it to rule out shorting in the case; tried it with and without other peripherals... still fails.
I think I'll RMA the MB, although I suppose it could be the psu (unlikely, I'd think).
I had two bad motherboards in my last build. I had hope that MSI would be better...

Similar Messages

Problem with new build, Motherboard/Case

Hi, I bought a new pc that arrived Friday, It is my first build so bare with me on some bits.
But to cut it short I have the NZXT Phantom case with a P67A-GD53 Motherboard, And when I screw it all down to the case I cannot fit my GPU in (GTX 570 Power Edition) It gets blocked by the PCI slots at the back, And at first I didnt have my I/O Shield on, But took it off and instaled that and now the motherboard physically cannot screw in at the top without me bending the board..Do I have a dodgy case, Am I installing wrong or just missing the obvious like a moron ?
Any help much appreciated

Quote from: smify123 on 02-October-11, 18:21:46
or just missing the obvious like a moron ?
Turns out this was the answer -_- I just didnt have the stand off screws installed lol

Wifi problems with new ipad

I'm trying to learn how to correct wifi problems with new iPad. It is the wifi only, 64GB model. I want to be able to use it at work, where we have a great wifi network. I can usually connect to our network with no problem, but after an hour or so my iPad loses the network. When I try to reconnect, I see that the network is showing full strength reception, but I get the error message from the iPad that I am "Unable to join" the network. My iPhone connects to the same network seamlessly, as do all of the other iPhones of my co-workers and the older generation iPads that some of our staff has.
At other locations, I typically have no problems (home, apple store, etc.) but I have had the same situation pop up at a coffee shop where I could see that there was a wifi network available, but I could not join it even though it was the shop's free wifi.
I have tried turning the iPad off, turning off wifi and turning it back on again, and forgetting the wifi network in question. I can't think of any other methods that are available to an end user to correct the problem.
I have already gone to the Apple store to swap out the unit, and the newer one is having the same symptoms.
Can anyone offer any advice here? This is quite frustrating.

No problem! Have a read at this most interesting article which has special significance as regards your models!
http://edition.cnn.com/2012/04/05/tech/gaming-gadgets/ipad-wi-fi-issues/index.ht ml
However, I attach an extract from another thread for your perusal. You can disregard any suggestions/links you have already explored -
created by Texas Mac Man in Using iPad - View the full discussion
Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
 Cheers, Tom ;)

Problems with new catalyst

I Have a problem with newer catalyst version 4.7 and 4.8..sometimes the screen goes totally black,it's like the montitor goes into sleep mode or screensaver.
This can happen at startup or after while the only thing i can do is to restart the computer by turning it off(or reset).
With cat 4.6 and the drivers before everything works fine.
I tried fastwrites on/off(no good)
Disable Vpu recover(no good)
Raise agp voltage to 1.6V(no good)
I also tried asus own driver but the same thing happens.
However i came to think of if there is anything i should change in power managment in bios because the comp won't wake up from sleep mode when pushing on the keyboard or moving the mouse(this is with cat 4.6 wich works great otherwise)
I hope someone have an answer to my mysterious problem

Quote
Originally posted by Ycore
This is my exact problem. Computer has been running ROCK solid for the last few months with 4.7 catalysts. I install the 4.8's, reboot, load up Doom 3, and the computer hard locks within seconds of 3D mode being activated. Reboot, run 3dmark2001, and again, hard lock within a few minutes into the demo (screen goes black into power savings). At this point I figure it's a problem with the 4.8's, so I reinstall the 4.7's, fire up Doom 3, and IT FREEZES AGAIN.
At this point, I'm loathing my decision to mess with my vid drivers at all, and wondering how come the vid card has started to lock up in 3d.. I start messing with all sorts of settings.. Finally, tuning the AGP speed from 8X to 4X totally resolved the freezes.
QUESTION: WHY ALL OF A SUDDEN DID 8X AGP STOP WORKING???
AMD 64 3200+
K8T-NEO
Antec 430W PSU
ATI RADEON 9600 PRO AGP
SB LIVE
1GB CORSAIR C2 DDR (2x512)
Lite-ON DVD/CD+RW
Windows XP SP2
I have never got my 8x AGP to work, its always hard locks when I use it...dunno why I don't really care. When I upgrade to a pure 8x AGP card i might if it still happens. Actually if it continues to happen there is a good chance I will get rid of this board and get the nforce probable. But at any rate, setting AGP to 4x has always fixed every video card problem I have had since putting this computer together. So try that I suspect it will fix your problem as well.
Also note that we have very similar setup's so try it and let us know if that works out for you.

Problem with Weblogic Builder SP1

I have a problem with Weblogic Builder SP1. I basically re-used my EJB deployment
descriptors from WL5.1 in WL8.1. Before SP1, i have no problem loading my EJB
in WB. But with SP1, WB throws weblogic.marathon.model.LoadFailureException.
I re-attempted by jarring my EJB with WL5.1 descriptors and used my friend's WB
(not SP1) to export new descriptors which I used to re-jar. This new EJB is again
not recognised by WB SP1?
What is wrong?

The exception is as follows:
Opening module myproj.jar
java.lang.NullPointerException
     at java.util.Arrays.sort(Arrays.java:1181)
     at weblogic.marathon.model.EJBJarCMBean.initRelations(EJBJarCMBean.java:1212)
     at weblogic.marathon.model.EJBJarCMBean.initBeans(EJBJarCMBean.java:1098)
     at weblogic.marathon.model.EJBJarCMBean.setup(EJBJarCMBean.java:1144)
     at weblogic.marathon.tasks.OpenModuleTask.getEJBModule(OpenModuleTask.java:156)
     at weblogic.marathon.tasks.OpenModuleTask.figureOutModule(OpenModuleTask.java:191)
     at weblogic.marathon.tasks.OpenModuleTask.figureOutModule(OpenModuleTask.java:230)
     at weblogic.marathon.tasks.OpenModuleTask.runBackground(OpenModuleTask.java:89)
     at weblogic.tools.jellybeans.core.task.TaskThread.execute(TaskThread.java:127)
     at weblogic.tools.jellybeans.core.task.TaskThread.run(TaskThread.java:64)
Module myproj.jar descriptors failed to load
The EJB has no problem deploying.
Rob Woollen <[email protected]> wrote:
You'll have to at least show us the error you get from marathon.
Does your application deploy to the server?
-- Rob
Robin Tan wrote:
I have a problem with Weblogic Builder SP1. I basically re-used myEJB deployment
descriptors from WL5.1 in WL8.1. Before SP1, i have no problem loadingmy EJB
in WB. But with SP1, WB throws weblogic.marathon.model.LoadFailureException.
I re-attempted by jarring my EJB with WL5.1 descriptors and used myfriend's WB
(not SP1) to export new descriptors which I used to re-jar. This newEJB is again
not recognised by WB SP1?
What is wrong?

Problem with Folio Builder - added articles are "spinning"

Hello,
today we are experiencing strange problems with Folio Builder. We are adding new artcles to folio created today and all added articles have same issue - spinning wheel in folio builder. Such articles we can't see in Content viewer until we delete existing folio.
Thanks for help

Hi,
Could be that there was a network problem when uploading the InDesign documents.
Try to select the articles and delete them with the trashcan. And then reupload the documents from InDesign.
Good luck!

Problem with new version 4.3.2 apps not working " after update to the new version "

Problem with new version 4.3.2 apps not working " after update to the new version "
i was in 4.3.1 then i do the update , but now after update i face this problem , so what i Supposed to do ?!!

Hi There
Had the same problem as you. App would terminate when launched.
Solution to working You Tube app:
-Go to playstore
- Uninstall app (it doesn't remove the app, only removes the update)
- "Et Voila", working again.
This doesn't correct the problem, it's just a workaround for you to be able to use youtube app again.
Hope it helped.
Best Regards

I bought new i phone 5 3 days back, after that asked for new update which is 6.1.4, after updating my iphone i am not able to use cellular data services. I called up data provider, they says its the problem with new software update. There is no option add

I bought new i phone 5 3 days back, after that asked for new update which is 6.1.4, after updating my iphone i am not able to use cellular data services. I called up data provider, they says its the problem with new software update. There is no option add APN. Now when i switch to safari its showing you are not subscribed for cellular data. But I am able to use data on other phone.
Will you please help me in this regard?
Another issue, since i bought my new iphone there is dust inside back main camera.
Your advises are highly appreciated.

Hey Shaiju isac,
I'd take a look at the following article, it'll guide you though steps to you troubleshoot cellular data issues on your iPhone:
iPhone: Troubleshooting a cellular data connection
http://support.apple.com/kb/ts3780
Cheers,
David

List of Problems with new Web Mail

List of Problems with NEW Web Mail :
- At first doesn't open full page message list or retain full page as default setting, have to drag down bar
- Only shows 20 message lines after “pulling down” the divider, screen partially empty until I scroll down. It should show at least 26, preferably all available
- After moving bar, bar moves back up after going back to inbox (not delete message) after reading a message, have to move it down again, and again...
- Doesn't go to next message when delete message on screen is selected, no setting option for default to do this.
- There is a drop down to select which folder to move a selected email to. The initial display shows 7 usable choices, with the usual slider and arrow to show more choices. The space on the slider clearly shows more choices are present (actually about 20 or so are there), but any attempt to use the slider or arrow to see more choices causes the drop-down to instantly disappear. I can't move the selected field with arrow keys either. I can select any of the visible 7 choices, and move an email to only one of the 7. NOTE: This one works in both IE and Firefox, but if Verizon Webmail was fully web standard (see http://en.wikipedia.org/wiki/Web_standards) compliant it would also work in my preferred browser, Mozilla Seamonkey, the direct descendant of the original Mozilla browser. Webmail should be FULLY web standard.
- Occasionally a message will move from inbox to trash, without NO indication or command to move them.
- Emails occasionally flash an error message and simply disappear - not to trash or other findable place, just disappear. No time to read the error message either.
- No way to set a whitelist for supposed spam emails, unless the whitelist for “Blocking” is the same. Very unclear.
- How can I switch my service back to the original, basic, email which works ok? I know it’s still there, since some of my other accounts still access it!!!
This seems my only way of getting this info direclty to the programming staff. If it doesn't actually do this, will SOMEONE PLEASE FORWARD THIS MESSAGE TO THEM !?!
Thanks!

vz_ric wrote:
The majority of websites are set up the same way for all browsers. It's the software manufacturers responsibility to make their software compatible with websites, not the other way around. Otherwise everyone who has a website will have to make 10 different sites to work multiple browsers.
Contrarily, it is Verizon's, as well as other companies like Verizon whose customer base uses a wide variety of web browsers, web page designers' responsibility to use only standard W3C-recognized code and not to use non-standard non-W3C-recognized code, e.g., Microsoft's Internet Explorer specific code, when designing their web pages. In my opinion based on my observations, Verizon's web page designers are too often guilty of using IE-specific code.

Adobe aftereffects is not working on os x maverics all updates...... is dis soft. will work on the new os x yosemite.?? y apple is nt working on dis problem wen users are facing problems with new os x .....

Adobe aftereffects is not working on os x maverics all updates...... is dis soft. will work on the new os x yosemite.?? y apple is nt working on dis problem wen users are facing problems with new os x .....

I suggest you contact Adobe tech support or their Mac forums for assistance.

Reposting this If your having problems with new Windows 8.1 do a full uninstall of all Apple

Reposting this If your having problems with new Windows 8.1 do a full uninstall of all Apple iTunes programs but uninstall them in right order and then do restart of computer then reinstall newest iTunes and it will all be fixed up syncing problems or other problems this is thanks to Apple phone support

What is your technical support question for these user to user technical support forums?

Strange problem with my build JAR

Hiii everybody... I'm having a strange problem with my build (JAR file)... when I work with the Eclipse and I click in the table that returns the clients stored in my PostGre database it works fine, but when I build my application and it generates my JAR file and I open it and click in the same table to return the objects that I have.. it does not appears anymore.. just show when I work with eclipse... and the database is the same for both.
I already checked the database path in my properties file... and the application recognize the database because I can login and there isn't any runtime exception...
In that application I work with Hibernate and Spring... for me it is very strange because the application works fine when I run by eclipse... but does not return the database data when I click on my Jar file to open the application..
Someone can help me with that?
I dont know if the problem is in the Spring, Hibernate, Libraries...
thanks in advance...

So what's the error then? Are there any error messages? Have you checked the console? Or are you just clicking on the jar and you wouldn't even see the errors if there are any?
What do the logs say?
You're not giving a lot to work on here.

When Apple solve problems with new iTunes calendar sync with windows and outlook?

When Apple solve problems with new iTunes calendar sync with windows and outlook?

Anything Downloaded with a Particular Apple ID is tied to that Apple ID and Cannot be Merged or Transferred to a Different Apple ID
More Info here...
Apple ID FAQs > http://support.apple.com/kb/HT5622
If necessary...
Contact iTunes Customer Service and request assistance
Use this Link > Apple Support iTunes Store Contact

Before I buy has there been any problems with new 27 iMacs?

Before I spend my hard earned cash does anyone know if there has been any problems with new 27 iMacs?

Hello richard from Folsom:
Are you inside or outside? ( I could not resist, I lived in Sactown).
Anyway, advice is frequently worth what you pay for it, and mine is free.
If you want it, buy it. The posts above are right on the mark (except waiting is probably overly-cautious). The best advice (from anamusic) is to buy the extended warranty - well worth the money.
Barry

I just started using my iphone 5s. I have a problem with new incoming emails from my POP account. Why are they marked as read automatically even though I have not even opened them yet.

I just started using my iphone 5s. I have a problem with new incoming emails from my POP account. Why are they marked as read automatically even though I have not even opened them yet.
At first I thought it might be because I was using simultaneously my old iPhone 4S so it somehow realized the emails where being pushed to another device and the it marked as read, this has nothing to do since I have deleted the email account from the iPhone 4S

Contact the email provider for assistance with their service.

Power on-off-on Problems with New Build Z68A-GD65(G3)

Similar Messages

Maybe you are looking for